Search Documents

By Palaniappan Chidambaram

Despite the advances in processing technologies, construction techniques, inspection methods, and materials, the number of process safety incidents are still increasing, and often the same types of incidents are being repeated. While regulators are enforcing stringent requirements in regards to safety management systems, process safety incident statistics reflect a failure in effective implementation. Upon closer look at the implementation of safety management systems, it becomes evident that the systems were not built on robust risk recognition. The risk-based implementation approach enables facilities to develop systems focused on managing specific risks and quickly gain momentum and confidence to take next steps towards implementing comprehensive systems. This paper will cover the importance of risk recognition and governance, risk based implementation and the role of Process Hazard Analysis in managing operational risks through the lifecycle.

Jan 1, 2014

By Corby G. Anderson

"Laboratory testing using industrial electrowinning solutions was performed to determine the best Faradic cell efficiency for copper cathode recovery. The variables tested were solution flow rate, recycle ratio, reagent addition combinations of guar and thiourea, and addition amount of acid mist suppressant CAL FAX DBA-70. The ideal flow rate was determined to be 37.85 litre/min. Additionally, the ideal recycle ratio was determined to be 10:1. The reagent addition scheme from testing which showed the highest efficiency was with 680 g/tonne guar of cathode copper won and with 135 g/tonne thiourea of cathode copper won. These values for reagent addition only reflect the best efficiency and should not be assumed to be the best reagent concentration for copper purity. The amount of foaming agent that showed the best efficiency was the test with 2 ppm of foaming agent. Again this amount of reagent is based on efficiency and should not be taken as the amount of reagent that does the best acid mist suppression. Additional proprietary surface characterization work indicates these additives may have enhanced the cathodic reduction surface morphology of some noble minor impurities. Subsequently, these operating parameters were introduced into the plant operation and proved successful after their implementation.BACKGROUNDCopper electrowinning has become a dominant technology for the production of marketable high grade copper cathode products. The literature is robust with applications, optimizations, additives and developments in this field (e.g., Classens & Harris, 1990; Pfalzgraff, 1999; Tozawa, Su, & Umetsu, 2003; San Martin, Otero, & Cruz, 2005; Houlachi, Edwards, & Robinson, 2007; Romero, Avila, Fester, & Yacher, 2007; Marsden, 2008; Beukes & Badenhorst, 2009; Vainio & Weatherseed 2009; Bender, 2010; Joy, Staley, Moats, Perkins, Uhrie, & Robinson, 2010; Khouraibchia & Moats, 2010; Moats, 2010; Rutledge & Anderson, 2015).Tests of forty hours duration and at room temperature were performed for this project using samples of actual industrial electrowinning solutions. These industrial solutions were comprised of 60 g/L Cu plus 65 g/L Ni, 3 g/L Fe, and 30 g/L free sulfuric acid. Other confidential minor impurities were also present including some solubilized precious metals. The testing apparatus utilizing stainless steel anodes and cathodes is illustrated in Figures 1 and 2."

Jan 1, 2016

By C. Bazin, D. Hodouin, M. Ounpuu

Sensors are now available in mineral processing circuits to monitor pulp flowrate and density, as well as ore characteristics and other process variables. The amount of information provided by these instruments is considerable but in many cases poorly exploited. This paper gives the results of the application of time series analysis techniques to signals generated by the sensors installed on an industrial Pb dezincing flotation circuit in New-Brunswick. Autocorrelation and cross correlation functions appear to be interesting tools for a preliminary circuit analysis, however the calibration of single input single output discrete transfer functions using collected sensors signals leads to conflicting results. For this reason a phenomenological approach, based on the kinetic and transport properties of the flotation process, is also considered. It has several advantages over the empirical transfer function modelling but also limitations in its applicability to industrial processes. A combination of the transfer function and kinetic modelling approches appears to be a promising avenue for better process modelling and control.

