Search Documents

By Fred D. Wright

Some new equipment for drilling vertical holes, cleaning blast holes, hauling explosives, and conditioning Diesel exhaust gas has been developed. at the Bureau's Experimental Oil-Shale mine near Rifle, Colo, The equipment has application, not only in oil-shale mining, but in many of the country's underground mines in which room-and-pillar methods of mining are employed. This report presents the Bureau's experience in testing the following equipment in the Experimental Oil-Shale mine: 1. A four-drill benching jumbo for drilling 23-foot vertical blast holes 2. A jet borehole blower for efficient cleaning of deep, vertical blast holes. 3. An explosives truck equipped with two compartments to provide safe conveyance for dynamite and detonators. 4. A mobile, electric substation to provide switching equipment, low-voltage and overload protection, and transformer facilities to remote locations in the mine. 5. A chemical conditioner for scrubbing the exhaust gases from Diesel-powered equipment used in underground operations. 6. Other units of equipment which have been tested at the Experimental mine.

Jan 1, 1951

By Robert W. Ageton

The Bureau of Mines investigated the in situ vertical component of the rock stress in the rib of the haulage drift on the 6100-level of the Star mine, Burke, Idaho, using the flatjack and borehole deformation methods. The estimate of the vertical component of stress about 2 feet into the rib at a station along the haulage drift on the 6100-level of the Star mine by the flatjack method is approximately 5,875 psi, whereas the borehole deformation procedure at this station yielded a value of 5,500 psi for the same depth into the rib. The test zone is approximately 5,625 feet below the surface.No attempt was made to extrapolate stress estimates beyond the depth of the flatjack installation.

Jan 1, 1967

By William Catron

This paper is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and cuts in the various reining districts of the United States. The mining methods described are those used in the mines of the Cananea Consolidated Copper Co., a Mexico corporation whose holding company in the United States is the Greene Cananea Copper Co. The mines are at Cananea, Sonora, Mexico, 25 miles directly south of the international boundary, approximately in 31° nor to latitude and 110 to 130° west longitude. Cananea is connected with the boundary towns of Naco and Nogales, Ariz., by a standard-gage railroad.

Jan 1, 1930

By Ernest A. Curth

Statistics For 1956-66 show that mine transportation accidents accounted for 19 percent of fatalities in bituminous coal mines, second only to roof deficiencies as a cause of death. Productivity per man-shift increased from 10.2 tons in 1956 to 18.4 tons in 1966, but the fatalities per million man- hours of exposure also increased from 0.19 to 0.21 during that same period, indicating that transportation hazards still persist. Consequently, the Bureau of Mines reviewed the transportation fatalities that occurred in bituminous coal mines during 1956-66. The data were processed by computer to find what constitute hazardous conditions and unsafe actions as well as to correlate occupation and age of victims, transportation type, and mine production. Environmental factors and equipment defects which create hazards, as well as unsafe actions of personnel, were determined for each type of mine transportation: Track haulage, mobile nonrail haulage, conveyors, hoists, automotive operations, and front -end loaders, and for transfer stations (loading points, slope and shaft bottoms, surface transfers) and railroad yards. Man-trip accidents, a group with a catastrophe potential, also were analyzed. The basic design and operational features of each transportation type were outlined and procedures considered safe in the light of accident experience were suggested. Findings show that unsafe actions of personnel and hazards created by environmental deficiencies or equipment malfunctions contribute equally in causing transportation accidents. Accordingly efforts should be directed toward improving working conditions, equipment maintenance, and education and training of employees. The trend is toward using safer modes of transportation, notably conveyors. More attention should be given to track haulage operation, railroad yards, and nondestructive field testing of materials.

Jan 1, 1971

By A. Soderberg

This paper describing the mining practice at the Utah Copper Co., Bingham Canyon, Utah, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Utah Copper Co. operates the low-grade open-out copper mine at Bingham Canyon, Utah, which is 30 miles in a southwesterly direction from Salt Lake City. In addition to the mine the company operates two flotation concentrators, the Magma plant and the Arthur plant, which have a combined capacity at maximum metallurgical efficiency of 60,000 tons daily. The concentrators are at Magna, about 18 miles from the mine. The company operates its own standard-gage railway, known as the Bingham and Garfield Railway, between the mine and the mills (fig. 1). Concentrates are smelted at the Garfield smelter of the American Smelting and Refining Co., situated 4 miles from the mills.

