Search Documents

By Andrew J. Neale, Brian C. Flintoff

"In most mineral processing operations the term ""audit"" is usually reserved for the exercise of checking financial records and/or safety practices. While these activities are time-consuming, no one disputes their necessity or value. If these areas are subjected to such careful scrutiny, why is it that the same principles are not normally applied to critically examine process operation. After all, the operating efficiency of the plant impacts directly on the measures of profitability.A mineral processing plant is a complex system that has a number of distinct, but mutually dependent elements: process equipment, instrumentation, operating policies, maintenance policies, control strategies and people. To ensure maximum economic performance in the dynamic environment that characterizes a concentrator, requires a periodic review of each of these areas. However, to be useful, the study must be based on sound metallurgical principles and be conducted in a highly focussed manner. Experience has shown that the exercise is very revealing and rewarding.This paper will discuss the plant audit process and illustrate its potential value through examples taken from plant studies."

Jan 1, 1992

By A. Henk, C. M. Aruffo, K. Fischer

"Geomechanical reservoir modeling offers a valuable tool to predict tectonic stresses, in particular the local perturbations in orientation and/or magnitude which occur at lithological boundaries and faults. The paper presents a workflow for building and calibrating such geomechanical models. The numerical simulations are based on the Finite Element method and can range from field-scale models to smaller, highly detailed submodels of specific fault blocks. The approach considers the reservoir-specific characteristics with respect to subsurface geometry (lithostratigraphic boundaries, faults), mechanical properties and ambient stress field. During the subsequent calibration stage calculated stresses are compared to stress data actually observed in borehole data. Poorly constrained input parameters are iteratively modified within reasonable limits until a satisfactory fit between calculated and measured stresses is achieved. This validated model can then be used for stress predictions between wells and in undrilled parts of the reservoir, respectively. The workflow is applied to two case studies - a large gas field in Northern Germany and a CO2 sequestration project in Australia – to test and illustrate its practical value. INTRODUCTIONDetailed knowledge of the tectonic stress field is crucial for the optimal exploration and use not only of conventional and unconventional hydrocarbon reservoirs, but also for deep geothermal reservoirs, carbon capture and storage (CCS) projects as well as underground mining and nuclear waste repositories. Any reliable stress prediction is hindered by the observation that the magnitude and orientation of the stress field can vary significantly – not only in time, but also in space. Such spatial stress variations comprise all scales, i.e., from the scale of lithospheric plates down to the grain-scale. On the reservoir- and fault blockscale, the local stress field can be influenced by faults and different mechanical properties of lithologies (Sassi & Faure, 1997). The resulting variations in stress magnitude and/or stress orientation are commonly referred to as stress perturbations and give rise to a unique, reservoir-specific stress pattern (Yale, 2003). Thereby, local stress fields can deviate by up to 90° in orientation and several tenth of Megapascal (MPa) in magnitude from regional trends."