Jan 1, 1985

By Robert B. Parsons

"The Province of Manitoba tabled a Budget on March 11, 1992, which contains some important new initiatives designed to improve the fiscal environment for mining in the province. In addition, the Minister of Energy and Mines has released details of the Mineral Exploration Incentive Program which was originally announced in the 1991 Budget.Introduction""We recognize the important contribution o f mining to the economic activity of our province, including direct and service jobs and export earnings. We are determined to secure its future."" - The Honourable Clayton Manness, Minister of Finance, Province of Manitoba, March 11, 1992.With these words of introduction, Manitoba Finance Minister Clayton Manness announced a number of significant measures aimed at improving the fiscal regime for exploration and mining in Manitoba. At the same time, details of the Manitoba Mineral Exploration Incentive Program (MEIP) were released."

Jan 1, 1992

By A. E. M. Warner, A. Vahed, P. J. Mackey

In the decade 2002 to 2012 some 6.7 million tonnes of new copper concentrate production capacity was brought on line, corresponding to 2 million tonnes of contained copper. This increase in concentrate supply necessitated the commissioning of a number of new copper smelters as well as the modernization and/or expansion of existing plants to meet the demand. This paper gives an overview of the copper extractive industry, reviews recent copper production trends and changes in the copper industry, including an examination of pyrometallurgical and hydrometallurgical technology developments. WorleyParsons has supported a number of the projects involved in these developments and this role is briefly discussed. The paper introduces a number of ideas related to possible future directions of the copper industry.

Jan 1, 2014

By Carlos Antônio de Morais, Renata Dias Abreu

The present work describes a study of the separation of terbium and dysprosium from heavy RE concentrate through a solvent extraction circuit in a counter-current system. As the efficiency of the REE extraction by acid extractants rises with the increase of the atomic number of the element, the aim of this work is to extract the elements with higher atomic number maintaining Tb and Dy in the aqueous phase. Thus, terbium was separated first with subsequent separation of dysprosium. The experiments were carried out by using IONQUEST®801 as the extractant and a REE-hydrochloric liquor as feed solution. The optimum operational circuit in terbium separation was comprised of 37 stages: extraction, scrubbing, stripping, and solvent washing. For the dysprosium separation 39 stages were required. Terbium separation over 92% with over 95% purity and a Dy separation over 97% with over 95% purity were obtained.

Jan 1, 2014

By Ajit K. Sinha

"Electromagnetic surveys were conducted over the Yava sandstone-hosted lead deposit in Nova Scotia to evaluate the usefulness of such surveys for detecting and mapping sedimentaryhosted metallic ore deposits. Both transient and multifrequency systems were used for that purpose. The deposit consists of three zones of disseminated galena which also contain minor amounts of pyrite and sphalerite filling the interstices of the sandstone grains. Each zone overlies a basement depression and is separated from the adjacent zone by an intervening basement high. A conductive shale layer underlies the galena-rich sandstone formation at all three zones.Because the concentration of galena (3070 to 4% ) and other sulfides is too low to affect the resistivity of the sandstone formations for detection by ground electromagnetic (EM) methods, the strategy for our survey was to look for areas of basement depressions and the presence of conductive shale in those depressions by EM depth soundings. The presence of the galena-rich sandstone formations could be inferred because of the close association of these two features with the deposits in the Yava area. Both transient and multifrequency EM systems were successful in mapping the basement depressions and detecting conductive shale at the three known mineralized zones. The technique, therefore, seems to offer good prospects for mapping similar stratabound sedimentary-hosted sulfide deposits."

