Search Documents

By Brian Hall

For some years, the mining industry has been consistently delivering returns below the market average. One of the causes is a disconnect between what is perceived to drive value creation by many industry analysts and senior corporate executives, and what actually drives the intrinsic value of mining operations. The perverse effect is that strategies that should increase value are perceived to have the potential to drive share prices down, and vice versa. This paper challenges common perceptions of what drives a mining company?s value. Anecdotal evidence suggests that the key drivers of value in the market, and hence in many boardrooms, are such things as increasing the reserves and production rate, and reducing unit operating cost. However, while the quoted reserves may satisfy ore reserves reporting code requirements to be economic, this does not imply that they are optimal. Often, a proportion of the quoted reserve reduces the potential value of the operation. Metal price increases, increased production rates, and operating cost reductions are all seen as conditions or actions that can improve value, and lead to cutoff grade reductions, thereby increasing ore reserves. However, modern cutoff theory and studies conducted by the author and his colleagues show clearly that, while breakeven cutoff grades will fall in these circumstances, optimum cutoffs may be much less volatile, and may even increase. Results from case studies indicate that value is maximised by right-sizing, not maximising, the production capacities, and by optimising the cutoff strategy. Values of many existing underground mining operations can be increased significantly by a substantial cutoff grade increase. Also, an increase in downside risk, and hence reduced returns, can occur using typical life-of-mine planning strategies if prices received are lower than predicted. Since this is often the case, low industry returns may be a direct result of typical strategic mine planning processes. Relatively simple cost-effective techniques are available to provide senior decision makers with information needed to assess the tradeoffs between their many conflicting corporate goals, and the balance between risk and reward. Often this information is not being generated at all. If it is, decisions affecting the value of the company are occurring by default at relatively low levels within the hierarchy, with senior executives apparently unaware of them or their potential impact. The paper concludes that without a re-evaluation of the way mining projects are valued, to demand proven value optimisation from mining plans by boards and mining analysts, the industry will continue to deliver below average returns.

May 1, 2003

By G. W. Zhang, Changsha Research Institute of Mining and Metallurgy, X. Xiao, Y. Long, L. L. Huang

"The paper presents a scale-up and design method of vertical screw stirred mill, in which the closed circuit of mill and hydrocyclone was assumed as one factor, theoretically regardless the affects inside system of the mill and hydrocylone. The specific energy is chosen as a scale-up criterion, based on the premise that when fed the same feed material, mills of different sizes delivering the same specific energy will yield products.Batch grinding tests are conducted to determine the specific energy, and combined with industrial production data, scale-up and design of vertical screw stirred mill for industrial production are accomplished. Having developed this method for the vertical screw stirred mill used in regrinding duty of iron ore in Ma Steel, it has now been successfully applied in other installations.INTRODUCTIONThe Towermill was developed in Japan in the 1950s, by the Tower Mill Kubota Corporation, it was fine and ultra-fine grinding mill of the metallic ores and concentrates. Due to the rapid development of metal mining and useful minerals disseminated fine, fine grinding and ultrafine grinding equipment has also been more wide used in minerals processing industry. Typical fine and ultra-fine grinding mil are the Vertimill and Stirred Media Detritor (SMD) Mill of Metso, Eirich Towemill, Outotec HIGmill, FLSmidth VXPmill, Xstrata Isamill and the vertical screw stirred mill (JM) of CRIMM, etc.JM series of vertical screw stirred mill were invented by Changsha Research Institute of Mining and Metallurgy in the 1980s. Energy saving and consumption reducing have been achieved through the optimization and engineering practice. More than 500 units JM series of vertical screw stirred mill are used in the iron ore, copper ore, copper-molybdenum ore, molybdenum ore, Pb-Zn ore and Au ore."

