Search Documents

By Laxman S. Sundae

A Bureau of Mines investigation was conducted to determine the effect of specimen volume on the apparent tensile strength of disks of St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite. The investigation used a technique developed by the Bureau to determine apparent tensile strength. Because the test specimens were selected without macroscopic defects, that is, cracks, joints, and planes of weakness, the strength variations are solely due to microscopic features. Several replications of each test were performed. Data for each set of specimens were fitted to a power law of the form y = axb, where y = apparent tensile strength, x = specimen volume, and a and b are constants. This power law is essentially a form of Weibull's theory. The average coefficients of correlation for St. Cloud Gray Granodiorite, Lithonia granite, and Rockville granite were 0.85, 0.53, and 0.78, respecitvely. In all cases a decrease in strength with increasing volume was noted; in the extreme case, a decrease of 40 pct was noted with an elevenfold increase in volume. The decrease in strength with increasing specimen volume is explained in terms of Weibull's theory.

Jan 1, 1974

By T. N. Williamson

Most U.S. coal production is bituminous coal. Some 90% of current production comes from a geographical area enclosed in a circle with a 300 mile radius and its center at about Huntington, West Virginia. There are important underground coal production areas in the western parts of the United States as well. Most U.S. coal production comes from fairly level seams, many of which pitch rather uniformly only a few feet per mile. Usually there will be several overlying seams of varying thicknesses, separated by several tens of feet. Fig. 1. 1. Seams have minor local undulations but these? are small enough not to be a major consideration in a horizontal drilling research program.

Jan 1, 1970

By Terry J. Close

U.S. Bureau of Mines personnel studied the 33,900-acre Silver Peak Range North Wilderness Study Area (NV-060-338), in order to evaluate its identified mineral resources. The area studied lies between the towns of Silver Peak and Dyer, about 40 miles southwest of Tonopah, in Esmeralda County, Nevada. There are no producing mines in the area studied. However, development of Sunshine Mining Company?s Sixteen-to-One silver-gold mine, located in the Silver Peak mining district near the eastern edge of the study area in the early 19801s, has stimulated recent interest. The Sunshine Mining Company claimed two sites within the study area in 1985. Also, Intermountain Resources, Incorporated, located a group of claims at a prospect along the west side of the study area in the Dyer mining district, and in 1986, began drilling. Other claimants are holding two other claim groups by assessment. At the five currently (1987) held sites, precious metals occurrences are being investigated. There are no patented mining claims or mineral leases in the study area.

Jan 1, 1987

By C. Richard Groves

As the level of technology applied in the electrical measurement, control, and display portions of mine hoist systems continues to advance, the issues and concerns associated with the ramifications of the application of microprocessor technology on the safety-related aspects of these systems become paramount. This report, in part tutorial, addresses several aspects of these concerns. Beginning with discussions of microprocessor-based system architectures, the report addresses some existing and anticipated uses of this technology in mine hoist systems and discusses safety related considerations associated with the areas of data derivation; control and display panels; and system reliability issues. The report concludes with electrical maintenance and inspection considerations associated with the safety assurance of microprocessor based mine hoist systems.

Jan 1, 1986

By R. Newman

An inexpensive slow-speed data acquisition system has been adapted to digitally record multiple parameters simultaneously at intervals of 15 seconds. The system was built for use with standard soils testing equipment to automatically record load and displacement parameters at predetermined instants in time. Simultaneous readout is achieved by the use of special signal conditioner and sample-and-hold circuits which read the multiple signals simultaneously and hold them until the slow acting system can print out. Three channels of a 10-channel system have been converted and found to operate successfully during a series of direct shear tests. A unique feature of the system, which significantly reduced its cost, is the power supply units. Dummy circuits are used to maintain a constant power demand during sampling) thus eliminating the need for a costly power supply with rapid response characteristics. The entire system, having an overall accuracy of 0.25 percent, was put in operation for a cost under $2,500.

