Search Documents

By A. C. Fieldner

"INTRODUCTION In a previous report3 prepared for the American Gas Association, the influence of washing coal on coke properties and on gas and by-product yields was discussed on the basis of answers to questionnaires sent to coke-oven superintendents and a review of the literature on the subject. This review indicated that the elimination of free impurities by cleaning coal improved coke quality by (a) reducing ash and sulphur, (b) decreasing clinker trouble in burning the coke, (c) diminishing cross fractures in the coke, resulting in greater resistance to breakage on handling, and less small coke and breeze, and (d) greater uniformity in chemical composition and physical properties of coke. Washing also reduced the sulphur in coke and gas and increased the yield of gas and by-products per ton of dry coal charged.This paper is supplementary to the previous report and presents some experimental data obtained with Pittsburgh bed coal from Pennsylvania and Mary Lee bed coal from Alabama.ACKNOWLEDGMENTSGrateful acknowledgment is made to F. J. Pfluke, of the Rochester Gas and Electric Cc., of Rochester, N. Y., for the plant test data on screened lump and washed coal; and to Ray W. Arms, Manager of the Coal Cleaning Department, of Roberts & Schaefer Co., of Chicago, for the data on effect of air cleaning."

May 1, 1931

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSS systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

Reduce the respirable dust exposure of the roof-bolter operator when downwind of the continuous miner, particularly in mines where respirable dust standards are more stringent because of silica in the respirable dust. Dust Sources If roof-bolter dust levels are excessive, the bolter dust collector should first be checked to ensure that it is operating properly. (Technology News No. 219 provides information on how to spot and repair bolter dust collector problems). If the roof-bolter dust collector is operating properly and dust levels are still excessive, then the source is most likely a continuous mining machine operating upwind. In many sections, the roof-bolter operator must work on the return side of the continuous miner during part of the production cycle. In three-entry longwall developments with single split ventilation, this may happen as much as one-third of the time. Factors which pro-mote high quartz dust exposure are:

Jan 1, 1985

By David C. Uhrin

Two improved methods have been developed to transfer microfilmed mine maps to suitable base maps showing surface features. The methods provide for (1) positioning and orienting maps; (2) merging adjacent maps; and (3) plotting maps at a common scale. One method produces an overlay mosaic of mine maps using an Integrated camera-processor. This photographic method shows the details of mine workings and is most useful for specific limited-area projects. In the second method, outlines of mine maps are digitized, manipulated, and plotted as overlays using a computer. This computer method can plot mine outlines and spatially index large numbers of microfilmed maps. Microfilmed mine maps used in this Bureau of Mines study are on file in the Mine Map Repository of the Eastern Field Operations Center. The base maps are U.S. Geological Survey 7.5-minute topographic maps. The demonstration area is located in the New Kensington East and West quadrangles, Pennsylvania.

Jan 1, 1977

By Don] [Hinkle

Unable to Load

Jan 1, 1977

By C. H. Manney

This report deals with the feasibility of the use of vocoders as an integral part of a mine electromagnetic voice communication system. Limitations imposed by the nature of the transmission path, background noise and equipment are examined. Some properties of vocoders and apparent advantages of the use of vocoders in a mine communication are discussed. The conclusion is reached that the man-made noise level will ultimately determine the workability of such a system.

Jan 1, 1972

By Donald F. Reed

Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasechatch and Weewoka, both in the; vicinity of Wintorboro, 50 miles east of Birmingham. The deposits were investigated by the Bureau of Mines in 1945 and 1944. Approximately 15,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.

Jan 1, 1949

By S. M. Runke

"During the past three years the Bureau of Mines has carried on an extensive research program at the Rolla Laboratory for the beneficiation of low-grade Arkansas baixites by ore dressing methods. As a result of this study a 50-ton pilot mill was designed and constructed at Bauxite, Arkansas, by the Bureau to continue the investigation on a semi-commercial scale. The built both to reduce the experimental work to practice and to obtain operating data that cannot be determined by laboratory or small scaleTen samples of bauxitic material were mined and stockpiled at the plant site to ensure an ample supply of material for milling in the pilot plant. These samples were obtained from various bauxite deposits in Saline and Pulaski Counties, Arkansas. The deposits were selected as typical of a wide range of bauxitic material which would necessitate treatment under different conditions and by various concentration methods. All of the samples contained a higher silica content than permissible in Bayer-grade bauxite and several contained so much iron oxide that the available alumina content of the ore was mate¬rially lowered. From data obtained by milling operations on these ten samples, milling characterietics of most of the ores in the district should be predictable. This paper summarizes the results obtained in the laboratory testing of representative samples of each stock pile, and the results of small scale continuous testing of the composite sample of the ten stock piles in the gravity-flotation pilot plant at the Rolla Laboratory."

