Search Documents

By H. Zhu, Q. Jiang

The leaching kinetics of iron during the atmospheric direct leaching (ADL) of marmatite concentrate was studied under the following conditions: reaction temperature of 343-383 K, slurry pressure of 0.3-0.7 MPa, particle size of (-74 ?m, +63 ?m), (-63 ?m, +44 ?m), (100%-44 ?m). The statistical effects of reaction temperature, total pressure and particle size of concentrate on the extraction and the leaching rate of iron were analyzed. The results show that reaction temperature is a significant factor while slurry pressure and particle size are not statistically meaningful with respect to the extraction or the leaching rate. The extraction of iron fits better to the mixed-controlled shrinking core model and the apparent activation energy was calculated to be 37.66 kJ/mol. The leaching of iron is mixed controlled by the interfacial chemical reaction and diffusion across the product layer.

Jan 1, 2014

By O. A. Carson

"IntroductionTHE ZINC-BASE die casting alloys in common usage contain approximately 4 per cent aluminum as the major alloy element. In addition, they contain about 0.05 per cent Mg .and may• have a small amount .of copper. These are usually the only •elements intentionally present.Small amounts of some impurities have been shown to have a deleterious effect on the properties of these alloys and therefore the impurities are kept low by starting with '99.99%' zinc.The reasons for holding the aluminum content at 4 per cent are not clear. Some statements appear in the literature that higher aluminum increases the brittleness, but probably the chief reason was the relative price of zinc and of aluminum when 4% alloys became firmly established. At that time, aluminum was three to four times the price •of zinc on a weight •basis. Recent prices, roughly equivalent per lb., make aluminum considerably cheaper than zinc on a volume basis and suggest that increased aluminum content would result in a decrease in the cost per piece due to the lower density of the alloy.Little information could be found in the literature and, therefore, it was decided to determine some physical properties of the higher aluminum zinc-base alloys made from high-purity zinc."

Jan 1, 1953

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

By Marcio Luis S. Godoy

The Salobo Project will be the first Vale operation to use an HPGR mill to process copper-gold ore. The mine is located in Para state, southeast of the Amazon region in Brazil. The circuit was designed to treat 12 million metric tons per year of finely disseminated sulphide ore with high hardness. The comminution circuit comprises a gyratory primary crusher, secondary crushing utilizing two cone crushers, two 2 x 1.5 m HPGR operating in closed configuration with 6 mm screens, followed by two 26 x 40 ft ball mills. The concentration circuit consists of two rougher flotation stages using mechanical cells, regrinding with vertical mills, three cleaner stages with columns and one cleaner scavenger stage in mechanical cells. The concentrate is dewatered, filtered and transported by trucks and train to the port, to be exported. The circuit was designed on the basis of data obtained from a comprehensive laboratory and pilot plant campaign. The ore variability was assessed through simulation using data from a drilling core characterization program. The start-up of the industrial plant is planned for 2011. This paper describes the main aspects of circuit design, as well as information related to the beginning of the project construction.

May 1, 2010

By B. Yu, Y. O. Oyediran, M. Robart

"This paper presents the latest flotation development testwork conducted in 2015 on the ‘B Zone’ samples from the Strange Lake Alkalic Complex (SLAC). Since the discovery by Iron Ore Company of Canada (IOC), metallurgical development has been under taken by a number of mining companies targeting various value metals, including yttrium, zirconium, niobium, and rare earths.Most recent, Quest Rare Minerals Ltd. (Quest) completed a Pre-Feasibility Study (PFS) in 2013 where the flowsheet was relatively complex and led Quest to explore alternative options. In 2014, the PFS flowsheet was simplified and one of the features introduced was pre-concentration by rougher flotation. The combined rougher flotation concentrate and slimes successfully recovered >90% TREE in 60% mass thus reducing capital cost and technical risks of the downstream hydrometallurgical processes. The latest flotation development testwork focused on achieving a pre-concentrate in which >80% TREE are recovered in 20% mass. Two separate reagent schemes, based on an ester phosphate collector (Clariant 1682) and a benzoylhydroxamic acid collector (Florrea 7510), were developed. Parameters evaluated in the development testwork included desliming, secondary yttrium and zircon collectors, depressants, temperature, conditioning temperature, time, and density, pH, sodium silicate type, cleaning, and flowsheet configuration. Both developed reagent schemes achieved the targeted metallurgy.INTRODUCTIONThe Strange Lake Alkalic Complex (SLAC) was discovered after geological survey and mapping studies by Geological Survey of Canada and Newfoundland and Labrador Department of Natural Resources between 1967 and 1980. Subsequent exploratory drilling programs by Iron Ore Company (IOC) in the 1980s found that the REE and high field strength element (HFSE) mineralization were within the central region of the SLAC which was named A Zone by IOC and later renamed Main Zone by Quest Rare Minerals Ltd. (Quest). Additional exploratory drilling outside the Main Zone by IOC and later by Quest, led to the discovery of B Zone, which was recognized as the most significant deposit of rare earth elements, yttrium, and zirconium in the SLAC. The B Zone Indicated Resources are estimated at 278.13 Mt at 0.93% total rare earth oxide (TREO) and Inferred Mineral Resources are estimated at 214.35 Mt at 0.85% TREO (Oyediran et al., 2014)."

