Search Documents

By Katarina Theander, Robert J. Pugh

In the flotation process, control of the stability of the froth is extremely critical. In the case where the froth is too stable then mechanical entrainment of particles can occur but in the opposite case, where the froth is too unstable and difficult to skimm-off, then a reduction in recovery can result. In minerals and deinking flotation, commercial fatty acids are used and may act as both both collectors and frothers. However, frequently the fatty acids are mixed with nonionic ethoxylated surfactants to give more effective froth control and increase the flotation performance. It is of interest to note from the surface chemistry literature, that such mixtures may cause synergistic effects in surface activity which may explain changes in bubble size, foaming and carry over of particles. In the present study, we have carried out foaming and drainage experiment with oleic acid and model nonionic surfactants; hexa(ethylene glycol) mono-dodecyl ether, C12E6 and tetra (ethylene glycol) mono-dodecyl ether, C12E4 both in separate and mixed systems. Frothing was carried out in a column, equipped with a series of conductivity electrodes which enabled the water content of the froth to be measured along the length of the column, during various stages of the drainage process. The variation in water content of the froth enabled the process to be characterised by distinct three stages; (a) an entrainment state where the water transfer from the bulk phase to the froth was dominant (b) a steady state when entrainment and drainage are balanced and no water is transferred to or from the froth and (c) the drainage step when drainage predominates and the volume of the bulk phase increases. We also carried out surface tension measurements on the oleic acid/ nonionic systems and related the results to the frothing and drainage performance. From the surface tension data, the adsorption interaction parameter of the mixed systems at the air/solution interface could be calculated and was found to depend on the oleate/ nonionic surfactant ratio. This value was related to the frothing performance and the results indicated a positive interaction parameter for the mixed surfactant systems which could explained the synergistic effects in frothing performance.

Jan 1, 2003

By M. Pelser, Lorenzen L.

"The presence of calcium and magnesium in the hydrometallurgical processing of base metals, results in a number of process difficulties. These problems range from the contamination of the final product (where the final product is a precipitate) to high energy consumptions and large bleed streams during electrowinning. Calcium poses an additional problem in sulphate solutions owing to the low solubility of its sulphate salts. This can easily lead to a process stream that is supersaturated with calcium sulphate, resulting in unwanted solids formation within the process equipment.A review of literature has proven that there is no conventional method for the control of calcium and or magnesium, although a number of potential processes have been identified. The technologies investigated included precipitation, ion exchange and solvent extraction, for which at least one method was found under each. To make the reader aware of these processes a short description was provided of each within the text.Of these processes, fluoride precipitation was selected for experimental investigation based on the low solubility of calcium and magnesium compared to the base metals. This process involves the addition of a soluble fluoride to precipitate CaF2 and MgF2. The experiments were designed to investigate the equilibrium of the system at varying parameters of which the level of fluoride addition, the ratio of calcium to magnesium, and the identity of the soluble fluoride was reported. In all of the instances the process showed high selectivity towards calcium and magnesium over the base metals. The experiments proofed the process to have a higher affinity towards the removal of magnesium at compositions where the molar ratio of calcium to magnesium was higher than 1:3. It is often the case that the calcium to magnesium ratio is in the region of 1: 10. From this it follows that the fluoride addition has to be stoichiometric or greater for calcium and magnesium combined, if the calcium is to be precipitated. This was demonstrated as well. On the identity of the soluble fluoride hydrogen fluoride was compared to ammonium fluoride, of which the latter was found to be preferred."

Jan 1, 2003

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By T. N. Aleksandrova, A. V. Afanasova

