Search Documents

By M. McKim

"Due to the fact that there were no formal papers submitted for this session we can only print the discussions of the papers. a) Maqnetic Mill Liners : M. MckimE. MarcotteFalconbridge LimitedReplyIn looking at the slides on magnetic mill liners a question comes to mind, particularly in the case of a large diameter mill using large grinding media, concerning the potential hazzards which may exist from large chuncks of steel hanging in the mill. Would you comment.The magnetism was sufficiently strong from liner to liner to hold ........................ .(We are sorry but we could not transcribe the full reply to this question as no microphone was used by the speaker and i't was impossible for us to complete the rest).·"

Jan 1, 1984

By O. Kangal, G. Önal, G. Bulut, A. Gül

The recovery of copper and cobalt from the ancient copper slags, located in Küre-Turkey, is investigated. Fayalitic type of ancient copper slags containing 1.41% Cu, 0.53% Co and 53.16% Fe were subject to the experimental study. Magnetic separation, gravity concentration and flotation test were conducted. The results of magnetic separation and gravity concentration were not satisfactory. However, a concentrate containing 9.57% Cu could be produced with 44.7% recovery by flotation. Copper and cobalt that remained in the flotation tailings was recovered by roasting with sulfuric acid followed by hot water leaching. Complete cobalt dissolution was observed in 1 hour of roasting at 150°C and 3:1 acid/slag ratio, whereas the copper recovery was 83%.

Jan 1, 2004

By S. -H. Sohn, M. -K. Cho, G. -G. Hong

In order to evaluate the properties of coating materials for BOF, the effects of dolomites (dolomite and light burned dolomite) addition on durability of coating materials were investigated. In all coating materials, matrix was dicalcium ferrite(C2F) and both free MgO and dicalcium silicate(C2S) were precipitated. Fe203 content must be controlled to improve the adhesion and durability of coating materials for BOF during oxygen blowing process. The amount of dolomites added to BOF slag must be controlled in optimum condition with high refractoriness of C2S to improve the adhesion of coating materials for BOF. The weight ratio of converter slag to dolomite must be below 8 to improve the adhesion and durability of coating materials simultaneously.

Jan 1, 2004

By Bennett McLaughlin

The Penna Shaft is the deepest single?lift shaft in North America. AGNICO-EAGLE started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1 800 tonnes per day from a 2 240-metre deep shaft. Exploration success at depth lead to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7 000 tonnes per day. The use of another double drum hoist, instead of a Blair Multi-Rope winder, to hoist 24,5-tonne skips was only made possible by lowering the safety factor. This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of three kilometres.

May 1, 2003

By Gordon Nelson

The Homestake gold mine is one of the largest and oldest continuously operating gold mines in orth Ame rica. To date this mine has produced in excess of 128.000.000 tons of ore containing almost 34 million ounces of gold . Gold mine ralization is restricted to the Homestake Formation. This unit is a metamorphosed iron-formation which is enclosed by pellitic metasedime nts below (Poorman Formation) and a pellitic to qua rt zitic unit (Elli son Formation) above. The e ntire Precambrian sequence. in the Lead area. has been subjected to a multi-stage defo rmation episode which ha c reated an extremely complex structural setting for the Homestake orebodies. Metamorphic grade inc reases from greenschi st ro amphibolite in a northeast d irecti on acros the mine area. Present thickness of the Home take fo rmation va ric from O to »400 fee t. The amount of thicke ning and th inning which is attributable to tectonic deformation or original sedimenta ry di fferences is not known. Orebodies constitute onl y a small pe rcentage of the Homestake Formation and do not occur along a pa rticul ar stratigraphic pos ition within the unit. Gold i assoc iated with inc reased py rrhotite and a rsenopyrite concentrations within the iron formation. Inc reased \ cin qua rt z development and chl oritic alteration usuall y accompany this minerali zation. Local remobilizati on of mine ralization due to metamorphi sm has occurred. Homestake mine ralization has been shown to be of sy ngeneti c origin . Because no feeder zones have yet been recognized a di stal source for the mine ralization is inferred .

