Search Documents

By D. Szyszka

During passing gas bubbles through mineral suspensions, some mechanical carryover of fine particles to the froth layer always takes place. The entrainment of mineral particles is influenced by many parameters, mostly by the particle size and the concentration of the frother. The paper deals with influence of selected frothers (methylisobutylcarbinol (MIBC), a-terpineol, and hexadecane tricosaethyleneglycol ether (C16E23)), common laboratory flotation frothers, on the mechanical car-ryover of quartz, a typical gangue mineral component of ores. Entrainment tests were carried out in a laboratory Mechanobr flotation machine with quartz particles suspended in aqueous frother solu-tions. The mechanical recovery of quartz in the presence frother was increasing with time and reached plateau after about 20 minutes of flotation. The plateau level of quartz recovery depended on the frother concentration. Initially an increase of the plateau with frother concentration was observed until the plateau reached the highest level called the maximum recovery emax. The emax can be used as a parameter to characterize the ability of frothers to entrainment. In the studied quartz-frother flotation system the maximum entrainment was 32%, 50% and 80% for methylisobu-tylcarbinol (MIBC), a-terpineol, and monohexadecane tricosaethylene glycol ether (C16E23), re-spectively. A comparison of the maximum entrainment factor emax with other, known from literature, indices such as bubble critical coalescence concentration (CCC), dynamic foamability index (DFI), Jw, e =25%revealed, except DFI, their similarity.

Jan 1, 2014

By D. Vega, P. R. Brito-Parada

"Small diameter (10 mm) hydrocyclones have been applied successfully for the separation of particle suspensions in the micron size range. These hydrocyclones are attractive because they show a bypass fraction larger that the water recovery, resulting in a high particle recovery to the underflow as well as low water recovery. However, this is a disadvantage when the purpose of the hydrocyclone is classification because of the large amount of fine particles that are misplaced in the underflow. The aim of this study is to explore, experimentally and computationally, the influence of design parameters on the classification process. In this work, a full factorial experimental design was defined to carry out comprehensive experimental tests using glass beads (0-20 µm) as the particulate system. We show that the dimensions of spigot and vortex finder diameter can be effectively manipulated to change the separation performance of the system and the energy consumption. A CFD model was developed that is able to predict particle size distribution. The numerical results for the partition curves showed very good agreement with the experimental data. INTRODUCTION Small diameter hydrocyclones are a very attractive separation technology for fine particle suspensions. Since the hydrocyclone diameter is directly proportional to the cutsize that can be achieved, 10mm hydrocyclones have been shown to be very effective in collecting particles in the micron-size range. In addition, while in large hydrocyclones the bypass, i.e. the fraction of particles that report to the underflow without classification, is similar to the water recovery, in 10mm hydrocyclones the bypass fraction is considerably larger than the water recovery. Its high particle recovery and low water recovery makes small hydrocyclones ideal for ultrafine particle classification and dewatering applications in mineral processing. The separation of mineral suspensions achieved using small hydrocyclones has been the focus of various studies. Pasquier and Cilliers (2000) derived a general classification model from experimental data of fine silica concentration in 10mm hydrocyclones; the model was able to describe the fish-hook partition curve. The effect of operating conditions has also received some attention in the literature. Cilliers et al. (2004) showed that an increase in temperature positively effects the recovery of fine silica particles in small hydrocyclones, by increasing the bypass and decreasing the cutsize. Neese et al. (2015) showed that the cutsize in 10mm hydrocyclones can be further decreased by operating at higher pressure, which also trebled the throughput."

Jan 1, 2018

By B. Z. Wu

The ore dressing of tin-polymetallic lean ores is a difficult problem and the research emphasis in domestic nonferrous metals mining field. Through research and tackle key problem,and in order to supply reference in dealing with the same types ores, this paper expatiates the exploiture and appli-cation of six item new technology and technics in ore dressing of tin-polymetallic lean ores. It include the technics of multi-step compounding disposing tailings, grinding step by step, grinding and processing circularly technology, high thickness without circle flotation technology, dispersedly flotation tin step by step technology, exceed fine lean plumbum stibium zinc flocculation flotation technology, the synthetically recovery of waste water after ore dressing technology.