Jan 1, 2016

By J. A. González-Anaya, F. Nava-Alonso, O. Alonso-González, F. Alvarado-Hernandez, A. Uribe-Salas, C. Jimenez-Velasco

"One of the most common hydrometallurgical methods for precious metal extraction is cyanidation. The effluents of this process may contain relatively high concentrations of copper, zinc and iron, which react with free cyanide to form complexes, adversely affecting the efficiency and the economy of the process.This preliminary work studies the use of the solvent extraction technique to remove copper, zinc and iron cyanide complexes from a synthetic solution similar to that of gold mill effluents, in order to allow the recycling of the solution back to the process. For the extraction of these anions (Cu(CN)2 -, Cu(CN)3 2-, Cu(CN)4 3-, Zn(CN)4 2- and Fe(CN)6 3-), trioctyl methyl ammonium chloride (Aliquat 336) was studied as extractant, using nonylphenol as modifier in the organic phase (iso-octane). The experimental results showed that for a synthetic solution containing 450 mg/L total cyanide, 160 mg/L copper, 50 mg/L zinc and 51 mg/L iron, it is possible to extract the 96% of copper, 91% of zinc and 75% of iron when using 0.011 mol/L of Aliquat 336 (organic/aqueous volume ratio (O/A) =1) in the pH range of 9-10."

Jan 1, 2014

By Robert B. Parsons

"The 1994 Quebec Budget included a significant overhaul of the mining duties sys-tem in that province: broadening the base and lowering the rate, all in the name of “ensuring the integrity of the taxation system"" and ""enabling the State to collect fair compensation "". The reforms hit hardest on the small, lightly-capitalized producer, by repealing the basic annual exemption, limiting the refund for losses, and significantly reducing the investment and processing allowances. There is some relief provided in the form of faster depreciation rates and a lower nominal tax rate, but the thrust of the overhaul is clear -higher taxes on the mining sector.IntroductionAlthough Quebec's mining tax regime represents under 10J0 of the province's revenue base, and was significantly reformed in 1979 and 1985, the May 13, 1994, provincial budget introduced further significant changes to the Mining Duties Act, The hope (on the part of the province) is to reduce the provincial ""subsidy"" for mining by $20 mil· lion per year by 1996."