Jan 1, 1986

By M. D. Quinn

THE sand and gravel used for backfilling at the Hollinger mine is obtained from deposits in a low range of hills some three miles north of the mine, where the Company owns a number of claims. The material is transported to the mine by aerial tram. Shipments from these deposits to the Hollinger mine commenced in June, 1927, and since May, 1936, sand has been supplied also to the McIntyre mine. During 1942, Hollinger requirements were 1,700 tons per day, and 900 tons per day was delivered to McIntyre. For the past seven years production has averaged 900,000 tons annually, and total deliveries to the end of 1942 were 13,129,022 tons, of which 11,075,339 tons went to Hollinger and 2,053,683 tons to McIntyre. Some years ago, when the original pit was approaching exhaustion, new workings were opened on claims east and south of the tramway terminal. It soon became apparent that the sand varies considerably in character from place to place. The weight per cubic foot was found to range from 85 to 130 lb., and the water percolation rate from 2 to 50 inches per hour. As the mine requirement is a sand with percolation rate of 6 inches or better per hour, it was evident that in certain parts of the deposits the material was not suitable for use as backfill. As a consequence, it was decided to carry out a programme of systematic sampling of the claims in order to select the areas containing suitable material for back-fill and at the same time estimate the tonnage available.

Jan 1, 1944

By S. Afshar, E. Dajoux, C. Allaire

For various reasons, molten salts, mainly chlorides and fluorides, are used in the aluminum industry. In the holding and melting furnaces, these salts may have different roles such as protecting the metal from oxidation, reducing the metal content of the skim or removing inclusions or impurities from the metal bath. However, the use of these salts may also have some undesirable effects such as easy attack of the furnace lining refractory materials by molten aluminum. The aim of the present investigation was to clarify and to compare the effects of chloride versus fluoride salts, on the corrosion process of the aluminosilicate based refractory materials. A laboratory test and procedure, simulating the conditions at the metal line in the aluminum treatment furnaces, was used. Different aluminum alloys (A1-5wt.%Mg, A1-5.5wt.%Zn and 7075 alloy) and chloride or fluoride salts (MgC12, KC1, CaCl2, NaC1, MgF2, CaF2, NaF and cryolite) were used as well as several aluminosilicate materials. Thermogravimetric measurements were also carried out in order to analyze the effect of the salts on the oxidation of molten aluminum alloys. The experimental results showed that fluoride salts are more aggressive than chlorides against the tested refractory products. It is postulated that the fluorides prevent the formation of a protective oxide layer on the metal surface, favoring at the same time the corrosion of refractories. Moreover, it was found that the presence of Na in fluoride salts increases significantly the aggressiveness of the aluminum alloy towards the refractory samples.

Jan 1, 2004

The following guidelines have been recommended by the Diamond Exploration Best Practices Committee established by the Canadian Institute of Mining, Metallurgy and Petroleum. These guidelines are applicable to public companies and their consultants reporting diamond exploration results. In respect of these guidelines, Diamond Exploration Results are results derived from the initial activities undertaken to investigate a diamond bearing prospect or deposit, to generate tonnage, grade and value estimates that cannot be classified as a Mineral Resource or Mineral Reserve. They do not address the earlier stage reporting of geophysical, geochemical or kimberlite indicator mineral results. Public reports of Diamond Exploration Results relating to mineralization not classified as Mineral Resource or Mineral Reserve must address the confidence limits of the result and contain sufficient information to allow a considered and balanced judgement of the significance of the results. The objective of these guidelines is to assist public companies and consultants in making appropriate disclosure of diamond exploration results by reporting in a manner which is: ??Uniform within the diamond exploration industry; ??Consistent with reporting from other industry sectors; ??Comprehensive; ??Unambiguous. The guidelines are not prescriptive. Materiality is the overriding principle that determines the information that should be disclosed. However, where a company or consultant deviates from the guidelines, the disclosure or technical report should state the extent to which the guidelines have not been followed, and the reasons for the deviation. The guidelines do not in any way replace jurisdictional reporting requirements (For example, the requirement for Canadian reporting issuers to comply with Canadian Securities Administrators National Instrument 43-101 by having technical disclosure endorsed by a Qualified Person as defined in that legislation).