Jan 1, 1993

By C. Diaz, S. W. Marcuson, K. I. Burgess

Deep roasting in fluid bed roasters is the first unit operation in Inco&apos;s "roast-reduction smelting" process for the treatment of nickel sulphide concentrates. The roaster product, a low sulphur calcine, is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte which is then converted to low (<1%) iron matte in Peirce-Smith converters. Due to the deep roasting, a minimal amount of sulphur dioxide is evolved in the smelting and converting stages. Sulphur is eliminated from the concentrate almost exclusively in the roasters in a single, continuous, strong, gas stream suitable for treatment in an acid plant. This paper discusses the commercial scale testing of deep fluid bed roasting of nickel concentrate at Inco&apos;s Thompson Smelter as part of two commercial scale campaigns on roast reduction smelting conducted in 1981-1982. Slurry feeding, practised during the second campaign, permitted excellent control of the air/concentrate ratio in the roaster and, in turn, good control of sulphur elimination (about 80% of input). Smooth autogenous operation with high oxygen efficiencies (about 95%) was promoted by operating at bed temperatures of830°C to 850°C with calcine recycle. High throughputs and the desired metallurgy were achieved. The extensive testwork conducted during the two experimental RRS campaigns demonstrated thot deep fluid bed roasting of nickel concentrate at high oxygen efficiency is a technically viable operation.

Jan 1, 1994

By Alexander Levran

The main thrust of this presentation is to illustrate the growing contribution of solar energy to the mining industry by replacing existing mechanical and pneumatic tools and equipment with more effective and efficient electrical tools due to the increased efficiency and lower cost of solar energy generation. LCOE (levelized cost of energy/electricity) for solar energy is becoming highly competitive with other conventional sources of energy. The distributed architecture of solar power plants allows the supply of energy to highly remote and abandoned geographies. We will focus on the trend for this contribution to the mining industry over the next three years. Water desalination and delivery to the mining area will be topic of discussion regarding the contribution of solar systems in Latin America (LATAM) and other geographies. INTRODUCTION Increasing price pressure on the mining industry has generated a strong interest for mining companies to investigate energy costs and consumption. Currently, energy costs in mining economics contribute15% to 25% of the total commodity cost. In the past, most mines were operated by diesel gensets. Very high logistics costs for diesel supply, high and fluctuating diesel prices and theft led to very high energy prices. To overcome this problem, the mining industry has turned to solar energy, employing two main solutions: (i) adding a small scale (single level MWp energy supply) solar to an existing diesel system to create a hybrid solution operating as a microgrid environment; and (ii) replacing the existing diesel system with a large scale grid connected photovoltaic system financed by utilities or private IPP owners that signed a long-term power purchase agreement (“PPA”). In both applications, the near-term trend is to add storage and weather controls to optimize the electrical performance of the system. Use of concentrated solar solution (CSP) in the past was employed in a few remote sites to provide electrical energy to the mines. Currently this technology is not competitive with the photovoltaic (PV) systems. In some installations we have seen usage of a small hybrid system that is designed as relocatable, containerized and delivers scalable electrical power. In addition to the evolution of electrical energy sources, we see the trend of reduction of energy consumption in the mines by optimizing energy efficiency and generating load shifting solutions. Many studies of electrical energy in the mining industry support the growth of this trend in the mining industry.

Jan 1, 2019

By W. J. D. Stone

"INTRODUCTION Over the past decade, a number of publications have described the advances in High Intensity Wet Magnetic Separation. A number of significant, but small capacity installations were made and are successfully operating. These were followed some three years ago by larger installations treating ilmenite gravity concentrates; at least one machine treating 25 tons per hour of new feed was installed and is successfully operating.However, this still did not result in general acceptance that High Intensity Wet Magnetic Separation could be applied on a large scale. Neither did it dispel the feeling that High Intensity Wet Magnetic Separation was ""expensive"" and hence, confined to small scale – high value applications suchas the cleaning of tin concentrates. In addition, there is the usual reluctance of being the ""guinea pig"" which has resulted in waiting to see ""someone else"" make the first large installation decision. Such a decision and installation has now been made.Therefore, the purpose of this paper is to show that High Intensity Wet Magnetic Separation has been commercially accepted on a large scale and to show its general application to the base metal mineral industry.Examples are confined to a few specifics due to the large volume of preliminary test data that is available. The art has now reached the stage where much of the preliminary work should be taken through to serious evaluation."