Jan 1, 2016

By Robert B. Parsons

"Two recent decisions by the Canadian courts could reduce the taxes paid by many profitable mines in Canada. At a time when the mining sector is hurting from an ever increasing tax burden and soft prices, the results of two cases are welcome news. Mining companies are well advised to check prior years' tax returns in the context of these developments. IntroductionSince 1976, the income tax legislation has provided a reduced rate of tax for taxpayers engaged in the mining of mineral resources, through the mechanism of the ""resource allowance"". The deduction given for the resource allowance effectively reduces the federal rate of tax by one quarter on resource profits. In general terms, ""resource profits"" are defined to include a taxpayer's income from: the production and processing in Canada of ore to any stage that is not beyond the prime metal stage (or the pellet stage or its equivalent in the case of iron ore); and, royalties computed with reference to the amount of value of production from mining operations in Canada.In computing income from these sources, the taxpayer must deduct expenses that may reasonably be regarded as applicable to those sources, with the exception of expenditures for Canadian exploration and development or financing costs.As a result of the mechanics of the calculation of the resource allowance, one quickly realizes that the lower the expenses deducted from the resource profits, the higher the resource profits and consequently the higher the 25% resource allowance. The impact of the recent court cases is to narrow the range of expenses which are required to be deducted in the determination of the resource profits.The two cases are outlined below."

Jan 1, 1991

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By M. R. Henzinger, W. Schubert

"The quality of the backfill applied at a shield driven tunnel is of significant importance failure of the lining. The used material also affects the interplay between support and excavation behaviour.In this research the state of the actual bedding situation is investigated by an analytical approach, laboratory tests and numerical simulations. The numerical simulation using continuum methods have shown shortcomings. These shortcomings regarding the instability of large strain simulations restrict the possibility to reproduce the relocation of the backfilling material. The performed scaled model tests have shown that the regripping process of a double shielded tunnel boring machine affects the soil failure within the gap. With the analytical results the influence of the wall friction can be predicted. Therefore the angle of the failure surface can be determined. The results have shown that the wall friction significantly increases the failure angle. INTRODUCTIONFor tunnel boring machines (TBM) with single (SM) or double (DSM) shield, precast liningsegments are used as rock support. These segmental linings are installed within the protection of the TBM shield. In order to reduce the friction while advancing, the shield diameter is smaller than the diameter of the cutter head and therefore also smaller than the excavation boundary. The difference depends on the expected radial convergences. Since the lining segments are mounted within the shield the steering gap between the shield and the excavation boundary increases and is hereinafter called annular gap.In the process of tunneling in hard rock, the annular gap is usually filled with fine grained and closely graded gravel, termed as pea gravel. The backfilling process starts as soon as possible after the shield tail passes the lining. Due to the operational procedure within the working area of a TBM, a fully backfilled annular gap might not be established after every ring closure. This leads to an unfavorable distribution of the pea gravel leaving the segmental lining partially without bedding. Segmental linings can develop sufficient resistance only when properly bedded."

Jan 1, 2015

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer's plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982

By D. F. VanDine, H. George

"The possibility of spoil pile failure at the Kara Kara bauxite strip mine, Guyana, South America, is of major concern to the mine operators. The current mining technique requires the continuous operation of an 11 ms bucket capacity walking dragline on top of 18 metres of freshly spoiled uncompacted overburden material consisting of varying mixtures of kaolinitic clay and quartzitic sand. A field biased geotechnical study of undisturbed overburden and corresponding spoiled material has identified site-specific, non-linear correlations between vane shear strength, standard penetration resistance and spoil pile composition. Readily available geological exploration borehole logs has enabled a composite clay isopach map of the entire mining property to be drawn and critical areas to be zoned according to expected slope stability. Stability has been assessed using simple hand calculation techniques. Use of the resulting stability map provides the mine operators with a means of forecasting the need for appropriate preventative measures at varying stages of mine development, throughout the life of the mine.A similar investigation procedure could be employed at many presently operating and future strip mines.IntroductionThe Kara Kara bauxite stripe mine is located at Linden within the bauxite belt of Guyana in South America. The mining property covers a total area of 88 hectares of flat to gently sloping ground of which some forty per cent is being actively mined or being preparatorily stripped of overburden, prior to eventual mining (George and Gordon, 1979). The regional climate is tropic and humid. Temperatures vary from 16°C to 38°C and yearly rainfall averages 2600 mm, with at least 55 per cent of this precipitation occurring during the 'wet season' months of May to July and December to January."

