Search Documents

By Constantine C. Popoff

The Hermada antimony deposit is in the Sewtooth Range in southwestern Idaho, about 77 miles by road northeast of Boise. Stibnite mineralization occurs over an area one mile wide from west to east and two miles long. It is locally referred to as the Swanholm district. In 1947 high- grade stibnite ore was discovered on the East Fork of Swanholm Creek. Since then, ore in commercial quantity has been produced by the Hermada Mining Co. The total output for 1947-50 was about 5,000 tons of ore, containing 640 short tons of antimony metal.

Jan 1, 1953

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United states was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United states Department of the Interiors This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941.£1 No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed

Jan 1, 1949

By R. D. Leitch, C. A. Taylor

Trinitrotoluene is made by the direct nitration of toluene by a mixture of nitric and sulphuric acids . The exact procedure varies , but the product , where Grade I of TNT is desired , is similar , and consists largely of material that has a melting and setting point of 80.6 °c . The purification consists of draining off the liquid portions , including the acid and liquid nitro compounds . The mass is crushed and washed until the TNT is acid - free . It may still have a low-melting point due to the presence of material of lower nitration. Other isomers also have the same effect . The crystal mass may be washed with a solution of sodium sulphite , thiosulphate , sulphuric acid , or with an organic solvent such as alcohol , benzene , or carbon tetrachloride , Where a very pure product is desired , the TNT is separated by fractional crystallization from solution in organic solvents . The TNT is If it forms In some cases the material is melted during purification . agitated as it cools to prevent solidification in a solid mass . in a solid mass , this is broken up and screened . There has been some question as to the effect of the different methods of purification on the strength and sensitiveness of TNT , although all methods left a product that would give satisfactory tests .

Sep 1, 1923

By F. P. Haver

Because of increasing concern with air pollution, the Bureau of Mines has developed a hydrometallurgical procedure to obtain elemental sulfur from chalcopyrite (CuFeS2) by means of the following reaction: CuFeS2 + 3FeCl3 ? CuCl + 4FeCl2 + 2S. Under optimum conditions, 99.6 percent of the copper and 71.6 percent of the iron were extracted in 2 hours from a typical mill concentrate containing 75 percent CuFeS2 and 15 percent pyrite (FeS2). At the same time, 68.2 percent of the sulfur in the concentrate was oxidized to the elemental form. The leach was highly selective; gangue minerals, including pyrite, were not attacked, thus accounting for the relatively low recoveries of iron and sulfur. To obtain these results, the concentrate was ground to 98.9 percent minus 325 mesh, and 300 grams was treated with 1 liter of boiling ferric chloride (FeCl3) solution. The FeC13/CuFeS2 ratio was 2.7. Cement copper containing 99.9 percent copper was recovered from the leach solution by cementation on sponge iron. Excess iron, dissolved during leaching and cementation, was removed from the stripped solution by crystallization. Ferrous chloride (FeCl2?4H2O), obtained as a byproduct, was converted to high-purity ferric oxide (Fe203) and HCI by an oxidizing roast. The hydrochloric acid was then electrolyzed to obtain chlorine, which was used to regenerate the leach solution. The leach residue, which contained ~50 weight-percent elemental sulfur, was treated with an organic solvent to recover the sulfur and cyanided to reclaim gold and silver.

Jan 1, 1971

By A. C. Johnson, es Hol, E. O. Binyon

"INTRODUCTION AND SUMMARYThe tungsten properties of Lincoln Mines, Inc., and North Tem Flute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co.Claims leased by the Lincoln Mines, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57 E.: and sec. 1, T. 4 S., R 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc. and general offices are in the Wesley Temple Building, Minneapolis, Minn.In June 1945, the Atolia Mining Co. leased the property and purchased the mill and mining equipment from Lincoln Mines, Inc. P. R. Bradley is president of the Atolia Mining Co., whose offices are in the Crocker Building, San Francisco, Calif. This company surrendered the lease on the property on September 30, 1948. The property owners are continuing operations and are now engaged in building a 20-ton mill.The claims of the North Tern Flute Mining & Development Cc. are in sec. 1, T. 4 S., R. 56 E., M. D. B. & M. Merle F. Schofield is president of the company and maintains an office at Hike, Nev. These claims were leased by H. P. Laslett, of the Utah Nevada Mining Co., in 1945 and by the Atolia Mining Co. in 1946. The owners are now doing some exploratory work."