Aug 1, 1946

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSWA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. metallic mining workforce from March through September 1986. Similar reports have been published for the stone, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By S. K. Mathur

This report identifies all the possible activities, variables and factors that contribute to the surface subsidence process over room and pillar workings. These factors are responsible for mine instability and collapse that ultimately transforms into surface subsidence. Such a failure mechanism is initiated by the failure of the mine floor bed and or the failure of the pillars or the failure of the roof after second mining, which eventually brings down the roof. The individual responses of the pillar, floor and roof rocks to the mining induced stresses and the complex interaction between these components can't be attributable to any single factor. Also, no attempt has been made to quantify the significance of each of these factors and relate to the ground subsidence due to the lack of field data. The discussion here is centered primarily on the first mining though second mining is mentioned very briefly,

Jan 1, 1982

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

This chapter analyses the parameters influencing initial design of communication systems, for new mines and upgrading existing systems. Paragraph 5.2 outlines those variables that must be taken into account during the design stages of a new wired phone system. Recommended features, general requirements, and how they can be implemented are treated in this section. Paragraph 5.3 describes ways of improving or extending the range of trolley carrier phone systems and pager phone systems already installed in the mine. 5.2 New Phone System Design The task of designing an adequate communication, control, and monitoring system for an underground mine must be addressed on a system basis. In addition to insuring that effective voice communication is established, any new system should take into account present and future requirements of remote control and monitoring functions. Chapter 4 illustrated the drastic savings in response time that can be realized when remote control and monitoring are integrated into the overall communication system. The importance of including control and monitoring in the overall design plan for any system cannot be overemphasized. Because each mine is unique, and thus usually has its own special operating characteristics and communication requirements, there is no such thing as "the one best system" to meet the requirements of all mines. The optimum communication, control, and monitoring system for a mine must be one that has been tailored to meet the special requirements of that particular mine. Factors that must be considered during system design include- a. Type of mine and mining methods (low- or high-seam coal, deep hardrock mine, stope caving, longwall, room and pillar, etc.). b. Maximum number of working sections. c. Expected mine growth rate and eventual maximum size. d. Haulage methods (tracked trolley, diesel, belt, etc.). e. Underground power distribution system (dc, ac, or both). f. Features desired (two-way radio paging, private line capability for emergency use, etc.). g. Redundant or backup systems for use during outages of the normal system. Although no two mines are alike, the following items have been established as the main characteristics desired for any underground communication system: 1. Multiple Communication Paths to Outside--the objective here is to give all telephones a second method of communicating with the surface. 2. Audible Emergency Signaling--the communication system provides the main means of alerting miners during emergencies. The system should include means to broadcast distinct audible signals for emergency signaling. Initiation of these signals should probably be controlled from. a central outside point, such as a surface control room. 3. Emergency Override--provisions should be included to permit any conversation to be overridden with emergency communication. 4. Selective Area Page--as mines grow larger it is apparent that the entire telephone system paging mode need not be activated each time a call is initiated. When the general area of a

Jan 1, 1984

By Forrest T. Moyer

The safety record of the coal-mining industry in 1968 worsened appreciably .in fatality experience but was slightly better in nonfatal-injury experience. Work fatalities in 1968 totaled 311 and occurred at a frequency rate of 1.33 per million man-hours or worktime. The fatality total was 89 higher, and the rate of occurrence was 45 percent higher than the corresponding figures of 222 fatal injuries with a frequency rate of 0.92 in 1967. The worsened fatality record in 1968 resulted primarily from two major disasters (a single accident which results in the death of five men or more) which killed 87 men, nine in one and 78 in the second. The total of 9,639 nonfatal injuries was the lowest annual figure in complete records back to 1930. The frequency rate of 41.12 nonfatal injuries per million man-hours of worktime for 1968 was the second lowest annual rate of occurrence. The severity rate of all injuries, 10,513 days lost or charged per million man-hours, and the average severity, 248 days lost per injury, in 1968 were the worst annual data in the series started in 1944. Total worktime of 234.4 million man-hours and coal output of 553.3 million tons in 1968 were, respectively, 3 and 1 per- cent lower than in 1967.

Jan 1, 1972

By Fraser M. Walsh

The objective of this program was to determine by laboratory experiments the kinetics and mechanics of the reactions that produce acid in coal mine drainage. The program was divided into three phases: In Phase I, five coil mines, representative of Appalachian coal mines, were chosen for sampling and an experimental design was identified suited to accomplish the program objectives. In Phase II, the five mines were sampled and test protocols applied. The results showed most pyrite weathering to be based on oxidation in the presence of water. Iron bacteria, especially Thiobacillus ferrooxidans, catalyzed the rate of pyrite weathering by a factor of three. An increase in initial iron concentration in a system that modeled the nine environment acted to inhibit bacterial catalysis of weathering. In Phase III, five tailings piles were sampled and the material obtained was used to evaluate this method of bacterial catalysis inhibition. The evaluation verified method effectiveness; inhibition of over 80% of the release of weathering products was observed.

