Search Documents

By Jeran Paul W., Michael A. Trevits

Subsidence data gathered by the U.S. Bureau of Mines over a series of longwall panels in the Pittsburgh Coalbed were studied to obtain insight as to the role of time in the subsidence process. It was found that subsidence began essentially with undermining and was completed within 1 year. The progress of the subsidence was dependent upon location above the panel. Subsidence in the central area of the subsidence trough, where subsidence is the greatest, was about 90 pct complete by the time the face had progressed a distance equal to one overburden thickness beyond a particular surface point. For a point over the rib of the longwall panel, the subsidence was only about 60 pct complete at this time. Data from three other sites in the northern Appalachian Coal Basin were analyzed to determine if an anomaly or the true characteristics of the subsidence process had been observed. All sites behaved similarly in the central portion of the subsidence trough. However, the subsidence of points over and adjacent to the ribs of the longwall panels was site specific. The fact that movement across the width of the panel was not uniform should be taken into account in assessing damages or the potential for damages resulting from mining-induced subsidence.

Jan 1, 1995

By R. H. Nielsen

A new, cheaper precipitation scheme has been developed to produce purified zirconium oxide, Technical-grade sulfuric acid is used to precipitate a basic zirconium sulfate from a hot dilute hydrochloric acid solution. With close control of temperature, pH, and zirconium - sulfate ratio, excellent purification and complete zirconium recovery can be attained. The process has been successfully applied for 3 months and has proved to be a more satisfactory procedure than the ammonium phthalate process used previously. INTRODUCTION The Northwest Electrodevelopment Laboratory of the Federal Bureau of Mines has developed and improved the Kroll process for the production of pure ductile zirconium and hafnium. metal. Since 1946 over 1 million pounds of zirconium sponge metal has been produced, mostly high-purity material for the Atomic Energy Commission

Jan 1, 1956

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine the embedded hydrogen chloride (HCI) and smoke particle characteristics during combustion of polyvinyl chloride (PVC) and chlorinated mine materials for development of a test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 250° and 1,000° C, for a 14-min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were hydrogen chloride embedded on smoke particles, hydrogen chloride concentrations in the gas phase, smoke particle average diameter (dg) and particle concentration (no), and product of smoke particle diameter and concentration (dgno). Other variables included carbon monoxide (CO), carbon dioxide (CO2), and oxygen (O2) concentrations; sample mass weight loss; and furnace temperatures. Results show that there is a correlation between embedded hydrogen chloride, hydrogen chloride gas concentrations, and inverse of the smoke particle diameter-concentration product (1/dgno); the higher the hydrogen chloride gas concentrations, the higher the embedded hydrogen chloride, the higher the 1/(dgno) values. These correlations will enable development of a simple test parameter to assess the toxic hazard that these materials pose during fire.

Jan 1, 2010

By E. P. Youngman

The mining law of May 16, 1884, is still the basic mining legislation in Smeden. To satisfy a demand for a revision of the entire mining law, special commissions have been at work for a number of years; but present indications are that the work will require several more years for its completion. The changes contemplated would affect mainly the relations between the nine operator and the landemer, as the present law, according to general opinion, tends unduly to jeopardize the landowner's right in favor of the miner. The socialist party desires additional changes, especially in the direction of giving more direct control of the industry to the State, a control that it now seems to exercise through individual agreements with mining companies. Its control of the Lapland iron mines comes through its sharing the ownership with the Luossavaara-iirunavaara Altb. In this instance, the Government should be Considered as a private commercial body, since the agreement with the company