Jan 1, 1930

By Curtis D. Edgerton

Miami Oölite limestone is the only significant construction mineral in southeastern Florida. Its source area coincides with that of rapid urban expansion. Two-thirds of the existing resource is already unavailable because of development. Land-use conflicts place future availability of limestone in jeopardy. However, a sufficient limestone resource to meet demand for many years is present if its extraction is not restricted. Adverse environmental effects of quarrying Miami Oölite are not severe; land values often increase following quarrying. Future availability depends upon--(l) achieving uniformity of Federal, State, county, and municipality statutory requirements governing quarry operations; (2) setting aside specific land areas for future quarrying; and (3) cooperative planning to provide for land utilization upon completion of quarrying.

Jan 1, 1974

By Alan D. Hartman

Instabilities in electric steelmaking furnace arcs cause electrical and acoustical noise, reduce operating efficiency, increase refractory erosion, and increase electrode usage. The U.S. Bureau of Mines is investigating methods to stabilize these arcs. To perform experiments to test new hypotheses, Bureau researchers designed and instrumented an advanced, experimental single-phase furnace. This report describes this furnace, which was equipped with high-speed data acquisition capabilities for electrical, temperature, pressure, and flow-rate measurements; automated atmosphere control; ballistic calorimetry; and view ports for high-speed cinematography. Precise environmental control and accurate data acquisition allow the statistical design of experiments and assignment of rigorous confidence limits when potential furnace or procedural modifications are tested.

Jan 1, 2010

By Ronald T. Mayerle

In 1989, the U.S. Bureau of Mines conducted a mineral investigation of the Mallard study area near Elk City, Idaho. The study area comprises most of the original Mallard RARE II area (1-847) plus some additional lands. The investigation is part of an ongoing, multi-year study of north-central Idaho that is being conducted in cooperation with the Idaho Geological Survey and the U.S. Geological Survey (USGS). The only identified resources are rock suitable for road metal. Five lode prospects and a pyrite-bearing rock quarry, which is operated by the Forest Service for aggregate, were examined for metals. One of the prospects warrants additional exploration for silver in quartz veins, but the chance of finding an economically minable deposit is limited. Several rock and stream sediment samples were anomalous in various metals. Two of the more promising localities for gold and/or other metals are adjacent to a unit of the Frank Church-River of No Return Wilderness that the USGS classified as having a moderate potential for gold deposits related to fossil hot springs.

Jan 1, 1991

By J. J. Shields

The Bureau of Mines observed two different types of longwall mining; the advancing longwall method and the retreating longwall method at seven bituminous coal mines located in five of the coal producing states. In two mines using the advancing face method, the coal faces were abandoned because of roof failures and poor production. In the other five mines using the retreating method, roof control was good as was production. The success of longwall mining depends on good roof control and good production. The use of self-advancing hydraulic roof supports, such as Westfalia, Dowty, and Wanheim props along with Westfalia coal planers and the Anderton and Eickhoff shearer-loaders have been a factor in recent successes.

Jan 1, 1967

By R. T. Artz, Simpson. O. V.

"INTRODUCTION The provision of escapeways from coal mines is a moral and, in most States, a legal obligation of mine owners and operators. The obligation is not always fulfilled because of the hope that no occasion will ever arise requiring the use of such facilities, and, as time passes without the need for using them, a false sense of security is born in the belief that ""it can't happen here.""The disastrous fire in a mine in Ohio on July 5, 1944, again focused attention on the importance of escapeways in averting disasters and made it clear that one or more dependable exits must be provided from a mine and parts thereof where men might be trapped by being cut off from the regular travel route. This matter of always-having available travelable exits has been advocated for many years by the United States Bureau of Mines."

