Search Documents

By Michael S. Moats, Shijie Wang, Timothy Robinson

In 1987, John Schloen published a survey and analysis of copper electrorefining tank room data. Following this paper, a series of copper electrorefining surveys have been conducted and presented at each of the Copper-Cobre meetings over the past 20+ years (1991, 1995, 1999, 2003, 2007, 2010 and 2013). For each of these surveys, William Davenport has been key driving force in the collection and analysis of data. To honour Professor Davenport’s contribution to copper processing, a review of the data was conducted. Historic trends and possible future technologies are discussed.

Jan 1, 2014

By Y. H. Hatzor, D. Bakun Mazor

"A new model for thermally-induced block displacement in discontinuous rock slopes is being explored inside a Controlled Climate Laboratory (CCL). The model is based on a hypothesized wedging mechanism that takes place inside the filled tension crack of a discrete block that rests on an inclined plane. Irreversible block sliding is assumed to develop in response to climatic thermal fluctuations and consequent contraction and expansion of the sliding block material. While an analytical expression for this model is already available, we are exploring the possibility of obtaining such a permanent, thermallyinduced, rock block displacement, under fully controlled conditions in the laboratory, to enable effective analysis of the sensitivity of the mechanism to geometry, mechanical properties, and temperature fluctuations.A large scale (approximately 0.5 m3 in volume) model consisting of four blocks has been installed in the CCL. The CCL permits accurate control of atmospheric temperature (?0.5 °C) from 6 °C to 45 °C. Harmonic temperature function is planned in advance and is controlled by a computer program throughout the experiment process. The minimum length of the temperature cyclic period for thermally-induced block displacement is calculated here based on the existing analytical model.Due to the fact that this experiment is still in progress, preliminary results will be available in the next few months. The obtained results may explain sudden triggering of rock slope failures that are not correlated with common failure triggers such as seismic activities, pore pressure build-up, or freezing and thawing of water inside rock joints."

Jan 1, 2015

By Chaluvadi K. Sridhar, Prashanta K. Chatterjee

"IntroductionThe planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc., do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered.Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate man y layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment. Although recent advances in computer graphics have provided the hardware necessary for developing and evaluating min e plans rapidly, software that will allow the mining engineer to make use of the new technology is slow in developing. The need for such software packages has been recognized and ackowledged.At several sessions in recent conferences on the applications of computers in the mining industry, the use and benefit s of computer-aided mine planning were discussed. However, there were few papers presented that referred to actual applications of interactive graphics to underground mine planning. The emphasis of this study is toward the development of a completely integrated computer-aided underground mine planning package that integrates geological modeling, engineering design and planning"

Jan 1, 1986

By Scott K. Palm, Neil D. Pearson, Jr. Read

"Uncertainty is an important feature of many investments, but it is especially important for mineral properties. Mine properties often entail large investments and fixed commitments. Managers in the mining industry often view price uncertainty as undesirable, due to the possibility that the price of the mined commodity will fall to a level that prevents the firm from recovering its investment and fixed costs. This paper identifies pitfalls in conventional valuation methods and outlines a new approach to valuation based on option pricing theory and dynamic programming. In the process, it identifies generic strategies for organizing mine production in ways that allow the owner to benefit from the uncertainty in mineral prices. IntroductionRisk is pervasive in the mining industry. The operation and maintenance of a mine may involve high, and unavoidable, fixed costs. A mine owner can only begin to recover these fixed costs if the price of the mined commodity is greater than the incremental cost of production. But the prices of many minerals are extremely volatile. The price volatility of copper has been significantly higher than the price volatility of a typical stock, for example. A mine owner cannot be sure that the price of the mineral product will remain high long enough for the firm to recover its capital and fixed costs.Mine owners are able to minimize their losses during periods when the output price is below the incremental cost of production by temporarily closing operations. During these periods they incur only fixed costs. While shut-downs help minimize losses, the y do not help the firm recover its initial investment. If output prices remain low long enough, the fixed costs and original investment may never be recovered. High fixed costs, therefore, lead to substantial downside risk."