"The research is aimed at solving the problem of enrichment of sulphide ores, counting for more than 40% of the reserves in Russia. The aim of the research is to develop and scientifically substantiate the scheme for processing this type of ores in order to extract fine-dispersed noble metal particles (FNMP). In this work samples of sulfide carbonaceous ore and flotation concentrates were analyzed using complex precision methods of analysis: electron microscopy, spectral analysis with induction plasma, complex thermogravimetric analyzes, etc. Data on the composition of the organic constituent of the samples were obtained with the usage of complex thermogravimetric analysis. The presence of various types of kerogen and bitumen has been established. Experimental studies on the coarsening of FNMP from the initial ore and flotation concentrates using electromagnetic radiation have shown the effectiveness of this coalescence method. The data on the elemental composition of the samples and the amount of FNMP were obtained. Thus, studies on the extraction of FNMP from carbon sulphide ore have shown the possibility of effective usage of combination of electromagnetic action and classical enrichment methods to extract fine particles of noble metals. INTRODUCTION Due to the depletion of free-milling raw materials the involvement of new types of deposits is the strategy of developing mining industry of Russia. The black shale raw materials show interest as a non-traditional source of precious metals since its genetic and positional gold-carbon connection. Muruntau, Sukhoi Log, Bakyrchik, Natalkinsky, Nezhdaninskoye, Olimpiadinsky, Homsen and others are the examples of well-known deposits of the black shale formation [1]. In fact the main gold-dispersed regions of Russia are composed of black-shale strata. Review of literature [2-5] shows that in recent years in almost all deposits of the black shale formation metals of the platinum group (PGM) were detected that significantly increases their practical importance."

Jan 1, 2018

By Brian Hart, Stamen Dimov

"In refractory ores, a substantial part of the gold content may be present as a sub-microscopic component within the mineral matrix of the various carriers. This type of gold may be present as finely disseminated colloidal size gold particles (<0.5µm) or as a solid solution within the sulphide mineral matrix. Such ores are not amenable to gold recovery by direct cyanidation. In order to liberate the sub-microscopic gold, the ore has to be oxidized before being subjected to gold cyanidation and extraction. Autoclave pressure oxidation (AC POX) of the sulphide ore and subsequent cyanidation is a common technology used to liberate the gold in such refractory ores. The additional presence of active carbonaceous matter in such ores (double refractory ores) represents another major obstacle for efficient gold recovery during the process of pressure oxidation and cyanidation. This carbonaceous matter (c-matter) can adversely affect the gold recovery due to its ability to adsorb, or pre-grob gold from the cyanide solution. Advanced micro-beam analytical techniques such as Dynamic Secondary Ion Mass Spectrometry (D-SIMS) and Time-of-Flight Secondary Ion Mass Spectrometry (TOF-SIMS) have become powerful tools for characterization of different forms and carriers of gold for the needs of the mineral processing industry. Major advantages of these techniques are related to their ability to analyze individual mineral particles and provide quantitative analysis with detection limits in the low ppm/ppb concentration range. This paper describes various micro-beam techniques and procedures implemented at Surface Science Western (SSW) for quantification and characterization of the sub-microscopic gold and the preg-robbed surface gold as part of full gold deportment studies in feeds and process stream products."

Jan 1, 2014

By D. Saramak

Investigations over the application of hybrid comminution circuits with the High-Pressure Grinding Rolls (HPGR), on the main comminution stage on the basis of the lime and cement industry, were presented in the paper. Two crushing circuits were investigated, the first HPGR-based and the other one, with conventional jaw crusher. The results presented in the article confirm that hybrid comminution circuits with the application of HPGR are innovative ones, and they assure achieving the technological and economic competitiveness in the mineral raw materials processing industry. They are much more favorable in terms of the final product fineness and capacity but insignificantly less effective about the unit energy consumption. Technological performance of conventional crushing circuit and HPGR-based one were also compared in lab scale. The circuit with HPGR application gives finer products both on crushing and grinding stages. The average particle size reduction obtained in HPGR-based circuit is as much as twice greater, comparing to the conventional crushing devices. Keywords: comminution, HPGR technology

Sep 1, 2012

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By Braulio Fernández, Gonzalo Montes-Atenas

The mechanisms taking place during the leaching of chalcopyrite when it is in contact with other sulphide minerals, particularly pyrite, is still a matter not fully solved. The GalvanoxTM process has been suggested as a technical solution to extract copper from chalcopyrite at commercial level inhibiting passivation phenomena widely reported in the field of hydrometallurgy. Although there are some rules of thumb to implement the process in fully flooded stirred conditions such as the optimum pyrite/chalcopyrite mass ratio should range between 2 and 4, among others; not many research studies have been focused on studying the effect of the surface contact area between chalcopyrite and pyrite to reach best copper extraction conditions. The aim of this research work is to determine the effect of the mass and surface area ratio between the minerals and the surface area of each of the mineral species effectively exposed to the leaching solution. Different particle size distributions of pure pyrite and chalcopyrite were contacted in a small column and subjected to leach tests using sulphuric acid in concentrations close those used in industrial leaching processes. The mass and surface area ratios which optimize the extraction of copper were obtained. It was found the best leaching conditions were attained when reducing the particle size distribution of pyrite regardless the particle size distribution of chalcopyrite. Further analysis concerning the impact of this conclusions on large scale operations is presented and discussed.

