Search Documents

By P. J. McDonough

The Bureau of Mines designed and tested a hardware-software system for measuring on-line corrosion rates of materials in a rod mill in operation. Currents ranging from 10-6 to 10-3 A and potentials in I-mV increments were converted to a digital signal. The digitized data were frequency-modulated and transmitted from a rotating ball mill to an FM receiver, where they were decoded by computer and then processed in real time using assembly language software. This design approach would allow accurate measurement and control of systems where signals of small amplitude and large ranges are present.

Jan 1, 1988

By F. W. Wessel

Manganiferous carbonate slates of the Cuyuna range, which are part of the unoxidized thin-budded iron formation, represent a large potential source of manganese. This report details recent bench-scale research by the Federal Bureau of Mines in applying mineral-dressing techniques to these materials in order to investigate their potential uses. Work outlined in the report was directed toward the production of concentrates usable as iron-blast furnace feed, but an equally important objective might have been to furnish an enriched feed for extractive processes for recovering manganese. Flotation concentrates were prepared that contained 11.1 percent manganese, 27.8 percent iron, and 12.2 percent silica, with recoveries of 73 percent of the manganese and 48 percent of the iron. Calculated analysis for a simulated sinter suggests a product containing 16.0 percent manganese, 40.2 percent iron, and 17.6 percent silica, with 31 percent recovery of the dry weight of the ore. The silica in the flotation concentrates was due to quartz and iron silicates. Substantial quantities of the iron silicates (stilpnomelane and smaller amounts of minnesotaite) were present in the slate, and the need to reject these minerals limited the recovery of iron. The sintered flotation concentrate would be usable as ferruginous manganese ore for iron blast-furnace feed because of its favorable manganese silica ratio. The unsintered flotation concentrates, representing 45 percent of the feed weight and containing manganese enriched in the ratio of 1.6 : 1, also could be used as feed to processes for extracting manganese.

Jan 1, 1961

By D. A. Reynolds, J. D. Davis

"INTRODUDTION Investigations by the Bureau of Mines have shown that the carbonizing properties of splint and bright coals may differ greatly. In a study of 55 coal columns selected from representative coals of the Appalachian region, Sprunk and coworkers 10/ compared various chemical and physical properties of splint and associated bright coals. Carbonization tests in the Fischer retort at 932°F. (500°C.) showed that, except for bright coals of high oxygen content, the coke residue from bright coal was much more swollen and cellular than that from splint. ·with one exception, agglutinating values determined by the Bureau of Mines test, were lower for splint than for associated bright coal.Because sorting of coal in quantity is tedious and time-consuming, separate types have not been carbonized by the Bureau of Mines-American Gas Association (BM-AGA) test, which requires 85- to 200 pound charges. However, this method has been used to determine the carbonizing properties of samples 0f bed layers that are composed largely of either splint or bright coal.4/ In these earlier tests, which were made at high temperatures on layer samples from the Elkhorn bed, Letcher County, Ky., the splint coal yielded more coke than the bright coal, and this coke was slightly stronger than that from the bright coal. The cokes from samples with large proportions of bright coal were more cellular or porous, as were the low-temperature cokes obtained from carbonization of separated samples of bright coal in the Fischer retort."

Apr 1, 1944

By J. W. Paul

A superintendent is one who has the oversight and charge of some organiza- tion or enterprise, with porer of direction. The superintendent of a coal mine is the official who is in general charge of conducting the operation of the nine for the purpose of producing coal; he is accountable to his superiors for all matters that relate to the cost of production and safety in operation, ed under him are all the underground officials and other personnel making up the mine organization. The responsibility of the superintendent covers all the principal phases of mining, purchases of materials, issuance of supplies, accounting, and upkeep of the property and equipriont. In a broad sense, the superintendent must view his job as embraced under four gneral heads: (1) Construction, (2) instruction, (3) supervision; and (4) discipline. The degree of efficiency with which each of these phases of his work is conducted is a measure of the safety factor which the superintendent injects into his job. Injury to workmen and damage to property may be due to neglect of one of these general headings; as for example in the collapse of a scaffold there has been faulty construction which may be found upon investigation to have been the result of faulty instruction or lack of instruction. It may be that the condition of the scaffold was not ascertained in advance of its collapse through faulty supervision, or the discipline of the workmen had been neglected.

