Search Documents

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By Jon C. Volkwein

The U.S. Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low-profile mining machine. Tests were conducted in a full-scale model mine using a continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters tested included mining position, depth of cut, brattice setback, and combinations of scrubber, and directional or symmetrical sprays. Results indicated that either water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 20-ft blowing curtain without sprays. No FVE values were less than the standard 20-ft blowing results.

Jan 1, 1989

By Bill Linville

During calendar year 1972, the Bureau of Mines was engaged in some 20 major areas of research for the development of new and improved efficient methods of conservation and utilization for petroleum and natural gas, oil shale, and coal. Made up of numerous projects described in this report, the program was carried out through research performed at research centers and laboratories in the field supervised and supported by administrative personnel of this Bureau of the Department of the Interior. Based un this research, 186 technical reports were published by the Bureau or others, and numerous other reports were prepared for Federal agencies, State agencies, and organizations engaged in cooperative research programs with the Bureau.

Jan 1, 1973

By A. T. Coumbe, I. F. Avery

The Bureau of Mines has completed a survey of petroleum pipe - lines by direct correspondence with the oil companies and the use of the records of the Interstate Commerce Commission in order to cover both interstate and intrastate systems . The review shows that crude petroleum and product pipe -lines in the United States had a total length of 152,814 miles on January 1 , 1950 , an increase of 25,463 miles since May 1 , 1941 , the time of the last previous survey . The expansion in pipe -line systems was due largely to new trunk-line construction , as the mileage built to carry refined products increased by 11,880 miles , and those intended for crude -oil transportation gained 6,193 miles . Trunk lines represented 60 percent of all pipe -line mileage on January 1 , 1950 , compared with 58 percent in 1941 . The average diameter of trunk -lines for crude oil , as calculated on the various sizes and weighted according to their respective lengths , increased to 9.8 inches on January 1 , 1950 , compared with 8.4 inches on May 1 , 1941. The mileage for lines up to 8 inches used in crude trunklines has decreased since the 1941 survey , while those of larger sizes have increased . The extensive use of large- diameter oil pipe -lines has developed since the construction of two major lines from Texas to the East Coast at government expense as a World War II emergency measure . The successful operation of these lines proved their economic advantages over smallerdiameter lines as well as their effectiveness in moving unprecedented volumes of oil during the period when tanker movements were restricted by submarine action in the Atlantic Ocean . The 24-inch diameter " Big Inch " line carries over 300,000 barrels daily of crude oil , and the 20 -inch " Little Big Inch " carried over 230,000 barrels daily of gasoline and light fuel oils to destinations where they were urgently needed . Hence , Although these lines were sold and converted to natural -gas service in December 1946 , after fulfilling their wartime mission , their record proved to the industry that significantly lower operating and investment costs per barrel -mile of oil moved could be achieved than were possible with the comparatively small lines in general use up to that time . the several major oil pipe -line projects that have been constructed since the late war are of large diameter pipe . To assure supplies and market outlets of sufficient magnitude to support such lines and provide adequate flexibility , ownership is often shared by several large companies whose transport needs are served in common . The principal recent expansion in facilities has been from supply points in Southwestern States toward markets in the North and East and to Gulf tidewater .

Dec 1, 1950

By Robert L. Rough, William E. Eckard

Laboratory data obtained from a Bureau of Mines rotary air core of a well near Sugar Grove , Warren County , Pa . , were instrumental in initiating hydraulic fracturing in the area to stimulate oil recovery from Glade sand oil reservoirs . This report outlines the general geology , lease development , reservoir- rock characteristics , and oil - production history of Glade and Clarendon sand reservoirs in Warren County . The methods of well completion for single- stage and multiple- stage hydraulic fracturing of old and new wells are discussed , and a range of hydraulic fracture treatment data from 29 Glade sand and 10 Clarendon sand wells is presented . A composite decline curve representing oil - production data from six wells shows probable results of hydraulic fracturing . Average cumulative oil production during the first 100 days after hydraulic fracturing with a sand - carrying liquid is compared with production after conventional shooting with liquid nitroglycerin .

