Search Documents

By W. A. Gow, V. F. Harrison, H. H. Mccreedy

A semi-continuous bench-scale, countercurrent-decantation system, in which the ore was moved countercurrently to the flow of leaching solution, was used to conduct acid-leaching tests on uranium ore with the aid of bacteria. This method, which involved a low degree of agitation, was successfully applied to extract uranium in practical amounts and at practical rates. The acidity of the leaching solution was the main variable investigated in the bench-scale tests done at the Mines Branch, Ottawa. Over 90 11er cent of the uranium was extracted in a six-stage system. The results suggest that this technique could be ap-plied in the utilization of bacterial oxidation and leaching as a method for treating Elliot Lake uranium ore.

Jan 1, 1969

In the flotation of a copper ore, entrainment of fine silicate and iron sulfide gangue minerals resulted in poor copper concentrate grade. In the cleaning stage, rejection of these gangue minerals was particularly difficult due to severe mechanical entrainment when the rougher concentrate was ground to 10 µm. To reduce gangue entrainment, polymeric depressants were tested. The rationale being that with the use of such polymeric depressants that also possess flocculation power, not only minerals-to-be-depressed can be made hydrophilic, but their particle size can also be enlarged. In this manner both the "genuine" flotation and the mechanical entrainment can be reduced. An effective polymer to reduce entrainment of silicate gangue mineral in sulfide flotation was identified from bench flotation tests conducted on single minerals. It was then applied to the flotation of a copper-gold ore confirming the beneficial role of the polymeric depressant in the reduction of fine gangue entrainment.

Jan 1, 2007

By V. Bazhko, V. Yahorava

The calcium sulphate waste stream of the wet phosphoric acid process, commonly called phosphogypsum (PG), contains the majority of rare earth elements (REE) initially present in the apatite feedstock. Mainly light and middle REE are present in PG and their total concentration ranges from 0.27% to 0.35% by mass. Worldwide, around 7 billion tonnes of PG have been produced to date at a current growth rate of 150-200 million tonnes per annum. In total, an estimated 21 million tonnes of REE are locked in PG waste dumps around the world. Due to the value of the REE contained in PG dumps a number of processes have been devised for their recovery. The majority of these processes applied complete or partial gypsum dissolution, but were deemed not viable due to high capital and operating costs. Mintek developed an alternative method for the recovery of REE from PG by applying Resin-in-Leach (RIL) technology. This technology was tested on PG sampled from dumps and current arisings from South African phosphoric acid production plants. The extensive testwork program included evaluation of various lixiviants and optimisation of lixiviant additions, optimisation of REE leach and adsorption conditions, batch equilibrium and kinetic adsorption tests, continuous RIL testwork and numerous variability tests. It was found that PG from different sources was highly variable, both in terms of REE recovery as well as physical properties of the material such as viscosity and filterability of the slurry. The recovery of REE varied from 15% to 80% depending on the origin of the samples. A high-level economic study indicated that at a price of >21 $/kg for mixed REE oxide product in conjunction with an overall REE recovery as low as 15% the economics of REE recovery from PG via RIL technology may already be favourable.

Jan 1, 2016

By Magnus Evertsson, Johannes Quist

HPGRs have since introduced in the 1980s (Kellerwessel, 1993; Schönert, 1988), now become integral comminution units at several minerals processing plants around the world. Even though a lot of the initial issues concerning performance, availability and wear have been addressed and solved there are still phenomena and aspects which can be improved and understood further. Schönert and Sander (2002) presented experimental results and a mechanistic model including the internal force dynamics between the rollers and the compacted bed. They derived expressions for the pressure distribution involving most of the influencing terms and effects. However, in order to solve the differential equations several of the terms vanish by assumptions. The Schönert and Sander model reflects the experimental data in many aspects but the predicted shear force distinctly deviates from the experimental results at the angular position of the peak pressure level. This finding suggests that the particle to particle interaction and breakage process in the different zones seen in Figure 1 are complex and difficult to model using analytical models. A numerical modelling approach using DEM does not require the same amount of assumptions and simplifications of boundary conditions. Hence such modelling may provide further knowledge and vital understanding. In this paper the breakage process is simulated in order to investigate the shear slip behaviour and how it relates to different operating variables. A laboratory scale HPGR corresponding to the experimental setup used by Schönert (2002) have been modelled in EDEM (DEM-Solutions). The bonded particle model (BPM) is used for modelling quartz particles (Potyondy, 2004). The breakage model strength parameters are calibrated against interparticle breakage experiments in an Instron 400RD compression device. The contact model parameters are calibrated using calibration methods developed by Quist (2015). The floating roller dynamics are modelled using a spring-damper system. Results present insights regarding the interparticle slip behaviour as well as the frictional tangential force distribution on the rollers. The simulated roller pressure distribution shows good correspondence with previously reported findings in the literature.

