Search Documents

By J. Smit, F. Parada, R. Parra, E. Balladares, M. P. Merino

"In this study, a two-step process was developed for recovering copper, molybdenum, zinc and iron (hematite). In the first step, grinded slags (-65 mesh) were sulphated with SO3 at 350-500ºC to form iron, copper and zinc sulphates. In the next step, the formed sulphates were decomposed to hematite, copper and zinc sulphates and oxysulphates at 700-750ºC. The generated SO3 was recirculated back to the sulphation step. The generated calcine in the decomposition step is leached with 25 gpl acid at 50ºC to dissolve the copper, zinc and molybdenum for further conventional separation and recovery. The hematite residue, of intense red color, can be used as pigment, in the ceramic industry or as pellet feed. The fine crystalline silica remains in the hematite residue."

Jan 1, 2014

By G. E. Rodger, R. Jugoon

"SUMMARYSamples of Aunor gold precipitates which varied widely in gold content were fluxed to produce a bisilicate slag with various oxidizers and combinations of oxidizers. On the basis of some preliminary tests a flux composition was chosen which appeared to show the most promise.The different components of this flux were then incorporated into a matrix for a 23 factorial design experiment to determine what were the most important variables and what changes should be made to the flux composition to optimize the resultant total bullion fineness.The results of the 23 factorial design experiment showed that the flux composition as calculated was very close to an optimum as only very minor changes were required to give bullion in excess of 995 fine.INTRODUCTIONEarly in 1969 the results from the Aunor Gold Mines refinery showed that wide variations existed both in precipitate grade and in total bullion fineness. An analysis of this data showed that as the precipitate grade increased, the gold bullion fineness also increased (see appendix 1). Therefore, to improve the refinery results test work was initiated to: 1) improve the precipitate grade and 2) to determine, with the help of statistics, a flux composition which would be able to handle wide variations in precipitate grade and give a total bullion fineness in excess of 950 fine."

Jan 1, 1970

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By Robert K. Jonas

Mining companies can improve production and reduce costs by using the best available technology to control their operations. Many mines are challenged to use multivariable predictive control due to limited experience or staffing, as well as being concerned over the robustness and sustainability of predictive controls. As a result many mines are not realizing optimal performance from their assets, and thusly are not realizing the production increases or cost reductions that this technology can deliver. Over the past few years, the application of multivariable model-based predictive control has gained acceptance in many mining processes and has proven to be robust and sustainable for some of the most challenging mining processes. New automated modeling and performance monitoring software have greatly simplified the effort to implement and maintain these solutions. In addition, many progressive companies have chosen to co-source the implementation and service of these solutions to assure project success and continued benefits stream. This technology has been successfully applied to a wide variety of processes; grinding mills, alumina digestion, CCD washer and thickeners, kilns, calciners, roasters, flash smelters, heat exchangers, evaporators, and most recently in the demanding process of flotation. This paper discusses the state-of-the art in advance control technologies in the mining industry, including the impact of these technologies on maximizing benefits, and implementing best practices for long term sustainability. Benefits from recent multivariable predictive control applications in copper mining will be reviewed, and the use of the latest predictive control technologies and practices in mining will be discussed.

Oct 1, 2009

The article presents an outline of methods and certain results of laboratory tests, underground tests and model tests, aimed at assessing performance of a powered shield support on the floor of low strength parameters. The tests were conducted within the framework of GEOSOFT project co financed by Research Fund for Coal and Steel (RFCR-CT-2010-00001). The described research works were conducted by Central Mining Institute (Glówny Instytut Górnictwa), Janina coal mine and Becker-Warkop