Jan 1, 1964

By James J. Snodgrass

The Bureau of Mines has investigated vibration levels produced by blasting at four underground sites to establish how such factors as type of explosive, delay blasting, charge weight, and geology affect amplitudes of ground motion. A summary of the work is presented and the results of further analysis of the data are discussed. Square root scaling was found applicable to two of the underground sites and could be applied with minor error to all the sites. Comparison of empirical propagation equations in the different rock types indicates that although the site effect is apparent, the combined data may be used as a basis for engineering estimates of vibration amplitudes from subsurface blasting in many different rock types. Recommendations for predicting and minimizing vibration amplitudes from underground blasts are given.

Jan 1, 1974

By L. A. Eros

The U.S. Bureau of Mines and Western Fuels Utah, Inc. entered into an agreement to plan, install, and evaluate a micro-computer based monitoring and control system at Deserado Mine, an underground coal mine. The U.S. Bureau of Hines contracted the Colorado School of Mines (CSN) to independently evaluate the project. CSM evaluated and documented costs, benefits, problems, and management and labor perceptions in this report. Recommendations are provided for mine operators and monitoring system vendors considering future installations.

Jan 1, 1986

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Russell J. Foster

In this Bureau of Mines report a selection process has identified 14 nonstockpiled materials (cesium, gallium, hafnium, indium, osmium, rhenium, rhodium, rubidium, ruthenium, scandium, selenium, tellurium, thallium, and zirconium) that are linked to the continuing evolution of high-technology fields such as electronics, catalysis, and energy, and that have limiting factors associated with domestic availability. A qualitative assessment of the "potential criticality" of these materials was made through a consideration of end uses, demand trends and forecasts, production, mineral reserves, byproduct status, alternative supply sources, substitution and conservation options, and recyclability.

Jan 1, 1988

By Lincoln A. Stewart

"INTRODUCTION The First Supplemental National Defense Appropriation Act, approved August, 25,, 1941, authorized the Bureau of Mines to investigate sources of raw, material for western production and appropriated funds for that purpose. Numerous iron deposits and prospects in the Western States were investigated. Among those selected for more detailed investigation were tile Apache and Chodiski deposits in Arizona.The United States Geological Survey had examined these deposits in 1929 3/ and estimated that ""the quantity of minable ore reasonably to be expected in this locality will reach 10,000,000 long tons, but it will require prospecting by core drill to demonstrate this quantity with certainty"". C. H. Johnson, a mining engineer of the Bureau of Mines, made a preliminary examination in October 1941 and proposed exploration of the Apache deposit Canyon Creek.A trench sampling project was set up, and work at the Apache deposit commenced in November 1941. Mapping, trenching, and sampling of outcrops was completed in March 1942. Trenches were laid out at approximately 200-foot intervals for about 9,200 feet along the iron outcrop east of Canyon Creek, and channel samples were taken across the iron formation. The outcrop also was explored by trenching and sampling along a 1,900-foot outcrop on the west side of Canyon Creek.The first diamond-drilling campaign at Apache was initiated in May 1942 and continued to January 1943, when work was suspended owing to depletion of funds. Six holes spaced at approximately 500-foot intervals and, 500 feet back from the outcrop on the east side of Canyon Creek were drilled through the iron formation during this period.While this drilling was in progress, the Chediski deposit was mapped, trenched, and sampled. The trenches were spaced at intervals of approximately 800 feet along 10,000 feet of the iron-ore outcrop."

Jul 1, 1947

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind. limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941

By J. B. Clemmer

This report summarizes the results of u laboratory study of the beneficiation of Arkansas bauxite by flotation. Although the investigation is not yet completed, a preliminary retort of the results on several typical bauxites is presented to show the merits rind limitations of flotation for the production of concentrates acceptable to the aluminum industry. It is