Jan 1, 1983

By P. Latostenmaa, T. Veneranta, J. Järvi, E. J. Peuraniemi

Boliden Harjavalta has operated a copper flash smelter since 1949 thus the smelter celebrates 70th anniversary of flash smelting in 2019. This paper shortly describes the historical perspective of the smelter and gives an update of the current operational issues and process modifications made during the recent years. The plant has carried out several major investments lately providing a firm view on the future. A new landfill area for the final slag was commissioned in 2018. A modernization of the concentrate storage area, a new acid plant and a debottlenecking project of the smelting line have been recently commissioned. At the same time, the tankhouse capacity will be expanded. This paper focuses on smelter modernizations. INTRODUCTION Boliden is a metal company operating mainly in northern Europe with core competencies in the fields of exploration, mining, smelting and metal recycling. Boliden Harjavalta, located in Finland, is part of the Smelters Business area of the Boliden Group and operates a copper and nickel smelter with related sulphuric acid plant in Harjavalta, and a copper refinery in Pori. As a short historical review, Harjavalta’s history may be dated back to the year 1910 when the Outokumpu ore body in eastern Finland was discovered. By the end of 1913, a copper mine was in operation and a copper plant based on Hybinette process was ready for commissioning. Due to difficulties in metal recoveries and throughput the Hybinette process was permanently shut down in 1929, and 100% of the mining production was sold as concentrate abroad. As the mine production increased steadily, a decision of a new smelter was made in early 30’s. In 1936 Outokumpu’s copper smelter based on electric smelting was commissioned in Imatra. The smelter was dismantled and transferred to Harjavalta during the final stages of the Second World War. The copper refinery started in Pori already in 1941 and the first copper anodes were cast in Harjavalta in 1945. First sulphuric acid plant started operation in 1947. Due to the post-war shortage of electrical energy, the plant metallurgists initiated a major development work to start exploiting the latent heat of concentrates. Thus, the flash smelting method was developed in Harjavalta and commissioned in 1949. Ten years later, flash smelting was also applied for nickel concentrates. Table 1 summarizes major historical and technical milestones of Harjavalta. The history of flash smelting is described in details in another paper of this conference (Jåfs et al., 2019).

Jan 1, 2019

By Chigova. Terence

In 2008, Anglo installed the Modular IntelliMine® System at its Kleinkopje Mine (AKK). As part of this deployment, Anglo also used the Change Management Consulting Service offered by Modular to ensure a successful installation. This paper outlines the benefits that AKK has realized through the deployment of the system, including a 15% improvement in tonne/kilometers per hour (TKPH). The mine benefited from the improvements provided by the system almost immediately by utilizing change management to more effectively integrate IntelliMine technology into their processes. This case study includes details about the deployed system, the implementation of change management, and recommendations to ensure success in future projects.