Jan 1, 2015

By Tommee Larochelle, Henry Kasaini

"Simulation of rare earth element solvent extraction processes for plant design and optimization is complex, requires extensive bench scale and pilot scale testing, and is traditionally performed using proprietary algorithms. The complexity of simulation is mainly due to traditional simulation software solvent extraction modules not being designed to simulate rare earth separation processes because of the interaction between each element. This paper presents an alternative method for designing and optimizing rare earth element solvent extraction separation processes using METSIM to converge each stage of the battery individually until the full battery reached ultimate convergence. A feed-forward controller is used to control the organic to aqueous flow ratio feeding the solvent extraction modules. This method minimizes the complexity of simulating such processes by using inexpensive batch solvent extraction data, and allowing for rapid theoretical optimization, by varying the process configuration and parameters from a graphic interface instead of the traditional code-based interface of most proprietary models. Comparison of the model predictions to pilot plant data reveals that the method can be used to accurately model rare earth solvent extraction processes, as illustrated by its application in the development of Rare Element Resources innovative process.INTRODUCTIONThe Rare Earth Elements (REEs) consist of 16 metals, specifically the 15 lanthanide elements and yttrium, which is typically found in the same mineral deposits as the lanthanides. Scandium can be associated with the rare earth elements, but is usually only present in trace amounts, and therefore omitted. The term “rare earths” originates from an old term used to designate minerals (earths) and their believed scarcity upon their initial discovery. The rare earths designation is now considered a misnomer because it was demonstrated that the crustal abundance of some rare earth elements, such as cerium, is known to be higher than many common metals, such as copper. However, enriched deposits are fairly uncommon compared to other similarly abundant metals. The REEs are typically divided into groups commonly consisting of light rare earths (LREEs), medium rare earths (MREE), and heavy rare earths (HREEs). Light rare earth elements include lanthanum to neodymium, medium rare earths include samarium to gadolinium and the heavy rare earth elements include terbium to lutetium, and yttrium. The REEs exhibit similar chemical characteristics and are usually extracted from the ore and processed into a mixed rare earth concentrate. The rare earth concentrate requires further processing in order to separate the REEs from each other and produce a series of single element products."

Jan 1, 2016

By Troy Boisjoli

Since its discovery in February 2014, the Arrow Uranium Deposit has undergone rapid development through aggressive and systematic drilling programs and is now being progressed through advanced engineering and permitting. Based on the 2018 NI 43-101 Technical Report, the Probable Mineral Reserve estimate totals 234.1 million (“M”) pounds (“lbs”) triuranium octoxide (“U3O8”), contained in 3.43 M tonnes at an average grade of 3.09% U3O8. The proposed processing plant at the Rook I Project (the “Project”) will be capable of producing up to 31 M lbs of U3O8 per year, with a projected mine life of nine years based on the Probable Mineral Reserve estimate, although NexGen is permitting a 24-year operating life at the Project assuming the majority of Inferred Mineral Resources are upgraded to Indicated Mineral Resources with continued mineral resource development drilling. The Project will be developed through transverse and longitudinal longhole mining methods, pairing primary and secondary stoping techniques with a high degree of equipment mechanization which will provide a combination of good productivity, high extraction, and stable back support. This next generation of uranium operations combines the use of advanced tele-remote equipment and instrumentation with a low-cost bulk mining method and a best-in-class tailings management practice, effectively reducing operating costs and setting a new standard for elite environmental and social practices.

Jan 1, 2020

An optimized long-term mine planning determines the best order of material extraction, so that the Net Present Value (NPV) becomes maximum. In the case of oil sands surface mining, one of the key constraints in NPV maximization is the volume of tailings slurry that will be generated downstream. Specifications of tailings slurry are also important from environmental perspective. Moreover, most of the material that will be used for the reclamation of tailings ponds in later periods is generated in extraction and processing of oil sands. In this paper, an integrated optimization framework is proposed to maximize the NPV of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. The proposed model is coded in Matlab and has been run using CPLEX for verification. The results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Aug 1, 2013

By M. L. Jeremic

"Hydraulic mining consists of coal erosion by powerful jet s of water from hydraulic monitors operated by remote control. The broken coal is crushed and mixed with water and then transported from the face to the surface using gravity whenever possible. This is a simple, safe and productive method. It will easily satisfy North American productivity standards if the structural features and coal properties are favourable for water jet cutting technology (Kaiser Resources Ltd. , hydraulic mine). General ConsiderationIn open-pit mines, placer mining (Fig. I) and hydroelectric construction projects, hydraulic earth moving techniques have been successfully applied. The stripping and transporting of the overburden has been accomplished by means of large monitor jets augmented by slurry pumps and pipes. An extension of this technique has led to the underground extraction of coal and ores. To date, the method has been most successfully used in undergrond coal mining, because the coal can be easily cut and flushed away by water jets, and the rocks of the roof strata can be left behind. Due to this favourable situation, the hydraulic mining definition only relates to the underground coal mines.At present, there are four basic types of hydraulic mining, which can be defined according to the coal breaking technique used in each case. The methods are briefly discussed below:(1) Coal excavation may be carried out by conventional techniques, but the mine is designed and equipped for the hydraulic transport of the mineral from the working place to surface. Under these circumstances, the coal breaking may not be influenced by the water jet, however it may be indirectly involved. For example, pre-loosening of the coal may be done by water infusion-hydraulic fracturing. Water may also be used to flush the broken coal, which has been excavated either by drilling and blasting or by mechanical cutting, into the transport flumes. In other cases, a mechanical loader may load the coal directly into the hydraulic transport system, without using any water for the extraction process. This hydraulic mining concept is primarily used for hard and impermeable coal, such as anthracite."