Aug 1, 1948

By John A. Ruppert

1. It has been proposed that the addition of enough limestone to an open -hearth s lag to give a CaO-3P2O5 ratio of approximately 2-followed by SiO2 firing in an oxidizing atmosphere under the proper conditions of time and temperature will result in a clinker having a magnetic phase containing a preponderance of Mn, Fe, Al, and Mg as oxides and a nonmagnetic phase consisting for the most part of a phosphorus-containing dicalcium silicate. It has been postulated further that the metal oxide phase can be recovered by fine grinding and magnetic separation. These broad principles have been substantiated by numerous clinkering operations made in an electrically fired studio-type kiln, a batch rotary kiln, and a continuous rotary kiln and by magnetic separations made in a Davis -tube separator and a laboratory-size Jeffrey-Steffensen three -roll continuous separator. 2. Quenching the clinker after firing seems to improve its grindability. Microscopic examination of the ground clinker indicates .that the oxide phase grinds down at a somewhat faster rate than the silicate phase. 3. Very fine grinding is necessary to approach liberation, of the oxide phase from the silicate phase. Grinding to ininus-325-mesh, followed by magnetic separation, gave only a rougher concentrate, which had to be reground before final separation. 4. Although the manganese content of the final concentrate was higher, there was some evidence that manganese recovery was lower from a clinker made from a flush s lag than one made from a mixture of tap and flush slags. A possible explanation is that a clinker made from a mixture of slags has a higher iron content and hence is more magnetic and more easily separated.

Jan 1, 1952

By H. D. Hess

This report presents the results of laboratory mineral evaluations conducted by the federal Bureau of Mines under the joint sponsorship of the U.S. Atomic Energy Commission (AEC) and the Bureau a! Ships, U. S. Department of the Navy. The major purpose of this investigation was to examine and evaluate zirconium minerals representing sizeable deposits in an effort to locate com¬mercial sources of high-hafnium ores. Although determination of the hafnium content was the principal objective, each of the zirconium minerals also was analyzed for combined zirconium-hafnium oxide, silica, uranium, thorium, yttrium, and cerium. The general laboratory procedure involved microscopic examination of the test samples, concentration of the hafnium-bearing zirconium mineral by standard laboratory techniques, and analysis of the derived concentrate by quantitative microscopic, chemical, and X-ray spectrographic methods. Of the several hundred samples tested under this program, 147 are discussed in this report, including 94 from domestic occurrences and 53 from widespread foreign sources.

Jan 1, 1962

By C. W. Schultz

The vapor pressure of manganese in equilibrium with a series of liquid iron-manganese alloys was determined by the carrier gas method over a broad range of alloy composition. From these data the activities of manganese in the iron-manganese system were calculated. The system appears to be ideal.

Jan 1, 1966

By Lawrence W. Sott

This Bureau of Mines report presents several factors that currently enter into the design, manufacture, and testing of windows and lenses used in explosion-proof enclosures. Emphasis is also given to the sealing concepts for lenses. Criteria for adhesives and sealants are suggested based on the survivability of an explosion-proof enclosure as a structure, rather than upon the minimum material properties of its constituents. Procedures for surface preparation of adherends are also discussed.

Jan 1, 1982

By E. Divers

This Bureau of Mines report presents results of an underground evaluation to determine the respirable dust and gas control effectiveness of a combined (push-pull) face ventilation system for coal mines. The system utilizes both blowing and exhaust curtain, continuous miners equipped with radio remote control, and flight conveyors. Bureau of Mines tests showed a 97% reduction in respirable dust concentrations from the usual cab position on the continuous miner to the remote control operator's position. This allowed the remote control operator to be well within, and the usual cab position to exceed, Federal respirable dust standards. Tests utilizing a safe tracer gas, sulfur hexafluoride (SF6), to determine the face ventilation effectiveness of the combined blowing and exhaust system showed that the system also has excellent methane dispersion capability. Where wide entries permit, this combined face ventilation system and use of remote control can be a very effective method for dust and gas control.