Jan 1, 1970

By C. G. Maier

Relatively infrequent use by metallurgists of the term "sponge chromium" as contrasted to more than occasional reference to "sponge iron" may be ascribed to the fact that the former material is not a commercial product, while the latter has been known and used, at least in one form (Swedish sponge iron), for several decades. It is doubtful whether a true sponge chromium ever has been prepared heretofore in the laboratory by more than one or two investigators. Nature presents a much. more difficult problem to the investigator endeavoring to make sponge chromium than pertains to the production of more easily reducible elements such as iron or nickel. Recent widespread interest among metallurgists in the possibilities of powder metallurgy is ample incentive to explore the feasibility of producing pure chromium metal in finely divided form. The shift in terminology of this statement from "sponge" to the "finely divided form" is deliberate in emphasis of distinction between terms that occasionally have been used loosely. It would seem desirable that a uniform usage descriptive of finely divided metals be adopted. While to some it might seem preferable that the terra "powdered" metal be reserved for a finely divided form produced by mechanical means, as, for example, chromium produced by the mechanical comminution of electrolytic sheets or flakes, current usage of the term "powder metallurgy' involves no distinction as to source type of material. It is usually accepted, however, that a sponge metal is one reduced from oxide or other combined form at temperatures below the melting point of metal or oxide so that the particles of metal are pseudomorphic, at least macroscopically, with the source material, and, in consequence of the loss of material without change of external shape of the particles necessarily have an open, porous, or "spongy" structure.

Jan 1, 1942

By John W. Cole

The Bureau of Mines conducted a trenching and sampling project during 1947 on the tungsten-rich granodiorite that outcrops in Henderson Gulch, Montana. During the course of this investigation, interest was attracted to the Sunrise copper-gold mine in metamorphosed limestone in the north slope of the gulch. The mine was examined by S. H. Lorain, Chief, Mining Division, Albany Branch, in May 1948. A trenching and drilling program was recommended to develop a parallel vein indicated by outcrops to lie below the principal productive Queen vein. In the meantime, the Queen Mining Syndicate initiated a trenching program that exposed high-grade lead-copper-silver-gold ore in a nearly vertical vein that strikes N. 600 E. to east. A core-drilling program to develop this vein was initiated in September 1948. This report presents the factual data obtained from the trenching and drilling operations. The Sunrise mine was discovered about 1890. Production has been estimated to be $120,000 in gold from 40,000 tons of ore mined during the period 1892-1903. The tailing from this operation was treated by cyanidation in 1912, with a reported recovery of $3.50 to $4.00 a ton from 15,000 tons of material. Subsequent production of sulfide ore was 7,396 tons treated by smelting, with recovery of 1,569.42 ounces of gold, 10,003 ounces of silver, 352,899 pounds of copper, and 354 pounds of lead.

Jan 1, 1950

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to considerable expense in testing such coals as may be available. In general it will

Jan 1, 1942

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By M. Kawahata

Methane sensors using principle of catalytic oxidation of methane are employed for determination of methane content in ambient air of coal mines. Certain foreign gases or vapors in the air poison the catalyst of the sensor effecting the sensor's response. After literature search of poison compounds of Pt and Pd oxidation catalyst, experimental studies of catalyst poison kinetics were made for three siloxane compounds, tributyl-phosphate, monobromotrifluoromethane, and hydrogen sulfide, selected as poison vapors. Concentration range of the poison vapors was varied in a range from 3000 to 0.1 ppb (v/v). Three siloxane vapors produced strong catalyst poison effect, followed by tributylphosphate, hydrogen sulfide and monobromotrifluoromethane for the high concentration level of the poison vapors. The poison effects are influenced significantly by concentration of the vapors. Threshold poison vapor concentrations where effect of the poison vapors on the sensor is minimal were determined experimentally. Experimental studies were made further for prevention method of catalyst poison by adsorption techniques. Use of activated carbon cloth inserted on the sensor's head prevented catalyst poisoning efficiently.

Jan 1, 1981

By J. R. Thoenen

This circular is the third of a series summarizing the technical problems involved in the production and preparation of sand and gravel. The first, Information Circular 6668, published in December 1932, discussed the problems involved in prospecting and exploration. The second, Information Circular 6689 (March 1933), dealt with the development of gravel deposits. This is part I of a paper designed to present a study of problems arising in the excavation of sand and revel and their delivery to the treatment plant. Other circulars are planned which will discuss preparation of the material for market, plant storage, and miscellaneous subject. Definitions For the purpose of this circular, excavation is defined as the recovery of sand and gravel from developed natural deposits and their delivery to a plant for market preparation.