Jan 1, 1986

By P. G. Keohane, J. S. Drake

"Cominco's Polaris Mine is a lead-zinc underground operation that began commercial production in early 1982. The mine site is located on Little Cornwallis Island in the Canadian Arctic at a latitude of 75°23'N and at a longitude of 96°55'W. The nearest settlement, Resolute Bay, some 100 kilometres southeasterly from the mine, is accessed from the mine by light aircraft. The mine site can be accessed by sea during the six-week ice-free period each year. During this time all major operating supplies are brought to the mine and the lead and zinc concentrate products are shipped out to market.GeologyThe Polaris orebody lies near the top of the Thumb Mountain Formation of Ordovician age. This formation is a relatively homogeneous section of thin to medium bedded limestones which are brecciated and dolomitized in the area around the orebody. The deposit is described as a Mississippi Valley-type orebody. Ore minerals are sphalerite and galena with the waste being predominantly dolomite with calcite and marcasite. The ore is quite porous with voids being generally filled with ice as the mineralized zone lies entirely within permafrost. Reserves consist of about twenty million tonnes of ore grading 3.8% Pb and 14.3% Zn with a further three million tonnes of inferred ore at a slightly lower grade.The orebody strikes in a north-south direction with the hangingwall dipping at about twenty degrees to the east. It is generally conformable with the stratigraphy. The footwall in the western portion of the orebody, the Panhandle, lies about 10 to 30 metres below the hangingwall. To the east the footwall drops sharply, creating an orebody height of up to 110 metres in what is referred to as the Keel Zone. The Panhandle Zone has typically 80 - 110 metres of cover above the hangingwall , About 25% of the reserves are in the Panhandle Zone, the remainder being in the Keel Zone. Figure I illustrates a plan view of the orebody relative to other surface facilities on the property and Figure 2 illustrates a simplified section through the Panhandle and Keel Zones."

Jan 1, 1985

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

"The gravimetric dust sampler is one of the tools now available to the industrial hygienists for determining the worker 's exposure to the numerous types of particulate matter that may be present in the workplace. The paper ' reviews the different sampling trains that can be used for the two major criteria for respirable dust and some of the sources of error in this dust assessment technique.IntroductionIt may be stated simply that the measurement of airborne dust in the working environment is done for one or two reasons: namely, for engineering control purposes and! or to evaluate the potential for toxicological insult arising from the inhalation of dust particles.This paper reviews the progress made in the development of dust-assessing instruments, particularly the gravimetric types designed to meet British and U.S. dust criteria , and discusses the limitations in their use for this purpose."

Jan 1, 1981

By C. W. Hancher, B. D. Patton, W. W. Pitt

"There are a number of nitrate-containing wastewater sources, as concentrated as 30 wt % NO3 and as large as 2000 m3/day, in the nuclear fuel cycle. The biological reduction of nitrate in waste water to gaseous nitrogen, accompanied by the oxidation of a nutrient carbon source to gaseous carbon dioxide, is an ecologically sound and cost-effective method of nitrate waste disposal. These nitrate-containing wastewater sources can be successfully biologically denitrified to meet discharge standards in the range of 10 to 20 g N(NO3-)/m3 by the use of a fluidized bed bioreactor. The denitrification bacteria are a mixed culture derived from garden soil; the major strain is Pseudomonas. In the fluidized-bed bioreactor, the bacteria are allowed to attach to 0.25- to 0.50-mm-diam. coal fluidization particles, which are then fluidized by the upward flow of influent wastewater. Maintaining the bacteria-to-coal weight ratio at approximately 1:10 results in a bioreactor bacteria loading of greater than 20,000 g/m3,This paper describes the results of a bio denitrification R&D program based on the use of fluidized bioreactors capable of operating at nitrate levels of up to 7000 g/m3 and achieving denitrification rates as high as 80 g N(N03-) per day per litre of empty bioreactor volume. IntroductionThe discharge of wastewater containing nitrate at concentrations greater than stipulated by the Environmental Protection Agency (EPA) creates an environmental hazard and constitutes a civil and/ or criminal legal liability.(I.2) At present, we have three options: (1) recycle and reuse of nitrate streams the total economic and technical balance should be Closely examined; (2) use of an alternative acid, which may pose an entirely different set of problems ; or (3) disposal of nonreusable nitrate sources by an environmentally acceptable procedure."