Apr 1, 1933

By Thomas Fraser

About 24 per cent of our total production of bituminous coal is used in industrial power plants. As regards fuel conservation, therefore, the recovery of unburned fuel from furnace refuse presents interesting possibilities. Considerable attention has been given to this problem in the past, but because of the comparatively low initial cost of power plant fuel in the pre-war period little progress, has been made in this direction in the United States. Because of the higher price of coal in Europe more attention has there been given to the problem. In Germany a process has been developed for separating unburned coal in refuse by using an electromagnetic separator In the United States the use of mechanical stokers enabled low-priced screenings of high ash content to be used, so that even with relatively high percentages of combustible material remaining in the refuse, the loss in money is not excessive. If the price of screenings returns to the pre-war level around $1.00 per ton the process proposed here will probably not be especially interesting, except where the freight charges are very high. However, if the price of delivered coal continues high, such a process should result in considerable saving. The cost of continuous operation of such a refuse treating plant should not exceed 75 cents per ton of fuel recovered.

Jan 1, 1921

Reduce longwall shearer operator's dust exposure by selecting the best drum water spray sys-tem for minimizing dust generated durinq cutting. Approach Three of the most commonly-used drum water spray systems were installed on the same set of shearer drums and compared to determine which system best suppresses dust. The spray systems studied were: ? pick-point flushing ? cavity filling ? water-through-the-it Instantaneous and gravimetric sampling instruments were used to measure the respirable dust exposures of the shearer operators and dust concentrations downwind of the shearer. The Three Systems: Longwall shearer drums are routinely equipped with internal drum spray systems since these systems have been shown to be more efficient than external systems in terms of dust suppression per gallon of water applied. All U.S. longwall shearer faces utilize some type of internal water delivery spray system. The two most common systems are bit-or pick-point flushing and cavity filling. Pick-point flushing uses nozzles mounted in the bit blocks or in special blocks immediately in front of the bits. Cavity filling utilizes spray nozzles installed in a pipe manifold mounted on the drum hub between the scrolls or along the edge of the vane scrolls; water is sprayed radially from the manifold towards the adjacent vane scroll.

Jan 1, 1986

By E. C. Perkins

This report describes a ferric chloride trap, based on formation of a low-melting sodium chloride-ferric chloride mixture of near-eutectic composition, and its use in chlorination of impure titaniferous materials. The trap is placed in the hot gas stream between the chlorination reactor and the condenser. Virtually all of the iron is removed by the trap. The condensed titanium tetrachloride is free of suspended solids and contains only a trace of iron. Four examples are given of the use of the ferric chloride trap in chlorination of impure titaniferous materials. INTRODUCTION In the Kroll process, ductile titanium metal is produced by reducing titanium tetrachloride with magnesium metal.4/ In commercial practice, titanium tetrachloride is produced by chlorinating titaniferous materials in the presence of carbon.2/ In 1957 most producers were using rutile, and virtually all plants were designed for its use. About four-fifths of the domestic consumption of rutile was imported from Australia. The Bureau of Mines, under provisions of contract DMP-116 with the General Services Administration, studied electrosmelting of domestic ilmenites and titaniferous magnetites to produce high-titanium slags with pig iron as a byproduct. Under the same contract, chlorination studies also were being made of these slags. Smelting was done at the Northwest Electrodevelopment Experiment Station, Albany, Oreg., and chlorination at the Electrometallurgical Experiment Station, Boulder City, Nev.