Jan 1, 1995

By M. Al Mukhtar, D. Hoxha, X. Brunetaud, D. P. Do, C. Auvray, L. Michel

"Mechanical behavior of rock joints is often the key factor governing the response of complex structures constructed in fractured rock masses such as underground openings or of objects assembling various stones blocks such as historical building walls or damaged marble statues. This paper aims at developing a theoretical model to describe the behavior of fresh joints based on the description of their morphology. The main idea of the model is to establish a link between the effective contact surface of joints and the frictional coefficient. Beginning from a chosen level of joint surface description where a joint is considered as “smooth”, the model describes the added friction with respect to the increase of the contact surface of the joints and the distribution of stress in these contacts. The model developed initially for asperities with regular geometry is firstly compared with existing models and then applied on fresh artificial joints. For that, healthy artificial joints have been characterised using in one hand classical CNL shearing tests and in another hand the morphology of joints. The joints surfaces are digitized before testing using a high resolution laser scanner (Konica Minelota Vivid 910) allowing to obtain a precision up to 10µm. From these scanned surfaces the morphology of joints is characterised on the profiles running in the direction of shearing and a mean value of friction is calculated using the developed model. This calculated value is then compared with that obtained from CNL shearing test and a good approximation is notedINTRODUCTIONThe role of the mechanical behavior of rock joints on the overall response of fractured rock masses is well established in many fields of engineering activity going from the stability of underground constructions (Souley M, Hoxha D, Homand F 1999), rock slope stability (Einstein H.H. Veneziano D., Baecher GB., O’Reilly K.J, 1983, Jaeger 1971), various rehabilitation of masonry construction, damaged stone artworks restoration (Michel L., Do D.P, Coignard B, Hoxha, 2014) and so on. In the same time the characterisation of the behavior of joints and their modeling is nowadays a dynamic field of research or/and investigations and many alternative approaches have been proposed (Barton, N.R. and Choubey, V. 1977, Tatone, S.A. Bryan, Grasselli Giovanni 2010, William C E. 2007). While empirical relations of shear strength with various parameters of the joint morphology are the most used in practice because of their simplicity (Barton. and Choubey, 1977, Barton 1973, Bandis S., Lumsden A. C. and Barton N. R. 1983) many other models of joint strength are developed based on mechanistic considerations (Haberfield CM, Johnston IW. 1994), multiscale approaches (Yang Z.Y., Di C.C., Yen K.C. 2001, Fardin N., O. Stephansson, Lanru Jing 2001) or micromechanical ones (A. Serrano, C. Olalla, R.A. Galindo 2014) to mention just a few of research trends on rock joints modeling."

Jan 1, 2015

By Xing-Liang Sun, Xian-Min Han, Zheng-Guo Zhu

The study on the material properties of frozen soils in China was being developed quickly in the past decades of years, because of the increase of the engineering constructed in frozen soil regions on the Qinghai–Tibet Plateau, and numerous research results were achieved mainly about strength and deformation behaviour and constitutive models of frozen soils. Studies have shown that the deformation procedure of frozen soils is irreversible; therefore, it is more appropriate to research mechanical properties of frozen soils by means of damage mechanics theory. In this paper, an elasto-viscoplastic anisotropic damage model is presented by introduction of Perzyna viscoplastic equation into analyzing the deformation of frozen soil. In addition, an anisotropic damage evolution equation is obtained by means of extending non-viscous damage to viscous damage. Triaxial tests at different strain rates are chosen to illustrate the application of this model, and good agreement between experimental data and numerically simulated results is obtained. The calculated results indicate that, under the same conditions, the damage at higher strain rate is less than that at low one. So the phenomena are explained from damage mechanics that the frozen soil has larger elastic modulus and shear strength at higher strain rates, and explained from mechanism that the emergence and development of micro-cracks in the body of frozen soil can be to some extent retarded at higher strain rates.

Jan 1, 2015

By Matej Petružálek, Tomáš Svitek, Tomáš Lokajícek

"Migmatite from the Skalka region (Czech Republic) was chosen as the experimental rock material. It has macroscopically visible plane parallel structure (foliation). The foliation was caused mainly by biotite grains arrangement. The cylindrical samples of migmatite with subhorizontal, subvertical and oblique foliation were uniaxially loaded up to the failure. Network of 8 broad band sensors was employed for acoustic emission monitoring and ultrasonic sounding. A grid search method with anisotropic velocity model was used for AE hypocenters localization. The source types of successfully localized events were determined from the average first arrival amplitude. Structural anisotropy of tested rock material caused the anisotropy of its mechanical properties (peak strength, Young’s modulus) as well as a different way of fracturing process in dependence on the angle between axial stress and foliation plane. The combination of splitting, shearing and sliding was found to control the fracturing of sample with subhorizontal foliation. The shearing and sliding was dominant in fracturing of samples with oblique foliation. With greater dip of foliation, the role of sliding increased at the expense of shearing. Due to the favorably oriented system of microcracks already present, the shearing and splitting was at the same level during fracturing of the sample with subvertical foliation before nucleation began.INTRODUCTIONThe process of failure of low porosity rocks depends on their mechanical properties and actual stress and temperature condition. At the low pressure and low temperature, the most common way is brittle failure, which is a progressive process requiring the initiation, growth and coalescence of cracks (Lockner, 1993). Stress strain behavior of low porosity crystalline rocks, during the laboratory compression experiments, is divided into four characteristic stages: crack closure, elastic region, stable crack growth and unstable crack growth which leads to the brittle failure, Brace et al. (1966) , Bieniawski (1967), Lajtai (1974), Cai et al. (2004), Nicksiar and Martin, 2012 and 2013.The fracturing process of stressed rock begins with the crack initiation (sci), which for low porosity rocks occurs approximately at 40-50% of peak strength (sp) (Cai et al., 2004; Nicksiar and Martin, 2013). After the sci, the dilatancy begins and stable crack growth follows up to the crack damage threshold (scd), which is approximately at 80% of sp (Cai et al., 2004). After crossing the crack damage level, there is an unstable crack growth accompanied with nucleation of fault plane (sn) at 97-100% of sp. (Rao et al., 2011). The stress drop accompanied with formation of macro scale shear failure plane follows after peak stress is crossed."