Jan 1, 1980

By J. Font

New approaches for the fire refining process of blister copper have been carried out at the Codelco Norte Smelter. These have been mainly focused on modification and improvement of the process configuration based in fluid-dynamic and metallurgical studies of the oxidation and impurity treatment stages. This paper presents the results of the laboratory simulations and industrial tests performed in the 250 t anode furnace, evaluating two different process configurations: ? Bottom Bath Agitation System in the vessel during the oxidation stage, ? Dual Flux Injection System during the impurity treatment stage. The results show the possibilities of effective removal of high content of sulfur from the melt during the oxidation stage by using the bottom bath agitation. The use of the dual injection system demonstrated the significant improvement in the removal efficiency of impurities. Cu2007

Jan 1, 2007

By Robert B. Parsons

"The pendulum in Ottawa has swung dramatically from fiscal policy to monetary policy over the last several years. International trends indicate that the pendulum has to start its swing the other way, if Canada's mining industry is to maintain its preeminent position in the global mining arena. This article, which is based on a paper presented by the author at the 37th Annual Meeting of the Newfoundland Branch of CIM, identifies these trends and how they could interact with Canadian policy.IntroductionThe title of this paper is not a very imaginative or catchy one, but it states the topic quite succinctly, if not tersely. This paper looks into a crystal ball to see what might be in store for mine financing over the balance of the current decade.In the event that the reader feels some trepidation about the prospect that such a paper could seek to be the definitive work on the subject, it should be made clear at the outset that this is not the case. The author is, after all, not an economist, a scholar, a financial analyst, or a soothsayer, but is rather a simple accountant who has been closely involved with the mining industry, and the financing thereof, for some twenty years.The paper recognizes that, while a mine may be born when production begins, the mine is conceived when exploration starts. As this act of conception is obviously an essential part of mining, the financing of exploration is also covered in this paper. To attain a focus, this paper approaches the topic of mine financing in the nineties as follows: first, the major emerging forces in the industry are identified: and, second, the implications of each of these forces on financing are considered."

Jan 1, 1991

By Godfrey W. McDonald, Dennis E. Fredrickson

"Commercial coal mining has been recorded in Nova Scotia since 1863 and during this period an estimated 60,000,000 short tons of mine discard containing 10 1030% coal has been accumulated, Approximately 70% of these dumps are in the Cape Breton region and most are owned by the Cape Breton Development Corporation (CBDC), formerly DEVCO.The explosion of oil produced energy costs which created an increase in thermal coal demand as well as the desire to rehabilitate abandoned mine dumps encouraged coal reclamation. CBDC was receptive to a proposal from the Selminco Joint Venture and encouraged the building of the Princess Recovery Plant (1980) and The Summit Plant (1982).The mine dump contains scrap, waste rocks, coal and substantial quantities of fine shale. The scrap and oversize are removed and the remaining material slurried with water to a density of 1.45. The slurry is cycloned to separate the saleable thermal coal from the rejects which are returned to designated areas of the dump for contouring and revegetation.BackgroundThe recorded coal production in Nova Scotia from 1863 to 1980 was 390,000,000 short tons. This extraction was associated with an estimated 60,000,000 short tons of discarded material. This mining discard and coal washing plant reject are located in numerous, varying sized dumps throughout the mining areas. Approximately 70% of these dumps are in the Sydney coal field region of Nova Scotia. The coal content of these dumps varies from 10 to 30% coal with an average of 18%.Energy CostsThe explosion o f energy costs in the mid-1970s greatly increased the sale price of thermal coal which made recovery of coal from some of the dumps economical. The environmental benefit of these operations will be the rehabilitation of the dumps upon cessation of the coal reclamation operation."