Aug 1, 2013

By Caitlyn J. McKinley, Ahmad Ghahreman, Maziar E. Sauber

Ever-growing global needs for critical metals, such as rare earth elements (REE), and base metals, such as copper and nickel, and their environmental impact motivated the pursuit of sustainable flowsheets. Regeneration of hydrochloric acid in chloride-based leaching flowsheets as a critical unit operation is an example of such endeavours. This study presents an efficient hydrochloric acid regeneration method from a magnesium chloride solution waste by addition of sulphuric acid in relatively low temperatures. The effects of temperature, initial magnesium chloride concentration, amount of sulphuric acid added, and airflow are examined. Experimental work are focused on temperatures between 80 and 95°C, initial magnesium chloride concentrations of 2 to 5 M, 100% to 220% stoichiometric sulphuric acid additions, and airflows between 200 to 600 mL/min. The developed technology recovers hydrochloric acid at a high rate and concentration with a relatively small environmental footprint. INTRODUCTION The mining and metals sector is under increasing environmental and economic pressure to make more efficient use of chemical reagents and energy in the production process. This affects several areas of process and flowsheet design such as the selection of the most appropriate unit operations and the overall design of the process steps paying heed to sustainability. Owing to the inherent inefficiencies of physical and chemical processes used in the mining industry, there will be materials and streams generated that are not a desirable part of the envisaged flowsheet. Thus, methods are implemented to recover and recycle such effluents. If the recovery and recycling are not economical, then procedures are followed to neutralize and dispose these effluents. In many cases, these effluents are potential contaminants or hazardous materials, and their disposal should be looked at in a much larger context. The safe management of the contaminants and hazardous effluents is a daunting problem in the mining industry and is fraught with technological, economic, social, and political challenges.

Jan 1, 2019

By S. Gößling-Reisemann

Most copper ores contain valuable co-products such as molybdenum, gold, silver, nickel, etc. Sulphuric acid and steam are valuable by-products, which are generated dur¬ing copper production. The environmental impacts from mining and refining therefore need to be shared between these by-products and co-products, an issue in Life Cycle As¬sessment (LCA) referred to as allocation. There are different, recognised methodologies for doing so: burdens can be allocated based on the market values of these commodities, they can be allocated by mass, volume, molar amount, functionality, or other physical, technical or economic factors. All of these methodologies have their respective merits and restrictions, and the choice is usually case specific. Nevertheless, the choice between alternative methodologies can have dramatic effects on the LCA results. Recycling in LCA has to be handled in a similar way, as it essentially constitutes a special case of co¬production. The existing standards (ISO 14040 ff.) allow different methods for imple¬menting recycling and allocation into metal LCAs (open loop, closed loop, value cor-rected substitution, etc.), which are still a subject of discussion in the scientific community. However, the methodology used can significantly influence the ecological profile of copper and copper products. We will present an overview of the different methodologies available for including recycling and allocation and give an analysis of how the meth¬odological choice affects the final LCA results. This work will be followed up by quantitative case studies.

Jan 1, 2007

By D Martín, G. Díaz, F. Cubeddu, A. B. Mejias

The Modified ZINCEXTM Process (MZP), developed by Técnicas Reunidas, is an industrially proven flexible process. It can handle a wide range of primary and secondary raw materials, producing SHG zinc. The core of the Modified ZINCEXTM Process is the zinc solvent extraction unit. This unit is an effective barrier for any leachable impurities present in the raw material. As a result of this an ultra-pure zinc solution is always obtained. The high versatility of the process makes the application of the technology in different scenarios possible. MZP can be effectively applied when developing a whole new plant (Skorpion) or adapting its scheme to an existing refinery (Akita), in both cases giving the same results. Flexibility in terms of capacity of the plant is a great advantage of the MZP, there is the possibility to adapt the global process to a wide range of production capacities. Zinc production capacities of over 150 000 t/a may be achieved with a single solvent extraction plant train. The robustness of the Modified ZINCEXTM Process has been recently proven on two new plants currently in operation: Portovesme (Italy) and Horsehead (USA) after start up during 2013. The status of both plants is described in this paper.