Jan 1, 1950

By Benjamin W. Haynes

Analytical procedures are described for the quantitative determination of 16 elements (As, Ba, Be, Cd, Co, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn) and 7 ionic species (NH4, C032-, CI-, F-, NO3-, P043-, SO42-), identification of major and minor mineral components, and measurement of physical properties associated with manganese nodules and nodule processing reject waste materials. Compound identification methods discussed include X-ray diffraction, infrared spectroscopy, scanning and transmission electron microscopy, selective area electron diffraction, and optical and reflected light microscopy. Methods for elemental analysis include atomic absorption spectrophotometry, inductively coupled plasma emission spectroscopy, neutron activation analysis, fluorescent X-ray spectrography, and ion chromatography. Thermal gravimetric analysis, ultraviolet-visible spectrophotometry, ion specific electrodes, and standard wet chemical procedures are briefly discussed. Physical properties determined in manganese nodule materials include grain size distribution, specific gravity, triaxial shear, permeability, maximum density, Atterberg limits, and slurry density. The results of a round-robin analysis of an ammonia process waste material and manganese nodule standards demonstrate the applicability of the discussed methods. Tests discussed for the evaluation of the waste materials for disposal options include the Environmental Protection Agency (EPA) EP toxicity test, the ASTM shake extraction test, and the U.S. Army Corps of Engineers EPA seawater elutriant test.

Jan 1, 1983

By Martin J. Gavin

In an earlier paper (Karrick, Lewis, C. A convenient and reliable retort for assaying oil-shales for oil yield: Bureau of Mines, Reports of Investigations, Loral No. 2229, March, 1921. Reprinted in Eng. and Min. Jour, April 30, 1921, also in Mining & Met., May, 1921) which describes the apparatus and method used in the laboratories of the Bureau of times for assaying oil-shales, no mention is made of the quality of oil obtained when the apparatus is operated under conditions determined to be most suitable for producing highest yields of oils. So many inquiries regarding the nature of the oil have been received, that it seems advisable to present a short report on the subject. Experimental work indicates that it is possible to vary the quantity and quality of the oil obtainable with the assay retort from a given shale by varying the conditions of retorting. As an example, some figures that are averages for several closely agreeing tests are shown below.

Jan 1, 1921

By Wesley T. Holmes

In this final stage of a three-part investigation of the smelting of titania-bearing iron materials, the Bureau of Mines conducted semicontinuous smelting tests in a laboratory electric arc furnace on four concentrates and one are. The objective was to substantiate the significance of liquidus temperature measurements in predicting satisfactory slag compositions in electric furnace smelting of titaniferous magnetites to produce pig iron. Previously obtained liquidus temperature data were used in determining flux requirements. Self-fluxing pellets of either ore or concentrate plus fluxes and reductants were made to produce pig iron and slags containing 0.2 to 0.6 percent titanium. Individual constituents of the slags generally agreed within 5 percent with the value of the corresponding constituent of target composition. Liquidus temperature of furnace slags generally agreed within 50° C of the value obtained from corresponding nominal synthetic slag. The results of the three phases of the investigation may serve as guide-lines for determining flux requirements in smelting a wide variety of titaniferous magnetites and other titania and iron-bearing materials.