Jan 1, 1980

By K. E. Waters, N. Brodusch, R. Gauvin, C. Teng, H. Demers

Rare earth elements play an increasingly important role in renewable energy devices and high-end electronics. In this project, the composition and morphology of REEs-bearing minerals are characterized with a field-emission scanning electron microscope at high spatial resolution and high counts rate using an X-ray silicon drift detector system. High spatial resolution imaging and energy dispersive X-ray microanalysis were applied at low and high magnification to obtain the composition of each phase in the minerals. From the standardless quantitative analysis results, the amount of REEs in each phase was measured and the relationships between those phases were identified.

Jan 1, 2014

By G. M. Proudfoot

IN June, 1940, a .Longyear 3420 blast-hole drill rig was purchased by the Hudson Bay Mining and Smelting Company for the purpose of experimental blast-hole drilling. The early work showed that the diamond drill could compete successfully with the Leyners then in use and by January 1st, 1941, the diamond drills were placed on contract. They may be considered to have gone into production at that date. Prior to the introduction of the diamond drill, our bench drilling was clone with Ingersoll-Rand S-70 and S-83 Leyner drills. Holes up to 40 feet were drilled, using coupled 1 1/4-inch round steel. Bits with a gauge of 3 inches were used in starting these holes, with a drop of 1/8-inch gauge for each 2-foot run. The holes normally ended with 1 1/2 or 1 5/8-inch gauge, though bits down to 1 1/8 inches were available for holes longer than normal or for holes drilled in abnormally abrasive ground. This method of drilling was very satisfactory and was a distinct improvement on the three-bench method of drilling used previously (1). During 1937 and 1938, when experienced miners were available, Leyner long-hole drilling was carried on with great efficiency. However, in 1939 and 1940, labour turnover in-creased and experienced long-hole drillers became scarcer. This resulted in a marked decline in the efficiency of the drilling operations, with increased costs and less tonnage drilled per shift. EXPERIMENTAL WORK The initial diamond drilling test work was carried on with a Longyear 3420 air-driven blast-hole drill rig, drilling a 1 3/16-inch hole. Tests indicated that diamond drilling could be successfully adapted to local conditions and that overall costs compared favourably with costs obtained with the Leyner long-hole method. Leyner long holes on stope benches usually bottomed at a larger diameter than the 1 3/16 -inch diamond-drill holes. More powder could therefore be introduced into the Leyner holes than could be placed in the diamond-drill holes. To achieve the same fragmentation, additional footage was required when diamond drilling. Diamond-drill holes of larger diameter were indicated.