Jan 1, 1983

By D. A. Mackie, J. E. Rider

"Good belt conveyor design is the most often neglected detail in the engineering of a plant. This results in downtime from spills or jams and premature failure of equipment components. Careful layout and component selection will result in better operation, a cleaner plant and therefore lower maintenance costs.IntroductionDespite the availability of many excellent sources of data on conveyor design, such as the Conveyor Equipment Manufacturers' Association (CEMA) Manual, ""Belt Convyors for Bulk Materials"" , there continues to be repetitive errors made in design. Why? Certainly, there is no substitute for experience, but largely, classical errors in belt conveyor design is rather elementary and so the temptation to have the work done by relatively inexperienced designers is great. What that does is develop "" experienced"" designers who become incompetent through no fault of their own. It is hoped that this paper will supplement available design data, help those who are "" put into"" a design situation to better cope with their predicament, and ease the lives of plant maintenance personnel."

Jan 1, 1990

This paper examines the latest advances in mine hoist motor and drives systems. The technology employed for large hoists has migrated from the traditional DC technology to AC motors with cyclo convertor drives, and more recently, advances in pulse width modulation (PWM) drives have resulted in these being applied to large hoist drives. When combined with PWM drive technology, the induction motor presents the ideal solution for hoist applications This paper examines the factors in choosing a suitable PWM drive and motor for a hoist installation. Factors under consideration include: ? hoist duty cycle, ? drive rating restrictions, ? choice of power semiconductor device,, ? low speed operation, ? maintenance ? reliability The cage induction motor and synchronous motor are compared and it is shown that the induction motor is the motor of choice for large hoists.

May 1, 2010

By D. E. M. Plaumann

"The wet grinding of asbestos has attracted the attention of engineers for many years as a means of improving fibre liberation from the ore. Today, added impetus for wet grinding has resulted from a need to minimize worker exposure to asbestos dust in conventional dry mills using air, as well as a need to provide a cleaner, technically superior fibre for use by product manufacturers. However , high viscosities of asbestos slurries create transport and grinding difficulties which have been a factor impeding use of a wet grinding process.Laboratory evaluation of reagents to reduce viscosities of asbestos slurries found that one reagent, XFS-4272.00, reduced the viscosity of a 35% (by weight) slurry by 75%. The impact of XFS-4272.00 on actual grinding parameters were evaluated using a pilot plant rod mill. Slurries containing 78% solids and XFS-4272.00 were successfully milled and asbestos fibres from that milling compared favourably in liberation and relative surface area to asbestos fibres obtained from milling a 4% slurry without additives.IntroductionAlthough the use of asbestos has been declining over the last few years, the large deposits of chrysotile in eastern Canada (Quebec in particular) remain very important. Asbestos production in Canada stands ninth in volume for mineral production with over 740 000 tonnes produced in 1985. Of this quantity, 722000 tonnes were exported with a value of $446 million . Canada is second in world production of asbestos behind the U.S.S.R ."

Jan 1, 1988

By G. W. Davies

"IntroductionThe development of British Columbia's northeast coal deposits, represents the single biggest industrial undertaking in British Columbia's history.As a result of this development, several thousand jobs were created, hundreds of millions of dollars in new tax revenue and billions of dollars in new foreign exchange began flowing into Canada.The Northeast Coal Development began in 1981 with the signing of sales contracts to ship a total of 6.5 million tonnes of metallurgical and additional quantities of thermal coal annually to Japan over a 15-year period. The current long-term agreements contain provisions for extension to 20 years.The sales contracts with a group of Japanese steel mills were signed by two Vancouver-based mining companies, Quintette Coal Limited and Teck Corporation. The agreements followed years of exploration and negotiation beginning in 1968.The first shipment of coal from Quintette and Teck's Bullrnoose Mine was transported by BC Rail and Canadian National Railways to the Ridley Island coal port in the fall of 1983."