Jan 1, 2016

By V. Aprahamian, G. B. Harris, C. W. White, M. Tangen

"In 2005, the Royal Canadian Mint (RCM) commissioned a new silver electrorefining circuit. This circuit was intended to operate with a minimal electrolyte bleed for the control of copper. However, by the time of start-up, the levels of copper-rich silver doré to electrorefining had increased, and despite partial pyro-conversion in a small Top Blown Rotary Converter (TBRC), copper concentration in the silver anode still averaged 7.5%. This necessitated frequent replenishment of the electrolyte with fresh silver nitrate since copper displaced dissolved silver during electrolysis, and therefore requiring a robust copper bleed treatment step in order to maintain cathode silver flake purity at 99.99%. The originally-installed bleed treatment system could not meet the RCM’s needs. A thorough review of known technologies, however, did not indicate one capable of handling the copper load, and resulted, therefore, in the development of a novel copper hydrolysis approach for removal of copper as an insoluble basic nitrate salt, and recovery of the associated nitric acid for re-use in the circuit. Laboratory-scale trials showed reproducible results, and existing equipment was subsequently modified.INTRODUCTIONIn 2005, the introduction of a new silver electrorefining circuit at the Royal Canadian Mint (RCM) initiated changes in the way customer silver, collected from the gold doré circuit, was processed. These circuit changes were discussed in a recent paper (Aprahamian, 2015). A wastewater treatment plant had not been budgeted at the time, and this represented a significant constraint when considering the introduction of a wet processing circuit. After a review of various options, a turnkey silver electrorefining circuit was purchased from a European firm. Initially, enough cells were ordered to produce 2 million oz of fine silver (999), with the option to increase to 5 million oz. The selected equipment was based on a Moebius cell design combined with a silver grain pressure dissolver to produce make-up silver nitrate solution. Additionally, an evaporator/hydrolysis unit included in the package appealed to the Mint Refinery, on the basis that it offered a simple way to bleed dissolved copper in electrolyte without generating effluent."

Jan 1, 2016

By N. W. Xu, M. D. Wei, F. Dai, B. Li

"Chevron notched samples achieve general acceptance for measuring the Mode-I (opening mode) fracture toughness of rocks. The cracked chevron notched semi-circular bending (CCNSCB) sample, which is developed from the International Society of Rock Mechanics suggested the cracked chevron notched Brazilian disc method, has recently received much attention. However, these chevron notched methods have not been fully mastered, some ideal assumptions based by their theories and formulas, such as the straight-through crack assumption (STCA), have not been verified detailedly. Fractures of CCNSCB specimens were numerically simulated considering different heterogeneities, geometrical and mechanical parameters. The results show that, the real fractures of CCNSCB specimens are never satisfied with the STCA. In fact, micro fractures not only occur in the notch tip but also the two chevron edges. Consequently, the crack front features prominently in a shape of parabolic curve, far from being straightthrough. Moreover, curvature of the crack front is only affected by shape of the chevron ligament. Cracks usually start from two sides of the notch tips rather than center of the notch width, and propagate deviating from the postulated fracture routes. These fracture mechanisms induce errors with the measurements, and thus more attentions should be paid to the real fractures of the chevron notched samples for measuring fracture toughness more accurately. INTRODUCTIONWith the increasing requirement of people for resources and energies, frequent rock engineering activities have been conducting, such as underground excavation, oil exploration and deep burial of nuclear waste. Many problems appear in rock fracture. Consequently, there are more and more attentions paid in rock fracture mechanics due to its broad application prospects for solving these engineering problems. Since Mode-I (opening mode) fracture is the most common failure mode in rocks, Mode-I fracture toughness is a primary parameter to predict rock mechanical properties in actual engineering, and thus its accurate values are necessary to the researches of rockburst, rock mass slope stability, rock cutting, hydraulic fracturing, tunneling, et al. Therefore, it is thus significant to evaluate and study relevant methods to obtain the reliable value."