Jan 1, 1971

By P. Condori, G. Rech, J. Winnett

"Palabora Mining Copper has a unique ore body composition which unlike other copper ore bodies has three main components in significant proportions; these are copper bearing ore, magnetite and dolerite. The high content of dolerite, a hard barren material, creates a high proportion of pebbles which normally are recycled back to the mill. This action increases the mill bearing pressure and power progressively until corrective actions are taken.A logical action to solve the pebbles generation would be to incorporate a pebble crusher. This in fact was done however two fundamental issues were encountered; the high content of magnetite and existence of a cyclone classification section. Due to the high content of magnetite, metal detectors have not been able to work efficiently to separate tramp metal which causes damage to the pebble crushers. The existence of cyclones in the circuit had a detrimental effect on the final product when the pebbles crusher was online producing coarse sandy material.Due to the difficulties in treating pebbles via conventional procedures and the unique Palabora ore composition and characteristics, sorting technology was investigated at laboratory and pilot scale. It was found that a combination of optical and electromagnetic sorting could efficiently separate dolerite from the copper bearing and magnetite ores.This paper reports the findings of the laboratory and pilot scale work performed and discusses the additional benefits to the circuit."

Jan 1, 2012

By Cheowchan Leelasukseree

Mae Moh mine, operated by Electricity Generation Authority of Thailand (EGAT), is the largest open pit mine in Southeast Asia. Its production is approximately 15 million lignite tons and 90 million m3 of waste, annually. The bottom of the final pit limit is designed to be approximately 500 m in depth. Presently, the pit depth is almost 250 m below original surface. The complexity of geological structures, such as faults, has caused a number of geotechnical difficulties. In a challenging lowwall area, called Area 4.1, an inclined weak bedding plane, G1, will be daylighted along the lowwall as following by mine plans. The dimensions of Area 4.1 are nearly 300 m wide and 90 m high. The friction and dip angles of the G1 interface are reportedly 12° and 15°, respectively. A three million m3 claystone block, resting above G1, would potentially slide down, and possibly cause a massive failure. EGAT engineers are acutely aware of the potential gigantic sliding failure and are modifying the mine plan in Area 4.1 to improve mine safety and minimize the displacement of the potential sliding block, reduce the possibility of failure and lower the additional mining cost as much as possible. The cut and fill mining technique was selected and studied to achieve those goals for mining in Area 4.1. With this mining technique, G1 will be partially daylighted. Therefore, an arch formation is induced with a sliding block above the mining area, which could perform as a temporary support undercutting a certain span. Initial studies of the behavior of the partially undercut slope are presented in this paper, along with a review of the similar failure history in Mae Moh mine and a 3-dimensional numerical model of the mine. The failure history review provides an estimation of undercut span without failure. The three-dimensional numerical model results, using 3DEC, gave an initial approximation of the displacement of the sliding block in Area 4.1. The next exciting study of the behavior of partially undercut slope is a trial undercut slope field experiment in Area 4.1. Currently, a trial undercut slope field experiment in Area 4.1 is under construction. In the field experiment, a number of monitoring programs will be installed in Area 4.1 to monitor and obtain information to allow a better understanding of the behavior.