Jan 1, 2015

By Jian Deng

Rockbursts are sudden and violent failure of rocks in deep and/or high stress mines, which may destroy the excavation space and cause an accident or even the death of mining workers. This study is motivated by the pervasiveness of rockbursts all round the world. It has been found that rockbursts are often stimulated by dynamic fluctuation which is generated by mining operations or other sources of vibrations, such as blasting in adjacent stopes. This paper attempts to investigate the dynamically stimulating mechanism of pillar rockbursts in hard rock mines from an innovative point of view. Rockbursts are classified into triggered rockbursts and induced rockbursts in accordance with the magnitude of the stimulation force. Triggered rockbursts occur only when a small fraction of stress changes associated with rockbursts is accounted for by the causative excavation, whereas induced rockbursts happen where the causative factor is responsible for most of the stress changes required to produce the rockburst. By considering rockbursts as a dynamic instability problem of structures, rigorous mathematical models are set up for triggered rockbursts and induced rockbursts, respectively. By using the method of averaging and the method of eigenvalue problems, the boundaries of rockburst occurrence of a pillar are obtained for these two rockbursts. A new explanation of the failure mode of fretting or necking of pillars is given, the perturbation effect for pillar rockbursts is found, and the parametric resonance mechanism of pillar rockbursts is revealed. The quantitative relation between blasting parameters and pillar rockbursts obtained can be directly used to control the rockbursts. Contrary to conventional methods where only rock materials or rock specimen were used to study rockbursts, this investigation attaches more attention on the structural effect on rockbursts, which have strong potential applications in deep mining.

Jan 1, 2015

By Lawrence Devon Smith

"This paper examines the impact of the various assumptions that go into an economic evaluation, and shows how these can be combined to show an exciting result that may not really exist. An example of an embellished case (the kind that one frequently sees when projects are being promoted) is developed and the cumulative impact is analysed to show the actual project underneath. The paper also points out some areas to watch for overly optimistic assumptions such as prices, inflation, and debt. The concept of a ""bare bones"" base case is proposed (constant metal prices, constant dollars, no inflation, no debt, no interest, on a project basis, after tax) as a common reference point.As well, the discount rate is examined as a fundamental means of reflecting risk in discounted cash flow evaluations. Current industry practice is discussed, and a methodology for the analysis of risk levels is proposed that assesses the constituent components of the discount rate: real interest, mineral project risks, and country risk.INTRODUCTIONOften, the first time that all of the technical and economic data for a mineral project comes together in one place is when the economic evaluation is developed. This typically happens when work on the project has progressed to a sufficient level of detail that the effort to produce a year-by-year cash flow is justified, usually at the pre-feasibility or feasibility study stage. The data involved will include:• production; tonnes waste and ore mined, ore grade, mining recovery, metallurgical recovery, metal sold• revenue; metal price, smelting & refining charges, marketing costs• operating Costs; mining, milling, administration, fees, royalties• capital Costs; exploration, development, construction, indirect costs (engineering, management), contingencies, start-up, inventories, working capital, replacement and sustaining capital, closure costs• taxes and royalties• exclusions; depreciation (this is not a cash item), sunk costs (only costs going forward)."