Jan 1, 2015

By M. Jorgensen, I. Markland, D. Shuck

"The McLaughlin Mine owned by Homestake Mining Company is located 70 miles northeast of San Francisco in California's coastal range. The mine began operations in February of 1985. The mill currently processes 3,000 short-ton per day of sulfide ore that has an average grade of 0.15 ounces of gold per ton, plus another 3,000 tons per day in a newly completed oxide circuit. Annual production from the mine totals over 200,000 ounces.The sulfide ore extraction process involves three basic steps, grinding, oxidation of sulfide minerals in an autoclave, and cyanide leaching for recovery of gold in a carbon-in-pulp circuit. This process, which incorporates a new technology where oxidation of sulfide minerals is conducted prior to cyanide leaching to facilitate gold recovery, was successful from start-up. However, limitation in the grinding mills initially limited sulfide tonnage throughput.This paper discusses modifications made in the grinding circuit, both mechanical and operational, to resolve it deficiency. The SAG mill, in particular, was unable to achieve design tonnage initially and proved to be most troublesome. Complications occurred due to the hardness and variability of ore being processed, short component life, and a lifter /liner arrangement that had to be tailored to the particular circumstances at McLaughlin. IntroductionHomestake Mining Company's McLaughlin Mill, located in northern California, was designed to process a refractory gold ore at a rate of 3,000 tpd to render the ore amenable to cyanidation. Seven years transpired between discovery of the near-surface ore body in 1978 and the February, 1985 plant start-up. Development of the McLaughlin mill and open pit gold mine hinged on the use of autoclave technology to achieve design recoveries."

Jan 1, 1991

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016

By Edward S. Bell, Frank Angebrandt

"Nuclear reactors must have very large heat outputs to compete with conventional sources and the only feasible applications are in the production of electric power or large quantities of process steam. This paper considers alternative fuels for electric power generation in Canada. In a publicly owned utility, nuclear stations are economic for base-load generation for unit sizes of 500 mega• watts or larger where competitive fossil fuel costs are higher than about 30 cents per million Btu. In British Columbia, Alberta and Saskatchewan, fossil fuels will continue to be in adequate supply at costs lower than 30 cents per million Btu and thus, except for the special case of Vancouver Island, power generation in Western Canada will continue to be the hydraulic and conventional thermal type. In Eastern Canada, fossil fuel prices are likely to be higher than 30 cents per million Btu and most utilities will be able to install units of 500 mw or larger, so that nuclear power plants will provide much of the base-load generation required. Base-load generation comprises about two-thirds of the energy generated by power utilities. By 1990, the total annual electrical energy load will be over 600 billion kwh, with two-thirds of this load in Eastern Canada. Allowing for additional hydraulic resources which may be developed in Quebec, British Columbia and Manitoba, hydraulic generation is forecast to provide a little more than a third of this electrical energy, nuclear generation a third and fossil-fuelled generation about a quarter."

Jan 1, 1969

By A. I. Collins, D. Danninger

Newmont has installed advanced control and online optimization on the dry grinding circuit and both roasters on its Carlin Trend refractory ore treatment plant. Subsequently, Newmont has developed a master plan for institutionalizing advanced control and optimization on all its processing units. Newmont is committed to a program of applying advanced control and optimization from crushing of ore to pouring of gold. This paper describes Newmont's experience with implementing advanced control and optimization and the benefits received. In addition, identification of advanced control and optimization opportunities and their economic justification is discussed.