Jan 1, 1992

By Grant L. Anderson, Richard C. Rice, Richard L. Jentgen

"Data for underground mine-hoist ropes determined in the Ontario Special Rope Tests were obtained, encoded and analyzed statistically. Prior 10 refined statistical analyses, these data were subjected la characterization studies and preliminary analyses to allow trends to emerge that could be used to guide and facilitate the refined analysis. The data were characterized by determining distribution s for a wide range of variables including remaining strength, service life in terms of lime and hoisting cycles, outer-wire torsion values, elongation during tensile testing, diameter reduction, location of strength loss and the strength lasses associated with corrosion rating and lubrication rating , This paper describes the more important relationships between remaining strength (or, conversely, strength loss) as the dependent variable and some of the principal independent variables mentioned above.IntroductionBoth productivity and safety in underground mines could be improved if mine-heist rope Iife and reliability could be predicted more accurately . As a result, hoist-rope failure processes and their effects on rope life and remaining strength need to be quantified and related in such a way that improved retirement criteria can be developed. This is true whether the failure is incipient or actual or whether the failure mode is by corrosion , wear, fatigue or a combination of these factors."

Jan 1, 1984

By E. G. Parker

"Sherritt's zinc pressure leaching process converts zinc sulphide concentrates directly to zinc sulphate solutions and elemental sulphur. Thus, one pressure process step replaces both the roasting and leaching operations of the conventional roast-leach route. In addition, high single-pass extractions eliminate the need for residue treatments to recover unleached zinc. Because pressure leaching produces elemental sulphur, rather than sulphur dioxide, acid plants and smoke stacks are not required, and air pollution control and work-place hygiene are greatly improved. .In 1977, Cominco Ltd. and Sherritt Gordon Mines Limited jointly operated a three-tonne-per-day pilot plant to demonstrate pressure oxidative leaching of Sullivan zinc concentrate and the subsequent separation of elemental sulphur. The process consisted of regrinding the concentrate, continuous leaching at 150°C at elevated oxygen pressures in a four compartment autoclave and the subsequent recovery of elemental sulphur, either in the molten liquid form from a decantation autoclave or as a flotation concentrate. Of the zinc contained in the concentrate, 97% was extracted in 90 minutes, and 96% of the sulphur was converted to the elemental form.Following the successful pilot campaign, Cominco began building the world's first commercial zinc pressure leaching plant. This plant, which was in operation by late 1980, will eventually treat about 25% of Cominco's planned zinc capacity of270,000 tonnes per year.This paper describes the general process principles, the results obtained from the pilot plant and the integration of the process into Cominco's operations at Trail. The application of pressure leaching to a ""grass-roots"" plant is also discussed, and compared with conventional roast-leaching."

Jan 1, 1981

By R. M. T. Raja Ismail

Shipping and stevedoring industry is going to witness a massive increase in the amount of containers to be handled while land constraints become more critical. Offshore transfer operations hence offer a preferable solution to deal with the surge in cargos rather than to expand the port outwards. Recently, there has been increasing research interests on offshore crane automation. Suspended cargos in a ship-mounted crane system are caused to swing due to the vibratory motion of the ship induced by ocean waves, which can lead to collision between cargos and deck. Therefore, it is vital for offshore crane systems to satisfy rigorous requirements in terms of safety and efficiency. This paper presents the modelling and control development for offshore boom crane systems. A second-order sliding mode control law is proposed for trajectory tracking and sway suppression control, making use of its capability of actuator chattering alleviation while achieving high tracking performance and preserving strong robustness. The asymptotic stability of the closed-loop system is guaranteed in the Lyapunov sense. Simulation results indicate that the proposed controller can significantly reduce the effect of disturbances coming from gusty waves and other dynamic loadings.