Jan 1, 1969

By R. M. Gooding

This paper presents a short history of the production of mineral-energy fuels and energy from waterpower in the United States, with brief discussions of the utilization of each of the fuels and hydropower, and a look at fuels competition and interchangeability. Basic data, in figures and tables, are brought together in this publication for the production of coal in the United States from 1800 to 1960, for crude petroleum, natural gas liquids, and natural gas from 1859 to 1960, and for hydropower since 1900. Production for each segment of the fuels complex in the principal producing States from 1946 to 1960 is shown. Data are not included for consumption as such or for imports and exports.

Jan 1, 1963

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated an ammoniacal sulfate leach process for recovering nickel and cobalt from low-grade domestic laterites. Solvent extraction of cobalt, one of the process steps, requires the reduction of hexammine complexes of C03+ to C02+ in an ammo-niacal leach solution. Previously, reduction was accomplished using cobalt metal shot in a column. This report presents experimental results and an economic evaluation comparing two alternate techniques with the shot column: (1) an electrolytic reduction cell with an extended surface area cathode and (2) direct electrowinning from purified leach solution using a cell with a fluid bed cathode. The second alternative eliminates the conventional solvent extraction-electrowinning steps. The costs of the three methods, based on the requirements of a pro-posed commercial-sized plant, including all unit operations, were deter-mined by the Bureau's process evaluation group. The operating costs for the shot column, $1.19/kg Co, and for electrolytic reduction, $1.20/kg, are essentially the same, but the cost of direct electrowinning, $3.77/ kg Co, would eliminate this method as a practical alternative. The cap-ital cost of approximately $14.4 million for reduction in a shot column is much higher than the approximately $4.4 million for electroreduction.

Jan 1, 1985

By J. H. Johnson

The report references reports and publications from 1975 to the present related to diesel underground mine air quality research undertaken by Michigan Technological University. Research results obtained on this contract are summarized in 5 different sections as follows: Section 1 - Development of a Systematic Approach to Monitoring, Data Analysis, and Interpretation for Diesel Mine Air Quality Control, Section 2 - Experimental Evaluation of LHD On-Board Air Quality Control Systems, Section 3 - Development of a Portable Self-Contained LHD Tailpipe Emissions Measurement Apparatus for NO , N0, CO, CO , and Particulate Matter, Section 4 Quantitative Analysis of Diesel and Coal particulate Matter by Laser Raman Spectro¬scopy and Section 5 - Development and Application to Detector Tubes of a Laboratory Method to Assess Accuracy of Occupational Diesel Pollutant Concentration Measurements.

Jan 1, 1985

By John H. Hild

This is a report on work done and results obtained in a minerals exploration program conducted by the Bureau of Mines on the lead-zinc deposits in the Ross Basin-Lake Como district, San Juan County, Colo., in 1948, 1949, and 1950. Four large veins--the Seven Thirty, Red Rogers, Cashier-Shorts top-Canandaigua, and Queen Anne--and several narrow spur veins were explored at relatively shallow depths with core-drill holes. Thirty-nine holes, totaling 10,491.5 feet, were drilled, and the core samples were assayed at the Bureau of Mines station at Salt Lake City, Utah.

Jan 1, 1959

By A. R. Rule

This report describes preliminary studies by the Bureau of Mines to develop a procedure for extracting the fluorine from low-grade fluorspar ores in which the CaF2 particles are finely locked in the calcite matrix. A combination of flotation beneficiation and pyrohydrolysis is applied to recover and to liberate the fluorine. Flotation of a finely locked high-calcite fluorspar ore containing only 11.7 pct CaF2 recovered over 92 pct of the fluorspar at a grade of 51 to 52 pct CaF2. Pyrohydrolysis of the flotation concentrate liberated nearly 90 pct of the fluorine as aqueous HF. By this procedure over 80 pct of the fluorine contained in the original ore was extracted.

