Search Documents

By P. N. Vernon

Ausmelt top entry submerged lance technology offers a cost-effective means of carrying out a range of base metal smelting operations with minimum impact on the environment. The system is capable of using a range of fuels depending upon local costs. Due to the intense, localised reaction zone, high energy efficiency is obtained and the physical size of the plant is relatively small compared to that of most competing technologies. Capital cost can thereby be minimised. The furnace is well enclosed, such that fugitive emissions and ingress of diluting air to the gas stream are both minimised. The oxygen potential in the slag can be varied over a wide range such that the system can be applied in both oxidising and reducing duties. Following a general description of the technology, the paper discusses Ausmelt plants already in operation. The application of the technology for the provision of additional smelting capacity, for the improvement of converting operations and for slag cleaning is then described. A brief explanation of how these processes could be applied at southern African smelters is given and the paper closes with an assessment of novel Ausmelt applications for this geographical region, such as zinc recovery from sulphides.

Jan 1, 1997

By B. Das

he flotation studies on hematite were carried out using di (2-ethylhexyl) Phosphoric acid (D2EHPA) as the collector. The possible mineral reagent interaction was studied through electrokinetic and dissolution studies. The shift in zeta potential (PZC) and decrease in dissolution of iron in the presence of D2EHPA indicated that D2EHPA was specifically adsorbed on hematite surface. The adsorption imparted necessary hydrophobicity for flotation of hematite. Hematite could be floated selectively from hematite and quartz synthetic mixture. Key words: Hematite, D2EHPA, flotation, electrokinetics, dissolution.

Jan 1, 2003

By Ö. Uysal

This study deals with the presentation of the mechanized longwall mining project introduced some years ago to increase productivity and output of Aegean Lignite Establishment (ELI) owned by Turkish Coal Enterprises (TKI.) and the comparison of this method with a planned alternative new mining method called ?shortwall mining? where continuous miners will be introduced as primary coal excavation machines. Following the planning phase, production costs have been calculated for both mining methods on the basis of a panel having a height of 7.5 m. In addition to cost analysis, both methods have been evaluated using ?the multi-dimensional objective system?. In this evaluation the value synthesis has been carried out according to scoring models. Lastly, the advantages and disadvantages of both production methods have been stated by analysing them according to related criteria. In the light of outputs gathered from the analyses, it has been determined that the shortwall mining method will out perform the longwall method. Keywords: continuous miner, shortwall mining, longwall mining, multi-dimensional objective system.

Jan 1, 2006

By B. Tiryaki

Performance prediction models for partial face mechanical excavators, when developed in laboratory conditions, depend on relating the results of a set of rock property tests and indices to specific cutting energy (SE) for various rock types. There exist some studies in the literature aiming to correlate the geotechnical properties of intact rocks with the SE, especially for massive and widely jointed rock environments. However, those including direct and/or indirect measures of rock fracture parameters such as rock brittleness and fracture toughness, along with the other rock parameters expressing different aspects of rock behavior under drag tools (picks), are rather limited. With this study, it was aimed to investigate the relationships between the indirect measures of rock brittleness and fracture toughness and the SE depending on the results of a new and two previous linear rock cutting programmes. Relationships between the SE, rock strength parameters, and the rock index tests have also been investigated in this study. Sandstone samples taken from the different fields around Ankara, Turkey were used in the new testing programme. Detailed mineralogical analyses, petrographic studies, and rock mechanics and rock cutting tests were performed on these selected sandstone specimens. The assessment of rock cuttability was based on the SE. Three different brittleness indices (B1, B2, andB4) were calculated for sandstones samples, whereas a toughness index (Ti), being developed by Atkinson et al.1, was employed to represent the indirect rock fracture toughness. The relationships between the SE and the large amounts of new data obtained from the mineralogical analyses, petrographic studies, rock mechanics, and linear rock cutting tests were evaluated by using bivariate correlation and curve fitting techniques, variance analysis, and Student?s t-test. Rock cutting and rock property testing data that came from well-known studies of McFeat-Smith and Fowell2andRoxborough and Philips3have also been employed in statistical analyses together with the new data. Laboratory tests and subsequent analyses revealed that there were close correlations between the SE and B4 whereas no statistically significant correlation has been found between the SE and Ti. Uniaxial compressive and Brazilian tensile strengths and Shore scleroscope hardness of sandstones also exhibited strong relationships with the SE. NCB cone indenter test had the greatest influence on the SE among the other engineering properties of rocks, confirming the previous studies in rock cutting and mechanical excavation. Therefore, it was recommended to employ easy-to-use index tests of NCB cone indenter and Shore scleroscope in the estimation of laboratory SE of sandstones ranging from very low to high strengths in the absence of a rock cutting rig to measure it until the easy-to-use universal measures of the rock brittleness and especially the rock fracture toughness, being an intrinsic rock property, are developed.

