Search Documents

By W. T. Benson

The nickel-bearing laterite deposits in the Pine Flat and Diamond Flat areas, Del Norte County, Calif., were investigated by the Bureau of Mines to determine the extent and nickel content of the two deposits and the amenability of the ores to metallurgical treatment. The work was based on drill-hole sampling and metallurgical tests in which attrition scrubbing and sizing, reduction roasting, and magnetic separation were used. Results of the sampling indicated that the deposits are comparatively small and are marginal or submarginal in grade. Metallurgical tests showed that no separation of cobalt from nickel and iron was made by sizing; however, a large portion of the chromium was separated. Reduction roasting and magnetic separation did result in upgrading the iron, nickel, and cobalt, and the simultaneous rejection of chromium.

Jan 1, 1963

By Martin H. Stanczyk

The direct dissolution of a typical zinc sulfide flotation concentrate by elevated temperature and pressure leaching was investigated. The concentrate assayed about 55 percent Zn, 32 percent S, 6 percent Fe, and 1 percent Pb and contained minor quantities of copper and precious metals. The influence of various factors on the dissolution of the zinc in acidic and ammoniacal pulps when using oxygen as the oxidant was determined. The tests revealed that the sphalerite was difficult to oxidize. Complete dissolution of the mineral required vigorous and intimate nixing of the gaseous, liquid, and sold phases. The addition of pyrite or sulfuric acid to water slurries of the concentrate was required to obtain a high zinc extraction when leaching under acidic conditions. The quantity of pyrite and acid used was about 0.125 and 0.25 pound, respectively, per pound of zinc sulfide contained in the leach charge. In tests with acid, about 96 percent of the zinc was extracted from the concentrate in 1 hour at 200° C. when the oxygen partial pressure was 75 pounds per square inch gage or higher. Leaching with a continuous flow of air as the oxidant gave results that were almost as good as those obtained when oxygen was used, In tests with air fed through the autoclave at 320 liters per hour, 95 percent of the zinc was dissolved in 1 hour, Acid leach solutions assaying approximately 58 grams Zn per liter and containing Fe, Ni, Cr, and Cu impurities were produced in the better tests. The leached residue consisted essentially of red iron oxide together with substantially all of the lead and precious metals.

Jan 1, 1961

By Arthur B. Campbell

This Bureau of Mines report describes a method that utilizes a computer program to evaluate integral Gaussian profiles of atomic concentration versus depth in a solid. The specific use illustrated involves profiling ion- implanted metals using proton-induced X-ray emission (PIXE) analysis and ion sputtering (IS) for sectioning

Jan 1, 1979

By J. R. Thoenen

During 1928 questionnaires covering the calendar year 1927 were sent to over 1700 quarries: producing stone for purposes other thaw cutting to dimension. These inclined producers of stone for limn burning; cement manufacture, rip rag, and crushed stone. The various rinds of stone represented were limestone, trap rock, sandstone, granite, and marble. Replies received from limestone producers prior to November, 1928, were compiled into tables and published in February, 1925, as a preliminary report (Bureau of Mines Report of Investigation 2911).

Jan 1, 1930

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By B. E. Davis

As part of its program to increase the domestic availability of critical minerals, the Bureau of Mines conducted characterization and beneficiation studies on a St. Johns County, Fla., phosphate ore that was mined by borehole mining. Results revealed that the ore from this test mine was mostly sand-size carbonate-fluorapatite and quartz and contained 24.6 percent P205. Concentration by various flotation techniques produced phosphate concentrates that ranged, in percent, from 30.0 to 31.4 P205, 0.73 to 0.80 MgO, and 2.8 to 7.2 acid insoluble. Recovery of the phosphate from the ore ranged from 89.4 to 96.3 percent.

Jan 1, 1982

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By L. C. IlsLey

In the normal operation of mines, the aggregate effect of many seemingly minor op rations may be very important as respects economy and safety. Anion: these operations is the method employed in coupling and uncoupling mine cars. For economic reasons the equipment in mines has not been protected as well as railroad equipment. It is pertinent that haulage accidents rank second in severity among mine accidents, and that manual coupling of cars has been one of the most frequent causes of such accidents. One study4/ revealed that coupling was responsible for about 20 percent of haulage accidents underground. A review of early conditions on steam railroads, which were responsible for the introduction of safer methods of coupling cars, indicates how conditions in might be improved. THE STORY OF RAILROAD COUPLING As any considerable improvement in mine-car coupling probably will follow lines somewhat similar to those that brought order out of chaos for the railroads, it seems appropriate to review briefly the steps taken to improve railroad coupling from the days of link and pin couplings of various types to the adoption of the standard ?M.C.E? automatic coupler.