Jan 1, 2003

By W. L. Falconer

"IntroductionThe very recent emphasis on the importance of the northern portions of the Alberta basin as a prospective oil province has led the oil companies northward into new and undeveloped territory. Northern Alberta is a land of continuous forest, covering a plains-type topography. The plains are only occasionally broken by sharp, broad river valleys. Tributary streams head up quickly and very soon lose themselves in large undrained areas. It is these pseudo-swamps that cause most of the troubles and headaches of the oil explorer.The rivers have served as the main transportation arteries since people first ventured into this area. The bush is being pushed back, but the advance is slow and there is very little more than trappers' trails beyond a few miles from the Northern Alberta Railway lines and the recently built Grimshaw or McKenzie Highway. Indeed, bush and muskeg flank many miles of the railways and roads within as close a distance as fifty miles of Edmonton. Northern Alberta is pioneer country in the truest sense of the word, and our greatest problems derive from this fact. In all pioneer areas, the first requirement is the development of access roads, and before active oil exploraton can get down to the job at hand these roads and trails must be an accomplished fact. There are two factors in Northern Alberta which offer discouragement to the oil explorer: the first and greatest stumbling block is presented by the numerous muskegs, large and small; the second is the fact that road building uses up so much of reservation time. Of course, the second is aggravated by, and a direct result of, the first. So we come back to the main problem facing the development of the north - the muskegs."

Jan 1, 1950

By Steve Custer, Chris Bennett, Patrick Garretson, Glenn Dobby, Jacques McMullen

"Barrick Gold is in the process of expanding one of its grinding circuits at the Goldstrike property as a response to both increasing ore hardness and increased ore sensitivity to finer grinding as it relates to gold recovery. The plant currently operates with two parallel grinding lines, each with a SAG mill, a pebble crusher, and a ball milling arrangement. As part of determining what additional equipment was to be required, a CEET evaluation program was conducted (CEET is an acronym for Comminution Economic Evaluation Tool). The work included: Development of a hardness ‘model’ for the ore body, as described by SAG Power Index and Bond Work Index;Site benchmarking surveys to fine tune the SAG and ball mill calibrations within CEET;Conducting CEET studies to examine the process options;Comparing CEET results to standard grinding circuit design techniques.The recommendation of the study, presently being implemented, is the installation of an additional ball mill on one of the two grinding lines. This paper reviews the sizing techniques applied, providing a CEET case study for circuit performance analysis and circuit design. OVERVIEW OF COMMINUTION AT GOLDSTRIKEOre feeding the autoclaves at Goldstrike are first processed through two parallel grinding lines. Both lines use SAG mills with cone crushing of pebbles followed by ball milling. A summary of the key circuit parameters is provided in Table 1. Line 1 primarily processes underground Meikle ore, although when no Meikle ore is available, it processes open pit Betze ore. Line 2 processes Betze ore exclusively. The Mill Line 1 P80 objective for Meikle ore is 74 microns. According to the recovery optimization analysis, a P80 of 90 microns was recommended for Betze ore. The potential however exists to perform co-mingling of both ore types and feed the higher grade Betze ore to Line 1, in which case the P80 of 74 microns would be retained."

Jan 1, 2001

By J. F. Henderson

THIS paper relates to an area of more than 5,000 square miles in the Northwest Territories extending north from Great Slave lake and including-the Yellowknife, Beaulieu River and Gordon lake areas. Within the last three years much interest in the area has been created by the discovery of remarkably rich gold-bearing veins and the realization that thousands of square miles of unprospected ground are underlain by rocks like those in which the veins have been found. Probably there were more prospectors in this area in 1938 than in any other part of Canada. The area lies 650 miles north of Edmonton, and 425 miles north of the terminus of the Northern Alberta railway at Waterways, Alberta. The Athabaska and Slave rivers provide an excellent water route from Waterways to Great Slave lake for large oil and wood burning boats and barges which operate from the latter part of May to October. The only portage is around a 16-mile stretch of rapids on the Slave river between Fort Fitzgerald and Fort Smith. The town of Yellowknife, on the north side of Great Slave lake, has sprung into existence during the past year and is the centre for distribution of supplies for the Yellowknife-Beaulieu region. The Con-Rycon and Negus gold mines, which came into production in September, 1938, and February, 1939, respectively, lie about two miles south of the townsite. Excellent airplane service is available from Edmonton to Yellowknife and from Yellowknife to all parts of the area. The prospector and mining operator have come to rely almost entirely on the airplane for supplies and for the transportation of personnel, camp equipment, and canoes from Yellowknife to localities selected for intensive prospecting.