Jan 1, 1934

By Janet Torma-Krajewski

Job tasks that involve exposure to work-related musculoskeletal disorder (WMSD) risk factors may impact both the risk of injury and production downtime. Common WMSD risks factors associated with mining tasks include forceful exertions, awkward postures, repetitive motion, jolting and jarring, forceful gripping, contact stress, and whole body and segmental vibration. Mining environments that expose workers to temperature/humidity extremes, windy conditions, and slippery and uneven walking surfaces also contribute to injury risk. National Institute for Occupational Safety and Health (NIOSH) researchers worked with powder crew members from the Bridger Coal Company to identify and rank routine work tasks based on perceived exposure to WMSD risk factors. This article presents the process followed to identify tasks that workers believed involved the greatest exposure to risk factors and discusses risk reduction strategies. Specifically, the proposed prill truck design changes addressed cab ingress/egress, loading blast holes, and access to the upper deck of the prill truck.

Jan 1, 2009

By J. P. Morris

The Bureau of Mines investigated the mechanics of fuming of iron-carbon melts during top-blowing with oxygen. Melts weighing 45 lb were prepared in an induction furnace and blown with oxygen by means of water-cooled lances. The rate of fuming was measured and correlated with the operating variables. The data showed that the primary cause of fuming was a boil at the bath surface in the impingement zone of the oxygen jet. Nucleation of the carbon monoxide bubbles producing the boil was apparently brought about by the precipitation of an oxide phase. The actual fuming mechanism involved partial oxidation and vaporization of bubble films and fine metal spray generated by the bursting of the bubbles. Bubbles that formed outside the impingement zone produced little fume. The distribution of trace elements between the metal and fume strongly indicated that the fume contained fine spray particles as well as particles that had condensed from vapor. The rate of fuming was found to be proportional to the carbon content of the metal) the concentration of oxygen in the jet) and the bath temperature) provided that a continuous boil occurred. In the absence of a boil) very little fume was produced.

Jan 1, 1967

By W. C. Hudson

"Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2Si05) and are used in the ceramic industry for the manufacture of high-grade refractories. ""Natural sillimanite with added corundum or other alumina to just short of mullite 2SiO2) proportions is unequalled for jobs where strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags is desired. High-grade porcelain ware also requires these minerals.""At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite has given economic preference to kyanite or andalusite for special refractories and high-grade porcelain ware.""3/The possible economic value of the sillimanite schist in the piedmont Plateau was first recognized by Dr. L. L. Smith, of the University of South Carolina, who published an article in the Engineering and Mining Journal, August 1943, on an occurrence of sillimanite schist in South Carolina.The Bureau of Mines was interested in developing a large source of sillimanite to relieve the shortage of high-grade refractories, and initiated a project to locate the ore-bearing areas in Georgia and South Carolina and to develop the most favorable ones.Two hundred and seventy-eight outcrops of sillimanite-bearing schists were found by a Bureau of Mines engineer.4/ The schist occurs irregularly throughout a belt extending from Talbot County, Georgia; to Spartanburg County, South Carolina, about 220•miIes long and approximately 15 miles in maximum width. The Bureau drilled four areas of the more coarsely crystallized schist in Georgia and South Carolina:In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon; chief; conducts preliminary examinations, performs the actual exploratory work; and prepares the final report. The Metallurgical Branch;.R. G. Knickerbocker; chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Sep 1, 1946

By Gary P. Sames

Shale roof deterioration in coal mines. caused by ventilation air humidity fluctuations, is a common ground control problem. Shale roof deterioration often results in increased accidents, decreased production, inadequate ventilation, and increasing operating costs in maintaining haulage roads and airways. The results of Bureau of Mines research indicate that air tempering entries are an effective method of controlling deterioration prone shales. Some of the conclusions and recommendations drawn from Bureau research include (1) moisture sensitive shales will react adversely to moisture gains and losses, (2) the majority effect of specific humidity fluctuations can be concentrated in and absorbed by tempering entries, (3) tempering entry panels should be located as near to the main intake as possible, (4) tempering panels should be designed for a conservative recovery and provide a minimum of 20-to 30-min air residence time, (5) ventilation and escapeway requirements must be considered early in panel design, and (6) an efficient support and sealant plan can increase the life expectancy of a tempering panel.

Jan 1, 1985

By Pedro Lilienfeld

This report describes a program to develop, design, fabricate and subject to environmental testing three prototype collection-sensing devices of an eventual mining-machine mounted automated monitor for the measurement of the respirable fraction of coal mine dust to determine both short-term as well as average mass concentrations over typical 8-hour shifts. The design of this instrument is based on collection by filtration and mass sensing by beta-radiation attenuation. The emphasis of this development program was to evolve a rugged, stable and reliable collection-detection head compatible with the environment to which An eventual monitor will be subjected. Laboratory testing of this prototype instrument was performed over a representative range of temperature, humidity, dust concentration and composition, shock and vibration. The results of this testing program indicated that the operation of the prototype version His compatible with these environmental conditions and that further development of this configuration into a field operational device is justified.

