Search Documents

By Van E. Komurka

This paper presents a cost comparison of the driven pile foundations for two large Wisconsin Department of Transportation (?WisDOT?) projects in Milwaukee, Wisconsin: the Marquette Interchange South Leg, and the Canal Street Viaduct. The projects? geology is fairly similar, but their methods/approaches to pile foundation design and installation differ. Although the Marquette Interchange South Leg had deeper poor soils, its pile design was more-cost-effective than the Canal Street Viaduct?s. Potential reasons for cost differences between the projects are identified, and the effect of the different design and construction approaches on economics is discussed.

Jan 1, 2009

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Michael P. Balducci

Urban deep foundation projects contain unique risks that must be recognized by the parties involved. Common pitfalls must be recognized and avoided or addressed through contractual relations and corresponding insurance coverage. By understanding these pitfalls, examining the risk-apportioning clauses and corresponding insurance obligations, may the parties? desires and expectations be met.

Jan 1, 2008

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By S. T. Kok

This paper presents a case study in West Malaysia for passive piles failure in very soft marine clay in open excavation. In this particular case, the thickness of the very soft marine clay ranges from 5 m to 7 m (16 ft to 23 ft) from the ground surface. Preliminary site investigation reported SPT ?N? value of zero for the very soft marine clay. The design was based on a deep foundation utilizing driven piles to support the superstructure. During pile cap construction, the piles were subjected to uncontrolled open excavation, inducing bending moment in the piles, resulting in some cracked and broken piles. Analyses were carried out using an existing three-dimensional finite element code with a non-linear soil model to predict the response of these piles during excavation. Finally, the predictions of pile responses during excavation were compared satisfactorily with the observed results.

Jan 1, 2009

By S. Bang

In recent years, suction piles and suction anchors have been used as underwater foundations for various offshore structures. They have been proven very versatile, effective, and environmentally friendly. This paper describes the load resisting mechanism, installation, and design of suction piles and suction anchors. Also included are brief descriptions of three offshore structures that have recently been constructed using suction piles and suction anchors. They include: a new breakwater system utilizing gravity-type concrete caisson superstructure on top of concrete suction piles; a floating breakwater system utilizing embedded suction anchors; and a foundation system utilizing suction piles for temporary mooring of underwater tunnel elements.

Jan 1, 2009

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

By W. J. Grose

The Embankment Place office development over the platforms of Charing Cross Railway Station in London has presented many interesting and unusual problems to the engineers involved with the project. The main structure is supported on widely-spaced columns which penetrate the station platforms and underlying vaults, calling for high capacity foundations built in severely restricted spaces. Hand-dug underreamed piles were chosen. Whilst a conventional design approach was taken to size the piles, a detailed appraisal of ground movements was made to explore the effects of the new building loads on the existing foundations, not only beyond the site perimeter but also those amongst the new foundations. Before construction of the pile proper could take place, it was necessary to sink a caisson through the upper unstable and water-bearing soils. This being identified as a high-risk item, a full-scale trial was carried out prior to embarking on the main works. The twenty-one hand-dug piles were 2.5m diameter, over 30m deep and belled out to between 4.5m and 6.6m.

Jan 1, 1989

By Mark H. Balfe

Over the last decade, Fenway Park has undergone annual improvements to modernize the facility for players and fans. These renovations include the Monster Seats, the Right Field Roof expansion, a new pavilion behind home plate, expansion of the Red Sox clubhouse, additional roof seating, and concourse improvements. Retrofitting the historic ballpark to bring it up to current standards required installation of foundations to support the new structural loads for each of the alteration projects. This required evaluation of existing conditions, and in many cases augmentation of the foundations at existing columns to accommodate the structural changes to the park. New foundations, generally consisting of drilled-in micropiles, were installed in numerous configurations and conditions. Since 2003, a total of 215 drilled-in micropiles have been installed to augment various columns around the park. The micropiles range in capacity between 40 and 70 tons and are installed through Fill and Organic Soils and embedded into the dense Glaciofluvial Sand and Gravel layer. Issues and learning related to the foundation augmentation include schedule constraints (work is typically conducted during the off-season and schedule is very aggressive), encountering old/abandoned utilities or foundations, ventilation of equipment, and management of spoils during micropile installation.