Jan 1, 2014

By Zhongxue Li, Cuiping Li, Xiaoyun Hu, Yiqing Zhao, Huaying Wang

"Under the auspices of World Federation of Engineering Organizations’ Committee on Engineering and the Environment (WFEO-CEE) and Society for Mining, Metallurgy and Exploration (SME) Task Force on Sustainability and Mining (TFSM), and aimed at helping raise global understanding on and promote capacity building of risk management, this paper presents a framework and prototype of toolbox or knowledge warehouse for facilitating the application of risk analysis, mitigation and management techniques (RAMT) in the mining and minerals sector. The conception, design and implementation of the intended system of knowledge warehouse of risk analysis, mitigation and management techniques (KWoRAMT) are outlined. The system architecture of KWoRAMT is based on a browser/server (B/S) structured platform with web oriented interfaces and composed of data base, knowledge warehouse, searching mechanisms, and risk assessment methodologies. The knowledge sources for KWoRAMT will come from the TFSM expertise and Internet, including laws and regulations, codes of practice, standards, guidelines and best practices. The functions and outcomes of KWoRAMT consist of guided navigations with web links, categorized risk tools, annotated best practices with cases, and integrated risk approaches and solutions based on typical risk methods. Risk categories include those impacting on mine safety, mine occupational health, and mine community environment throughout the whole of mine life cycle from exploration, construction, and exploitation and processing to post-mining closure. Mining associated hazards will be identified and linked by vulnerability onto risk receptors through pathways. Risk management techniques for assessing impacts and consequences of mining induced hazards will be categorized with their pros and cons or strengths and weaknesses. Best practices and significant cases including experiences and lessons with problems, solutions, and recommendations on how solutions would be derived will be illustrated. Integrated risk approaches based upon typical methods will be developed for alternatives and actions."

Jan 1, 2014

By Y. Y. Zhou

This paper introduces the application of CRIMM high-gradient magnetic separator in refinement of feldspar powders as well as the supporting technical outfits needed by the refining process with the high-gradient magnetic separator as main equipment. It could reduce the content of Fe2O3 to 0.03% with a deferrization rate of 85.88% from the feldspar raw ore containing 0.17% Fe2O3by using the above refining technology, producing an ultrapure feldspar product.

Jan 1, 2014

By Han Long, He Fayu, Sun Chuanyao

In global mining sector, when people mention "China Factor", usually they refer to China’s huge demands for mineral commodities, which had been driving the world mining industry into late "Super Circle". Few people pay attention to Chinese research capabilities and resources, which actually grows with Chinese economics in last three decades in such a soaring speed that you can simply feel it by the number of papers and attendees in recent IMPCs. In China, currently there are 33 universities and colleges where mineral processing discipline is established, and more than 20 research institutes dedicated in mineral processing area, with the largest number of students, teachers and researchers in the world. Due to the characteristics of Chinese mineral resources, Chinese researchers have made tremendous efforts on R&D of the process and reagents for those low grade, fine dissemination, and complex minerals resources, such as low grade hematite, diaspore, complex poly-metallic sulphides, as well as those minerals rich in China, including scheelite, cassiterite, and rare earth etc. with a special emphasis on the comprehensive utilization. Those research achievements not only successfully commercialized in China, but also have great potential for international cooperation. With continuation of globalization , Chinese government has been encouraging the international R&D cooperation in various areas at all levels, and the funding mechanism is well established with more 400 projects were sponsored in last year,in which,however, the mineral processing related projects are very few. Considering the fact that a large number of Chinese companies or Chinese capitals investing in the mining sector worldwide, more opportunities for international cooperation in this filed wouldbe emerging and increasing, while the factors like complementary, IP, government policy, system and culture difference still need to be addressed properly.