Jan 1, 2014

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By P. K. Fedotov

Annually at least 5% percent of world power consumption is involved in the process of ore dressing while ore processing technology. Such rate of energy consumption demonstrates the importance of a given process study in the human life-sustaining activity. Examining of interparticle destruction being under external stress pressure in ore responses this problem solution at the greatest degree. The technology of destruction in the roll press is of great interest. The use of the given equipment allows to save a significant amount of energy by means of the built-in ore destruction mechanism. Examination of stress-strain fields which determine the level of interparticle destruction between the rolls in the ore layer enables to specify both level of ore destruction and power consumption. The mathematical computer modeling for the deformable environment use based on the finite-element method (FEM) allows to carry out the given research. We use FEM solution for elastic contact problem for the most complete study of power consumption employed in ore and interparticle destruction. This problem solution allows also to examine energy consumption expenses spent for ore crushing in the roll press. Also we have identified the mechanism of ore in a layer of the particles under pressure roller press. It is established that high level of performance and reduction of energy consumption in interparticle destruction of ore in the layer due to the appearance of the gradient of normal stresses in contact of particles of mineral raw materials. The algorithm has been developed determining crushing product particle size distribution of fractured particles in the layer, using the Bond’s theory of crushing. The use of our FEM model reduces the time of equipment selection for new plant and at the design stage to reduce the risks of errors in the choice of roller presses.

Jan 1, 2018

By P. K. Fedotov

Centrifugal separation opens its new application fields in the Mining Industry. The up-to-date equipment for ultra-fine ore and concentrates grinding allows an efficient use of centrifugal concentration for micronic gold grains recovery. Moreover, advanced centrifugal concentrators are presented on the market: concentrators with continuous concentrate discharge designed both for ore and non-metallic minerals concentration process. The conducted tests proved the centrifugal concentration to be efficient process for gold recovery from finely ground concentrates and ores (less than 20 µm). Knelson concentrator application for such a fine material in different process circuits makes possible to raise the total gold recovery level of plants. In the circuits of coal plants and in course of coal slimes treatment the centrifugal concentration may be used before flotation in order to improve process performances. A centrifugal concentrator KC-CVD with continuous concentrate discharge working on 0.3 (0.5)mm fraction before flotation is

Jan 1, 2014

By Andrzej Luszczkiewicz, Aleksandra Potulska

"Flotation is a basic process of beneficiation of mineral raw materials which requires very fine grinding for liberation of valuable minerals. Probably flotation will also play this role in the future. In the case of flotation of difficult-to-upgrade non-ferrous ores, currently one of the most important trends in technology development is solution to fine grinding even down to a few micrometers in size and elaboration of effective flotation technology for such fine particles. Both industrial flotation data and many investigators suggest that the best results of flotation of ore minerals are observed for particle size range from 20 to 100 µm. Many base metal ores require grinding below 20, or even 10 µm, to liberate valuable ore components. However, industrial flotation of particles below 20 µm in size creates numerous challenges. Further complications may be caused by a complex nature of the ore, especially when the valuable metals are present in several different sulfide minerals. This problem occurs in the case of the Polish sedimentary copper ores. In the present study, flotation of the ore of different size distributions and degrees of grinding, having the size of particles below 25 µm, was investigated. The behavior of different sulfide minerals naturally present in the ore was analyzed. The best results of flotation tests were obtained for the ore ground down to 95% below 25 µm. Narrow size fractions -10; 10-15; 15-25; 25-40, and +40 µm were separated using special micro-sieves and mineralogical as well as chemical analyses of each size fraction were carried out for monitoring the behavior of the fine sulfide particles. Differences between flotation of chalcocite-digenite, bornite, chalcopyrite, covellite, galena and pyrite-marcasite naturally occurring in the ore were described. The role of different particle sizes in flotation performance of each mineral was also presented."