Jan 1, 2014

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate 'wetting' of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By C. B. Webber, L. S. Diaz

"The paper presents the approach taken by Craigmont Mines to grinding circuit control. A detailed description is given of a fully automatic control system which bases its control actions on the continuous measurement of particle size in the cyclone overflow stream. The control system holds a specified particle size in the cyclone overflow, and grinds rod mi 11 ore feed at increased rates. The principles of operation of the system used for continuous measurement of particle size are described, end the improvements in mill throughput and copper recovery over several months of continuous operation are presented.INTRODUCTION Craigmont Mines Limited is located in the south-western interior region of the province of British Columbia, approximately 230 road miles north-east of Vancouver, and ten miles west of the town of Merritt. A moderate climate, good roads and service facilities provided by the Canadian Pacific Railway, Inland Natural Gas Company, and the B.C. Hydro and Power Authority, have provided a very favorable mine and plant site.The preliminary metallurgical design of the Craigmont mill was based on the test results of samples obtained from the original 2500' level drift during 1959. Pilot plant runs and other research testing for design pur¬poses were conducted at the Canadian Exploration Ltd. Laboratory, at Salmo, B.C. The design flowsheet was altered in progressive stages from 2,000 to 3,000, and finally 4,000 tons per day as the ore reserves became better defined. Construction work on the 2,400' level mill site commenced in late 1960. The official opening of Craigntnt Mines Limited took place on September 15, 1961, a little over two years from the time of the metallurgical assessment of the original ore samples.Mill throughput to date has varied widely both on a daily and a monthly basis, due to the varying hardness of the mine ores. The grindability af the ore appears to be related to the oxide iron content, which varies from lows of 9% to highs of 20%. Daily tonnage has ranged from 5,000 tons per day with 10% iron in the feed, to 6,000 tons per day with 20% iron feeds."

Jan 1, 1973

? The Mining Association of British Columbia (MABC) was established through an Act of Parliament in 1901 ? The MABC represents the interests of B.C.?s ? Coal and mineral mining companies ? Smelting companies ? Advanced stage development projects ? Key areas of work: ? Environment, Health and Safety ? Policy & Government Relations ? Knowledge and Information Services

May 1, 2008

By L. Sun

In this work, strontium doped lanthanum ferrite (LSF) and their composite cathodes were fabricated by screen printing on yttria-stabilized zirconia (YSZ) electrolytes. Their electrochemical properties were evaluated by using electrochemical impedance spectroscopy and steady-state polarization methods. All the cathodes were screened by comparing their total polarization resistances before and after activation processes at different temperatures. The improved LSF composite cathodes were also screen-printed on YSZ/NiO half cells to fabricate solid oxide fuel cells (SOFCs), which have reached the output power densities of 170 mW/cm2 at 650 °C, 230 mW/cm2 at 700 °C, 304 mW/cm2 at 750 °C and 388 mW/cm2 at 800 °C.

Jan 1, 2005

By M. Isac, R. I. L. Guthrie, S. Ge

The Al-Mg-Sc-Zr alloys have shown exceptional potential as structural materials for transportation applications. These alloys have proved to be good candidates to be processed as thin strips via the Horizontal Single Belt Casting (HSBC) process. The HSBC process is a near-net-shape casting technology, which involves casting molten metal directly into thin strips, close to the final product thickness, at high cooling rates. It offers an efficient, economical and environmentally-friendly approach to the production of metal strips. Fluid mechanics and associated heat transfer are important aspects of any casting process, and the novel HSBC process is no exception. Three dimensional Computational Fluid Dynamics (CFD) simulations using ANSYS FLUENT 14.5 were performed, in order to assess the importance and effects of the various operational conditions of the HSBC process. This enabled process parameter optimization. Numerical predictions were validated against experimental casting results.

Jan 1, 2014

The North Saskatchewan River flows southwest to northeast through a 22-km-long valley in the City of Edmonton, supplying the drinking water to dozens of downstream communities. During heavy rains, combined sewers occasionally overflow into the river, which has a significant negative impact on the water quality and the sensitive environment. The West Edmonton Sanitary Sewer (WESS) W12, a syphon connecting the Rat Creek Trunk to the Gold Bar Wastewater Treatment Plant across the river, was designed and constructed to take the overflow to the wastewater treatment plant. Due to the complexity of the project, various 3D technologies were applied to facilitate decision-making processes. 3D models were developed for design review and design conflict detection, while 4D models were established to help create a robust construction schedule. Construction sequencing animation was used to convey design intents and demonstrate construction stages to contractors and workers. The combined applications of 3D technologies helped the project team to identify critical issues, and assured effective communication among engineers, management, contractors, and other parties. Therefore, it provided more opportunities for the success of the project.