Jun 1, 2012

By F. Pinto, C. A. Prato, R. J. Rocca, P. F. J. Huerta Soaje

"The seismic hazard for civil engineering structures is generally defined in terms of deterministic or probabilistic acceleration response spectra at an equivalent rock outcropping. The design of tunnels, however, requires the definition of demands in terms of accelerations at ground surface (near the portals) and in terms of both accelerations and velocities at different depths within the alignment. The design near the portals is controlled by inertial effects and is often times impacted by the possibility of slope instability and rockfall, whereas the design at deep sections is controlled by kinematic effects. These effects are accounted for in practice by introducing deformation patterns in the structure that are related to an assumed wavefield, often times ignoring the effect of the structural stiffness in the response. This paper presents a study regarding the definition of seismic demands for different sections of 14-km long tunnel in the Andes (Argentina-Chile), with a maximum overburden of 1750 m in a seismically active region. The tunnel will pass through volcanic massifs mainly composed by andesites and rhyolites.The study includes the definition of spectrum-compatible seismograms, deconvolution, and definition of accelerations and peak particle velocities for different overburden conditions. A kinematic interaction study for a 500-m tall ventilation chimney shaft is also described, where a simple formulation for the interaction analysis is considered in order to more accurately evaluate shear and bending demands. INTRODUCTIONThe seismic design of linear underground structures, such as shafts and tunnels, generally considers the inertial forces near the shallow sectors (e.g., portals) and the kinematically imposed deformations for the deep sections (e.g., Hashash et al. 2001). The inertial forces are often times evaluated on the basis of design spectra recommended by seismic hazard studies. The kinematic demands for the deeper sections, however, needs to be defined in terms of additional information which is not always indicated by the seismic hazard studies, e.g.; peak particle velocities and accelerations, and their variation with depth. These parameters can be determined by means of a site response analysis, whereby outcrop motions can be deconvoluted in order to evaluate motions inside the ground mass (e.g., Schnabel et al., 1972). Hashash et al. (2001) defines factors that may be used in order to account for attenuation of motions inside the ground mass. However, these factors are provided for depths up to 30 m only, whereas depths of tunnels structures can range up to thousands of meters."

Jan 1, 2015

By F. Rosenblum, P. Spira

"Self-heating of broken sulphide ore or waste rock underground can lead to ignition and cause serious problems in a mine operation. An extensive study has demonstrated that it is caused by oxidation of certain species of pyrrhotite. Self-heating was found to take place in two stages, first progressing from ambient temperature to 1000C with exothermic formation of elemental sulphur in the presence of moisture and oxygen, and proceeding to a second stage in which the sulphur oxidizes to SO2. Ignition may eventually follow. An apparatus was developed to assess the propensity of sulphide rock to self-heating and the potential for hazardous behaviour. The effect of temperature, time, rock size, and surface treatment with chemicals is presented. On the basis of these results, possible approaches for preventing a runaway reaction are suggested for further investigation.IntroductionThe oxidation of sulphide ore, waste rock or tailings backfill, which may cause hazardous conditions underground through heating, oxygen depletion and, in some cases, fire, is well documented (Farnsworth, 1977; Ninteman, 1978; Rosenblum et al., 1982; Reimers, 1987). The self-heating mechanism, nevertheless, has not been satisfactorily explained. The onset of heating from ambient temperature, in particular, has not drawn the attention of researchers. In the course of a previous study (Rosenblum et al., 1982) aimed at finding a method to assess the hazard from using sulphide tailings as backfill, the authors developed an apparatus to measure self-heating rate under controlled, near ambient conditions. This has since provided decisive information in backfill investigations in the Noranda Group.The test methodology devised for tailings failed to predict self-heating in a broken waste rock known to be active. Upon repeated testing, however, a freshly crushed sample began to exhibit appreciable heating and oxygen uptake (Fig. I). After 14 tests, the self-heating rate reached a plateau of about 4O°C/h and then fell progressively to < 5°C/h after 30 tests. It was hypothesized that weathering in the presence of moisture and oxygen during testing had caused the onset of self-heating. Active tailings, on the other hand, are exposed to natural surface oxidation and need not be weathered to show heating. Based on this finding, a new apparatus was developed capable of simultaneously weathering a sample of rock and monitoring its self-heating behaviour."