Jan 1, 1943

By Elisabeth Kolar, Rik Catthoor, Frederik H. Kriel, Rossen Sedev, Gareth Hatch, Army Research Laboratory, Craig Priest, Scott Middlemas

"This paper reports solvent extraction of rare earth elements (REEs) carried out using a microfluidic device and considers the REE loading limit of the organic phase under laminar flow. The microfluidic device contacts aqueous and organic phase streams for a precisely defined contact time (subsecond resolution) and then separates them for offline analysis. Experiments are reported examining the effect of contact time on extraction. We focus on three REEs: one ‘light’ (Nd), one ‘mid’ (Dy), and one ‘heavy’ (Yb) REE, which are extracted using Cyanex® 572. It appears that loading limits may be locally exceeded in the organic phase near to the liquid-liquid interface, where third phase deposits are observed. Third phase formation was also observed close to the liquid-liquid interface in two-dimensional confinement, showing similar third phase adsorption on glass plates. It is also shown that, under microfluidic flow, a typical first ‘split’ between heavy REEs and light REEs can be carried out without exceeding loading limits.INTRODUCTIONMicrofluidic solvent extraction has emerged as a useful tool for studying extraction of metals in a mineral processing context (Ciceri, Mason, Harvie, Perera, & Stevens, 2013; Ciceri, Perera, & Stevens, 2011; Kriel et al., 2015; Mason, Ciceri, Harvie, Perera, & Stevens, 2013; Priest, Zhou, Klink, Sedev, & Ralston, 2012; Priest et al., 2011). The main advantages are the extremely well-defined and tunable flow behaviour, large surface-to-volume ratios, short contact times, and minimisation of sample and reagent amounts. Two main flow configurations have been studied to date: droplet-based and co-flowing streambased extraction. In the former, droplets are formed at a microchannel junction (usually a T-junction or flow-focusing junction) and flow downstream as plugs or ‘free’ droplets. In our case, stream-based extraction, the chip is a plate (often glass) with embedded microchannels (i.e. with cross-sections of tens of micrometres) that carry the aqueous and organic phases in contact without forming droplets. Thus, these chips play the role of a mixer in a conventional mixer-settler and phase separation takes place by branching the streams or collection in a vessel at the chip outlet. Stream-based extraction requires stable streams that are usually supported by a particular channel geometry (e.g. guide structure or small ‘pillars’) or surface chemistry, and flow parallel bounded by the liquid-liquid interface(Aota, Nonaka, Hibara, & Kitamori, 2006; Hibara et al., 2005; Hibara et al., 2002). Phases are disengaged downstream at a Y-junction, which is a qualitative difference between microfluidic and bulk extractions."

Jan 1, 2016

By K. V. Konigsmann

"The mill at Mattagami Lake Mines treats 3,850 tons per day. The mill feed is a heavy sulphide ore. It is composed ofPyrite & Pyrrhotite - 40%Marmatite - 17%Chalcopyrite - 2%Magnetite - 10%Talc and other Silicates - 31%The sulphides are intimately associated with each other and often finely disseminated throughout the siliceous gangue. An abundance of middling particles exist in the circuit and a delicate balance has to be maintained between concentrate grades and metal recoveries.The metal content of the mill feed fluctuates between 0.4 to 0.7% for copper and 6 to 13% for zinc.The flow sheet of the concentrator is shown in Figure 1.Eight sample streams have been selected for on-stream analysis, namely1. Copper Concentrate 2. Copper Cln Tailings 3. Copper Tailings 4. Zinc Concentrate5. Zinc Rgh Concentrate6. Zinc Cln Tailings7. Zinc Rgh Tailings8. Flotation TailingsThe mill feed is not being analysed. Only a very coarse sample could be obtained which would be difficult to pump, and the fluctuations in the copper content are too small in absolute terms to have much of a bearing on circuit operations."