Jan 1, 1958

By F. Chen, L. J. Gaydos, D. C. Kuhn, Demersm L. M., S. C. Sun

"Summary: In this report the differential regulation of NF-KB and nitric oxide (NO) was investigated in the mouse macrophage cell line RAW 264.7 following exposure to a mineral dust (silica) and /or an endotoxin (Lipopolysaccharide, LPS). The results indicated that silica and LPS can significantly induce the activation of NF-KB as well as elicit enhanced production of NO in RAW 264.7 cells as part of an early inflammatory response mechanism. A 24-hour time-course study showed that NO release from these cells continued to increase following the initial stimulus by LPS or silica. In contrast, activation of NF-KB was maximal at 6 hours and then showed a steady decline to 24 hours. The production of NO was suppressed by protease inhibitor and antioxidant, both of which block the activation of NF-KB. Surprisingly, the use of an NO synthase inhibitor resulted in an enhancement of NF-JCB activation. These findings suggest that NO produced in macrophage cells in response to an inflammatory stimulus like silica or LPS my be linked to a negative feedback role on the activation of NF-KB. It is now accepted that nitric oxide (NO) plays a pivotal role in the inflammation response process when macrophage cells are activated by a pro-inflammatory stimulus (l). Production of NO is dependent on the activity of the enzyme nitric oxide synthase (NOS). Up until now, at least three distinct genes have been described which encode different isoforms of NOS. NOS has been cloned from a variety of different mammalian cells, including constitutive neuron NOS, constitutive endothelium NOS and inducible NOS (2). Macrophages appear to be the principal cellular source for the inducible form of NOS (iNOS) activated in response to an inflammatory producing event. The mechanisms subserving the regulation of the iNOS gene and NO production have been under intense investigation in recent years (3-5). Several binding sites for transcriptional factors have been identified in the promoter region of iNOS gene, including NF-lCB, AP-1, NF-IL6, Oct-I to cite a few (5). NF-KB appears to play a"

Dec 1, 1996

By J. G. Walters

This bulletin presents, in collected and tabluated form, Bureau of Mines and American Gas Association (EM-AGA) carbonization data pertaining to the chemical analysis of tars and the characterization of tars and light oils obtained from U.S. coals.

Jan 1, 1967

By Donald O. Capstick

A mineral survey of the 520-acre Quigg West Wilderness Study Area (MT-074-155) was conducted by the U.S. Bureau of Mines in 1986 at the request of the U.S. Bureau of Land Management in order to evaluate its identified mineral resources. The Wilderness Study Area is in Granite County in western Montana about 16 miles northwest of Phillipsburg and 27 mi les northeast of Hamilton, MT. Stony Mountain, a study area on lands administered by the U.S. Forest Service, is about 1 mile to the south-southwest and was studied concurrently. No mineral resources were identified in the Quigg West Wilderness Study Area, but high grade gold assays, as much as 1.24 ounce gold per ton, were obtained at the one prospect found. Samples from four workings contained significant gold; minor silver, molybdenum, and copper were also present. The prospect containing the narrow and discontinuous gold-bearing quartz vein straddles the south boundary of the Wilderness Study Area. The shear zone containing the vein projects toward the old Crescent mine, about 4.5 miles to the south, which shows a similar geologic structure.

Jan 1, 1987

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

Develop a reliable, portable device for non-destructively testing the support integrity of a friction rock support (commonly referred to as a Split Set ). Approach The friction rock support, used to support mine roof and ribs, is a slotted tube driven into a drilled hole of smaller diameter. Upon installation, the tube is compressed radially. The amount of compression is a function of the hole diameter, the strength of the host rock, and the properties of the split set itself. A simple lightweight self-contained device was developed to determine the pull-out resistance of the friction rock supports in-situ, based on measurements of the tube's deformation. The tester measures the com-pressed internal volume of the slotted tube, which has been found to provide an estimate of the support's resistance to pull out. How It Works The tester consists of a pump and expander sections. The expander sections are made from an elastomer membrane which is stretched over two cores, each one inch in diameter and twelve inches long. The expanders are connected by a flexible coupler so that they can fit any alignment of the support.

Jan 1, 1984

By Albert J. Rambosek

The objective was to obtain qualitative information on (1 ) the stress field in a core stub at the bottom, or face , of a cored borehole and (2 ) whether , and at what distance , in terms of core diameters from the face of the borehole , relief of stresses in the core is complete . The photoelastic and brittle lacquer techniques of stress analysis were used to determine the pattern of stresses in two- dimensional models , simulating the bottom of a borehole with a projecting stub of core . The core was stress- free at 1-1 /2 core diameters or more from the face of the simulated borehole . The analyses of the isoclinic and isochromatic patterns in the core near the face of the borehole reveal why core occasionally breaks into thin plates , when core or stress - relief drilling is attempted in highly stressed rock masses , such as heavily loaded mine pillars . stub broke away from the bottom in a hydrostatically loaded artificial rock specimen in a manner indicating that core " wafering" can result from tensile stresses developed in the core when a coring bit penetrates the highly stressed rock mass .