Jan 1, 1995

By T. Fliß

The protection of natural resources is of essential importance in times of rapidly increasing populations and resulting shortage of agricultural land. Soil and groundwater resources play a central role for the production of food or feed of any kind. The intensive agricultural and environmentally friendly use of these resources must ensure sufficient income and sustainability of life for future generations. Mining projects often represent a particularly deep intervention into ecosystems due to their size as well as the most expensive treatment processes. Conventional mines comprising of shafts and developed mining fields require the stockpiling of waste rock and in particular to potash mining, the discharge of brines from raw salt processing. In contrast, mining operations based on the solution mining method can be operated without major environmental impacts and lower security risks. While the solution mining for the production of rock salt finds application since more than 500 years, exist a procedure to produce potash using solution mining only since the 1980&apos;s. For solution mining drill holes are used to exploit the potash, launched from the surface into the deposit. The exploitation of the raw material occurs by the dissolution of the potash injecting solvents and creating so-called brine caverns. Currently, a number of mining projects in Carnallite deposits by the solution mining method are in progress around the world. Often these projects are located in sensitive ecosystems. K-UTEC project and support actual a solution mining operation of a Carnallite deposit for a Chinese customer in South-East Asia. This work comprises a comprehensive geological and geomechanical modeling as well as stability analyses. Furthermore the cavern design and brine field layout as well as the planning of the brine processing and the plant design. The present paper introduces this project as a case study. The application of a special solution mining procedure and processing design ensures an emission-free mining operation (Zero Disposal Plant). The emission-free operation is achieved by utilizing the full extent of the caverns to dispose the liquid solutions from processing. The presentation of principal salt processing and technical equipment will be rounded by information about the geology of the deposit. Since the deposit includes a number of sensitive minerals, such as Tachyhydrite and Bischofite the presentation comprise a lot of interesting items with special view at the brine field operation. K-UTEC designed and delivered a special blanket measuring system and a well cement according the request of the customer. K-UTEC, a research and engineering company with more than 60 years of experience in the sector of potash and rock salt mining, developed the world&apos;s first solution mining operation for Carnallite in Germany more than 30 years ago. In recent times K-UTEC served in different solution mining projects worldwide, with special view at the environmental impact, as well as the optimal utilization of the deposits.

Aug 1, 2013

By Min-Sung Kang

Excavation and earthmoving equipment mostly operate in accident-prone areas. These areas normally have rollover, confinement, and fall or may be considered harmful work areas due to demolitions and sewage removals. It is inevitable that excavation and earthmoving systems should be developed to secure the safety of operators through unmanned and remote control systems. Therefore, this research proposes a system that enables excavators to be unmanned and remote controlled without any renovation, remodeling, change, or transformation by applying attachable and separable mechanism and modules. Moreover, this research proposes the sensor module to evaluate the dynamic status without processing remodeling or transformation the existing hydraulic drive excavation system by adopting the easy attachable and separable mechanism. The study verifies this proposal based on observed possibility and feasibility through the experiments.

Aug 1, 2013

By E. L. Horner

"Srnoky River Coal is capable ofprocessing 3 million tonnes per year ofrun-of-mine coal at the Smoky River Coal preparation facilities to produce 2.1 million tonnes of high quality, low volatile coking coal for export markets. Multi-seam surface and underground mining operations are scheduled to maintain raw coal feed to the plant. Two beneficiating circuits wash the coal. A heavy medium cyclone circuit cleans the plus 0.5 mm coal and a froth flotation circuit cleans the minus 0.5 mm coal. Clean coal is thermally dried, loaded into unit trains, treated for dust suppression, and transported to west coast port facilitiesf or export. Plant by-products are used as thermal fuel Jn an adjacent power station. Quality control procedures ensure efficient resource recovery for a yield of uniform specification product, at a 7% ash level. Introduction Smoky River Coal operates surface and underground mines in the Smoky River coalfield. Approximately 3 million tonnes per year (mt/ a) of run-of-mine (ROM) coal can be processed at the coal preparation plant to provide 2.1 mt/ a of clean, high quality, low volatile bituminous coking coal. Coal is processed by heavy media and froth flotation cleaning circuits and is thermally dried.Raw Coal Characteristics The characteristics of the ROM coal, both in terms of quality and size consistency, vary with intrinsic seam qualities and mining methods employed. The two seams mined (No. 4 and No. 10) show distinctly different washability characteristics. Seam No. 4 contains relatively few middlings and can be readily cleaned by dense-medium cyclones and froth flotation to give a clean coal at specification ash content. Seam No. JO is more difficult to wash, and the ash content of the clean coal is higher than No. 4 seam at the same operating conditions. However, when the upper I m is excluded from the plant feed, the remaining lower section has washability characteristics similar to No. 4 seam. Coal mined by underground means sometimes contains caprock and consequently tends to be dirtier than similar coal mined by surface means."