Jan 1, 1939

By Edward R. Rose

This paper summarizes and emphasizes the potential importance of Canadian rare-earth occurrences, and recommends that efforts to locate and evaluate rare-earth deposits should be increased. Increasing world markets, depending on intensive applied research into the numerous unique and remarkable chemical and physical properties of the rare-earth elements (REE), are developing; their properties and uses are becoming better known; methods of separation are much improved. The REE group comprises a Cerium (Light) subgroup of 7 metals and an Yttrium (Heavy) subgroup of 9 metals. REE are trace elements in many rocks and minerals, and major constituents of more than 50 rare-earth minerals, many of which are difficult to detect and identify. They occur preferentially in acidic and alkaline igneous and metamorphic rocks, including carbonatites, as well as in placer deposits, certain uranium deposits, phosphate rocks and others. The main ores now are bastnaesite (in Precambrian carbonatite), monazite and xenotime (in Recent beach sands) as well as uraninite and brannerite (in Huronian quartz-pebble conglomerate) and loperite (perovskite) and apatite (in alkaline complexes). World resources are summarized. Twenty mines in 1973 produced an estimated world total of about 31,000 tons of contained rare-earth oxides (REO), 19,341 tons of which came from one mine at Mountain Pass, California. A selected fifteen, of 315 or more Canadian occurrences, are briefly described and compared, and their relative merits indicated. Their abundance and variety suggest the possibility of finding high-grade deposits in many geological terranes in Canada.

Jan 1, 1979

By J. D. Clucas, N. Verbaan, T. Grammatikopoulos, D. B. Dreisinger, C. Forstner, M. Aghamirian

"Search Minerals is currently exploring the Port Hope Simpson (PHS) Rare Earth Element District in southeastern Labrador, Canada. The Foxtrot Rare Earth Element (REE) Project in the PHS District has a 43-101 resource estimate consisting of 3,410,000 tonnes of Indicated Mineral Resources and 5,850,000 tonnes of Inferred Mineral Resources. The indicated and inferred resources contain 1.07% and 0.98% total rare earth element oxide (including yttrium), respectively. The dysprosium and neodymium grades are particularly attractive at 218 ppm Dy2O3 and 1687 ppm Nd2O3 for the indicated resources and 208 ppm Dy2O3 and 1494 ppm Nd2O3 for the inferred resources. The mineralization remains open along strike and at depth and is only one of a number of attractive exploration targets in the Port Hope Simpson area. The REE minerals fergusonite and allanite are present. The ore can be beneficiated by gravity, magnetic separation and flotation to a recovery of +80% for the individual REE. Acid bake and water leaching may be used to extract REE into solution for subsequent purification and recovery. The extraction range for single stage leach tests were 91-96% for Nd, 84-87% for Tm and 92-94 % for Dy with modest acid consumptions. INTRODUCTIONSearch Minerals Inc. (Search) is exploring the 100% owned Port Hope - Simpson District in Labrador, Canada for rare earth elements (REE). This District is approximately 135 km by 12 km in size, and is highly prospective for heavy and light rare earth elements. A total of 11 REE prospects have been discovered in the District to date, including the Foxtrot. In addition, Search is exploring in the 100% owned Henley Harbour region and has joint ventures with Quest Rare Minerals in the Strange Lake region, and with Great Western Minerals Group in the Red Wine complex, all in Labrador. These exploration locations are illustrated in the Figure 1. The focus of this paper is the investigation of the mineralogy and processing of Foxtrot REE materials. The Foxtrot resource falls within the claims held by Search in the Port Hope Simpson REE District. The infrastructure available at Foxtrot is excellent with a deep water port, air strip and road and power infrastructure at Port Hope Simpson. Over $7 Million has been spent to date on exploration and development of the District. The Foxtrot has been explored using prospecting geochemical methods, geophysics (airborne and ground), channel sampling of surface outcrops, mapping and three phases of drilling (18,934 m total)."