Jan 1, 2014

By S. L. Gubin, T. V. Ignatova, A. V. Levshin, D. O. Sharkovsky

"Flotation process applied for concentration of unoxidized ferruginous quartzites by PJSC Mikhailovsky GOK (MGOK) is based on wet magnetic separation of strong magnetic minerals. However quality of the resulting concentrate (Fe65-66%) is insufficient for production of metallics. Quality upgrade of magnetite concentrate via flotation has been implemented by MGOK to produce premium quality magnetite concentrate.Flotation is a challenging process due to sensitivity to varied amounts of reagents, fine and coarse mineral ratio, particle contact (retention) time and temperature of feed. Tomah’s PA-14 reagent (USA) has proven efficient for application in flotation of MGOK’s magnetite concentrate.Objective of this work is to select and prove applicability of selective agents for flotation upgrade of magnetite iron ore concentrate.Series of flotation tests has been carried out with application of new highly selective collecting agents produced by Akzo Nobel (Sweden), Clariant (Germany) as well as Akzo Nobel’s and Tomah’s cationic collector mix to improve performance efficiency of flotation process. Tomah’s flotation agents and Akzo Nobel’s Lilaflotproved to be the most effective for purposes of concentrate quality upgrade to Fe69.0% via flotation.Testing Method: Following scientific research methods were applied for testwork: system analysis, mathematical statistics, observation, comparison, trial (experiment).To determine key process factors a series of pilot tests was carried out. Most of the testwork was performed by PJSC Mikhailovsky GOK’s Central Process Laboratory.Work Results:-optimized flotation performance modes were defined to ensure production of three types of low-silica concentrate, i.e. containing SiO25%, SiO24% and below SiO23% by weight. Most efficient selective agents applicable for flotation have been defined. Mixture of higher aliphatic amines has proven to intensify selective flotation of quartz. It enables higher yield of chamber product maintaining desired quality of concentrate.Achieved process operation and performance factors have been revaluated.Value for Advancement and Expansion of Mineral Processing:Flotation of concentrate has enabled expansion of PJSC Mikhailovsky GOK’s production capacity, improved production quality, helped to maintain sustainability and competitive advantage of the company."

Jan 1, 2018

By D. Moradkhani

The heap leaching of oxide copper ores with copper cathode recovery by solvent extraction and electrowinning is now well established as a low-cost method of copper recovery. The main purpose of this study was to extract copper from the copper low-grade oxide ore of Chodarchaei mine using column leaching. The copper oxide ore contained 1.1% Cu and 1.75% Fe. The mineralogical analysis indicated the malachite (Cu2(OH)2CO3) was mainly composed of oxidized phases. The sulfuric acid leaching experiments were performed under the laboratory conditions. The influence of several parameters on the course of the reaction such as particle size, acid concentration, flow rate, and time was examined. The optimum collective extraction of copper and iron was obtained at a particle size of +10-15 mm for a leaching duration of 3 days with sulfuric acid concentration of 100 gpl and using a flow rate of 2.5 cc/min. Under these conditions, the recovery of copper and iron were 98.54% and 41.99%, respectively. Keywords: column leaching, copper, iron, working diagram.

Sep 1, 2012

By Tracy Shimmield, Philip Samar

"Metals have been mined as ores since pre-history but metal production has increased dramatically in modern times driven by expanding Global GDP. Metal ore mining produces large amounts of waste rock and mine tailings. Mine tailings are the wastes produced after extracting the desired metal from the ore. There are several ways of dealing with this waste, and Ritcey (2005) identifies the following possibilities, land-based storage, backfill to the mine, deep lake disposal and marine disposal. In Papua New Guinea (PNG), both Misima and Lihir Mines adopted the marine disposal option, releasing tailings through a submerged pipe onto the sea floor. This special case is referred to as Deep Sea Tailings Placement (DSTP) in which the tailings deposition is sufficiently deep as to be below the euphotic zone. The most important aspect of deep sea tailings placement is that the tailings are deposited at great depth where exchanges between the seabed and the surface layers are small. The first quantitative multidisciplinary study of tailings impact on the deep sea was carried out from 2006 to 2010 in Papua New Guinea. The physical, chemical and biological work carried out has placed PNG at the forefront of research into the assessment and management of deep-sea environmental impacts related to mining in PNG. The study has provided data which has led to a better understanding of the ecological and geochemical processes in deep water that accompany DSTP in PNG and provided baseline data on deep-sea ecosystems in a scientifically poorly known tropical ocean. Additionally, guidelines on best practice for DSTP have been developed Here we present geochemical data obtained from sediment samples from the marine environment surrounding Lihir and Misima Islands."