Jan 1, 2011

By Gordon Demetrick

3900 Yonge St. was not a typical site on which to build a condominium apartment. A steep hill covered the majority of the site. In order to use as much of this site as possible, the rear of the building was to have nine stores cut into the face of the hill. A permanent shoring system was required as the building structure was not designed to provide sufficient stabilizing elements to support the total earth pressure. The total excavation depth required was 36 m (120'-0") with the upper 12 m (40'-0") to be backsloped. The vertical face of soil to be supported was 24 m (80'-0'). The shoring system originally designed by the Structural Engineer was to support this face by installing soldier piles and inclined earth anchors. During bid preparation it became evident to us that the system as designed would be difficult and expensive to install due to wet soil conditions. An innovative design was required to overcome these problems. Anchor Shoring hired John Stephenson Consultants Ltd. to aid them in accomplishing this goal. After extensive investigation together with The Trow Group, a unique design was proposed which provided a practical solution to the shoring problem.

Jan 1, 1987

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as 'top down testing', has been used for many years and has become a 'standard' test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By Scott A. Walker, Roberto A. Lopez, Lori A. Simpson, David A. Shook

500 Folsom Street is part of the new Transbay neighborhood in San Francisco, which is being redeveloped after the 1989 Loma Prieta Earthquake damaged a freeway viaduct; removal of the viaduct created parcels of land available for development. The development consists of a 42-story residential tower with a six-level basement. The slender, core-only structure was designed using performance-based seismic design. Subsurface conditions include undocumented fill, Dune sand, marsh deposits, sand, and clay, all overlying sloping bedrock of the Franciscan Formation. The building is supported on a 10-foot-thick mat foundation approximately 62 to 72 feet below street grades; clay, sand, and bedrock are all present at mat subgrade. Under a portion of the mat, sand susceptible to liquefaction was present. The variable subgrade conditions and potential for ground failure, along with the depth of mat subgrade below street grade, created a challenge for the design and construction team to solve. The ground below mat subgrade needed to be improved to mitigate the liquefaction potential and provide more uniform support. The areal extent and depth of ground improvement necessary to support the mat with an acceptable amount of deformation was determined. Settlement was analyzed and subgrade moduli were provided for design of the mat, with multiple iterations performed to converge between the geotechnical and structural models. Based on the project schedule and logistics, it was beneficial to work from street grade to improve the ground. In order to target the depths below the mat and minimize wasted effort and materials within the depth of excavation, grids of jet grouting were determined to be the most economical ground improvement method; however, it was challenging to install the columns from 65 feet above the top of the target zone. During installation, QA/QC was performed to check that the jet-grouted columns were installed to the design depth and diameter and developed the design strength.

Jan 1, 2018

By Rudolph P. Frizzi

Quality control is essential for augered cast-in-place (ACIP) piles (also known as continuous flight auger (CFA) piles outside the United States) and drilled displacement (DD) piles since the pile is constructed below the ground surface out of the direct sight of the personnel constructing and inspecting the pile. ACIP piles are being successfully constructed to support high-rise structures, hospitals, arenas and stadiums, mass transit systems, and power and industrial facilities. The use of DD pile technology is also gaining ground in the United States, typically utilizing proprietary systems such as Omega (currently utilized by Richard Goettle Inc., and LG Barcus and Sons, Inc.), Berkel, and DeWal (currently utilized by Morris-Shea). Different types of ACIP/DD pile installation equipment are shown in Figures 1 and 2. ACIP piles are installed into granular and cohesive soils, and soft rock to lengths currently approaching 130 ft (39.5 m), with diameters up to 24 to 36 inches (610 to 915 mm), and sustaining design loads approaching 900 kips (4000 kN). Current DD pile installation equipment in the United States is capable of installing up to 79-ft-long (24 m) piles with diameters ranging from 12 to 18 inches (305 mm to 460 mm).