Jan 1, 1982

By P. R. Miles, J. K. H. Ma, J. Y. C. Ma, L. Bowman

"The bisbenzylisoquinoline alkaloids are compounds which can be isolated from plants and which exhibit a broad range of pharmacological activities. Perhaps the best known alkaloid of this group is tetrandrine (TT), a compound isolated from the root of a traditional Chinese medicinal herb, Stephania tetrandra. It has been tested for its effects on the cardiovascular system, tumors, and the lungs. For example, tetrandrine has been shown to act as a calcium entry blocker in cardiac sarcolemmal vesicles (King et a/., 1988) and has been used in China as a treatment for angina and hypertension. Its possible effects as a tumor-inhibitory substance have also been investigated (Kupchan and Atland, 1973). In addition, there are several lines of evidence to suggest that it is a possible therapeutic agent for the treatment of silicosis. Yu et a/. (1983) have shown that TT inhibits the development of experimental silicosis in rats when it is administered orally after intratracheal instillation of quartz. Other studies have shown that the alkaloid inhibits the synthesis of collagen by fibroblasts and the formation of silicotic nodules in rats exposed to silica (Huang et al., 1981; Liu et al., 1983). In fact, tetrandrine has been used clinically in China as an antifibrotic agent and has been shown to improve both the appearance of chest radiographs and the measurements of diffusing capacity in patients with silicosis (Li et al., 1981).Since tetrandrine may have a potential use as a therapeutic agent for fibrotic lung diseases, its effects on various pulmonary cells and tissues should be studied. Alveolar type II cells are located in the alveolar regions of the lungs and are important because they are responsible for the synthesis and secretion of pulmonary surfactant (Dobbs et al., 1982; King, 1984), regeneration of the alveolar epithelium after lung injury (Kauffman et al., 1974), and metabolism of foreign compounds (Bend et al., 1985). Furthermore, in silicosis, for which TT has been suggested as a treatment, there are increased amounts of pulmonary surfactant produced (Dethloff et al., 1986a,b) as a result of increased rates of surfactant synthesis by type II cells (Dethloff et a/., 1989; Miller et al., 1988). Because type II cells play a critical role in maintaining normal lung function and because type II cells are affected in silicosis, for which 'TT has been used as a treatment, we studied the effects of tetrandrine on energy metabolism in these cells in vitro. Energy metabolism was chosen because it is a basic cellular function which is neces-sary for other cellular processes to occur. Since type II cells depend on mitochondrial metabolism for energy production (Fisher et al., 1980), we examined the effects of tetrandrine on cellular and mitochondrial ATP production and oxygen consumption. Additional experiments were performed in an effort to determine if intracellular calcium levels may be involved in the TT-induced effects. A preliminary report of those results has appeared previously (Ma et al., 1991)."

Nov 1, 1995

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

"DIGREGORIO, K. A., E. V. CILENTO, AND R. C. LANTZ. A kinetic model of superoxide production from single pulmonary alueolar macrophages. Am. J. Physiol. 256 (Cell Physiol. 25): C405-C412, 1989.-A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared with experimental results obtained from single rat PAM. The 02 was quantified by measuring the reduction of nitro blue tetrazolium (NBT) to a diformazan precipitate (NBTH,) from video-recorded images of individual cells. The kinetic model considered three reactions: 1 ) the production of extracellular 02 from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, 2) the subsequent dismutation of 02 to form H,O,, and 3) the reaction of 02 and NBT to form diformazan. NBT specificity for 02 was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) that catalyzes the dismutation of 02 to H,O,. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations because NBT is a relatively small molecule (818 mo! wt) compared with SOD (34,000 mol wt). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/ or electrostatic effects, since SOD is also negatively charged, whereas NBT is positively charged.PULMONARY ALVEOLAR MACROPHAGES (PAM) protect the lungs by phagocytizing foreign debris and bacteria. This process is accompanied by the production of superoxide anion (02) at the surface of the plasma membrane (3, 31). Superoxide readily dismutates to form H20 2 and subsequently, other oxygen metabolites which have been shown to be both antibacterial and cytotoxic (21, 25, 35).Superoxide is produced from the reduction of extracellular O, at the surface of the cell membrane by NADPH oxidase by the following reaction (3, 4)"