Jan 1, 2005

By W. Swidzinski

"Zelazny Most" post-flotation copper mine tailings pond is the only place to of storeing wastes for KGHM POLSKA MI EDZ S.A. The flotation tailings is are the main waste stream in copper mining in Poland. Sufficient storage capacity for tailings is crucial for , thus uninterrupted production of copper is crucially related to the possibility of storing wastes in the pond. The pond covers a Its over 14 km2 arca, almost 50 m high dams making this dame this construction one of the largest in the world. The risk assessment of potential damage due to un stable ility loss of dams or environmental contamination, as well as safely constructing damsincrease of dams within the design criteriaprocess, require quick access to a large amount of the monitoring data , which in vast amount have to be monitored, that needs to be analyzed and processed and reported, every day. This In the paper describes the numerical information system "SyZeM" , used for designated to the "Zelazny Most" pond, baseding on the Oracle database and Geographical Information System , to manage the graphical and descriptive data in coherent way., is presented. The main structure of the system, as well as the methodology of storing, processing and reporting the geological, geotechnical, hydrogeological, geophysical, chemical and survey data are shown. The aspects of Optimizing optimal and risk mitigation and safe management of copper wastes and risk mitigation with the help of "SyZeM" are discussed.

Jan 1, 2007

By L. Cheng, Y. W. Pan, Y. R. Liu

"Impounding deformation of slope and foundation is significant during and post dam construction. Reservoir impoundment is accompanied with various phenomena, including material degradation, effective stress decreasing and buoyancy in rock masses. These phenomena are related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope, which finally led to failure and landslide. Pore pressure in jointed rock masses is considered in constitutive relation. The expression of effective stress for porous rock with fluids is incorporated into the Drucker-Prager criterion. Based on monitoring data of valley width and dam deformation, the effective stress law is applied to analyse the impounding influence of slope and foundation to Jinping-I high arch dam. The dam is accompanied with complicated topographical and geological conditions. The results show that calculated and monitored values agree well, and the application of effective stress law provides an approach to evaluate dam deformation, stress and stability with impounding effect considered.INTRODUCTIONImpounding deformation of slope and foundation is a common and significant problem during dam construction and operation. This phenomenon exists in a lot of reservoirs in China, like Laxiwa, Ertan, Xiluodu and Jinping-I arch dams, and some dams in Europe. It is related with some engineering concerns like reservoir-induced earthquake, landslide and dam stability. The Malpasset dam and Vajont dam are typical hydraulic projects suffering from seepage in dam foundation and slope. Monitored data indicates that the valley width tends to shrink in hydraulic engineering during the impounding process, which will change the stress and deformation of dam and abutment. Therefore, global stability of dam and foundation should be evaluated with impounding process taken into consideration."