Jan 1, 2003

By Daniel J. Rider

In 1980 the Niagara Frontier Transportation Authority contracted for three miles of cut and cover box structure and station construction in Main Street, Buffalo, New York. Project depths ranged from 30 feet to 60 feet below street grade. Soils, Figure No. 1, consisted of loose to very compact sands and gravels. Ground water level was generally 20 feet below grade. Specifications required a soldier pile and timber lagging support system with external dewatering. Soldier piles were to be installed in prebored holes with bentonite slurry and lean concrete backfill. Conventional pile driving was not allowed due to concerns over excessive noise and vibrations and its effect on nearby historic structures and the surrounding population

Jan 1, 1987

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine's Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By Michael Arnold, Bob Faulhaber, Joe Nichols

"Center Hill Dam is a critical part of the infrastructure controlling floods at the Caney Fork River and reducing flood levels at the Cumberland, lower Ohio and Mississippi Rivers. The Center Hill Dam Foundation Remediation Project was necessary to address Karst features in the foundation rocks and observed signs of distress of the dam. From 2011 to 2014 BAUER Foundation Corp. (BFC) performed deep foundation works for this project. The executed features of work include the installation of two walls. The first wall extends throughout the clay embankment into the underlying rock to provide encasement during the construction of the second wall. Its width of 7.4 feet makes it the widest diaphragm wall ever installed. The second wall is the actual seepage barrier and provides a continuous 2- feet wide wall. It extends through the first wall into the underlying rock and is up to 300 feet deep. The paper introduces the project, the requirements specified by United States Army Corps of Engineers (USACE) for encasement and barrier wall and the approaches taken by BFC. It discusses the ground conditions and describes the excavation equipment as well as the excavation methods used. A special focus is put on the steering capabilities of the hydrocutter equipment and the verticality performance.PROJECTBeginning in 2011, BFC was tasked by the USACE with the installation of a seepage barrier/cutoff wall at the Center Hill Dam Foundation Remediation project under a partially performance based specification. The remediation was necessary due to karst features in the foundation rocks and observed signs of distress, which led USACE to rate the dam with the most critical dam safety action classification (DSAC I). The executed features of work include the installation of two walls. The first wall, an encasement wall, extends vertically through the clay embankment and is embedded minimally into the underlying bedrock to provide embankment stability during the construction of the second wall, the barrier wall. The encasement wall is constructed of overlapping panels 7.4 feet (2.25 m) wide, which is the widest diaphragm wall ever installed, and up to 210 feet (64 m) deep. The second wall is the seepage barrier and provides a continuous 2 feet (0.6 m) wide wall consisting of overlapping panels. It extends through the encasement wall into the underlying bedrock and is up to 307 feet (93 m) deep. BAUER BC40 and BC50 hydrocutters mounted on MC96 and MC128 foundation cranes were used to perform the majority of the works (Figure 1). Excavations were performed under bentonite slurry (encasement wall) and water (barrier wall) and concrete was poured with the tremie method. Adding to the challenges, the project had to be executed in an environmentally sensitive area. Based on the high risk, a special focus was put on monitoring, quality control and geometric accuracy. The WallTracker information management system was used to share all relevant data between BFC and USACE (Roff et al. 2014)."