Aug 1, 2013

By P. R. A. Andrews, R. K. Collings

"In cooperation with le Ministère de l'Énergie et des ressources, Québec, le Centre de Recherches minérales, Sainte-Foy, Québec, and various silica producers, selected deposits of Quebec silica were identified in the southern region of the province and sampled to provide material for evaluation as glass and foundry sand by CANMET. The samples included both sandstone and quartz/quartzite. Head sample analyses ranged from 94.66% to 99.54% SiO2, 0.038% to 0.230% Fe2O3, and 0.16% to 4.51% Al2O3.Impurities included pyrite, iron oxides, and iron staining on quartz grains; carbonates as calcite; and alumino-silicates as clay and/or feldspar. Processing included size reduction to grain size, about 600 µm, by jaw, roll and cone crushers, and grinding in a muller-mixer. Removal of fines was achieved by attrition scrubbing and washing. Further removal of impurities was achieved by reverse flotation of iron oxide and alumino-silicate minerals employing both anionic and cationic collectors. Flotation resulted in a substantial improvement in the quality of most sands, the quartz concentrates analyzing 99.08% to 99.80% SiO2, 0.014% to 0.048% Fe2O3, and 0.06% to 0.49% Al2O3. Removal of iron oxide minerals was also investigated using the Sala HGMS. Iron oxide analyses of the non-magnetic fractions were comparable to the iron oxide analyses of the quartz concentrates obtained by flotation, 0.013% to 0.054% Fe2O3. On the basis of the samples submitted, silica from 5 of the 6 deposits studied has potential as source material for glass sand. Foundry tests showed that 3 of the 4 samples submitted for evaluation have potential as foundry sand."

Jan 1, 1987

By Douglas W. Reeve, Hoc Nghia Tran, David Barham

"In kraft pulp mills, the spent pulping liquor is concentrated and used as fuel in the recovery boiler. Extensive deposits are formed in the upper section of the boiler due to the very high ash content of the fuel and the volatite nature of the ash. Deposits are composed of Na2S04, Na2C03 NaCI, some potassium salts and reduced sulphur compounds. Chloride and potassium salts are enriched in the deposits compared to the smelt due to their greater volatility.Severe corrosion of the superheater tubes in a recovery boiler has been traced to three factors: a non-uniform temperature profile in the flue gas, relatively high operating steam temperatures and high chIoride and potassium concentrations in the fireside deposits.The role of chIoride and potassium in superheater corrosion has been explained by increased Iiquid phase in deposits. Together with corrosion studies, this information has shown that kraft recovery boiler superheater corrosion due to the chloride and potassium enriched deposits can be avoided by proper boiler operation and by judicious superheater and furnace design.IntroductionThis investigation of recovery boiler superheater corrosion was initiated by the discovery of severe corrosion of the final stage superheater in a Canadian closed cycle kraft pulp mill(1,2). Metal wastage leading to tube failure was believed to be due to three major causes : the relatively high operating steam temperatures, the uneven distribution of flue gas temperature across the boiler which created a "" hot spot"" and the high chloride and potassium concentrations in the superheater fire side deposit. The mill responded to the problem by i) lowering the superheater steam temperature from 475°C to 380°C, ii) minimizing the chloride content in the spent pulping liquor, by controlling the NaCI input with recovered bleach plant effluent, and iii) changing metallurgy of a portion of the bottom section of the final stage superheater platens from ferritic steel T-22 (2.25% Cr, 1% Mo) to austenitic steel Incoloy 800H (21% Cr, 32% Ni, 46% Fe, 1.5% Mn, 1% Si, 0.6% Al) (Fig. 1). Details of the superheater corrosion experienced in the closed cycle mil! have been reported in previous papers(l ·2,) ."

Jan 1, 1984