Jan 1, 2006

By B. McCosker

The choice of the appropriate delivery process for a project is often not adequately thought about. The industry needs to be prepared to break its preconceived mind-sets on delivery procedures. Industry should also be prepared, on a project by project basis, to commit to a critical review as to how the assessment and then selection of the best procurement method can best optimize the project outcome for both client and contractor. Conventional standards and biased reliances and experienced based preferences should be challenged. To achieve this requires a paradigm shift in attitude to both the process of tendering and the evaluation of tenders. Tender and contracting practices are dynamic and have moved away from solely cost based assessments. Tendering contracts arise imposing changed duties upon owners. Traditional contract delivery models have shifted, reflected in part by the trend towards relationship contracting. The categories of contract options are not closed. Many are but hybrids of other time-tested models. This paper considers options available for any brownfield or greenfield project. The principles outlined are translatable to supply, upgrade, operation and maintenance arrangements.

Jan 1, 2002

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, thereby lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within 5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3D multi-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2007

By I. Jones

Geologists, engineers, technicians and surveyors have successfully utilized technical software in the mining industry for over 30 years. Software for processing survey, geology, mine engineering and planning information make these functions more efficient by automating repetitive tasks and reducing data processing errors. While these systems have been improved incrementally overtime, new systems that represent giant leaps in technology have been introduced to help mining operations increase productivity and reduce costs. However, their widespread use within the industry has left individual companies without a competitive advantage. Additionally, the ability of these applications to provide the productivity improvements required in today’s uncertain market conditions has since peaked. The next wave of technology—integration of independent software applications—is just starting to emerge and will have a significant effect on the productivity of mining operations. To reap the productivity gains required to remain competitive, mining companies must exploit the collective knowledge and experience of every employee in the organization. Integration of independent software application allows companies to leverage information from all activities, enabling staff to make better decisions to improve productivity. This paper outlines the importance of integration as productivity enabler. Key performance indicators, strategic mine planning, resources management and mine-to-mill integration are discussed as processes that enable productivity. The Gemcom Enterprise Mining System (GEMS)is introduced as the industry’s first integrated solution that enables these productive processes. The paper concludes with a comment on the level of change required to realize the benefits of integration.

Jan 1, 2003

By F. Sawyerr

A bubble population balance model is proposed for the prediction of Sauter mean bubble diameters in mechanical flotation cells. In the model, the flotation cell is treated as two separate, statistically homogeneous zones?the impeller zone, and the bulk tank zone. Balance functions for the rates of bubble breakage, coalescence, recirculation and inlet-outlet events are proposed based on classical chemical engineering research in two- and three-phase fluid mixing systems. An initial simulation of the population balance model shows trends in bubble size distributions comparable to measured distributions in industrial mechanical flotation cells.