May 1, 2010

By D. Raicevic

After more than 93% of the uranium is extracted from Elliot Lake uranium ores by a sulphuric acid leaching process, the leach residue (tailings) contains small amounts of uranium and radioactive isotopes, particularly radium-226, which is the most serious health hazard. Heavy metal components and pyrite are also present, along with the gangue minerals. Currently, over /000 acres of the Elliot Lake area are covered with these tailings, which contain over five million tons of pyrite. Because of constant oxidation of the pyrite by bacteria (thiobacillus) and the presence of moisture, pyrite slowly generates sulphuric acid, which steadily leaches the metal-bearing constituents from the tailings. The seepage-flows of the dissolved contaminants, although often quite low in volume, have an environmental impact on the Elliot Lake area. Although these seepages are treated and most of the contaminants removed and impounded, a small amount of the radioactive contaminants reaches Lake Huron via the Serpent River. This paper describes a flotation approach for treatment of the Elliot Lake uranium tailings to produce new, decontaminated tailings practically free of pyrite, with radium, thorium and uranium contents considerably reduced. The decontaminated tailing produced, which comprises about 75% by weight of the current uranium tailings, appears to be suitable for mine backfill. Because mine backfilling normally uses about 50% of the plant tailings, the surface storage of about half of the uranium tailings, therefore, would be eliminated by this process. Mine backfilling would also increase the mine production and thus enlarge the over-all uranium resources due to recovery of the ore from pillars. The pyrite concentrate produced from the current uranium tailings would be suitable for sulphuric acid production. The possibility of uranium recovery, and disposal of radium and thorium from the concentrates produced, is now being studied at CANMET.

Jan 1, 1979

By W. G. Davenport

Methods of extracting copper are evaluated in terms of innovations during the 1970's, and predictions to the end of this century are made. It is concluded that between one and two new smelters and refineries will be needed per year until the turn of the century, and that most of these smelters will be of the oxygen or oxygen-enriched flash furnace type. For converting, the Peirce-Smith converter will still predominate, but the Hoboken converter will play an increasingly important role. Five Japanese pollution control systems are described and it is suggested that much of this technology will be included in future smelting installations. Further growth of hydrometallurgy is predicted, especially for oxide ores, based on improved product metal quality and low plant cost. A n increased level of scrap resmelting is also expected.

Jan 1, 1980

By H. Asgari, A. G. Odeshi, J. A. Szpunar

In the current research, the role of grain size on the texture formation and mechanical behavior of rolled AZ31B Mg alloy is investigated under shock loading conditions. The grain size of the original asrolled sample was 8 µm and different grain sizes, e.g. 25 and 46 µm, were produced by heat treatments at temperatures in the range of 400-500 °C. In order to evaluate the effect of grain size on the anisotropy of mechanical behavior, the samples were cut along the rolling direction (RD), transverse direction (TD) and normal direction (ND) and tested at strain rates of 900 and 1200 s-1 using Split Hopkinson Pressure Bar. Texture measurements showed that initial texture of the samples cut from the as-rolled sheet is a weak rtype texture. However, a stronger texture was observed for samples with large grains. After shock loading, a (00.2) basal texture developed in all samples and the intensity of the basal poles was higher in samples with coarser grains. This observation is corroborated by high twinning activity and possible activation of pyramidal <c+a> slip in coarse grained samples. Besides, the strength of basal texture increased with increase in the strain rate. Furthermore, the samples with larger grain size showed lower strength and higher ductility, and this was observed for all investigated strain rates.