Sep 1, 1930

By A. Galaitsis

This report summarizes part of the work performed under the USBM Contract No H0155113, "Noise Abatement of Continuous Mining Machines." It describes the noise source diagnosis of a Jeffrey 120M conveyor and the evaluation of several treatments all conducted in a test facility aboveground. The conveyor noise at the operator's position was gradually reduced from 101.5 to 93 dBA using damping, vibration isolation, sound barriers and smoother discontinuities. The underground performance of the selected treatments will be addressed in Volume II of the report.

Jan 1, 1979

By Martin A. Elliott

The Bureau of Mines began its investigation of the use of Diesel engines underground to provide technical information necessary to assist this development in the United States. It was considered desirable to furnish such assistance because successful European developments/ in this. field had indicated that Diesel mine locomotives might be safer than electric trolley locomotives. The Bureau has recognized for some time the importance of eliminating the hazards associated with underground haulage systems using bare trolley wires. For example, each year 30 to 40 fatalities occur as a result of electrocution by contact with bare trolley wires. In 1943 and 1944, 101 men were killed and extensive property damage occurred as a result of mine fires started by falls of roof grounding the bare trolley wires.

Jan 1, 1948

By D. J. Parker

The ease of ignition and violence of explosion of Utah coal dusts, together with the large volumes of methane given off in some of the mines of the State, made it imperative to abandon obsolete equipment and obviously hazardous practices for up-to-date equipment and safer methods of mining if reasonable progress wore to be attained in fire and explosion prevention. Although much can still be done to improve safety conditions in Utah coal mines, considerable progress has been made in the past 10 years. The fundamentals of such progress include increased use of permissible electrical equipment in gassy mines, closed lights, rock-dusting, more liberal use of water at the face, butter ventilation, permissible explosives fired electrically both within and without the mine, partial inhibition of blasting while the shift is in the mine, 100-percent first-aid training, increased supervision and inspection, and mass safety meetings.

Jan 1, 1935

By W. W. Adams

Lower accident rates were the outstanding feature. of the second annual sand and gravel safety competition conducted in 1930 by the United States Bureau of Mines in cooperation with the National Sand and Gravel Association. Both the frequency and, severity rates for accidents were greatly reduced as compared with those shown by the first year's contest, that for 1929. Three times as many plants were enrolled, and the number of man-hours of work represented wad more than doubled. Seventy-six sand-and-gravel plants, situated in 20 States, participated in the competition, as compared with 26 plants, located in 13 States, in the year before. The number of man-hours of employment, which indicated the amount of exposure to occupational hazards, was 4,915,592 an increase of more than 100 per cent over, the previous year's total of 2.259,572 hours. The frequents of accidents declined from 74.4 per million hours for all plants enrolled in the first year's contest to 42.7 per million man-hours for all plants enrolled in 1930. The accident-severity rate was reduced from 9.7 days of disability per thousand man-hours of exposure in 1929 to 5.9 days of disability per thousand man-hours of exposure in 1930.

Jan 1, 1931

By F. Chen, L. J. Gaydos, L. M. Demers, D. C. Kuhn, S. C. Sun

"In this report, we demonstrate that NF-KB, a ubiquitous transcription factor, plays an essential role in silica-induced inflammatory mediator production in the mouse macrophage cell line RAW 264.7. Compared to the effect of lipopolysaccharide (LPS), silica mediated a stronger activation of NF-KB p50/p50 homodimer at early phase of poststimulation. Furthermore, activation of NF-xB by silica and LPS appears to be mediated by different signal transduction pathways. Both silica and LPS increased mRNA expression in these cells for cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-a and interleukin- I a. This expression was attenuated along with the inhibition of NF-KB activation. It is well documented that exposure of alveolar macrophages to silica can initiate excessive production of inflammatory mediators and cytokines from several early response genes (1-3). At the DNA level, a common structural characteristic of these genes is the presence of one to five NF-lCB binding sequences (KB) in the 5'-flanking region (4-6). In resting cells, NF-KB is retained in the cytoplasm in an inactive form by binding to inhibitory protein known as hcBcx, hcB~. p 105 (precursor of p50) and p 100 (precursor of p52) (7-9). Upon cellular stimulation, these inhibitory proteins are proteolytically degraded or processed by certain proteases, which allows the liberated NF-KB to translocate into the nucleus as an activated form to initiate or regulate early response gene transcription by binding to its consensus element (GGGRNNYYCC)(7).In this report, we demonstrate that silica can efficiently induce NF-lCB activation in RAW 264.7 cells, and that silica displays different characteristic from LPS in the activation of NF-KB, both with respect to NF-KB subtype composition and the signal transduction pathway that leads to the activation of NF-KB. In addition, abrogation of NF-KB activation by inhibiting the protease can dramatically reduce the mRNA expression of cyclooxygenase II, inducible nitric oxide synthase, tumor necrosis factor-ex (TNF-o.) and interleukin-lex (IL-lex). These findings strongly suggest that NF-KB plays an essential role in silica-induced inflammatory mediator production in the monocyte/ macrophage cells."