Jan 1, 1974

By E. G. Noble

The effects of HBr concentration and temperature on the solubility and hydration state of AlBr3,' CoBr2, PbBr2, MnBr2, KBr, and NaBr were investigated by the Bureau of Mines. Saturated aqueous solutions of the AI, Pb, K, and Na bromides were sparged with HBr gas at 20°, 40°, and 60° C, and saturated solutions of Co and Mn bromides were sparged at 20° C. Increased HBr concentration caused decreased salt solubility because of the common ion effect for all the investigated bromides except PbBr2. Aqueous solubilities at 20° C were, in percent, 51.7 for AlBr3, 53.2 for CoBr2, 1.1 for PbBr2, 59.6 for MnBr2' 39.5 for KBr, and 47.4 for NaBr. At 60° C, the solubilities were, in percent, 53.3 for AlBr3, 2.2 for PbBr2' 46.0 for KBr, and 53.8 for NaBr. Solubilities in solutions sparged to HBr saturation at 20° C were, in percent, 0.5 for AlBr3, 42.0 for CoBr2, 32.2 for PbBr2, 21.0 for MnBr2, 0.6 for KBr, and 0.3 for NaBr. At 60° C, the solubilities at HBr saturation were, in percent, 1.8 for AlBr3, 41.4 for PbBr2, 1.3 for KBr, and 0.4 for NaBr. CoBr2 precipitated out to a minimum solubility of 27.2 pct at 28.7-pct-HBr concentration. Further increases in HBr concentration increased CoBr2 solubility because of the formation of bromide complexes. PbBr2 in-creased in solubility as HBr concentration increased.

Jan 1, 1988

By Amanda S. Azman

It is known that exposure to high sound pressure levels can lead to permanent hearing loss; however, many workers, in mining as well as other occupational sectors, frequently receive hazardous noise exposures. The National Institute for Occupational Safety and Health (NIOSH) recommends using a criterion level of 85 dB(A) for implementation of hearing loss prevention programs1. But, despite engineering and administrative controls, workers continue to exceed their recommended daily noise dose. Hearing protection devices are worn as a final defense against noise overexposure, but many workers have difficulty communicating or detecting warning signals while wearing them. New electronic technology has been integrated into conventional hearing protectors to allow for some degree of sound restoration. Research is currently being carried out within NIOSH, Pittsburgh Research Laboratory (PRL) to evaluate the performance of sound restoration hearing protectors. Due to certain features of the devices, such as their non-linear performance and possible manipulation of electronic settings, there are obstacles to testing them using the existing standard hearing protector test methodology (ANSI S12.42-1995 and ISO 4869-3:1997). These and other issues related to testing these devices are outlined within this paper, and possible solutions are discussed. Measures of attenuation properties have been done on a set of the devices and preliminary findings indicate that new test methods, or at least modifications of existing methods, must be developed to accurately determine device performance. Furthermore, it is necessary to know not only the attenuation properties of such devices, but also the degree to which speech intelligibility or recognition of warning signals is preserved, as compared with conventional hearing protectors. As additional data is collected a more accurate and reliable test methodology will be developed, and a more comprehensive picture regarding device performance will be determined and disseminated.

Jan 1, 2008

By J. H. Bilbrey

A recording thermobalance ,vas used to determine the rates of oxidation of mol-ten tin over the temperature range 550°-900° C. Oxidation rates were found to vary widely for a given temperature, as previously reported by other investigators. 1 X-ray diffraction data indicated that the probable cause of these variations was the development of preferred orientations in the crystals forming the oxide film. No reasons for the differences in degree of preferred orientation were discovered. For relating the weight of the oxide formed (w) to the time of oxidation (t) an equation of the form wn = kt was found to best represent the experimental data. INTRODUCTION In the course of conducting investigations on the feasibility of using selective oxidation techniques for the purification of various metals in the molten state it was soon discovered that data on the oxidation of molten metals and alloys were very scarce. In contrast to the many hundreds of publications on the oxidation of metals in the solid state there are relatively few articles on the rates of molten-metal oxidation. In view of this scarcity of data, it was decided to institute a series of investigations into the oxidation processes of molten nonferrous metals and alloys with the expectation that the information derived could be put to practical use in developing and improving refining processes based on selective oxidation. This report is the first of a series in which oxidation data for molten nonferrous metals and alloys are presented.