Jan 1, 2014

By Dilip Kumar Mohanty

In today?s world, Sustainability is the key issue before the mankind. With the ever-increasing population & unimaginable boost in industrial growth to cope up with a steady increase in demand and fast change in life style of a human being, the natural resources are exploited to such an extent that the very existence of living beings in this earth planet is threatened. In such devastating situation, the concept of Sustainability emerges out as a great savior. This concept focuses on minimum/ judicious use of natural resources, thereby preserving the resources for future generation while meeting the bare minimum requirement of the present generation. For an emerging economy like India, Mining and Mineral based industries form the back bone of our economic development. Thus, sustainability of mining and mineral processing industry has a far reaching impact on sustainable economic development of our nation. While at a macro-economic level, we have to strike a balance between economic development vis-à-vis socio-economic & environmental impacts, Industries have to ensure judicious and frugal use of natural resources by making use of energy efficient plants & machineries and adopting befitting technology for reduction & recycling of waste. In the context of the above, it would be interesting to look into the sustainability measures taken up by National Aluminium company (Nalco) at its Crushing & conveying plant at Panchpatmali Bauxite Mine, which is incidentally Asia?s largest Bauxite Mine. In the backdrop of the above stated facts, in this paper the authors make an attempt to bring out the sustainability issues in areas of energy conservation, environmental impact/pollution vis-a-vis mitigation measures adopted in crusher & conveyor plant of Panchpatmali Bauxite Mine & CSR / peripheral developmental activities undertaken by Nalco to mitigate the socio- economic impacts. Keywords: sustainability, energy efficiency, recycle, csr, peripheral development

Sep 1, 2012

By N. Kgabi, F. B. Waanders, E. Vinken, A. Mans

"Mössbauer and SEM identification of the iron mineral phases present in South African coal fractions from the Free State, Gauteng, Mmpumalanga, Natal and Waterberg coal fields, as well as from ash samples from coal used in the Lethabo power plant, containing a large amount of inorganic matter, was conducted. The iron is mainly associated with sulphur in the mineral but the amounts of these and other minerals vary considerably in coals from diverse origins. By means of Mössbauer analyses the iron bearing minerals were identified as pyrite, jarosite, illite and ankerite. In the SEM analyses quartz, associated with various clay minerals was identified with differences in abundance found between the coals from the different locations.The fly ash, produced at the high combustion temperatures in the power plant, gave rise to a spectrum, typical of a glass. SEM analyses showed that agglo- meration of the fly ash was due to the presence of Ca in the coal. The lab. produced fly ash was combusted at temperatures ranging from 200-1 200°C and the pyrite changed partially to hematite and partly into the glass due to the presence of the quarts and the clay minerals. A similar spectrum as the power plant fly ash spectrum was obtained.In the weathering experiments the pyrite changed to a sulphate component in a very short time during air drying."

Jan 1, 2003

By Markus A. Reuter, Bernardete Castro, Antoinette van Schaik, Han Remmerswaal

"INTRODUCTIONThis paper describes the inseparable relation between product design, liberation, and metallurgical recovery in the optimisation of the recycling of passenger vehicles. This is illustrated by the use of an optimisation model that uses among others a material combination matrix based on metallurgical process data, which depicts the consequences of the quality of intermediate recycling products on the metallurgical material recovery and final alloy metal quality. Various simulations will illustrate the effect of changes in product design and hence liberation on the recycling of end-of-life vehicles. Although this paper focuses on cars, the discussion is equally valid for any end-of-life product. Calibration of the model will be discussed with reference to experiments carried out in order to study the optimal recovery of aluminium applications used in passenger vehicles.OPTIMISATION MODEL FOR LINKING DESIGN TO RECYCLINGImproving the efficiency of the material cycle of the car is essential to ensure a sustainable development of our society as well as e.g. to comply with the recycling targets imposed by EU legislation. In the design of the car various materials are combined and connected in many different ways, making up the complex 'mineralogy' of the car and its components, which is changing rapidly and continuously over time. The liberation of materials during shredding plays an important role in the composition (and quality) of the intermediate recycling streams. In order to include the influence of product design (mineralogy), liberation, and particle composition (quality of the intermediate recycling streams) in the optimisation of the recycling of end-of-life vehicles, a systems engineering tool for optimisation of the recycling of end-of-life vehicles was developed, including a liberation model. The optimisation model predicts the recovery rate as a function of product design (in this case a car), liberation, efficiency of the different process steps, economy and legislation based on a developed recycling flow sheet for end-of-life vehicles. Optimisation can only be achieved through the combination of the knowledge areas of product design, shredding, mechanical separation technology linked to pyro- and hydrometallurgy, composing a complex interconnected network of unit operations."