Dec 1, 1996

By L. D. Wyant

That natural gas-gasoline can be used to advantage as a refrigerant is suggested by the fact that the "make" tanks and other parts of the equipment of gasoline plants frequently become coated with frost. The experiments reported in this paper confirm this assumption and indicate that volatile gasoline can be use used to advantage in many refrigerating plants. The Bureau of Mines is making a study of wax distillates in order to find out why satisfactory lubricating oils and waxes can be made easily from certain crude oils and only with difficulty from others. In the commercial distillation of crude petroleum it is customary to separate the distillates into the following groups: (A) Gasolines and naphthas, (B) Kerosenes, (C) Gas oil, and (D) Wax distillate (consisting mostly of light lubricating oil together with small amounts of paraffin Wax).

Jan 1, 1923

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By G. A. Savanick

The Bureau of Mines has designed, fabricated, and field tested a water jet cutting device capable of perforating nonmetallic well casings for the purpose of completing or stimulating in situ uranium leaching wells. The device is lowered into the wellbore, where it issues a high-velocity water jet that penetrates either a polyvinyl chloride or fiberglass casing, cement, and from 1 to 4 feet into the surrounding uraniferous sandstone. The resulting perforations allow leaching solution to pass between the sandstone and the wellbore. This report describes the water jet perforator, tells how it is used, presents cost data, and discusses the results of laboratory and field tests. The tests were designed to (1) determine the optimum operating conditions for water jet perforation, (2) assess the effects of changes in these conditions, (3) evaluate the performance of the water jet perforator under actual conditions, and (4) compare this method with other methods of well completion. These tests showed that water jet perforation is superior to conventional well completion methods for selectively achieving communication between the well-bore and adjacent sand while maintaining sand control, for restoring permeability lost through wellbore damage, for stimulating poorly performing wells for completing wells with casings that have inside diameters as small as 2 inches, and for extending the effective well diameter.

Jan 1, 1981

By H. C. Miller

For nearly a score of years the American petroleum industry has faced the problem of maintaining its economic structure while oil -producing potentialities greatly exceeded the increasing market demand for oil and its products . However , the combination of maximum civilian demand with rising defense requirements caused an all - time peak in crudeoil production in the latter half of 1941 , with a daily production (as estimated by the Bureau of Mines ) of 4,139,000 barrels in December - an increase of 16 percent over the daily production of 3,573,000 barrels in December 1940. In the event of a long war , a continuing , steady, and adequate supply of petroleum and its products for military and required civilian needs is essential, and the efficiency of recovery of oil from natural underground reservoirs will have to be maximum. Whereas it may not be possible to increase production in some fields , the output from others may have to be drawn at a much faster rate than formerly . More than 10 years ' experience in operating oil fields under proration control has demonstrated to petroleum engineers that some of the efficiency of recovery of oil from reservoir sands and rocks is sacrificed if the oil and gas are withdrawn at too . rapid a rate . As petroleum is an irreplaceable natural resource for which suitable substitutes probably will not be available in desired quantities for many years , any producing method that jeopardizes the quantity of oil that may be recovered from underground reservoirs must be considered at this time of declared war against aggressor nations as conflicting with the best interests of national defense . At best, the efficient recovery of oil is a complex problem . It involves not only a knowledge and application of the fundamentals of fluid flow through porous mediums, but the sources of energy responsible for the movement of oil and gas through reservoir sands and porous rocks to wells must be known to determine the best practices for extracting these hydrocarbons . Reservoir energy is of two kinds - (1 ) water under hydrostatic head underlying the oil in the extraneous parts of the reservoir system and ( 2 ) natural gas under pressure as "free " gas in the reservoir or in solution in the oil . Inasmuch as the efficiency of oil recovery depends largely on the manner in which reservoir energy is used to move oil through reservoir sands and porous rocks to wells , optimum practices for withdrawing the oil cannot be determined until it has been established that the oil in the reservoirs is being forced to wells by an internal gas expansion, by a natural water drive , or by a combination of gas expansion and water drive . There is a fundamental difference in the performance characteristics of gas - expansion and water - drive reservoirs . In a strictly gas - expansion reservoir the energy available to move oil and gas through the porous formations to wells results solely from gas pressure , which is maximum when the reservoir is tapped by the first well . Pressures decline as oil and gas are withdrawn ; consequently, the energy available for moving oil and gas through the oil - bearing formations to wells decreases with production . Curtailing the oil - production rate or shutting in gas - expansion reservoirs entirely will not act to replenish energy previously used in the production of oil and gas ; in their operation , therefore , it is especially important not to waste reservoir energy - the production of oil with high gas : oil ratios will be reflected in lower ultimate recoveries of oil .