Jan 1, 1998

Council for 2003/2004 President T.R. Stacey President-elect F. M. G. Egerton Vice-presidents Senior W. H. van Niekerk Junior R.P.H. Willis Immediate Past-president S.J. Ramokgopa Honorary Treasurer J.A. Cruise

Jan 1, 2004

By L. Munsamy, B. J. Madden

OpenRisk, an open cast risk rating system, takes into account relative differences in the importance of hazards, as experienced on each mine as a result of different combinations of geotechnical factors and mining conditions. The system is based on critical geotechnical and operational parameters that have been identified by mining personnel and rock engineers. The primary advantage of this risk rating system is that all the strip mines would use an identical system, which enables the user to compare their risk to the risk at neighbouring mines and/or other open cast mines. The system can be adjusted to meet local, mine specific requirements. This system has been made practical and easy to use. Therefore, this tool can be used by personnel from other disciplines not directly related to rock engineering. OpenRisk system has been in operation at nine Anglo Coal and other open cast mines. It adequately detects areas of high risk and generates adequate remedial solutions to reduce the risks. Awareness of the personnel has been higher at the sites that use OpenRisk. The proactive approach of OpenRisk ensures that all personnel are aware of risks in the pits and how to deal with potential risky areas.

Jan 1, 2006

By N. R. Shoko, J. Chirasha

Zimbabwe Alloys has been producing Low Carbon Ferrochrome since 1953. A number of operational and technical advances have been made since then. Some of these advances improved production significantly. Process control, however, remained a challenge not only in the production process itself but also in the handling of finished product. In addition the handling of the slag created an environmental problem. Process control issues were addressed by Zimbabwe Alloys Limited and Japan Metal & Chemicals (JMC) entering into a Technical Transfer Agreement. The aim of the technical transfer was to improve production, alloy quality and, thereby, the financial performance of Zimbabwe Alloys. In addition, the Low Carbon Ferrochrome production process was made environmentally friendlier by modifying the final slag handling methodology. The aspects that are covered and discussed in this paper are, ladle refractory lining changes, improved control of the process, changes in the alloy casting methodology and granulation of the final slag. The improved control of the process was enhanced by the conversion from ladle duplexing to argon purging, introduction of on-line sampling and introduction of second stage process. The combined effect of the above was a significant improvement on on-grade material production, production efficiencies, unit cost of production and a cleaner working environment.

Jan 1, 2004

By R. Banda

This paper describes the decision to implement and then the implementation itself, through trials, of electronic ?Smartdets? over previously used shock tubes. It concludes that Mufulira Mine has become the first mine in Zambia to convert 100% of its stoping to ?Smartdets?, because the Mine?s management was prepared to look beyond the unit cost of product and were ready to look at the broader picture of cost effectiveness and increased productivity.

Jan 1, 2005

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By A. A. B. Douglas

In this paper the origins of the mortar intruded concrete concept and its development and application in the construction of watertight bulkheads in South Africa are described. The events leading to the commissioning and execution of the West Driefontein Experimental Plug and the Virginia/Merriespruit Boundary Plugs, and their roles in the proving of the technique, follow. The development of the first Transvaal and Orange Free State Chamber of Mines Code of Practice for Mortar Intrusion Concrete for Underground Plugs and Bulkheads, Johannesburg, November 1962,is explained. The saga of the October 1968 flood and subsequent salvage of the West Driefontein Gold Mine is recounted. The paper concludes with mention of the validation programme carried out for the Placer Dome Western Areas Joint Venture and their South Deep water barrier programme.

Jan 1, 2006

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2 slags that are typically encountered in the production of manganese-containing stainless steels. A gas equilibration-quenching technique was employed in measuring the activities. Activities of Mn in Pt-Mn alloys were redetermined at 1600ºC, which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600ºC. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient regression models were developed to predict the activities and activity coefficients of MnO in slags at 1600ºC. Keywords: activity, MnO, slag

Jan 1, 2005

By B. M. Loftus

An investigation into the use of impinging stream (jet) reactors for the leaching of a free milling ore produced an increase in gold recovery by 10% while decreasing leaching time by up to 90%.Tests on refractory ores demonstrate no apparent improvement in recovery. However, leaching kinetics are dramatically increased when these ores are subjected to jet reaction prior to agitation.