May 1, 2003

By J. Marks

The measurement of greenhouse gas (GHG) emissions from primary aluminium production and inventory of these emissions of carbon dioxide and PF Cs have become an important issue for primary aluminium producers. Most global producers have either voluntary emission goals or emissions limits established through national regulatory requirements. International good practices for inventory of these emissions for national governments are established through the Intergovernmental Panel on Climate Change (IPCC). The current good practices, last updated in 2000, are being revised and are expected to be adopted by governments in the spring of 2006. There are a number of changes expected in the guidance that will impact how facilities account for their GHG emissions. This paper describes the changes to the guidance and the implications of these changes for aluminium producers.

Jan 1, 2006

By S. D. Logan

This presentation describes a lightweight automobile body structure concept developed at DaimlerChrysler to support a high fuel-efficiency vehicle project. This body structure consisted primarily of large thin-wall magnesium castings and resulted in a more than 40% weight reduction with a minimal cost increase over a conventional steel structure while achieving significantly improved structural performance as evaluated through CAE simulations. One concept vehicle was built for the purpose of demonstrating concept feasibility. Several slides showing the prototype build process are presented. The presentation also describes several large thin-wall die casting body applications that are in current production or have been used in recent production automotive applications and identifies areas where further development could improve the chances of a magnesium intensive body structure becoming a production reality at a later time.

Jan 1, 2006

By R. Ham-Su, J. P. Healey, S. P. Farrell, R. S. Underhill, M. A. Gharghouri, C. V. Hyatt, L. M. Cheng

Magnetic shape memory alloys (MSMA's) are a class of materials where magnetic energy can be converted into mechanical energy and vice versa. NiMnGa-based MSMA's have attained magnetic field induced strains up to approximately 10% and have a relatively wide operating temperature range, from well below 0°C to above RT, making them very attractive for a variety of applications. However, these materials also suffer from low toughness. Using these materials in a composite could mitigate this shortcoming, and also overcome limits imposed by inertia and eddy current losses. In this work, we describe the manufacture and characterization of such composites. Composites with 30% by volume MSMA were fabricated under a magnetic field resulting in anisotropic magnetic properties. Damping properties were evaluated by dynamic mechanical analysis.

Jan 1, 2004

By T. Velea

The most widespread methods for producing metallic copper are smelting of copper sulphide concentrates (which generates various types of polluting substances) and the hydrometallurgical route which consists of leaching in sulphate and chloride media (usually employing high temperature, high-pressure and special equipments). This paper presents a process, called VEPE, which consists of oxidizing copper sulphide concentrates in weak alkaline media (Na2C03 orland NaOH solutions), under low pressure and with air sparging. The oxidized concentrate contains less than 0.4% S. Copper is recovered from the oxidized concentrate by the standard leaching-solvent extraction-electrowinning route, with a total efficiency of 98% extraction. The proposed technology could represent a good opportunity to recover copper from sulphide concentrates in a clean, simple and profitable way.

Jan 1, 2007

By S. Orzecki

The KGHM Copper Refinery Plant, Glogów 1, has operated for 35 years and -increased its capacity almost ten times.Cathode quality, expressed in terms of the total impurity content, has undergone a five-fold improvement. The present refining capacity is equivalent to 240,000 metric tonnes of copper cathode, with a total impurity content of 20 ppm, inclusive of 10 ppm Ag. These accomplishments result from combined implementation of current technological progress in electrolytic refining and KGHM's own solutions applied to the Glogów Refinery. The quality improvement measures feature both lowering actual current density, despite an increase in nominal current density, and diminishing the role of non-ion mechanisms which transfer impurities to cathodes. The paper contains a detailed discussion of these issues and outlines possible measures aimed at further production and quality improvements.

Jan 1, 2007

By G. B. Harris

A process for the recovery of copper from the waste oxide copper of a mined-out sulphide orebody is described. Hydrometallurgical recovery of copper from this and similar wastes has been tried several times previously without success. Leaching is carried out by sulphuric acid in columns under conditions that minimise the iron content of the pregnant leach liquor, and copper is then recovered by ion exchange rather than the more conventional solvent extraction. The resin is stripped by spent electrolyte and copper is electrowon. Results are presented for testwork originally carried out in 1993, and repeated in 2006, and the novel aspects of the process, leaching and ion exchange, are discussed. Finally, preliminary order of magnitude capital and operating costs are given, demonstrating that the process is cost effective.