Apr 1, 1942

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By W. R. Gilliland, G. W. Jones

"One-phase of the accident prevention program of the Bureau of Mines is the determination of the explosion hazards of various combustible gases and vapors encountered,mining and allied industries and the development of means and methods of eliminating them.Gasoline is foremost among the combustible-liquid's as to quantity used and variety of applications in industry, It is a chief contributor to the causes of fires and explosions, taking an enormous yearly toll in property damage and considerable loss of lives.The results presented in this report evaluate the effect of various gaseous inert substances, which owing to their chemical composition, should be of considerable value in the prevention of gasoline fires and explosions. The substances investigated are as follows: Nitrogen (N2), automobile exhaust gas (85 percent N2 + 15 percent CO2), carbon dioxide(CO2), dichlorodifluoromethane (CCl2F2-Freon-12), trichloremenofluoromethane (CC13F-Freon-11), and dichloromonofluoromethane (CHCl2F-Freon-21).The general term ""gasoline"" designates a combustible liquid of such characteristics as to give satisfactory operation without preheating in spark-ignition-type internal-combustion engine. It comprises a complex hydrocarbon mixture having a limiting distillation range and produced commercially by distilling or ""cracking"" crude petroleum or other various petroleum stocks. Small proportions of other substances may be incorporated in the gasoline to enhance its antiknock properties or operating characteristics in internal-combustion engines and to increase its stability during storage, transportation, and use.It is thus seen that gasoline may have rather wide variations of chemical and physical properties, and it would: appear that the results of any investigation dealing with one particular gasoline might not be applicable to other types. However, as indicated by the results given in this report, the inflammable properties of different gasolines at normal atmospheric temperatures are influenced largely the mars volatile hydrocarbons containing 5, 6, 7 carbon atoms- in the molecule, and that the heavier constituent of higher molecular weight have a minor influence on the inflammable properties at ordinary temperatures."

Apr 1, 1946

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By Kenneth R. Maser

This report describes the development of a system which modifies an existing fly ash-foam remote mine sealing technique to make it capable of impounding water in a fire zone. The modification involves blending equal quantities of fly ash and bentonite to form the bulk of the seal, and blending a thin layer of fly ash and Huron Regulated Set Portland Cement (RSPC) as a coating. The modification replaces the pure fly ash approach, but continues to use a froth foam topping to complete the seal. The modified material system is implemented with minimal complexity by adapting a "Y" connector to the existing delivery system. Each bulk hauler (fly ash and bentonite, or RSPC) will pump into one leg of the 'Y'; and the blending will be controlled by two pinch valves. The development effort has involved an evaluation of potential material systems by using small sample, quarter scale, and full head tests. The small sample tests measured the basic properties of a large number of selected material combinations. Property measurements included capillarity, permeability, shrinkage, and shear strength. As a result of these tests, particular combinations of fly ash-bentonite and fly ash-cement were selected for scale model testing in a 1 /4 scale test facility. These tests simulated, in a scaled manner, the water rise and total head which would be experienced by a seal. The tests indicated that shrinkage in the fly ash-cement combination would always result in leakage; whereas, fly ash-bentonite mixes were impervious to water.