Jan 1, 2015

By C. P. Jenney

"Exploration for copper, in a region of 7,000 square miles on the Arctic coast between longitudes 114 and 118 degrees west, has covered a period of nearly 200 years. Occurrences of native copper, used by the natives for tools and weapons, have been reported since the early part of the eighteenth century. In J 771 Samuel Hearne of the Hudson's Bay Company, in the course of his classic 3-year journey from Fort Churchill, became the first white man to see the deposits, and incidentally the first to reach the Canadian Arctic coast by land. During the next 140 years the deposits were mentioned by every explorer and traveller who passed through the area. A good historical summary of this literature has been presented by Tyrrell (1912).In 1911-12 the Douglas-Sandberg party did the first geological mapping along the Coppermine River and Dismal Lakes (Douglas, J., 1913; Douglas, G. M., 1914), and described the copper occurrences there. In 1914 J. J. O'Neill (1924) of the Canadian Arctic Expedition investigated the showings on Bathurst Inlet. In 1929-31 two Canadian exploration companies sent prospectors and geologists to the area (Gilbert, 1931; Norrie, 1931; Duncan, 1931). Since that time only brief references have been published (Kidd, 1931; Stockwell and Kidd, 1931; Lord, 1941, 1951; Washburn, 1947). In 1943-45 an area of more than 1,500 square miles was prospected by American Metal Co. of Canada, Ltd., under the direction of the writer. Forty-nine showings were examined; seven of these were mapped in detail by plane-table and two were sampled by 27 short diamond drill holes totalling 3,061 feet. All holes were in permanently frozen rock, and the deepest vertical distance reached was 206 feet. Five groups of claims were staked. These later lapsed, but one of the groups was restaked in 1951, and assessment drilling and some trenching were carried out in 1952-53. Results were disappointing, and the claims have been allowed to lapse.The area is within the Arctic Circle, northeast of Great Bear Lake and 360 miles north of Yellowknife on Great Slave Lake. For exploration purposes, access is by aircraft from Yellowknife. During the short open season heavy freight can be brought by sea to Coppermine at the mouth of the river, either from Aklavik at the mouth of the Mackenzie or around Alaska. Concentrates would have to be moved by these routes.Although none of the deposits so far found is mineable under present conditions, the total volume of copper in the numerous showings marks the district as a major area of copper mineralization, which may some day be of economic importance."

Jan 1, 1949

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

The Beloziminskoe deposit in Siberia is a large, potentially productive deposit of rare metals contained in ochreous apatite pyrochlore ores formed by weathering of a carbonatite. The ores are composed of pyrochlore, columbitized pyrochlore, monazite, apatite, magnetite, ferric and manganese hydroxide, titanic iron ore, zircon, hydromica, quartz, feldspar, and carbonates. A gravity-flotation enrichment flowsheet with application of cationic and anionic collectors has been developed. This flowsheet allows for obtaining a pyrochlore concentrate containing 44.3% Nb2O5 and 1.89% P2O5 with recovery of 55.83% Nb2O5 as well as an apatite concentrate containing 39.2% P2O5 and 1.05% TR2O3 with recovery of 62% P2O5 and 43.23% TR2O3 from ores containing 0.92% Nb2O5, 16.9% P2O5 and 0.6% TR2O3. Rare-earth concentrate containing 40% TR2O3 with recovery of approximately 10% TR2O3 was obtained at the same time. Major losses of valuable elements are related to slimes, which make up more than 50% of the ground ore. The niobium concentrate does not meet the phosphorus and radionuclide concentrations needed for the production of ferro-niobium. Acid leaching and sulfatization provided a high level of phosphorous and radionuclide removal. Conditions include hydrochloric acid pre-leaching at 75- 80°C with an 18% HCl solution for four hours and low-temperature sulfatization of acid-leached concentrate at 160-180°C for one hour followed by water leaching of the residue. The apatite concentrate could potentially be processed using nitric acid leaching. This technology is based on decomposition of apatite concentrate with 55-57% strength nitric acid with transfer of rare-earth metals into solution in the form of ammonium phosphate. This technology recovers a rare-earth concentrate containing 95% TR2O3 with extraction of 86%, and highly concentrated polynutrient fertilizer (ammophos) with phosphorus extraction of 95%. The completed research shows how complex multicomponent ores of residual soil may be processed for the extraction of niobium, phosphorus, and rare-earth products.

Jan 1, 2016

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By X. Cao, J. J. Jonas, Wanjara. P., J. Gholipour, E. Dalgaard

The linear friction welding (LFW) behaviour of near-ß titanium alloy Ti-5Al-5V-5Mo-3Cr (Ti- 5553) was investigated. Microhardness measurements were performed in order to evaluate the mechanical properties of the welded material. The linear friction welded (LFWed) Ti-5553 was examined with optical microscopy and scanning electron microscopy (SEM) to evaluate the microstructure’s response to the thermomechanical conditions. Characterization of the welds included analysis of the microstructural features of the weld region and thermomechanically affected zone (TMAZ) in relation to the parent material.