Jan 1, 1969

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

By J. -P. Tshibangu, M. Ramos da Silva, F. Descamps, C. Schroeder, J. -C. Verbrugge

"The mechanical behaviour of rock materials is largely influenced by the stress state and pore pressure; this needs to be considered in many applications, such as petroleum engineering, tunnelling or stability of underground excavations.Conventional triaxial tests (d2 = d 3) are generally used to assess the influence of confining and pore pressure. In this work, those tests are performed on a porous rock named Sorcy limestone, along with more advanced stress paths like triaxial extension (d 2 = d 1) and purely deviatoric tests with independent pore pressure control. Those tests are combined to a true triaxial study on the dry rock in order to investigate the effect of true triaxial stresses and, hence, build three-dimensional limiting envelopes accounting for the influence of pore pressure.Three-dimensional limiting envelopes of dry Sorcy limestone are built in meridian and octahedral planes. The shape of the octahedral sections changes with the mean stress from triangular to hexagonal and then quasi circular. At even higher mean stresses, the evolution continues towards a triangle with apexes oriented in the direction of triaxial extension stress states. In meridian sections, the deviatoric stress first increases with the mean stress. The transition between this deviatoric mechanism and the cap surface occurs at different mean pressures depending on the Lode angle.Terzaghi’s effective stress is found to govern the yield and plastic behaviour of saturated Sorcy limestone. Triaxial tests show that the limiting envelope does not depend on the loading path (conventional compression and purely deviatoric stress paths). In triaxial extension, the brittle-ductile transition is observed for a higher mean pressure than in triaxial compression, as previously found for true triaxial tests on the dry rock.Finally, it is shown that upon appropriate normalisation, the dry and saturated yield envelopes come very close one to each other. This suggests that only the size of the yield envelope changes between dry and saturated state (pore pressure = 5 MPa); its shape does not seem to evolve."

Jan 1, 2015

By Larry T. Yano, Gerald T. Handford

"Tailings Engineering has the responsibility for planning and coordinating tailings disposal and for ensuring the stability of the tailings dyke. The inclusion of both the planning and geotechnical functions in one team has resulted in greater efficiency in the design and planning process. Major challenges in tailings disposal facing Syncrude are in the areas of: (1) sludge disposal; (2) instrumentation and monitoring; and (3) liquefaction. Meeting these challenges will have a significant effect on the cost effectiveness and reliability of the mining operation.IntroductionThe size of the tailings disposal operation has led to the establishment of a large engineering team devoted solely to the disposal of tailings. This paper discusses: the tailings disposal operation, the role of tailings engineering, the organization, inter faces, and the present and future challenges with respect to tailings disposal."

Jan 1, 1990

By Roy EI. Durr, Glen R. Davidge

"This paper presents the results of structural analyses and full-scale destructive tests conducted on liner plate culverts. The purpose of this work was to establish a design method and evaluate the suitability of using these structures in potential roof-fall areas for a rehabilitation application in lower stress and relaxed mining environments. Field evaluation of the design is currently in progress.Theoretical ultimate resistance functions were established for two different culvert shapes and were found to be representative of their experimental behaviour. The ultimate resistance function was used to determine their plastic behaviour to a rapidly increasing deflection condition, to determine the energy absorption capacity of these structures, and to predict their response to impact loading.IntroductionThe Kidd Creek mine of Falconbridge Limited is located justnorth of Timmins, Ontario. The area under rehabilitation for which this program was developed is the 2600 level of the No. I mine. The problem of effectively securing selected drifts at the 2600 level in NO.1 mine, for access to a high-grade ore block, is key to the economics of the operation. Diamond drill test holes had indicated a loosened rock mass above the 2600 level of about 7.5 m thick in response to the extensive mining operation below this level. This level forms the arbitrary boundary between the No. I and No. 2 mines, and has extensive volumes of cemented rock fill below it and largely untouched ore above it to the 2000 level in the North orebody. The walls at that level were showing relaxed ground conditions typical of de-stress: sub-horizontal joints opening up, and peeling.Due to the ground conditions, the consequent safety risks, the high grade of the ore, the potential production delays, and the likelihood of several phases of rehabilitation, regularly used drift rehabilitation employing rock bolts, cable bolting, or shotcrete was not practical. Two options were deemed possible alternatives to suit these conditions, steel sets with blocking and lagging, and liner plate culverts with backfill. Culverts were chosen."