Jan 1, 1943

By Frank D. Lamb, D. A. Woodard

"INTRODUCTION The iron-ore deposits near Cranberry, N. C., were worked as early as 1820, and records show that to date at least 1,500,000 tons of ore has been mined.. The early operators depended on selective mining and hand cobbing to yield a product containing 40 to 50 percent iron. Later, a magnetic concentrator was erected by the Cranberry Furnace Co. and was operated periodically until 1930. The magnetic cobbing method employed yielded satisfactory concentrates, but the plant was shut down because costs were too high. 4/Early in 1944, in connection with the sponge-iron program of the Bureau of Mines, North Carolina and Tennessee were surveyed for the purpose of finding a readily available source of high-grade iron ore for use in the experimental production of sponge iron at Salisbury, N. C., and samples from various sources were tested in the laboratory. The Cranberry ore proved to be best with respect to grade of magnetite concentrates produced, and it was decided that a pilot mill should be built on the Cranberry mine property and that the concentrate made there should be shipped to Salisbury for direct-reduction tests in a commercial brick kiln."

Dec 1, 1946

By E. S. Shedd

Misch metal was electrowon from a treated bastnasite concentrate in a REF3-LiF-BaF2 electrolyte at 950° C. The metal was prepared and tapped from a 1,000-ampere cell, and nearly 100-percent utilization of the rare-earth oxide was achieved. Prolonged operation in a smaller cell (40 amperes) indicated that the composition of the misch metal product was reasonably constant, and no significant increase of impurities, with the exception of carbon, was noted.

Jan 1, 1970

By W. M. Dressel

The Federal Bureau of Mines has obtained data by differential thermal analysis of the various minerals that represent the nation's resources in manganese. These data are supported by X-ray diffraction analysis, chemical analysis, mineralography, and optical mineralogy, and provide fundamental information on the response of each mineral to thermal treatment in oxidizing, reducing, and neutral atmospheres. The information can be applied advantage¬ously in the identification of manganese minerals. Its greatest potential value, however, lies in the application of the quantitative data on the reaction temperatures, rates, and products to the more efficient extraction of manganese from U.S. ores. Thermal analysis curves are presented for certain manganese minerals, namely hausmannite, bixbyite, braunite, pyrolusite, lithiophorite, cryptomelane, hollandite, manganite, rhodochrosite, and rhodonite. The original minerals and the products of their thermal decomposition were identified by X-ray diffraction analysis, supplemented by chemical analysis and mineralogical identification.

Jan 1, 1961

By E. G. Valdez

Laboratory research demonstrated that ceramic wall and floor tile can be produced from electric furnace phosphorus slags composed of calcium silicates. Grinding the slag in a pebble mill, followed by magnetic removal of deleterious magnetite, produced a raw material that could be compounded and formed into wall tile by dry pressing, sintering, and glazing. The effects of process variables such as forming pressure and sintering temperature were investigated. Wall tile bodies produced by this method were comparable to commercial tile. The tiles were readily glazed to a smooth shiny finish and met ASTM Specifications C34-62 for structural clay load-bearing tile. The estimated cost of producing wall tile by this method compared favorably with the retail market value for similar wall tile. Addition of borax or other additives to the ground slag followed by dry pressing and firing likewise produced a commercial grade of floor tile.

Jan 1, 1974

By A. U. Miller

Since the organization of the Federal Bureau of Mines, part of the duties of the field men of the Safety Division has been to teach those connected with the minerals industries how to render the proper assistance to an injured worker between the time of the accident and the time when the injured receives medical attention--in other words, "first aid to the injured." For a number of years after the training was introduced, the response of mine officials and workers was very slow. Many times Bureau instructors devoted at least a week to training 5 to 15 or a few more men. However, in recent years since the companies and the Bureau of Mines have had an opportunity to study the results of first aid training, it has been found that in addition to taking care of an injured worker after an accident and thereby greatly reducing the severity rate, the tendency is for the majority of those who take the training to be more careful in their work, or to be more "safety conscious."

