Search Documents

By S Lukovic, Robert Briton, Calvin J. Konya

Investigators have reported that charges which are decoupled from the borehole wall produce different fragmentation then those which are fully coupled. The difference in effect could be as a result of energy doss during transmission across the air gap or it could be due to the change in detonation characteristics of the explosive as a result of the change in confinement on the charge during detonation. In order to better understand the phenomena of decoupling, a research project was conducted at the United States Bureau of Mines Station, near Pittsburgh, Pennsylvania. It was decided to use shock and bubble energy tests along with simultaneous velocity measurement to determine the mechanics of decoupling and energy transmission. Two explosives were selected for the test, one dynamite and one water gel. Test results indicated that decoupling could both boost the total energy output of the explosive and that further decoupling would drop the energy output.

Jan 1, 1987

By John C. Brulia

PowerAN is a tradename of Atlas Powder Company for a new line of explosive products comprising blends of emulsion and ANFO in a variety of bulk and packaged grades. The bulk PowerAN grades are either augered or pumped depending upon emulsion content. Augered PowerAN blends contain up to 60% emulsion. Pumped PowerAN grades have an emulsion content of 75% or higher. The blending of PowerAN is usually accomplished at the borehole to satisfy specific borehole conditions. Packaged PowerAN grades are produced in several types of mix plants in diameters of 4" and greater. PowerAN 300 (30% emulsion) and PowerAN 500 (50% emulsion) are the two most popular grades and their chief application is as an economical, high energy replacement for ANFO HD in wet holes. PowerAN combines the cost effectiveness of ANFO with the high performance of emulsions, permitting the blasting engineer to strike an optimum balance between drill pattern expansion and increased productivity according to need.

Jan 1, 1985

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By Braden Lusk, Kyle Perry

Recent events and MSHA actions have resulted in discussion and reevaluation of the practice of sealing abandoned coal mine workings. In the past, MSHA has approved alternative seals based on a pass/fail system that required minimal engineering. Disasters involving fatalities led MSHA to impose higher seal pressure requirements based on research and experiments. Impending new MSHA seal regulations will force manufacturers and industry to obtain a high level of engineering expertise. The expertise necessary is in the field of blast resistant design, which is not easily accessible due to the limited number of experienced individuals within the mining industry.

Jan 1, 2008

By Calvin J. Konya

There have been many different brands of high precision caps introduced on the US market in the last five years. High precision timing definitely effects the performance of the blast. One should be able to optimize fragmentation and minimize environmental effects with the use of high precision caps and selection of the proper time period. The consumer who purchases the caps may not be fully aware of the tolerances in firing times of caps used in the field. This paper will discuss results of field tests of cap tolerances from an independent study conducted by Precision Blasting Services.

Jan 1, 1989

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Don Houston

Vertical crater retreat mining (VCR) requires initiation methods that minimize debris in the borehole. The use of detonating cord and shock tube detonators eliminates debris that could interfere with subsequent loading operations and avoids the cost of using drilling equipment to clear the debris. The explosive must not be sensitive to the strength of detonating cord used, otherwise timing will be affected. “Slicing and Dicing” of product before “Air mailing” down boreholes may facilitate loading, especially in wet holes, and can result in product surrounding the detonating cord. Cord sensitivity testing confirmed that having the detonating cord surrounded by product significantly increases the likelihood of an energetic reaction. Careful formulation and testing, based on a thorough knowledge of the application and the role of ingredients in affecting performance, ensures reliable initiation and avoids cord sensitivity. The use of certain metallic nitrate salts, even in relatively small amounts, was found to significantly increase the cord sensitivity of watergel formulations. Evidence of increasing cord sensitivity includes increasing amounts of damage to product and packaging, to ejection of product from the test pipe, then cracking of the pipe, followed by deflagration then detonation of the product. Predictably, the likelihood of an energetic reaction increases with product temperature, cord strength, and borehole diameter, while it is inversely related to product density.

Jan 1, 2002

By Frank Sames

Where applicable, high production benches can improve efficiency in quarrying. Quality control, geological, cost or other considerations might result in the development of quarry benches higher than 30 m (»100 ft) and sometimes up to 60 m (»200 ft).

Jan 1, 1996

By T N. Hagan

Where explosion energy moves rock from the in-situ to its desired location without considerable assistance from digging and/or hauling equipment, good fragmentation is of minor importance. Maximum displacement must remain uppermost in the mind of the blast design engineer.