Jan 1, 1985

By M. Coleman, M. E. Reed

The control of feed delivery quality to the flash furnace remains an unsolved problem. Many operations around the world still have limited control of feed quality to their flash furnace. Schenck Process and WorleyParsons continue to work towards the ‘holy grail’ of simple quality feed delivering both radial feed distribution and pulseless feed delivery. Ten years ago they joined forces to offer a system based on then Clyde Process RotoFeed system which could deliver ground level installation, online mixing of materials, pulseless feeding direct to the burner, with good radial distribution. Unfortunately, this proved to be too large a step for the Flash Smelting community and met with resistance from the process owners. Since then the community has developed a range of options some of which have been implemented over this period. Despite these improvements there are still areas of concern including safety issues associated with concentrate leaks and spills, uncontrolled variations in feed rate including massive flooding events, intermittent distribution improvement and set up of the burner continues to be trial and error and hard to repeat the success in each burner campaign. These continue to impact flash furnace performance globally on a daily basis. Following the community reticence to pursue the complete solution a number of interim steps are now available to pave the way to the ultimate feed system. The mixing of material has been installed and is delivering line blended materials on a daily basis. This paper will investigate the developments over the last 10 years and discuss the pros and cons of this incremental step process for overall furnace control. INTRODUCTION Schenck Process and WorleyParsons have continued to interact and observe changes in the flash smelting industry and to consider application of the Clyde RotoFeed now incorporated in the Schenck Process ProStreamTM range for delivery of feed directly to the concentrate or matte burner. Schenck Process pneumatic injection from the Clyde Process range, ProStreamTM, utilises two types of volumetric feeders to accurately control the feed of material into an injection pipeline. These are referred to as the RotoFeed and RotoScrew technologies and the choice of feeder type is dependent on the characteristics of the material to be handled. The RotoFeed is generally used for finer, granular and powdered materials which cannot be accurately handled with a screw such as pulverised coal and copper concentrate, whilst the RotoScrew is particularly suited to coarser lump materials, particularly abrasive of cohesive materials like zinc powder, electronic scrap and metal ashes. Both units can operate at high pressures and many systems work at 3 to 10 bar with the occasional system working at 20 or 30bar for carbon to gasifiers. For the Flash furnace the ProStreamTM units can be used to deliver each of the furnace feed materials into a single line, mixing the materials homogeneously and live to the burner.

Jan 1, 2019

By T. S. Wanne

Tunnel sealing experiment (TSX) was conducted between 1997 and 2004 in the Canadian URL located in Manitoba. In the experiment, a tunnel was excavated parallel to the maximum principal stress direction, filled with sand and sealed with bulkheads at both ends. It was then pressurized and heated by injecting hot water. The rock mass response was monitored with seismic methods. The main interest in the numerical simulation was the damage formed during the heating phase. The large-scale PFC2D models replicated a central plane- strain section of the TSX chamber. The models captured the first-order phenomena observed in-situ displaying the difference in the damage in the roof and floor regions, respectively. This difference was due to the filling material confinement of about 100 kPa on the tunnel floor, which occurred in the course of the heated experiment.

May 1, 2009

By W. F. J. Cosser

AN agreement having been arrived at in 1935 whereby McIntyre Porcupine Mines would purchase gravel for back-filling purposes from Hollinger Consolidated Gold Mines, the aerial gear as described below was installed. As originally discussed, the plan called for installation of a loading bin at the junction to the Hollinger tram, so making the McIntyre tram an entirely separate unit. The experience of the Hollinger engineers, however, went to prove that the operation of a bin (remote from sources of heat) should be avoided if possible, owing to the severe winter conditions (35° to 40° F. below zero).

Jan 1, 1938