Jan 1, 2014

By O. S. Perry, D. F. Kidd

"BEAVERDELL IS IN the Interior Plateau of British Columbia, 25 miles east of Penticton, B.C. In 1897, small but rich silver-bearing veins were found on Wallace Mountain, 2 miles east of Beaverdell. Production from the camp, at first of a modest character, started in 1901 and has never ceased. Over 90 per cent of the values in the ores have been in silver. Remaining values present are in lead, gold, zinc, and cadmium.There have been four principal mines in the camp. A fifth is approaching production. The four mines lie within a northeasterly trending rectangle about 5,000 feet long and 2,000 feet wide, the fifth mine being at the northeast end. From southwest to northeast the mines, with their silver production to Sept. 30, l 955, are: -Wellington Mine - 1,463,948 oz.Sally Mine (includes Rob Roy claim) - 1,930,124 oz.Bell Mine - 3,460,815 oz.Lass Mine - 12,557,956 oz.Other production - 331,252 oz.Total, Beaverdell Camp - 19,744,095 oz.The camp is near the centre of an area geologically mapped in 19 l l by L. Reinecke for the Geological Survey of Canada (1). The rocks of the camp comprise:1. Beaverdell stock of porphyritic quartz monzonite;2. Westkettle batholith of quartz diorite;3. Wallace formation of tuffs and lavas.The Wallace formation borders the east edge of the camp, and has been intruded by the Westkettle batholith. The batholith is the host rock for the orebodies. The Wallace-batholith contact dips gently east. Some of the Beaverdell ores at depth, while in the batholith, are under Wallace formation mapped on the surface above.West of the camp, Reinecke mapped a stock one by one and one-half miles in size, of porphyritic quartz monzonite, which he considered much younger than the Westkettle quartz diorite (I). Recent petrographic work by White and Dolar-Mantuani (3) suggests that in the vicinity of the camp the Westkettle batholith is more quartz monzonite than quartz diorite, and little different in composition from the Beaverdell quartz monzonite. They suggest a consanguinity with the Westkettle batholith."

Jan 1, 1949

By Ken Musgrave

"A program is described that helps managers and supervisors control maintenance more effectively. Work- order generation, preventive maintenance, repair parts inventory, planning and scheduling, reporting, analyzing costs, printing purchase orders and other functions are covered. Flexibility often permits integration with other programs such as payroll, cost accounting and materials management.The Role of MaintenanceMaintenance provides a service to allow the rest of the operation to do its job effectively. Its success should not be measured by maintenance cost alone, but also by its effectiveness in reducing downtime and maximizing production. It can make sense to spend more maintenance dollars if this results in an even greater contribution from increased production.The Cost of MaintenanceIn mining companies, maintenance costs can be as much as half of operating costs. Maintenance has generally not been given the management attention that an expenditure of this magnitude deserves."

Jan 1, 1986

By L. A. Melis, A. R. Marchbank, S. A. Webster

"Certain northern Saskatchewan uranium ores have a high content of nickel and cobalt which offer the potential for recovery as a by-product to uranium. A nickel/cobalt recovery process has been developed as a viable method of recovering a marketable concentrate from typical uranium raffinate solution.Impurities are first removed from the raffinate and the pure solution is then treated with sodium carbonate to recover a bulk nickel/cobalt carbonate precipitate for sale to a primary nickel producer. All contaminants of concern are removed to very low levels and the product is free of radioactive contamination with gamma emissions significantly below natural background. Cost estimates have shown that installation of a nickel/cobalt recovery circuit within a uranium process plant is economically feasible.The testwork that led up to the selected process is described along with recommendations for further investigations such as additional testing of hydroxide precipitation as a possible viable alternative to carbonate. The selected process is described and project economics are briefly reviewed.PROCESS TEST PROGRAMBackgroundExtensive metallurgical research has been performed over the years to develop a process for recovering uranium from the Midwest deposit in northern Saskatchewan. During the course of this research, a certain amount of information became available which suggested that recovery of nickel and cobalt from uranium raffinate could be economically feasible. It was decided to undertake a test program which would investigate methods of separating nickel and cobalt from radioactive and other metal contamination to permit production of a saleable product.Available technology suggested that three general approaches could be taken to recover nickel and cobalt. The first and simplest approach would be to selectively precipitate the impurities of concern, primarily arsenic, iron and radium, and then recover a bulk concentrate from the purified raffinate. The second approach would be to purify the raffinate and then remove cobalt from solution by solvent extraction producing pure nickel and cobalt solutions for further treatment. The third approach would be to precipitate all metals from solution and then selectively re-dissolve nickel and cobalt in ammoniac solution which would be further treated by solvent extraction for nickel recovery, leaving cobalt for further treatment."