Jan 1, 2014

By G. Weingrill, H. Flachberger, J. Neubacher

The so called Bublon®-process is an innovative process for the controlled expansion of volcanic glasses such as Perlite and for thermal treatment of other minerals. In this manner, functional light fillers with astonishingly altered physical properties can be manufactured. In contrast to conventional Perlite expanding processes no fossil fuels are burned in order to achieve the expansion. Instead, the feed material is heated electrically mainly by radiation based on heat transfer from heating elements. The main advantage is the better controllability of the production process. Therefore, the heating elements are segmented along the flow of the particles, hence in direction of the ongoing expansion. Overheating of the particles, which ultimately leads to the destruction of the particle surfaces and consequently decreasing the quality of the expansion product, can be reduced significantly. Due to flow characteristics and settling behaviors of fines the lower particle size limit of the feed in this process is restricted to not less than 100 µm. Otherwise process instabilities are to be expected. Manufacturing industry demands light and fine hollow microspheres. Therefore, a proven cooperation between Montanuniversität Leoben and Bublon GmbH was formed to develop a new process called ‘Bublite’. This issue was addressed by changing the conveying principle into a pneumatically conveying system transporting particles from the bottom to the top of the kiln by the means of a drag flow. This approach makes it possible to handle the difficult flow patterns in the kiln and to control the retention time of the particles in the heat transfer zone. As a result, it is now possible to expand very fine Perlite particles into a high quality functional lightweight filler with a glazed-closed surface. The dependence of the polymer industry on importing this kind of fillers from overseas can be reduced by producing it close to sites of demand. Also the Perlite mining and processing companies benefit from this technology because the mine lifespan and the output of the processing plant can be increased.

Jan 1, 2018

By Andrei Yevdokimov, Ivan Sidorov, Olga Lanchakova, Olga Khmelnitskaya, Tatiana Chikina

"The paper focuses on the results of the research on development of hydrometallurgical process of gold recovery from refractory sulfide flotation concentrates based on fine and ultrafine grinding. Refractory concentrates (the degree of refractoriness is 16.9%-82.6%) were chosen for testing. The efficiency of the process based on fine and ultrafine grinding to treat flotation concentrates with gold intergrown with sulfides and rock-forming minerals was shown. Based on the test work conducted, the process option was chosen. In included grinding of flotation concentrate to the size of 98% minus 20µm in a bead mill, lime treatment with air blow, CIL, filtration and detoxification of liquid phase of the slurry. This process (compared to the basic option) provides the recovery of gold from 82.6%, up to 94.0% and decreases the residual grade in the tailings from 3.3g/t to 1.1g/t at the consumption of 12.6NaCNkg/t. Based on the results of the test work and pilot plant testing, project design criteria of flotation circuit at a Russian plant was developed."