Jan 1, 1938

By Robert T. Beckman

The results of a preliminary investigation of compressive strength versus length-diameter (L/D) ratios of potash specimens and the statistical treatment of the data are summarized in this report. The purpose of the study was to evaluate a laboratory method for obtaining estimates of the strength of potash pillars during robbing operations. The specific objectives of this preliminary investigation were to test the method and the reliability (confidence limits) of the data, and to determine the number of additional specimens necessary for given confidence limits. The specimens were taken from three sites at two mines in New Mexico. The statistical analyses included the determination of the confidence limits for the data and the number of additional specimens necessary to obtain confidence limits of ±500 and 100 psi. The testing method was found acceptable, and estimates of the comprehensive strength, within 1500 psi, could be obtained by testing about 110 additional specimens from the three sites. The compressive strength of the specimens tested fits an empirical equation of the type

Dec 1, 1963

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By Shirley F. Colby

A continued rise in construction activity in 1941 forecasts further increases in the demand for building materials of mineral origin, Recent studies by the Bureau of Mines, United States Department of the Interior, reveal that sales of mine and quarry products and their derivatives as a class have followed the long-term trend of construction activity in the past and are benefiting now by the upswing in all types of building. At present most building materials of mineral origin are holding their own in the competitive arena. A few are slipping behind, but others have forged fax ahead. Prominent among those that have surpassed general construction activity since 1925 are sand, gravel, and crushed stone (used in concrete and road metal and railroad ballast) and cement. Both building stone and roofing slate have followed the building curve closely, although in the last few years sales of roofing slate have risen above the curve and sales of building stone have dropped below it. Clay products and building lime, on the other hand, have lagged behind the general procession. Gypsum sales likewise dropped behind, but during the last few years, this industry, thanks to the wider acceptance of its newer products, has staged a marked recovery so that it now stands in about the same relation to total construction activity as it did is 1927-25.

Jan 1, 1941

By Manuel Gomez

A computerized, interpolative mapping technique based on the moving average method was shown to be adequate to estimate the between-drill-hole values of coal-seam variables. The forecasting of the spatial distribution of coal properties along the seam was of three kinds: (1) Estimation of the variable of interest on a regional basis from widely spaced sample points, (2) prediction of coal properties for product control from closely spaced data, and (3) prediction of coal properties for specified benches, or layers of the coal seam, from closely spaced sample points. Estimates obtained with the computerized, interpolative mapping procedure were useful in the delineation of seam thickness, elevation, and overburden and in the estimation of sulfur and ash concentrations during the early phases of exploration. This grid interpolation technique was found adequate to adjust between-drill-hole values for trends resulting from the combined effect of several variables on a measured response. This information, coupled with statistical and geologic data that can be obtained in the exploration phase of mining, enlarges the information base available for coal-mine development planning, energy forecasts, and environmental control associated with fossil fuel power generation.

Jan 1, 1972

By D. Harrington

Ventilation of underground workings consists of establishment of such control of air currents that the underground workers may work in safety, with maximum comfort and efficiency, mad without impairment of health; and that the mine openings may be made subject to such control of air flow as to remove from the workings at ordinary times harmful gases and dusts, and at time of emergency, such as fire or explosion, there may be maintained as much or as little air flow as may be desired covering portions of the mine or the mine in its entirety. Control of air flow is the keystone of any ventilating structure, and this very essential feature is obtainable only by the installation of mechanically operated fans, to ether with other ventilating devices such as doors, overcasts, regulators, etc. Every mine, large or shall, coal or metal, should from the outset be equipped with a fan. While much has been written about natural ventilation and many claims have been made that in specific mines there is sufficient natural al" flow, there are few if any mines, coal or metal, where natural ventilation supplies anything like adequately safe or healthful conditions for underground workers even at ordinary times; and at a time of mine fire or explosion the mines depending upon natural ventilation are practically helpless, and certainly are decidedly dangerous to those unfortunates forced to be in them.

Jan 1, 1933

By J. W. Eckerd

The crushing of chestnut-size (1-5/8 by 13/16 inch) Pennsylvania anthracite in four commercial crushers (impact) jaw) hammer-mill) and gyratory types) was studied by the Bureau of Mines to determine which could produce the largest proportions of buckwheat Nos. 1 and 2 sizes (9/16 by 3/16 inch). Single pass dry and wet crushing techniques and the effect of stage crushing were evaluated. Calculations were made to show the effect of closed-circuit reduction on production rates and yield of the various sizes. The data show that the gyratory crushers produced the greatest percentage of the desired sizes. A ring-type hammer mill produced the greatest tonnage of buckwheat No.1 and rice (14.9 tons per hr.) during dry grinding tests) but the yield of these sizes was only about 55 percent) as compared with 62 to 70 percent for the gyratory crushers. The impact and jaw crushers produced the smallest amount of buckwheat and rice and the largest quantity of oversize material.

Jan 1, 1960