Jan 1, 2007

By Marta Polgari, Eva Surova, Bohumil Molak

Abstract -The Ûrkút rhodochrosite deposit and Branisko Mn showings (rancieite, manganiferous calcite), located in Lower Jurassic marine sedimentary rocks with black shale, were studied by organic­ geochemical methods. Both depositionallocalities were affected by the Lower Jurassic Toarcian anoxic event. Ûrkút shales are rich in organic matter (av. 2.94 wt% total organic carbon), the composition of which indicates derivation mainly from marine sources, with some terrigenous component. The shales matured in a bacterially active environment under reducing conditions of diagenesis-catagenesis. Branisko shales (?0.2 wt% TOC) with lenses of Mn oxide ore were weakly metamorphosed and their organic matter thermally degraded. The model for Mn carbonate ore formation envisages reaction of Mn derived from sediments, with carbonate generated by a bacterially mediated process of decom­ position of organic matter that also involved Mn reduction.

Jan 1, 1992

By Andreea Catalina Gluhoi

Oxidation and reduction reactions of N-containing molecules have been studied over different types of gold-based catalysts, Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 (M, MI, MII=Li, Rb, Mg, Ce, Zr, Mn, Cu) prepared by deposition precipitation with urea. In general, all the catalysts were already active at low temperatures. NH3 oxidation was effectively catalyzed by Au/CuO/Al2O3, a catalyst which also gives the highest yield in N2. NO reduction by H2 performed over gold-based catalysts produced N2O, N2 and NH3 and N2O reduction resulted in the formation of dinitrogen. For all the reactions, large synergistic effects have been obtained by addition of different kind of additives.

Oct 1, 2003

By G. Plascencia, A. Warczok, M. Zamalloa, T. Utigard, N. Behnood

The objective of this investigation was to investigate interactions between high-grade copper mattes and Rexal 60DB direct bonded basic bricks. The infiltration and attack of Rexal 60DB bricks by copper matte and continuous converter matte was investigated in laboratory tests at temperatures up to 1300 °C. The brick dissolution and infiltration tests did not show any significant difference between the 70% Cu and the 81% Cu mattes. More metallic copper was visible in the pores in the case of 81% Cu matte. An important mechanism for direct-bonded magnesia-chrome brick destruction is that oxysulphides start to infiltrate the brick, followed by slow oxidation of the matte producing metallic copper and cuprous oxide, which then react with MgO and Cr2O3, primarily attacking the direct bonds of the brick.

Jan 1, 2004

By R. A. L. Drew, C. A. Rodríguez González, Caleym W. F.

This work addresses the need of new refractories for copper converters. Technological improvements and environmental regulations for chromium containing refractories have generated this need. Chemical interactions, mechanism of penetration and the effect of oxygen potential and temperature in the system Cu2S-FeS-SiO2-O2 are presented for two refractories: a burned magnesite chrome brick (typically used by the copper industry) and a chrome-free spinel direct bonded brick. The main difference determined in the refractory performance was the blister copper penetration resistance; burned magnesite chrome brick is penetrated while direct bonded brick is not. These results are very promising since blister copper penetration has been reported as the major cause of refractory wear. The results are explained in terms of refractory porosity and wetting characteristics.

Jan 1, 2004

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant’s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today’s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user’s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project’s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By Marcotte P.

Introduction Pneumatic jackleg rock drills are commonly used in underground mining operations. These tools are known to expose their operators to hand-arm vibration levels in the order of 20-35 m/s2 weighted (Wh). Thus, the majority of the workers who have cumulated several years of jackleg rock drill operation are affected by related health problems such as Raynaud's syndrome or carpal tunnel syndrome. Up to now, no efficient personal safety device was available to protect pneumatic rock drill operators against hand-arm vibration (HAV). To address this problem, an anti-vibration handle prototype for jackleg drills has been developed in a previous study. Then, a multi-partner project was launched to refine the prototype and commercialize an effective anti-vibration handle for pneumatic rock drills.

Feb 1, 2008