Jan 1, 2010

By Glen Robertson, Jeff McLaughlin

"The Clarabelle Mill rock tailings have the potential to generate sulphuric acid through chemical and biological oxidation of sulphide minerals. Current rock tailings assay between 0.80 -1.40 %S, with sulphur occurring principally as coarse pyrrhotite. Acid generation within the tailings area can be substantially reduced by segregating pyrrhotite rich tailings in a submerged storage area and by depositing only low sulphur rock tailings in exposed areas. Laboratory tests confirmed that low sulphur tailings could be produced by flotation at reduced pH with a small xanthate addition. A plant test was conducted to evaluate the production of low sulphur tailings in conjunction with INCO's continuing commitment to environmental protection and progressive decommissioning of the metallurgical site.During the plant evaluation, approximately 5% of the mill rock tailings were reprocessed in a line of 100 tt3 Denver flotation cells. Tailing grades below 0.40% S were easily achieved through operation at pH 6 -7, with xanthate addition (dosages up to 0.02 lb/ton) and 10 -15 minutes of nominal retention time. Froth depths between 1 -3 inches combined with relatively liberal amounts of frother were required to pull the lightly mineralized froth into the concentrate which averaged 11% sulphur and less than 5% mass recovery. In addition, three field lysimeters were each filled with two hundred.ton bulk samples of low sulphur tails (0.35% S), standard rock tailings (0.98% S), and mill total tailings (2.30% S) for long term monitoring. The implications for full scale plant design, tailings area decommissioning, the possibility of increased nickel recovery and preliminary field lysimeter data are discussed."

Jan 1, 1994

By Gurinder Kaur

Selenium (Se) based materials find wide applications in rectifiers, solar cells, photographic exposure meters, data storage devices, xerography and anticancer agents. They are also used in the glass industry to eliminate bubbles and remove undesirable tints produced by iron. In addition, Se is highly reactive towards a wealth of chemicals that can be potentially exploited to convert Se into other functional materials such as CdSe, ZnSe, Ag2Se. Here, we report a review of structural investigations of Se based materials in glassy and nanostructured forms. Glasses having varying amounts of Se and Tellurium (Te) were doped with group IV and V elements such as antimony and tin. Structural changes accompanying the composition variation were characterized with x-ray photoelectron spectroscopy, differential scanning calorimetry and x-ray absorption near edge spectroscopy. At the same time Se-Te nanoalloys were synthesized in aqueous micellar phase using Na2SeO3/Na2TeO3 as the Se/Te source. Morphology change from nanoparticles to nanoribbons was investigated using Scanning and Transmission Electron Microscopy (SEM/TEM) techniques. Structural investigations were also done for well defined morphologies of Se based nano-biomaterials obtained in the presence of water soluble protein bovine serum albumin (BSA).

Aug 1, 2013

By P. Leo

The hot deformation behavior of a Mg-9A1-1Zn alloy produced by high pressure die casting has been investigated by means of compression tests in the temperature and strain rate ranges of 125-300°C and 10-5-10-1 s-1 and torsion tests over 150-450°C and 5, 0.5, 0.05 5-1 . The compression samples were deformed in the die-cast state or after homogenization at 415°C for 2 h to evaluate improvements. A premature fracture at 45° with respect to the compression axis was observed in samples strained at low temperatures and high strain rates. The torsion specimens were tested as received or after a predeformation-homogenization treatment. In addition to constitutive analyses suitable for modeling previously published, the results are fitted to a relationship between strain rate normalized by diffusion coefficient and flow stress normalized by modulus. The results fit well with a set of published creep experiments that were conducted in the range of 70-150°C.

Jan 1, 2006

By M. Seyed Ahmadi

This study investigates the role of nitrogen gas injection in the dissolution rate of Si into liquid Al. A unique revolving liquid metal tank was used, with a capacity of 50 kg of liquid Al. Experiments without gas injection have shown that the dissolution of Si increases as the bath superheat and the tangential velocity of the liquid Al increase. When injecting nitrogen gas at flow rates between 0-5 lit/min in the vicinity of the solid Si, results so far clearly show greater dissolution. In addition, results on the role of the gas flow rate relative to the position of the nozzle are presented and analyzed.

Jan 1, 2011