Jan 1, 1989

By Florence L. Feicht, Carlton E. Brown

"INTRODUCTION This report contains information on the approximate size of the smallest dust Particles revealed by or the limit of visibility of various microscopic systems. The information was obtained mainly for use in interpreting and evaluating results of number-contentration and particle-size, determinations on, samples of unhygienic particulate matter collected from industrial atmospheres and in developing better methods for determinations nations.Some speculation and even controversy have been published on the limit of visibility of the widely used microscopic system (16-mm., 0.25-or 0.3-N.A. objective, and axial light-field illumination) used in counting the dust in the liquid medium from impinger, 4/ 5/ filter-paper, 6/ and other samples, but little or no quantitative data have been published on the limits of visibility of this or other microscopic' system.ACKNOWLEDGMENTSThe interest, encouragement, and assistance received from H. H. Schrenk, chief of the Health Division are gratefully acknowledged, as is all other assistance received in this study."

Aug 1, 1945

By L. D. Schmidt, H. G. Graham

Several processes for the production of ultra-clean coal for electrode carbon were developed in Germany prior to and during World War II . These processes have been investigated since the end of the war by the British and U. S. Government missions . As the reports of the investigations are not readily available to the public , it is the purpose of this paper to present the information which has been obtained regarding the methods by which ultraclean coal was produced . Almost all the ultra-clean coal was used in the manufacture of electrodes for the production of aluminum and magnesium . Standard raw materials for making these electrodes are pitch coke and petroleum coke , which are nearly ashless . The inclusion of ash in the electrode carbon results in lowered efficiency and impure metal from the reduction process . Petroleum coke and pitch coke were in very short supply in Germany during the war , so that it was necessary to augment the supply with carbon produced from coal . In the emergency , methods were developed to clean coal which had never before been economically feasible . However , a demand for nearly ash-free coal might develop in the United States if a shortage of petroleum coke were to occur at the same time as a strong demand for light metals . Other uses of ultraclean coal are in direct hydrogenation of coal , in production of activated carbon, and for special fuels . Specifications for electrode carbon are rather severe owing to the necessity for producing pure metal . Maximum amounts of impurities allowable in American practice are as follows : Total ash , 1.0 percent ( in finished coke , 0.7 percent ) Silica , 0.08 percent Ca or Na, or their sum , 0.12 percent Sulfur , 2.0 percent Ba , Ni , Cr , Mn , Co , and V are objectionable in very small amounts . The most important process for ultra cleaning of coal in Germany was froth flotation . Froth flotation had been used widely there to process washery -water sludges and to recover coking coal from high - ash fines . Its use was indicated , therefore , when the demand for ultra low-ash coal arose . In two plants the coal cleaned by froth flotation was treated with acid or caustic to lower further the ash content . Another process used on an industrial scale was that of dissolving the coal substance in the middle oil from direct hydrogenation of coal under controlled pressure and temperature . The resulting paste was heated, filtered , and the oil distilled off . The residue was a low-ash organic material that could be carbonized for electrode carbon or could be hydrogenated directly . Several other processes had been developed to the laboratory or pilot - plant stage but had never been used on a commercial scale . These processes included cleaning by centrifugal action , cleaning by electrostatic action , and cleaning by forming a paste with oil in water . The coal-preparation plants at the Carl Alexander mine , Augusta Viktoria mine , and Kőenigin Elisabeth mine are described in Bureau of Mines Information Circular 7389 : " Coal Preparation Practice in Western Germany" , by Thomas . Fraser and M. G. Driessen . Most of the special equipment used at these plants is described in the above publication .

Oct 1, 1948

By Cleo G. Rall

The method for determining the effective porosity of oil- and gas-bearing sands described in this report is a development of earlier methods (28)3/ devised by the Bureau of Mines. The apparatus bas been improved and made more convenient to use, but the procedure is essentially the same as that which has been in use for maw years. A tabulation at the end of the report gives the results of more than 4,800 porosity determinations for oil sands4/ in the fields of 13 States, A selected bibliography of references to articles containing descriptions and evaluations of various methods of' determining porosity is included in this report. The method was devised and developed at the Petroleum Experiment Station at Bartlesville, Okla., as part of the Bureau's research on fluid-energy relationships and on methods of improving the recovery of crude oil from underground reservoirs.

Jan 1, 1954