Jan 1, 1979

By Melvin A. Sannes

The explosives industry is recognized as one of the most dangerous occupations in the world, yet it is rare to see actual training procedures. As our industry becomes increasingly technical, it is imperative that we train the personnel in OUI industry properly.

Jan 1, 1999

By Donald H. Matthews

The Society of Explosives Engineers is an international organization of over four hundred members involved in the explosives industry, with most members being active in the United States. The regulations imposed by regulatory agencies on the explosives industry have drastic effects far beyond the industry. Since explosives are used in mining, manufacturing, construction, entertainment, and art, all phases of man's activities, including fundamental needs for survival, are affected by how efficient the industry uses explosives. We, as members of SEE, must be sincerely concerned with both the quantity and quality of government regulation, and this paper spells out some of the problems caused by regulations and offers a solution.

Jan 1, 1980

By Josh Campbell

Modern blast engineering involves the use of modern technology to provide more efficient blasts. Through the use of improved measurement techniques more information can be obtained on many of the physical variables of a quarry rock face. By employing this information, a more efficient production shot can be designed and loaded. Along with improvements in production, greater safety and improved environmental impact can be achieved. This paper concerns the employment of modern blast engineering at a granite quarry in the Southeastern United States. The test period extended over a period of approximately six months, and this paper will show the results achieved in that time span.

Jan 1, 1998

By Kenneth K. Eltschlager, Richard R. Brochu

At the International Society of Explosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this committee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same within stated tolerances.

Jan 1, 1999

By Terry Graf, Bill Thompson, John Guenther

SYNCRUDE CANADA LTD.. operates the largest synthetic crude oil production facility in the world. Over 60,000,000 Bank Cubic Metres of oil sand is mined each year from their open pit located in Fort McMurray, Alberta. Despite the extremely cold temperatures encountered during the winter months and the problems associated with frost buildup, SYNCRUDE has continued to operate on a 12 month per year basis. In 1989 SYNCRUDE mine management embarked on a comprehensive Frost Blasting program to improve mine production of their oil sand moving equipment. The following paper will discuss the development of their frost blasting program to its current status.

Jan 1, 1993

By Robert L. Brooks

This paper is intended for companies at all levels of the Explosive Industry and in particular, those that do not have a risk manager. It is strictly informational in nature and no reference is made, or intended towards any existing insurance company or agency.

Jan 1, 1993

By Bharat B. Dhar, M D. Nabinllah, A J. Prakash

The study is an approach made in simulating air overpressures induced by surface blasting from those produced during gallery blasting in the laboratory, and experiments conducted on a portable window with a view to establish the sound pressure Level (SPL) for cracking of window glasspanes.

Jan 1, 1994

By C Deacon, M Jones, P Duniam

Electronic blast timing has been in use around the world since the mid-eighties, and, whilst it has yet to be used commercially by large operations on an ongoing basis, significant inroads have been made in niche areas where tighter control of blasting is required.

Jan 1, 1997

It has been common practice for many years to predict and control underwater blasting effects on the basis of certain simplified theories related to the pressures generated by underwater detonations. Unfortunately, two of the most commonly applied concepts in many instances do not provide an accurate modeling of typical field conditions nor the potential for damage. One of these concepts is that the damage potential is related directly to the peak pressure generated by an underwater detonation, without regard to the time history of the pressure pulse. This belief has led to the widespread use of air bubble curtains to reduce peak pressures, without considering the effect that air curtains have on the time history of the pressure pulse. At times, this procedure can be unwise. The other concept is based on the premise that pressure pulses in solids (such as rock) will always be transmitted to nearby water bodies in agreement with the theories of the transmission of plane waves across normal (perpendicular) boundaries. In reality, such conditions are quite rare.

Jan 1, 1985

By Mike Zimmermann

With the steady decline in the production of dynamites throughout the world, a gap appeared in the market which could only be adequately filled by rigid paper packaged explosives. To fill this need, the Dri-Gel technology, which is the subject of this report, was developed.

Jan 1, 1998

By G Alan Foster

Many complaints generated from blasting operations result from the marked human response to ground transmitted vibrations and air blast effects and so many authorities have considered the regulation of blasting in terms of human response rather than, as previously, in terms of preventing damage to structures.

Jan 1, 1981