Jan 1, 2003

By N. T. Beukes, W. Banda

Recovery of Co from slag is a recent advancement in the extractive metallurgy of nonferrous metals. In this study a DC arc technology at laboratory scale has been applied to investigate the selective recovery of Co from slag, under three different flux types with an emphasis on influencing the activity of FeOx, SiO2 and CoO in the slag. It is known that reduction of slag by carbon is only up to a certain level after which, the recovery will depend on the chemistry of the slag, hence the need to modify the slag chemistry. Two power settings were employed to induce higher temperatures and aggressive agitation. The results were interpreted by comparing how much Co and Fe was in the slag and alloy. TiO2 reduced the amount of Fe in the product alloy compared to when CaO and CaF2 were used. The change in power did not seem to have had a major effect on the recovery although the amount of material lost to flue dust was more at a higher power rate.

Jan 1, 2003

By Camilo Uribe, Williams Calderón, Gonzalo Montes-Atenas

In industrial hydrometallurgical operations, the leaching process is often implemented via heap or dump leaching operations. During the pile up of these massive amounts particles a porous material is then formed. The manner it is constructed is crucial since it will define the permeability and other parameters determining the flowrate of leaching solution across the material. This study aims to estimate how the unsaturated permeability of the staked porous structure confined in a column-like geometry varies with and without particle size segregation. The piling up will be modeled using the Rocky® software. Different disposals of particle size distributions across the column will be simulated and their effect onto the overall column unsaturated permeability will be estimated. It was found that when the belt speed increased, the particle segregation in the column also increased. This condition is expected to improve the permeability of the porous structure in the column, probably due to the smaller compaction of larger particles when they are located at the base of the column and maintain a suitable porosity to permit leaching flowrates relatively high, suggesting better extraction results. The opposite was observed when small particles were preferentially located at the bottom of the column. These results are expected to provide an insight towards what is the best way to construct heaps and dumps.

Jan 1, 2014

The flotation of nickel sulphide minerals is normally difficult in the presence of serpentine minerals due to the coating of serpentine particles on the nickel mineral surface. To improve the flotation, dispersants such as polyphosphate and carboxy methyl cellulose are normally used to remove the slime coating. However, in the flotation using high ionic strength process water, these dispersants are invalid due to their ionic nature. In this study, a new type of non-ionic dispersants, Pluronic triblock copolymers were examined with an objective of improving the flotation of ultrafine pentlandite (a nickel sulphide mineral) in the presence of lizardite (a serpentine mineral) in saline water. Three Pluronic triblock copolymers varying in solubility and hydrophile-lipophile balance (HLB) values were studied by flotation tests, settling tests and froth measurement. It was found that two of the copolymers improved pentlandite flotation against lizardite, and one copolymer deteriorated the flotation. The effect of Pluronic triblock copolymers on the flotation was actually linked to their dispersibility and foamability, which were governed by their physical properties. The two copolymers with a higher solubility or HLB value produced more stable mineral suspensions and more stable froth in the flotation resulting in better nickel grade and recovery in both rougher and cleaner flotation. Keywords: ultrafine particle, flotation, slime coating, dispersion, saline water, triblock copolymers