Jan 1, 2014

By V. A. Ivanova, T. N. Perunkova, N. O. Dorozhanova, G. V. Mitrofanova

"Oxyethylated compounds are used as reagents-regulators in the flotation of non-sulfide ores, in particular, apatite-containing ores. Thus, the necessary degree of selectivity in the flotation separation of two calcium-containing minerals of apatite and calcite is achieved only by using, in addition to a collector, regulators-reagents from the nonylphenol ethoxylates class. In order to establish the most optimal structures, this paper presents a comparative assessment of the physical-chemical and flotation properties of several classes of oxyethylated compounds - alkylphenol ethoxylates, aliphatic alcohol ethoxylates and oxyethylated carboxylic acid. The authors have studied their dispergating ability with respect to the air phase and calcium soaps of the carboxylic collector. Dependences of foaming properties of regulators on the degree of oxyethylation have been determined. Adsorption isotherms of sodium oleate on apatite and calcite in the presence of regulators have been obtained. It has been shown that the presence of oxyethylated compounds in the solution reduces the amount of the adsorbed fatty acid collector. The influence of the considered classes of regulators on apatite flotation has been studied. The interrelation of flotation properties of oxyethylated compounds and their molecular structure has been established.INTRODUCTION Flotation plays a leading role in complex apatite-containing ores processing. However, two calcium-containing minerals - apatite and calcite, which compose apatite-carbonate ores, are characterized by close flotation properties. Selective separation of these minerals is a difficult task, the solution of which is impossible without using reagents-regulators. One of the ways to ensure the selectivity of the flotation separation of calcium-containing minerals is the use of reagents-depressants such as sodium silicate, starch, cellulose derivatives, and others (Liu et al., 2016; Rao et al., 1989). Another method is the application of nonionic reagent regulators (Filippov et al., 2016; Filippova et al., 2014; Ignatkina, 2017), which contribute to the adsorption of the ion collector (Filippov and Filipova, 2006 Rao and Forssberg, 1997) and stability of formed froth (Sis and Chander, 2003)."

Jan 1, 2018

By Y. S. Sun, P. Gao

"In this investigation, a pilot-scale suspension magnetization roasting reactor was introduced and used to enhance magnetic properties of an iron ore. Consequently, the effects of roasting temperature, reducing gas CO flow rate and fluidizing gas N2 flow rate on the magnetization roasting performance were investigated. The results indicate that the hematite and siderite are almost completely converted into magnetite by a gas mixture of 3.5 Nm3/h CO and 2 Nm3/h N2 at roasting temperature of 520 °C. Under the optimized conditions, the magnetic iron concentrate with an iron grade of 60.18% and iron recovery of 90.17% was achieved. The XRD and Fe mineral phase analyses revealed that most of the hematite and siderite were converted to magnetite, and the magnetic properties were greatly enhanced. INTRODUCTION The steel and iron industry in China has rapidly developed in recent years requiring a large quantity of iron ores. Low-grade and complex iron ores are currently the overwhelmingly dominant mineral resource for iron in China. Therefore, China depends on imported iron ore resources heavily, resulting in an increase in the production costs of iron-making and steel-making[1-3]. Using domestic resources to produce a steady supply of high-quality iron ores is an important step toward the sustainable development of the steel and iron industry[4-5]. The iron ore from Jiuquan iron and steel company is abundant and recognized as typically complex iron ore resources in China. Magnetization roasting followed by low-intensity magnetic separation has been proven as the most feasible methods to upgrade refractory iron ore[6-10]. In present research, an innovative roasting technology, namely suspension magnetization roasting, was developed and applied to recover iron from a typical refractory iron ore. Suspension magnetization roasting technique and equipment developed by Prof. Yuexin Han’s Group at Northeastern University (NEU) is an effective way for the utilization of refractory iron ore. The advent of suspension magnetization roasting will, in China and even globally, produce a significant technological revolution in the field of iron ore beneficiation. Based on the previous works, this paper mainly described experiments on the separation and recovery of iron from a complex refractory iron ore by means of suspension magnetizing roasting and low-intensity magnetic separation processes. The purpose of the research is providing a new technology for effective utilization of refractory iron ore. Process parameters that affected the separation and recovery rate of iron were conducted and optimized, and the reaction process was analyzed by XRD and Fe mineral phase analysis."