Jan 1, 1995

By James Tuer, John R. Goode, Jim Cambon

"Hudson Resources Inc. (Hudson) has defined a major resource of high purity anorthosite (calcium feldspar) assaying about 30% Al2O3 at the White Mountain (Naajat) deposit in Western Greenland. Extensive beneficiation and evaluation testwork has shown that the material can be simply beneficiated to produce a feed material ideal for the production of low-alkali E-glass used for making glass fibre. An offtake agreement is in place with a major US fibreglass manufacturer and, subject to the mine construction schedule, shipments are scheduled for late 2016 or early 2017. In parallel with the E-glass program, Hudson has completed an initial program of metallurgical testwork which shows that the White Mountain anorthosite can be processed by hydro- and pyro-metallurgical processes to yield either smelter-grade alumina (SGA), suitable for conversion to aluminium metal, or a high purity, chemical/specialty-grade alpha-alumina (CGA) commanding a premium price. The process includes dissolution of the anorthosite in hydrochloric acid, HCl sparging to precipitate aluminium chloride hexahydrate (ACH), recycle of the ACH filtrate to leaching with a bleed stream processed for HCl regeneration from CaCl2, and two-stage calcination of the ACH to regenerate HCl and produce SGA and/or CGA. Calcium silicate and amorphous silica are marketable by-products. This paper discusses the White Mountain anorthosite deposit; the process testwork completed to develop production processes for SGA and CGA; production plans, and indicative economics.INTRODUCTIONHudson Resources Inc. (Hudson) holds a 100% interest in the Naajat Exploitation Licence in Western Greenland that cover the White Mountain high-calcic anorthosite deposit. Anorthosite is a calcium aluminosilicate of slightly variable composition but generally containing about 30% Al2O3. The alumina content is similar to that in bauxite and anorthosite has long been studied as a feedstock for the production of alumina. Other potential uses include feedstock for the high-end fiberglass (E-glass) industry and as a filler for use in paint and plastics."

Jan 1, 2016

By George R. White

"The Phalen Colliery, the Cape Breton Development Corporation's flagship, is now producing thermal and metallurgical grade coal in Eastern Canada's Sydney Coal Field. The colliery is a drift mine operating under the waters of the Atlantic Ocean. Improved mechanization, including a 2200 tonne per hour cable conveyor, and the introduction of modern retreat longwall mining methods as part of the Phalen concept are now paying off in better productivity and low operating costs. Geological conditions within the coal field are consistent with plans for ever greater outputs in the 1990s. Although much of the current production improvement is related to uprated machine capacity and simplified mines planning there is potential for even further development in the areas of maintenance, process control and engineering. Human resource development will also be a key factor. These programs are now well under way and Phalen Colliery is poised for top results in the 1990s. Comparison of the CBDC's top producer with similar operations elsewhere in the world, quantifies that potential.IntroductionAn exciting new mining project which has recently started production on Canada's East Coast has been conceived and designed to be one of the most modern and productive coal mining operations in North America.As with all mining operations, the business is basically that of material transportation. Daily, the product is transported many kilometres from the underground face to the surface and then to washing facilities. Men, materials and equipment are transported to and from the surface and the operating faces and services, such as electrical power, ventilating air, fresh water, discharge water, communications and compressed air are supplied throughout the operation to cover operating requirements. On all accounts the operation has been designed to take advantage of the latest proven technology."