Jan 1, 2012

By L. V. Kin, V. V. Lodeischikov, A. V. Byvaltsev, IRGIREDMET JSC, O. D. Khmelnitskaya, S. V. Petrov

"Irgiredmet Institute carried out the study on the development of gold recovery technology from refractory ore from a Russian deposit. The ore contained 1.1 g/t Au, 1.5% of pyrite and 2.4% of pyrrhotite. The recovery of gold achieved was 84.7% using gravity with generation of high grade recoverable gold concentrate and gravity middling. In the course of lime treatment, cyanidation of the middling followed by tailings detoxification the consumption of reagents was 13.0 kg/t CaO, 95 kg/t NaCN and 72 kg/t Ca(OCl)2 of the concentrate. This was capital intensive.In order to decrease the consumption of reagents, magnetic separation of the middling of the concentrates from gravity separation was added to this flow sheet. Pyrrotite recovered to magnetic fraction, which did not contain gold in accordance to this advanced flow sheet. The mass yield of pyrite goldbearing non-magnetic fraction decreased down to 1.5 times in relative to gravity middling. The slurry filtration prior to and after cyanidation allowed the organization of cyanide solution recycling.The results of pilot plant tests using the developed flow sheet showed that the content of pyrrhotite in the non-magnetic fraction decreased from 59.1% to 11.3%. The reagents consumption was 12 kg/t CaO, 3 kg/t NaCN and 16 kg/t Ca(OCl)2 of the pyrite concentrate. The total gold recovery using this flow sheet was 83.4%. Due to a decreased consumption of reagents, cost efficiency of the process was achieved. Based on the results of this research, a project design criteria was developed. A processing plant with the annual throughput of 2.6 million tonnes of ore is being designed."

Jan 1, 2016

By A. H. Ransom, M. E. Robb

The Salmita Gold Mine is located 240 air kilometres northea t of Yellowknife on the east shore of Matthews Lake. Salmita is one of several gold showings which are regionally associated with the steep easterly dipping contact zone between mafic, intermediate and fe lsic volcanics to the west and overlying finely laminated argillaceous sediments to the east. The volcanic assemblage forms a narrow 2 m to 7 m wide north to northwesterly trend ing Belt of Yellowknife Supergroup Archaen greenstone rocks. The contact zone exhibits exhalite character and the increased sulphide content provides a di stinct VLF-EM , IP/Resisti vi ty and/or magnetic signature. Gold occurs at or near this contact in three main settings: associated with si liceous vein-like structures; with finely disseminated sulphides within ericitic altered upper fe lsic tuffaceous unit ; or with quartz in narrow shear zones within the overlying sediment . The B-Vein is of the former type with free mi ll ing gold occurring within a highly sil iceous zone having an average widtn of 1.69 m. Alteration is intense within the immediately su rrounding host lithologies and includes the development of si lica, carbonate, sulphide, sericite and chlorite with minor graphite, epidote. tourmaline and scheelite. The mineable zone above the 4th level (-200 m) ha an average strike of 160 m and is divided into three south plunging ore shoots separated by the regional Salmita Shear Zone in the south and by a low-grade structural hiatus in the north. Production from the B-Vein commenced in August 1983 based on a diluted in situ ore reserve of 140,000 t grading 26.6 git Au . As of December 31, 1985, a total of 131 ,537 t grading 27.8 git Au have been mined at a ra.te of 160 t per day and a 96.4 percent recovery, to produce 3,522 ,000 g (113,227 ounces) of gold . Current (January I, 1986) reserves total 45,500 t grading 37 g/t Au down to the 10th level (-500 m) .

Jan 1, 1986

"An unparalleled growth in the Canadian coal industry in 1970 coincided with increasing awareness by Canadians of their environment and their geography with its accompanying transportation factors. R and D on coal moved with greater emphasis toward solving problems in these areas as well as continuing with strong interest in coal preparation, carbonization, combustion, ""weathering'', spontaneous ignition, storage, exploration and geology. Long-range ""basic"" research was not forgotten in that work continued on coal-based carbons, coal chemistry and agrobiological uses for coal. This paper reviews the status of these many areas of coal research at the beginning of the seventies and takes note of some of the more significant legislation and projects brought to the author's attention. No attempt is made to itemize or to describe in detail all the worthwhile projects, many of which are reported elsewhere."

Jan 1, 1971