Sep 1, 2012

By F. S. Hoseinian, K. Filho, D. Deglon, T. Souza, M. Safari

"This paper investigates the reverse flotation of hematite in three laboratory flotation cells with very different contacting environments. The main objectives are to investigate the recovery of coarse quartz by flotation and fine hematite by entrainment. The laboratory flotation cells used were the mechanical, oscillating grid and pneumatic cells. The effect of froth height and solid concentration were investigated in the mechanical and pneumatic cells. The effect of impeller speed and energy input were investigated in the mechanical and oscillating grid cells. Froth height results show that coarse quartz particle recovery decreases almost linearly with increasing froth height due to increased detachment of coarse quartz particles in the froth. Fine hematite particle recovery also decreases almost linearly with increasing froth height due to decreased water recovery and associated entrainment. Agitation/energy input results show that coarse quartz particle recovery increases with increasing impeller speed to an optimum, after which this decreases dramatically. The increase is due to improved gas dispersion, generation of smaller bubbles and increased bubble-particle collision and attachment. The decrease is due to significantly increased bubble-particle detachment at higher impeller speeds. The recovery of coarse quartz particles in the OGC is higher than that in the mechanical cell with an optimum at a much lower energy input. Solids concentration results show that both mass recovery and water recovery increase with increasing solid concentrations. The pneumatic cell achieves higher mass recoveries and lower water recoveries than those in the mechanical cell at equivalent solids concentrations and operating conditions. INTRODUCTIONFlotation is a selective process for separating different minerals from each other. The flotation separation efficiency depends on the recoveries of the mineral species by both true flotation and entrainment (Neethling and Cilliers 2009; Wang et al. 2015). Both chemical variables and hydrodynamic conditions within the flotation cell affect the recovery and selectivity of the flotation process. Cationic reverse flotation of hematite is a common method for selective separation of quartz from iron ores to produce pellet feed. The presence of coarse quartz particles in the tailings and fine hematite particles in the concentrate are two major challenges in the reverse flotation of hematite (Vieira and Peres 2007)."

Jan 1, 2018

By B. S. Moroney

Elemental distribution varies widely in the ores, minerals and beneficiated products depending on the constituents. Accurate analysis of each element present in various beneficiated products is utmost required to assess the grade in view of zero waste technology. Hence, the suitable methods and instrumental technique is of prime importance as the distribution of various elements differs in the beneficiated products. Conventional classical technique of analysis is absolute and due to this, it has not become obsolete. Besides, it is much needed for making standards for various relative techniques. Instrumental techniques comprising of X-ray fluorescence, Induced Coupled Plasma Analyzer, Carbon-Sulphur Analyzer, Atomic Absorption Spectrometer etc. are important for quick and accurate analysis. However, the selection of these instruments depend on the nature of material to be analyzed. This paper highlights the importance and use of various methods/techniques and instruments involved in the analysis of various ores, minerals and beneficiated products. Keywords: wet classical, x-ray fluorescence, induced coupled plasma analyzer, atomic absorption spectrometer

Sep 1, 2012

By Nóra Schreithofer, Zoltán Jávor, Kari Heiskanen

"One of the challenges the mineral processing industry is facing is caused by the fact that water resources in mining areas are becoming very limited and the cost of water is increasing. The water sources in arid regions often have high salt content. Environmental regulations are forcing plant operations towards completely closing the water cycles within plants. This means that impurities (salts, reagents, ions dissolved from minerals, etc.) accumulate within the circuit that will affect the flotation performance. Water purification can significantly increase the operating costs therefore it should be carefully considered weather the impurities need to be completely removed or is there a tolerable level of impurities that can still be left in the process water without significant deterioration of the flotation performance? Several additional questions arise: what are the tools that help identify what is a tolerable level of impurities? How do the different impurities interact and what is their effect on the process? The effect of frothers on the dynamic properties of air/liquid interface in different size-scales has been extensively studied by the authors in the past. Based on these studies a frother characterization framework was developed that systematically examines the dynamic surface properties of the air/liquid interface in relation to the bubble size. This work can be considered as tool that could be used for the above mentioned purpose. The present study investigates weather the same frother characterization framework can be applied for systems where both frother and different types of salts are present. Nasfroth 240 was used as a frother, in combination with structure-breaker KCl or structure-maker NaCl and CaCl2. Bubble size measurements in laboratory scale mechanical flotation cell and laboratory flotation column and dynamic surface property measurements (dynamic surface tension and dilatational elasticity) were performed. The results highlighted the addition of salt to the frother solutions significantly decrease the bubble size and increase the froth high. The coalescence behavior of bubbles showed correlation between the D32 and ionic strength of salts. The results highlighted that the studied structure maker and structure breaker salts effect the dynamic surface properties in different way."

Jan 1, 2014