Jan 1, 1990

By H. R. Manouchehri

"It is well understood that, apart from particle hydrophobicity, the flotation process is strongly influenced by the cell hydrodynamics. Once the chemical conditions were optimized and fixed, the flotation rate is essentially determined by impeller speed and the air flow rate.The collection efficiency in flotation is a product of collision, attachment and stability/detachment efficiencies. The collision efficiency for a given particle diameter is increased by decreasing the bubble size and bubble velocity as well as increasing the power input to the cell. The attachment efficiency, however, is defined by bubble size and its velocity. The detachment/stability depends on the relative magnitudes of the attachment force between the bubble and particles and the detachment force acting on the bubble-particle aggregates. For the particles having specific contact angle, the stability decreases as the energy input increases. Therefore, there must be an optimum energy dissipation to maximize recover of defined size fraction.A comprehensive laboratory study was devoted to determine the effect of power input in recovery of finely grind Cu-Ni bearing ore. Several flotation tests were conducted to define the hydrodynamic parameters for a laboratory scale Runge cell under different impeller speeds. An increase in flotation recovery of finely ground ore was observed when the impeller speed was increased from 450 to 1,200 rpm. The experimental results have shown increasing in water recovery and improving in flotation kinetics of fines by increasing the power input to the flotation cell. Implementation of the Wark flotation model to the experimental data revealed a good correlation between the experimental data and the model. For the particles having enough hydrophobicity the flotation rate increases by increasing the impeller speed due to a higher value for collision efficiency within the cell."

Jan 1, 2016

By Alex Luyima, Michael Moats

"In the present work, the oxidation of manganous and chloride ions on a mixed metal oxide (MMO) anode from a 40 ºC electrolyte containing 160 g/L sulfuric acid (H2SO4) with various concentrations of Mn2+ and Cl- was studied using cyclic voltammetry. These results indicated that Mn2+ concentration does not affect Cl2 evolution on a non-MnO2 coated MMO anode. However once MnO2 deposits on the MMO anode, Cl2 evolution is inhibited. The effects of manganous concentration and chloride concentration on the amount of MnO2 deposited in one hour were also evaluated. Cl- concentration did not affect the amount of MnO2 generated. Increasing Mn2+ concentration resulted in an increase in the amount of MnO2 deposited.INTRODUCTIONThe electrolytic recovery of zinc (Zn) is a well-known process and is estimated to produce approximately nine million tons of Zn per year worldwide (Recendiz, Nava, Lartundo-Rojas, Almaguer, & Gonzaleza, 2009). The Zn produced by this process is of high purity and has a wide range of applications, such as galvanizing (car body parts, pipes, metal wires, etc.), sacrificial anodes in offshore industries, casting alloys, alloying of brass, primary and secondary battery industries, etc.The electrochemical production of Zn employs aluminum cathodes and lead-silver anodes (Pb- Ag) (Recendiz et al., 2009). The Zn containing mineral (ZnS) is usually associated with other elements such as Mn, Mg, Ca, Cd, Cu, Cl, Fe, F, Co, Ni, Al, As, Sb, Si, Sn, Ge, Hg etc. (Nijjer, 2000). After processing of ZnS concentrates, the electrolyte obtained still contains residual metallic and non-metal impurities. Some of these impurities can impact the corrosion rate of Pb-Ag anodes."

Jan 1, 2016

By W. Almdal

"To compete in the ever expanding global market, companies must continuously improve. Benchmarking, a tool that can help determine where the best areas for improvement are, is more than comparing measures, it is comparing how business is carried out and how decisions are made. The key to success is in integrating benchmarking results into the organization, so that those most affected by the results own them and are empowered to use them as a positive change agent. This is a necessary step to achieving substantive change to practices and achieving optimum performance improvement. IntroductionBenchmarking is a powerful tool that can assist in the continuous goal of improvement. Benchmarking is more than comparing productivity rates or unit costs, it is seeking out best practices and assimilating them into a business to provide a positive change agent.Benchmarking is a continuous process - is time consuming, labour intensive, and requires a lot of discipline. There are no easy answers and no easy solutions, just a lot of work. The results, however, are nothing short of spectacular. More and more companies are adopting benchmarking practices because it is a key tool of the learning organization and will become part of the way business is done, part of the way it is managed. Business must change to stay ahead or to get ahead and benchmarking can accelerate the process of business change. Improvements in an organization can happen faster and more effectively with a benchmarking approach."

Jan 1, 1994