Jan 1, 1955

By R. L. Grant

An investigation was undertaken by the Bureau of Mines to determine the relationship between freespace and ignition probability for borehole shots. A series of experiments was concluded which covered six freespace conditions for a pemissible explosive in a 3/4-inch borehole and encompassed some 700 shots. The results were analyzed statistically. From the analysis of variance, it was concluded that the freespace means were different and that this conclusion is not impaired by possible differences in the explosives used. Within the limitation of this experiment, a definite relationship was found between the freespace and the ignition probability. Specifically, the incendivity increases with increased freespace up to a maximum; beyond this maximum there is some indication of decreasing incendivity. Further investigations are in progress to establish whether the effects of freespace on ignition probability reported here are applicable to the large test gallery, INTRODUCTION A borehole loaded with an explosive charge is a common feature of the routine gallery tests for determining the permissibility of coal-mine explosives, of Experimental Coal-Mine shots, and of the small steel cannon shots used in connection with certain research programs on the ignition of firedamp (6, 10).6/ The question of the interrelationship of freespace, weight of charge, and ignition probability of the methane-air atmosphere has been raised

Jan 1, 1959

By Spencer P. Howell, Munroem Charles E.

"Introduction;As in the case of TNT previously presented*, this report presents the results of an investigation to discover the safest and best way of utilizing picric acid for industrial blasting purposes. It describes the physical and chemical properties of this explosive, gives precautions to be observed in handling, packing, preparation of cartridges, and holes, presents the results of field tests in blasting stumps and bowlders, and compares the results with those obtained from dynamite.The investigations reported herein were undertaken and this paper has been prepared, solely to aid in the salvage of the surplus picric acid accumulated for war uses and released by the declaration of the armistice. No funds were available nor have any been appropriated with which to defray the expense of converting this picric acid into any other form or to prepare any explosive mixture from it. The sole problem was to find appropriate uses for this military picric acid in existing needs and to show that it can be efficiently used in carrying out essential civil projects.It is not intended by this publication to promote the use of picric acid as an industrial explosive further than is necessary for the proper utilization of this surplus. On the contrary, the authors believe that picric acid by itself is unlikely to come into general use as an industrial explosive, chiefly because of its cost but also as shown by the clouds of smoke it emits on explosion and the nature of the reactions it undergoes because we do not obtain from it its highest efficiency. As demonstrated in its previous use in Joveite, better results and higher efficiencies may be obtained by mixing picric acid in proper proportions with sodium nitrate or ammonium nitrate, to more completely oxidize the picric acid, and another nitrosubstitution compound, such as nitronaphthalenes, with which do desensitize and waterproof the composition formed. By such admixture not only may the energy resident in the picric acid, be more fully utilized but the cost of the resulting blasting explosive should be much less than that of picric acid."

Apr 1, 1921

By P. C. Good

High-purity chromium was prepared in massive form by the electrolysis of chromium trioxide solution at high temperatures. The metal thus obtained, containing 50 to 150 p.p.m. of oxygen, 20 p.p.m. of nitrogen, and traces of metallic impurities, could be hot-worked to rod and sheet and drawn to wire ductile at room temperatures. Optimum concentrations and operating conditions were established for the deposition of chromium from chromic acid baths containing sulfate, fluoride, and silicofluoride ions. Current efficiencies of 13 percent were attained with baths containing sulfate ion, and efficiencies of 40 to 44 percent with baths containing fluoride and silicofluoride ions. Cation exchange resins were used for removing metallic impurities from chromic acid solutions containing sulfate ion; solutions containing fluoride and silicofluoride ions were purified by recrystallization.

Jan 1, 1960