Jan 1, 2017

By David B. Paul

"ABSTRACTThe US Army Corps of Engineers (USACE) has 704 dams in their inventory and over 100,000 miles of levees with a capital value of over $150 billion. Currently, there are 319 dams that are classified as high hazard and have actionable failure modes that will require structural modifications. The most frequent actionable failure mode associated with the inventory is seepage and piping. One of the most effective engineering solutions is the installation of a cutoff to limit seepage. Currently, USACE has over $1.5 Billion of cutoff wall projects under construction and/or design. Given the magnitude of the dam and levee safety issues, USACE is developing a new Engineering Manual (EM) titled “Seepage Control Cutoffs for Dams and Levees.” This EM covers all of the methods to construct cutoff walls. USACE has partnered with the Deep Foundation Institute (DFI) in preparation of the EM to ensure that it is comprehensive and draws from the expertise of the specialty foundation engineering companies that design, manufacture, and construct seepage control cutoffs around the world. The EM contains case histories as well as a comprehensive project statistical summary and guide specification paragraphs. The goal of USACE was to make the EM a state of the art document for use by Districts.HISTORYSlurry wall construction techniques were developed in the late 1940’s in Italy by ICOS. The first use of the slurry trench method of construction in the United States was by the USACE Memphis District in September 1945, to form a partial cutoff along the Mississippi River levee on the Arkansas side of the river just below Memphis, Tennessee. The idea for the project probably evolved from the use at that time of puddle clay trench cutoffs combined with the use of drilling mud for advancing borings. A paddle wheel mixing device was constructed for making slurry from native clays. Trenches were dug to a 20-ft depth using a trenching machine and to a 35-ft depth using a dragline with a 100-ft boom and 2-cu-yd bucket. Backfill was mixed in windrows at the site from hauled-in clay gravel and native materials and pushed into the trench by a bulldozer when the length of the trench was equal to about twice the trench depth. It is amazing that after almost 70 years, the technique is still about the same as it was when first developed by the Memphis District. A soilbentonite cutoff was constructed under the Kennewick Levee adjacent to the Columbia River as part of the McNary Dam Project in Washington by the Walla Walla District in 1952 The first application of a soil-bentonite slurry trench cutoff for control of underseepage at a major earth dam was at Wanapum Dam on the Columbia River in Washington in 1959.The first cement- bentonite cutoff in the United States was constructed at the Tilden Tailings Project to store tailings from the Tilden Mine in Michigan in 1976. The first cement-bentonite cutoff constructed at a dam on a river retaining a reservoir in the United States was completed in 1978 at the Elgo Dam (formerly the San Carlos Dam) in Arizona.The USACE has designed and constructed some of the deepest and most complex cutoff walls for dams since the 1970’s. The first major concrete panel cutoff wall constructed in a dam in the United States was at Wolf Creek Dam (Nashville District) by the ICOS Corporation between 1974-77. The dam has a long history of seepage issues associated with the karst geology that comprises the foundation. In 1968, about 17 years after first being impounded, wet areas, muddy flows in the tailrace and sinkholes in the downstream toe adjacent to the switchyard occurred."

Jan 1, 2014

By Gerald Verbeek, Erick Baziw

Downhole Seismic Testing (DST) is a very popular applied seismology site characterizing tool within geotechnical engineering. A challenging aspect of DST is to characterize the acquired seismic data sets to determine the analysis method that will result in the most accurate interval velocity values. BCE has invested considerable resources into developing Seismic Trace Characterization (STC), which uses various independent parameters of the acquired data at a particular depth. Initial work in this area resulted in the selection of the linearity estimate from the polarization analysis, the cross correlation coefficient of the full waveforms at the particular depth and the preceding depth and a uniquely developed parameter referred to as the signal shape parameter for this characterization. Subsequent analysis in STC identified two other parameters: the Signal-Noise-Ratio (SNR) and the Peak Symmetry Differential (PSD). The paper briefly describes these parameters and then outlines how they can guide the data analysis to derive more accurate results, especially near surface, which is especially important to assess the liquefaction potential in areas prone to earthquakes, such as California. The process will be illustrated with actual data from another area prone to earthquakes, namely New Zealand. 1. INTRODUCTION The near surface characterization of low strain in-situ shear wave velocities (VS) has proven critical for liquefaction assessment. Liquefaction is a phenomenon in which dynamic loading of saturated soil results in the material properties to change suddenly from a solid state to a liquefied state. VS is an important parameter for evaluating liquefaction potential due to fact that it is influenced by many of the variables that influence liquefaction (e.g., void ratio, soil density, confining stress, stress history, and geologic age (Andrus et al., 1997)). Aki and Richards (2002) also outline that the amplitude of ground motion should depend on the density and shear wave velocity of near surface soils and rocks according to the theory of wave propagation. Since the change in density with the increase in depth is relative minor compared to that of the shear wave velocity, the latter is a very useful parameter to represent site conditions (Stewart et al., 1997). Bray (2014) and his colleagues carried out an extensive geotechnical analysis of the catastrophic liquefaction that occurred in Christchurch, New Zealand in 2010 and 2011 and found that near surface rather than deep liquefaction resulted in extensive foundation damage.

Jan 1, 2018