Jan 1, 1964

By C. O. Hawk

As an exploratory effort to produce useful products from coal by a new path, the Bureau has made a few experiments on the fast heating of finely ground coal particles by irradiation with a flash of high intensity light. The flash was produced by an electrical discharge at high voltage through a xenon-filled tube. The flashes lasted from 2 to 3 milliseconds. The reaction took place in small sample tubes, ½ inch-dimeter by 4 inches long, and with small amounts of coal (total amount charged 0.1 gram, probable effective amount not more than 20 milligrams). Average particle size of the coal, estimated on a numerical basis, was 20 microns. Temperatures reached were evidently quite high, because all products obtained in quantity were characteristic of high temperature pyrolysis. Apparently, conversion of the coal was extensive where isolated particles received the full benefit of a flash. It seems particularly significant that acetylene was present in appreciable amounts--comprising almost 3 percent of the total gaseous product in one case. This is good evidence of a short heating period to very high temperature (well above 1,000° C) followed by rapid quenching. Although the results are interesting, they do not suggest any immediate practical application.

Jan 1, 1963

By J. P. McGee

As part of a joint U.S. Atomic Energy Commission-Federal Bureau of Mines program for using nuclear energy to supply process heat, a simulated nuclear loop has been constructed to test components. This loop has been operated for more than 1,800 hours at 100 p.s.i.g. Of this period, 23 hours were at 2,500° F. and higher; 540 at 2,000° to 2,500° F.; 840 at 1,500° to 2,000° F.; 200 at 1,000° to 1,500° F.; and 260 below 1,000° F. Leakage at flanges and welds was not a serious problem. A helium-recycle system with gas temperatures of 2,300° to 2,500° F. and a static pressure of 250 p.s.i.g. appears feasible. Difficulties were encountered with the recycle compressor due to thermal distortion of the impeller and shaft. The use of sealed bearings limits compressor operation to the life of the bearings.

Jan 1, 1960

By Philip E. Sanker

The Bureau of Mines conducted small-scale batch and semicontinuous tests on the reduction of zinc sulfide with iron according to the reaction ZnS + Fe ? FeS + Zn to determine reaction kinetics in the temperature range 1,000° to 1,400° C and to investigate the potential use of a scrap iron reductant. Batch tests indicated that a temperature of at least 1,300° C with a 1:1 mole ratio of Fe to ZnS is needed for good zinc recovery. Semicontinuous tests were conducted, using four zinc concentrate samples, containing various percentages of copper, cadmium, and lead, which were reacted with iron and iron contaminated with iron oxide and tin in an externally heated graphite furnace. Analysis of the zinc metal and FeS matte reaction products showed cadmium to be entirely in the zinc metal, copper to be in the FeS matte, and lead to be about 60 pct in the zinc metal and 40 pct in the matte. Tin reported to the matte, and none was detected above the O.OS-pct level in the zinc. Sulfur dioxide was not detected in the offgas when up to 20 pct of the iron was replaced by Fe203.

Jan 1, 1976

By L. E. Schultze

[The Bureau of Mines conducted bench-scale studies to develop techniques for stripping tetravalent cerium from tri-n-butyl phosphate solutions. Experiments were conducted in a constant-temperature bath using beakers and mechanical stirring. Ninety-five pct of the cerium was stripped from a 50-pct tri-n-butyl phosphate 50-pct kerosene solution containing 0.18 M cerium in 15 minutes at 50° C using 0.11 M aqueous formaldehyde.]