Jan 1, 1977

An examination of the Census of Fatal Occupational Injuries (CFOI) data for the period 1992-1995 shows that 659 fatalities occurred in the mining industry as defined by the SIC. Oil and gas accounted for slightly more than one-half of all fatalities (figure 1-1). The coal industry had the highest fatality rate for the 4-year period, with 35.6 deaths per 100,000 full-time workers, followed by metal (23.1 per 100,000), oil and gas (23.1 per 100,000), and nonmetal (20.1 per 100,000). The fatality rate for all U. S. industries during this same period was 5.1 per 100,000 full-time workers. Figure 1-2 compares the fatal injury rates by year for the four major industry sectors of mining to the fatality rate for all industries combined. Figure 1-3 compares age-specific fatality rates in the mining industry to those seen for U. S. industry as a whole. Fatality rates for all industries combined were lowest for young workers and steadily increased in relation to workers' ages. In the mining industry, fatality rates by age group show a U-shaped curve. Young workers under 20 years of age had the highest injury rate (54.6 per 100,000), followed by workers aged 20-24 (50.8 per 100,000) and workers over age 65 (37.7 per 100,000). Table 1-1 shows the distribution of injuries by type of injury event. The mining industry, in comparison with all industries, had a considerably larger proportion of fatalities classified as caught in or crushed by collapsing materials (9.1% and 1.9%, respectively) and fires and explosions (10.0% and 3.1%, respectively). Transportation events comprised the largest proportion of fatal injuries in both the mining industry and all industries. Within the mining industry only, transportation accounted for the largest proportion of fatalities in all mining sectors except coal. A more detailed examination of the transportation events within the mining industry showed that highway incidents (50.5%) were the most common, followed by nonhighway incidents (22.2%), pedestrian incidents (10.6%), and those incurred during rail, water, and air transport (15.7%). Incidents involving caught in or crushed by collapsing materials comprised a higher percentage of injuries in the coal and metal sectors, while fall-from-height incidents were more frequent in the oil and gas sector. The classification system used in CFOI for type of injury event is not compatible with any variables contained in the MSHA data; therefore, direct comparisons are not attempted. [ ]

Jan 5, 2000

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939

By Clifford B. Farris

The natural cementation strength of retorted oil shale is the focus of this investigation. The optimum retorting temperature and residence time to obtain natural cementation strength in retorted Green River oil shale from western Colorado were determined as follows: [Optimum Conditions for Natural Cementation Maximum Residence Obtained Retorting Time at Compressive Mode of Temperature Temperature Strength' Retorting °F °C hr psikg/cm-2 Direct 1,520 822 2.0 270 19.0 Indirect 1,530 832 2.9 325 22.8] 1 Scattered samples were tested at strengths as high as 463 psi (32.6 k /cm 2) (Run 8, indirect mode) and 406 psi (28.5 kg/cm2) (Run 48, direct mode), but these high strengths were not confirmed by nearby tests. Minus 0.5-inch (1.3-cm) Green River oil shale was heated in a differential retort under conditions simulating potential full-scale retorting processes. The variables investigated were retorting temperature, residence time, retorting mode, and shale grade. Samples of the retorted Green River oil shale were moistened to optimum plus 2% (25%) moisture, compacted to 95% Proctor density, sealed and cured at 100°F (38° C) for up to 40 days. Lower curing temperatures, which are likely in the field, would probably result in significantly slower development of cementation strength, and might lower the ultimate strength developed. However, these effects were not studied in this project. The cured samples were tested for compressive strength, and correlative equations were developed for the increase of compressive strength with curing time as a function of retorting temperatures and residence time. Petrographic analysis indicated that the cementing mechanisms may be the interlocking growth of acicular hydrated calcium aluminum sulfate crystals between the contacts of retorted shale fragments. Samples of the retorted shale were also tested for optimum Proctor density and moisture. Permeability and quality of the leachate of shale from typical runs were determined. The effect of use of retort rather than tap water on compressive strength and leachate after curing was determined. The retorted shale effectively filtered several mineral constituents from the retort water.

Jan 1, 1979

By NIOSH Publication

In 2004, a total of 7,074 sand and gravel mining operations reported employment to the Mine Safety and Health Administration (MSHA).

Sep 1, 2007