Jan 1, 1993

By Z. Zhong, Y. J. Hu, D. Elsworth

"A standard triaxial apparatus was set up to perform sliding tests. Slide-hold-slide (SHS) tests, with hold times from 10 to 3000s and at invariant effective confining pressures of 1MPa, incremented to 3MPa and then 5MPa, were conducted on both dry and wet split limestone samples to study the evolution of fracture friction under holding and sliding processes. Limestone fracture shows time-dependent behaviors in SHS tests, friction drops (creep) gradually during hold periods, and recovers (healing) after re-slide. Frictional healing and creep increment are proportional with hold times, while are inversely proportional with effective confining pressures. Moreover, the wet sample displays heavier healing than the dry one, whereas creep increment of the wet sample is lighter than the dry one. We conclude that the evolution of limestone fracture friction is significantly controlled by mechanisms of fluid-rock interactions.INTRODUCTIONThe evolution of the mechanical properties of fractures and faults exerts a critical influence on the behavior of fault zones and on the earthquake cycle. In addition to natural processes, this behavior has broad implications in induced seismicity and influences oil and gas production, the sequestration of carbon dioxide and the disposal of nuclear wastes.Fault friction is typically measured by slide-hold-slide experiments, where fault gouge is deformed at low velocities (<0.1 mms-1) and over small shear offsets (<30 mm) (Dieterich, 1979, 1981; Mair et al., 1999; Marone, 1998, 2004) or alternatively with rotary-shear devices, that enable higher slip velocities over very large shear offsets (Hirose & Shimamoto, 2005; Mizoguchi et al., 2006). Typical experiments (Dieterich, 1972; Marone, 1998; Olsen et al., 1998; Bos & Spiers, 2002; Tenthorey et al., 2003) show significant creep during the holding period and frictional healing (strength gain) upon reloading. Fault creep and healing are often time-dependent with longer hold times typically resulting in greater magnitudes of creep and in strength gains (Tenthorey et al., 2003; Yasuhara et al., 2005; Carpenter et al., 2012). Frictional healing may arise from growth of grain contacts (potentially induced by pressure solution) (Rabinowicz, 1951; Dieterich & Kilgore, 1994; Yasuhara et al., 2005), strengthening of the contacts (correlates with cementation) (Hickman & Evans, 1992; Beeler et al., 1994; Karner et al., 1997; Olsen et al., 1998; Muhuri et al., 2003; Tenthorey et al., 2003; Li et al., 2011) or via other changes in state including changes in porosity and rearrangement of force chains. Experimental evidence (Dieterich, 1979, 1981; Johnson, 1981; Marone & Scholz, 1988; Marone, 1998; Saffer & Marone, 2003; Moore & Lockner, 2007; Ikari et al., 2007; Ikari et al., 2011; Carpenter et al., 2012) quantifies both the mode and magnitude of second-order changes in the velocity-dependent (including velocity- strengthening and weakening) evolution of frictional strength."

Jan 1, 2015

By T. Robson

"A multi-seam underground mining operation employing mechanized room-and-pillar methods provides 35 per cent of Smoky River's annual ROM coal production (2 million tonnes) from the Smoky River coal field. Surface mines provide the balance. Tectonic activity, which has resulted in deformed coal seams and a rugged relief to the area, has provided natural boundaries to discrete mining areas. Coal transportation to the central preparation plant incorporates a 3 km long underground conveying system. The company is committed to efficient resource recovery and a safe and healthy working environment. Introduction The Smoky River Coal operations (SRC) are centered in the Smoky River coal field located in west central Alberta, some 360 km west of Edmonton and 20 km from the Town of Grande Cache (Fig. 1). Combined mining operations produce 2 million tonnes per year run-of-mine coal from which 1.65 million tonnes of high quality, low volatile, coking coal are obtained. The underground mining operation, employing mechanized room-and-pillar methods, provides 35 per cent of SRC's annual ROM coal production (2 million tonnes). Surface mines provide the balance. Tectonic activity has resulted in deformed coal seams and a rugged relief in the area. This has provided natural boundaries to discrete mining areas. Background Exploration of the Smoky River coal field took place over four decades commencing in 1926. McIntyre Mines Limited (parent to Smoky River Coal Ltd.}, commenced development of the property in 1968 having secured a long-term contract for the delivery of coal to Japan. Production of underground coal at Smoky River commenced toward the end of 1969 and has been continuous on the property since that time. Originally, two underground mines were opened. Original planning envisaged the use of room-and-pillar techniques to develop blocks of coal for subsequent extraction by longwall retreat mining. Following initial development, two longwall units were established, the first in November 1970 in No. 5 Mine and the second in February 1971 in No. 2 Mine. Difficulties were experienced on both units, and production commitments could not be achieved. The longwalls were discontinued, and mechanized room-and-pillar was subsequently used for all underground mining."