Jan 1, 1974

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) spin trapping methodology has been used to study the reactions of manganese dusts with glutathione, employing a-{4-pyridyl-1-oxide)·N-tert-butyl-nitrone (PBN) and 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) as spin traps. The results show evidence for the glutathionyl radical formation in the reactions of both MnO2 and manganese (Ill) acetate with glutathione. Based on these experimental observations, we hypothesise that the mechanism of neurotoxic effects of manganese might be due to the fact that the generation of glutathionyl radicals depletes the glutathione pool and reduces the glutathione shield against free radical products of dopamine metabolism and manganese induced reactive oxygenated species. IntroductionExposure to manganese compounds often occurs as the result of foundries and mining operations (1. 2). Other significant sources of environmental manganese include coal-fired power plants and burning of residual and crude oil (3, 4). Lately gasoline combustion has also started to contribute since manganese (methyl cyclopentadienyl manganese tricarbonyl. 0. 125 g/gallon) is being used instead of lead as an antiknock ingredient in automobile fuels (5. 6). Although manganese is an essential element in certain biological processes it is toxic in excessive amounts. The manganese toxicity is mainly associated with the nervous system (7-9). Symptoms frequently observed in manganese poisoning or manganism are disorientation, memory loss, anxiety, compulsive laughing and crying, mask-like faces, akincsia rigidity and tremor (10). In spite of numerous investigations to understand the mechanism of manganese induced injury. it has not been possible to localize the initial chemical lesion responsible for altered physiology and ultimate cell death. This may perhaps he the reason for failure in developing a successful therapy for manganese intoxication."

Jan 1, 1990

By N. S. Dalal, B. Jafari, F. H. Y. Green, M. M. Suryan, V. Vallyathan

"Freshly ground and aged anthracite and bituminous coal samples were investigated by electron spin resonance (ESR) spectroscopy to detect the presence, concentration and reactivity of free radicals. Freshly ground anthracite coal produced greater concentration of free radicals than the bituminous coal, and the radical reactivity was also greater for the anthracite. The reactivity of the newly produced free radicals in the anthracite dust correlated with the dust's toxicity. Furthermore similar coal-based free radicals were detected in the lung tissue of autopsied coal miners, suggestive of persistent reactivity by the embedded coal dust leading to the progressive disease process. Results of the studies on the severity of coal workers' pneumoconiosis (CWP) and free radical concentration m lung tissue support this hypothesis.INTRODUCTIONCOAL WORKERS' PNEUMOCONIOSIS (CWP) has been an important topic of concern to miners, mining engineers, epidemiologists and medical researchers for decades. It is well known that the prevalence and severity of CWP differ markedly between different regions and mines despite comparable exposures to respirable dust (REISNER and RoBOCK, 1977; HURLEY et al., 1979). These variations in pathogenicity of coal mine dusts can only partially be explained by differences in the mineral composition and by rank of coal (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). Cytotoxity studies on mammalian cells do not correspond well with the human disease pattern (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al.,1980; VALL YA THAN et al., 1988). For example, while epidemiological studies of coal miners (REISNER and ROBECK, 1977; HURLEY et al., 1979) indicate that the prevalence of CWP correlates roughly with the rank of coal, such correlation has not yet been established in biological studies, despite considerable effort (CHRISTIAN and NELSON, 1978; CHRISTIAN et al., 1979; HATCH et al., 1980). In order to help resolve this apparent paradox we have undertaken a systematic study to evaluate whether any correlation exists between the concentration of free radicals present in fresh or aged coal dusts from two well-characterized U.S. coals. This study was also prompted in part by observations reported in the literature that organic free radicals can be formed on the surface of freshly fractured coals (LEBEDEV et al., 1978; DULIBA and CLARKSON, 1984). In particular, ARTEMOV and REZNIK (1980) noted that the decay lifetimes and, hence, the reactivity of the organic free radicals formed on crushing Russian coals, .depended"

Jan 1, 1989