Jan 1, 1974

By J. R. Thoenen

The objective of this circular is threefold: First, to describe briefly the various modes of occurrence of sand and gravel. Second, to emphasize the need for adequate prospect¬ ing and exploration prior to the expenditure of funds for development and plant construction. Third, to describe various methods of prospecting and exploration and their application to the several modes of occurrence of sand and gravel. Sand and gravel may be found in nearly every county or township in the United States. Commercial deposits, however, are by no means so widespread. The introduction of concrete and the consequent impetus given to consumption of gravel and sand aggregates has seriously depleted deposits in some congested areas. Increasing re¬ strictions in the specification requirements for marketing sands and gravels have further narrowed the economic areas. On the other hand, the combination of increasing transportation costs and decreasing selling prices has forced the decentralization of gravel production. As a result smaller, intermittently operated, and widely scattered portable or semiportable unit plants have been encroaching on the territory formerly supplied from centrally located pits with large tr.atment plants. Generally speaking, the small portable plant can not produce any great variety of ma¬ terials to as exacting specifications nor as economically as the large permanent plant.

Dec 1, 1932

By Scott A. Stebbins

This Bureau of Mines publication presents a method for estimating capital and operating costs associated with the exploration, mining, and processing of placer deposits. To ensure representative cost estimates, operational parameters for placering equipment and basic principles of placer mining techniques are detailed.

Jan 1, 1987

By R. Karl Zipf, Z. T. Bieniawski

"Researchers at The Pennsylvania State University are engaged in a project to understand the mechanics of respirable size fragment formation in coal. The project is based on the premise that a thorough understanding of the fundamental mechanics of fine fragment formation may lead to techniques for reduction and better control of coal dust problems in mines. Presently, it is believed that the mode of fracture propagation which can range from pure tensile to pure shear or any mixed mode in between and the loading or displacement rate can influence the amount of respirable size fragments that are generated on new fracture surfaces during the fracture propagation process The essence of any coal cutting process is one of mixed mode fracture propagation. To study the crack propagation process, a unique mixed mode testing rig was designed and fabricated. This rig is capable of applying loads to a prenotched test specimen that range from pure Mode I (tensile mode) to nearly pure Mode II (shear mode) or many mixed mode loading combinations. It is also possible to apply different loading or displacement rates to the test specimen. With this rig, it is possible to create new fracture surfaces via the different fracture modes and under various loading conditions.These new fracture surfaces are examined with a scanning electron microscope (SEM) to characterize the amount of structural damage and respirable size fragment formation that occurs during the fracture process. Initial observations suggest that the amount of fine fragment formation and the new fracture surface appearance is related to the fracture initiation conditions, particularly the fracture mode and the loading rate. Mode II loading and higher loading rates seem to generate more structural damage and respirable size fragment formation that Mode 1 loading at slower rates.With the mixed mode test rig, the mechanics of fracture initiation for a single crack can be controlled to better understand its influence on respirable size fragment formation. Such understanding may lead to methods which characterize the tendency of specific coal seams to produce undesirable fine fragments during the fracture process, or it may lead to rational recommendations and design guidelines or coal mining machines which inherently produce less dust.IntroductionAs part of a larger effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners, researchers at The Pennsylvania State University are engaged in a project to understand the fundamental mechanics of fine fragment formation in coal. This project is part of a com¬prehensive research effort within the Generic Mineral Technology Center for Respirable Dust which is jointly administered by The Pennsylvania State University and West Virginia University.The principal source of the coal dust in underground mining is the cutting operation. The U.S. Bureau of Mines (USBM) and various European research organizations have conducted investigations into the mechanics of coal cutting for many years. These studies of airborne respirable dust (ARD) formation have concentrated on empirical studies of the various cutting parameters and their effect on ARD for¬mation. The parameters study include depth of cut, cutting speed and bit spacing.(1,2) Other studies investigated the effect of symmetric and asymmetric bit wear and various bit geometries and designs (3-5) Roepke(6) summarized the principals of proper coal cutting to minimize dust formation by recommending to ""cut at maximum depth (maximum advance rate) at all times, at minimum RPM, with the fewest possible bits, having the lowest possible included tip angle."" Most coal in the U.S. is mined with the continuous mining machine which inherently cannot meet these design recommendations.(3)It is recognized that respirable size dust particles are formed and/or liberated by a fracture process. One extremely interesting and useful study performed very early in the USBM dust re"

Mar 1, 1989