Jan 1, 1982

By Zsuzsanna Zborovszky

A circuit is considered intrinsically safe when any spark or thermal effect produced normally (that is, by operating the equipment in its correct operational manner to fulfill its purpose) or accidentally (caused by short circuit, earth fault, defective components, breaking the wiring, etc.) is incapable under prescribed test conditions of causing ignition of a prescribed gas mixture. The test conditions and gas mixture should be at least as hazardous as the true parameters of the environment where the circuit will be operated. According to present practices, the question of whether or not a circuit is intrinsically safe is decided upon experimentally. The circuit is inspected first for mechanical soundness and a survey is made to determine what faults should be considered as probable. Then the individual branches are connected, in sequence, to a test apparatus called 'breakflash" which acts as an opening, closing contact and thus draws sparks from the circuit. This test is repeated a given number of times in the presence of the prescribed gas mixture under specified conditions (electrode configurations, gas parameters, etc.). The equipment will be regarded as intrinsically safe if during testing no ignition has occurred.

Jan 1, 1972

By F. S. Crawford

Safety devices and guards are often looked upon as the last word in safety by the men around the shop or large industrial plant . However , thorough knowledge of the details of their jobs and of the dangers attending them are even more important . It should be unnecessary for all men to go through the experience of the first man to meet an unknown danger , but that appears to be about the only way by which many learn . Practically every danger connected with the job around a mine , blast furnace , steel mill , foundry , coke oven , cement mill , or other operation , was encountered for the first time by someone , and if he was fairly fortunate he either got hurt or just missed being injured and lived to tell his " budaies " how it happened; he spread the knowledge of that particular danger . Sometimes , but not often , a man can foresee a danger . If he could always be on guard and remember everything he had ever learned and also know everything that had happened to the other fellow , and then let that knowledge keep him aware of the dangers in his own immediate " job , " so that he would work the safe way for both himself and the other fellow , he would have what safety engineers call " safety consciousness . " Being safety conscious is a fine attribute , as it really means knowing all about one's job . A man who is really safety conscious is one of the best and most efficient workmen in the whole plant . The boss wants men of that kindmen who want to learn and who try to learn every little detail about their jobwhere there is danger of spoiling the heat or getting burned by hot metal in a steel plant or of loading rock instead of coal or ore in a mine . Such men know how to do whatever job they are on easily and with the least amount of hard work and at the same time get it done as quickly as possible with safety . A man who is safety conscious has to nearly all intents and purposes developed eyes in the back of his head , if he is in a big mill where there if something going on all around him . These eyes are not real eyes , but they are what might be termed a sixth sense which he has developed by his experience in the mill as well as in other dangerous work which he may have done before in other plants . There may be occasions when a man's safety consciousness will leave him for just a short time ; this is likely to happen when he is thinking about a quarrel he had with his wife which has not been cleared up happily , or perhaps when he has bought too many things on installment and with sickness at home

Apr 1, 1931

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By M. L. Fenger

This report describes a study of the factors which affect medium voltage (661 - 1000 volts) and high voltage (1001 - 7500 volts) trailing cable couplers for use in underground coal mines to connect trailing rabies. Improvements in quality, dependability, and safety of medium and high voltage couplers are presented in the form of requirements for couplers. The results of an investigation of high voltage trailing cable coupler design and of whether trailing cable couplers must have a metallic shell as required by CFR 30 part 75.805 are presented. Conclusions and recommended research programs are included that describe the present situation and future development approaches.

Jan 1, 1978

By Ben E. Lindsly

The recovery or partial recovery of the oil remaining in oil sands after the usual methods of production have become unprofitable is perhaps the greatest problem in the petroleum industry today. The amount of this oil remaining in the sand is variously estimated by those familiar with the subject to be 25 to 90 per cent of the original content.2 Lewis3 states, "The estimate of 80 to 90 per cent of the oil left underground does not seem incredible."

Jan 1, 1926

By George T. Motock

The author prepared the following report as the result of a trip to Germany in the summer of 1945 for the Technical Industrial Intelligence Commitee Subcommittee on Metals and Minerals. The purpose of this committee, which functions under the Joint Intelligence Committee of the Joint Chiefs of Staff of the United States Armed Forces and of which the Bureau of Mines

Jan 1, 1946