Jan 1, 1985

AGENDA ? Company Overview ? Industry Direction ? Technology to support maintenance ? data access, connectivity, process historian, downtime & production reporting. ? Case Studies Company Overview Corporate Offices Client Base ?16 consecutive years of growth & profitability ?#39 of Top 50 Control Companies (Worldwide) ?470 employees ?TSX: MTK Industry Direction Improved visibility into the business so they can: ? Reduce cost through better understanding of where costs are being incurred and making timely decisions. ? Optimize operations while leveraging existing assets. ? Have a single version of the ?truth? ? Deliver reliably to stakeholders on the demand for increased accountability (safety, environmental, regulatory performance etc?). ? Respond quicker to market conditions in order to out perform the competition ? Best in Class approach. Web is becoming the standard user interface.

Apr 1, 2005

By S. W. Brooksbank, R. A. Benkis

"IntroductionThe Republic of Indonesia is a developing Southeast Asian country that unites the Indian and Pacific oceans, and spreads across nearly 14000 islands with a total land area of about two million km-. The distance across the country approximates the distance across Canada: Indonesia extends for more than 6000 km from the northern tip of Sumatra to the eastern border of Irian Jaya in the middle of New Guinea. With a population of around 180million, Indonesia is one of the world&apos;s most populous countries. A mix of 366 ethnic groups populates the country and there are some 250 distinct languages spoken. The topography of Indonesia generally is quite rugged because of its numerous volcanos. For example, the island of Java has 121 volcanos, of which 15 rise above 3000 m and another 44 reach heights between 2000 m and 3000 m.Indonesia has a diversified resource base, with plentiful energy resources (coal, oil, gas and hydroelectric), significant mineral deposits, large timber potential and a developed system of agricultural commodity production and export. A high proportion of the primary resources are on the sparsely populated islands of Sumatra and Kalimantan, whereas 7&apos;3 of Indonesia&apos;s people reside on Java, or on 70/0 of the country&apos;s land area. Around Jakarta in western Java the population density is around 8000 per krn2. This contrasts with less than nine people per km- on Sulawesi (Fig. I)."

Jan 1, 1992

By E. Yalçin, A. Ünal

In transitional mineralization, the sill of the underlying variogram is relatively easily estimated, but the estimation of the nugget effect may be more difficult. This study aims to determine for massive copper deposits just how sensitive the estimations of ore reserve, economic copper content, total net value, and ultimate pit limits are to the errors of estimation in the nugget effect of the spherical variogram model. A massive copper deposit which has a log-normal distribution and a spherical variogram was simulated on a rectangular grid using the turning bands method. By using the three dimensional random kriging method, the mean block grades were estimated at four different sampling densities. The ultimate pit-limits were determined by using the two-dimensional dynamic programming algorithm. To calculate the estimation errors, the values obtained by using the actual nugget effect and structured component values were deducted from the estimations obtained using the incorrect nugget effect and structured component values. For isotropic massive copper deposits, it was found that the ratio of the nugget effect to the structured component of the spherical variogram has no significant effect on either the block grades estimated by the kriging method or on the ultimate pit limits.

Jan 1, 1992