Aug 1, 2013

The PEMAC Commitment to World Class Industry in Canada The Plant Engineering and Maintenance Association of Canada PEMAC is a national, not-for-profit industry and technical association for plant and facility maintenance, engineering and physical asset management practitioners and professionals. Founded mid 80?s in the last century PEMAC is a knowledge based organization that focuses on sharing knowledge with our members and the profession. We provide education and professional development programs and certification for maintenance practitioners and professionals. We develop, produce and participate in conferences, seminars and trade shows.

May 1, 2008

By J. Seidel

In 2009 Newmont Mining Corporation’s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Thorium is frequently the main radioactive element in rare earth ores and is a resource that can potentially substitute for uranium. Thorium must be separated from rare earths in order to obtain products with low radioactivity. There are abundant resources of thorium in the rare earth ores in China, especially in Baiyunebo mixed ores. As an associated element coexisting in rare earth ores, thorium is, or can be, separated from rare earth concentrate, iron concentrate, as well as from waste water and slag to achieve recovery of thorium. The methods of separation include ion exchange resin, liquid-liquid extraction, and liquid-solid extraction. TBP extraction has been the main method applied to separate thorium by domestic and foreign scholars. This paper presents a comparison of different processes for the separation of thorium from rare earth ores, especially Baiyunebo mixed ores, single bastnaesite and monazite ore, and provides suggestions for the future recovery of thorium resources.

Jan 1, 2014

By L. Hacini, N. Van L ê, P. Bacher, D. Thibault

Manufacturer welded components may suffer from high level of residual stresses which can cause premature cracking and decrease the life of the components if they reach values close to the yield strength of the material. In the present work, a robotized hammer peening technique is simulated by an impact machine and the residual stresses generated by the indentation are measured. To better understand phenomena behind residual stresses relaxation by hammer peening, the impact energy level was changed. 304L steel plates were hammer peened with 10 impacts. The contact between the hammer and sample surface was always at the same location. The strains on the surface close to the impact location were recorded during the test using strain gauges to follow residual stresses variations. At the end of the test residual stresses were measured indepth using hole drilling technique at 8mm from the impact center. The micro-hardness was monitored to evaluate the affected zone by the hammer peening. This approach gave a good estimation of the energy and number of blows to be used for efficient relaxation of the manufactured parts.

Jan 1, 2006

By J. D. Stinnette

Traditionally, airflow requirements for diesel equipment operating in underground environments such as mines and tunnels were determined by multiplying the vehicle power by a ventilation rate that was either mandated by regulations(s) or determined empirically from known quantities. In some cases, utilization factors were further used to adjust (reduce) the total airflow calculations for a diesel equipment fleet. However, in light of the drastic reductions to diesel equipment emissions mandated by the US EPA Tier IV and EURO Stage 4 regulations, there is currently a great deal of uncertainty in the underground mining industry among those responsible for the ventilation of planned new mines or the expansion of current mines. Tier IV engine standards mandate a reduction of DPM and NOx of approximately 95%, but can ventilation rates at mines with Tier IV equipment (or equivalent) really be reduced by a factor of twenty? This paper outlines some of the factors that affect the airflow required for the ventilation of modern diesel-powered equipment and examines how they can be applied in determining a reasonable ventilation rate for Tier IV compliant equipment operating in subterranean environments.

Aug 1, 2013

By R. C. Urquhart

Since the first use of the electric arc furnace Henri Moissan (1892) and its use by Paul Hérholdt (1902) to melt steel, it has been successfully used as a pyrometallurgical smelting tool in the production of calcium carbide, iron, ferrous and non-ferrous alloys. Commercial forms of the electric arc furnace have evolved from round, single-phase single electrode units to rectangular three electrode three-phase units to round three electrode three phase units and ultimately to rectangular six electrode three-phase units. DC electrical supply has also been used to replace the three phase power supplies in some cases. This paper examines how these electric arc smelting furnaces have evolved in size, efficiency and configuration within the constraints of the smelting process, electrodes and electrical power supply equipment.

Jan 1, 2014