Jan 1, 1997

By F. Peer

In most coal preparation processes, water is a necessary medium, but the presence of water in coal after it has been cleaned has a negative impact on transportation costs, handling and specific energy values. The utilization of super absorbent polymers (SAP) in the nappy application is well known. The concept of utilizing these polymers was investigated for the purposes of dewatering coal and other fines, generated by preparation processes such as flotation. SAPs are granular highly cross-linked synthetic copolymers with excellent water-absorbing properties. The dewatering process is characterized by three main stages: (a) contact of super absorbent polymer with high-moisture fine coal; (b) separation of dewatered fine coal from super absorbent polymer; and (c) regeneration of used super absorbent polymer, by exploiting its response to changes in conditions such as pH or temperature. Preliminary tests showed the separation step to be very difficult. The novel idea of encasing a given amount of polymer in a water permeable cloth solved this problem (of separating the swollen polymer from the dewatered coal). Preliminary tests investigating the effectiveness of the sachets of polymer showed a drastic decrease in the moisture contents of slurries. Furthermore, it was shown that it was possible to regenerate the polymer (still within the sachets) through thermal drying. A full-scale experimental programme was then followed to accurately determine the feasibility of using sachets of SAP. The experimental variables were initial slurry moisture content and polymer dosage. It was observed that the sachets seemed to work fastest and most effectively at high moistures and also at higher dosages of SAP. Regeneration of the polymer was also investigated, using two methods: thermal regeneration and pH-induced regeneration. The experimental variables, for investigating the regeneration process, were method of regeneration and grade of water used. Thermal regeneration at 70°C seemed to work successfully. Although the cost of using thermal energy is still a problem, the safety aspect (fire hazards) has been addressed since the polymer does not ignite when heated, unlike fine coal particles that may do so. The alternative method of regeneration, which exploits the pH-sensitivity of the polymer, was less successful, and further work needs to be conducted.

Jan 1, 2003

The unpaved road network on a surface mine is extensive, comprising numerous roads of varying construction and material qualities with highly variable traffic volumes. Existing haul road maintenance management systems (MMS) work well for predictable traffic volumes, but for complex mine road networks, the MMS becomes onerous. This results in sub-optimal road maintenance strategies with the attendant increase in total road-user costs and reduction in service. A real-time maintenance management system was thus sought to overcome the deficiencies of existing MMS for mine roads. Since most large mines operate trucks with on-board diagnostic data collation, linked through a centralized communication and GPS backbone, it was proposed that road condition could be monitored on a real-time basis through on-board vibration signature analysis. The aim of this paper is to present the development of a real-time mine haul road maintenance management system. Following are view of mine road maintenance practices, the real-time system architecture is introduced and the results of a field trial of on-board vibration signature assessment is presented. The trial results are discussed in the light of road defect signature recognition, analysis, signature repeatability and system limitations. This approach has applicability to other situations such as a network of district roads, subject to an analysis of the economic feasibility. The paper concludes that modern technology has the potential to apply maintenance as and where needed with possible reductions in authority cost and an improvement in service provided for the road user.

Jan 1, 2003

The slags produced by the Imperial Smelting Process (ISP) are based on the system ZnO-?FeO?-Al2O3-CaO-SiO2. The slag chemistry is important to the process since it determines the fluxing practice and the operating temperature of the furnace required to produce fluid slag. The paper presents the results of the first systematic experimental investigation of these ZnO-containing slags in equilibrium with metallic iron, and provides information on the primary phase fields and liquidus temperatures in these slags over the range of compositions used in ISP practice. A feature of the slags is the presence of alumina, which has a major influence instabilizing the spinel phase. This information presented in the form of pseudo-ternary sections ZnO-?FeO?-(Al2O3+CaO+SiO2) enabling the data to be readily used by plant engineers. Keywords: liquidus temperature, ISP, EPMA, ZnO-?FeO?-Al2O3-CaO-SiO2, phase equilibria.

Jan 1, 2004