Jan 1, 2018

By S. Serranti

A fast, reliable, and low cost characterization of ore minerals products, as they result from different processing actions, represents one of the most challenging targets in the mineral processing sector. Today different techniques are available according to different sampling strategies and analytical principles. In this paper, the possibilities offered by the adoption of hyperspectral imaging based sensing units working both at micro- and macro-scale are presented and discussed. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is thus possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection, and quality control actions to apply. Keywords: process mineralogy, hyperspectral imaging, NIR spectroscopy, surface mapping, textural analysis, quality control

Sep 1, 2012

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By John A. Herbst, Ming Song, Xiangjun Qiu

It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. The study described here shows that these new tools can allow the design of wear part profiles which will maximize mill productivity over the entire life of a liner/lifter system.

Jan 1, 2003

By Li Tianxia, Zhou Jing, Zhu Yimin

"A typical low-grade of high sulfur bauxite fr contains 54.71% Al2O3, 11.35% SiO2 while the ratio of aluminum and silicon was 4.25, and harmful components such as Fe and S graded 7.3% and 1.33% respectively. The ore is characterized by complex mineral compositions, fine dissemination of particle size of pyrite and diaspore, low desulfurization efficiency, and difficult separation of aluminum and silicon. In order to improve the degree of concentration, recovery and desulfurization efficiency on the basis of process mineralogy studies, the floatation behavior of high sulfur bauxite in the process of desulfurization and desilication were studied through laboratory tests and pilot plant tests. KEYWORDS high-sulfur bauxite; low grade; flotation; desulfurization;desilicication INTRODUCTION In order to solve the selection problem of bauxite mine area, we carried out technological mineralogy, laboratory test, small-expansion Dalian test to solve the problem of the refractory ore. Main research contents and conclusions were presented as followings :(1)Process mineralogy research shows: the main mineral components include diaspore, kaolinite, chlorite, pyrite, limonite. (2)Batch flotation tests indicated that slime can be dispersed well during desulfurization floatation when Na2CO3 was used as modifying agent. (3)Poilot plant tests shows that Batch flotation tests results are correct. 2?PROCESS MINERALOGY 2.1 Chemical Composition of Ore 2.1.1 Spectral Analysis of Sample The results of the semi-quantitative analysis of X-Ray -fluorescence spectra of the original ore are shown in Table 2-1. The results of spectral analysis show that the main components of the sample are O, Al, Si, followed by Fe, Mg, Ti, S and so on, while the content of other elements is very small. The value is Al, and maybe Ti, for bauxite, while Fe and S are unfavorable elements, and Si and Mg and Ca are the main impurity elements."

Jan 1, 2018

By Shibayama A.

In this research, an investigation of a process to selectively remove arsenic (As) and antimony (Sb) contained in enargite (Cu3AsS4) and tennantite/tetrahedrite ((Cu1,Fe)12(As,Sb)4S13) copper resources by leaching and precipitation were performed. First in the leaching process, the target was to selectively leach As/Sb and reduce their contents in the ores to <0.5 wt% followed by a second process to remove As/Sb dissolved in solution for environmental control. Enargite ore contained 3.65 wt% As while tennantite/tetrahedrite ore contained 5.40 wt% As and 4.85 wt% Sb. Alkaline leaching using NaHS?NaOH media at varying experimental conditions (temperature, pulp density, time, reagent concentrations) were performed to investigate the process. As/Sb precipitation studies were also performed to control high As/Sb concentrations in leach solutions by using elemental sulphur (So). Results from leaching studies showed that over 99% of As/Sb in the impure copper ores can be removed and their contents in the final solids reduced to <0.5 wt%. It was also established that such very high leaching could be achieved at 80°C within 1?6 h and pulp densities as high as 1000 g/L. The study also revealed that leach solution containing very high As/Sb concentration ranging from 5 to 20 g/L can be used as fresh solution for leaching of fresh ores until concentrations exceeding 35 g/L when it was sent to precipitation circuit for As/Sb removal. Addition of elemental sulphur at 90°C and fast cooling to 30°C allowed over 60% As/Sb precipitation and removed as Na3AsS4 and solution with reduced As/Sb concentration to leaching circuit for continuous use. Keywords: Enargite; Tennantite/Tetrahedrite; Selective Leaching; Precipitation; Sodium hydrosulfide;

Sep 1, 2012