Jan 1, 1941

By F. S. Crawford

This study was made to find methods of preventing back strains, among workers in brick plants, however, the information should apply to other industries that employ hand labor too process materials. The report is based on information in letters from. Bureau of Mines engineers and other safety men in the United States who visited numerous brick plants. Back strains, as wall as hernias and other muscular strains, result when certain body structures are subjected to strains greater than, they can withstand. Such breakdowns may be prevented simply by not straining these body structures. This is simple in theory but complicated in practice. It requires primary education of new workers and reeducation of older workers in the best method of lifting, preemployment physical. examinations to select employees for the jobs that require constant lifting, all possible mechanization of material-handling operations, relocation of machinery, and elevation of working surfaces to reduce to a minimum the muscular effort the workers must exert to perform operations impossible to mechanize. Accidents of any kind are a total bee for the American economy and decrease productivity; whereas mechanization raises the level of productivity and constitutes progress toward total safety. Heavy lifting should be done mechanically whenever possible, saving the men to direct the machines. This is an essential step in preventing strain accidents.

Jan 1, 1953

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By William F. Jahn

Because of the' situation in Europe during the summer of 1939, with the possibility of war and consequent curtailment or loss of supplies of tin to the United States, the Bureau of Mines undertook an investigation of domestic tin resources. This was permitted by the Strategic Minerals Act of 1939, which authorized investigation of possible domestic resources of strategic minerals necessary in a national emergency. The minerals selected were in short supply, and the United States depended almost entirely on imports to meet normal requirements. The Black Hills of South Dakota were selected for investigation as one possible source of tin because of the occurrence of the mineral there has been known since 1876, although production had never been important. The Tinton area, in the northern part of the Hills, had received the most attention and contained some minor indicated and inferred tin deposits.

Jan 1, 1949

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or non- volatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this report. Data mere obtained, on application of such locomotives to cod mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By Sheridan J. Rodgers

Improved methods of dust control in the metal and nonmetal mining industries were studied. Preliminary dust surveys were made at selected mines and three mines were chosen for additional studies. Dust control effectiveness was evaluated using full shift gravimetric sampling and GCA Dust Monitor readings. Analyses for free silica content and particle size distribution were conducted. A belt washing system which was used to control dust at a transfer point was evaluated. The average reduction of respirable dust was 48% and the average reduction of total dust was 78%. The belt washing system not only maintained the work place within compliance but reduced maintenance problems along the beltway by 90%. Exhaust ventilation at a crusher was evaluated for control effectiveness. Ventilation along with operation of the crusher control room under slight positive pressure, maintained the work place within compliance. An exhaust ventilation system was designed for use at an underground rotary dump. Although the system was not installed or evaluated, details on the design are given. High expansion foam was used at an ore chute in an attempt to control dust at the draw point and loading point. Results indicated that foam did not effectively control dust.

Jan 1, 1978

By George S. Rice

In response to numerous requests for information as to the status of internal-combustion mine locomotives of the Diesel type that use heavy or nonvolatile oil for fuel, with special reference to their safe use in coal mines, the United States Bureau of Mines is issuing this t port. Data were obtained on application of such locomotives to coal mining only in Belgium, France, Germany, and Great Britain. The locomotives are used in coal mining in other countries, as well as in potash, iron, and other kinds of mining, but their chief development has been in coal mining in Germany, France, and Belgium. Recently popular interest in the Diesel type of engine for motive purposes was aroused in this country by the successful application of Diesel engines to railroad locomotives hauling fast transcontinental trains, and, according to published statements, at a low cost of fuel per mile of run.

Jan 1, 1936

By R. W. Stahl

Methane, a highly explosive gas evolved during the coal-formation process, is one of the hazards of mining most difficult to overcome. It is retained between particles of coal and entrapped in strata overlying and underlying the coal beds to a degree dependent upon the permeability of the enclosing strata. Considering that methane might be encountered at any time during the mining of coal, attempts have been made through the years to minimize the sources of ignition at coal-mine faces, such as the introduction of permissible electric equipment, the prohibition of smoking and open lights, and the development of safer explosives. The sparks created when mining-machine picks contact sandstone or iron pyrites2/ constitute one source of ignition, always recognized as a possibility but never greatly emphasized in the United States until recently, when ignitions began occurring with rather alarming frequency and in widely scattered coal-producing areas.

Jan 1, 1956

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980