Search Documents

By H. Ramazi, A. Amini

"This article is devoted to the introduction of a new technique of electrical resistivity data processing called residual resistivity (RR). We define RR as measured resistivity minus background resistivity. To determine the background resistivity, the data acquired from electrical resistivity measurements along a given survey line is evaluated, and then an equation is fitted to the data corresponding to a chosen measurement station as a function of current electrode spacing (or array length). The RR technique was applied to several synthetic models to compare the conventional resistivity inversion of each model with its RR-based inversion. A case study was carried out in a karstic area in Zarrinabad, Lorestan Province, western Iran, to detect the location and geometry of probable cavities by conventional resistivity inversion and RR-based inversion. The results showed that the anomalous zones are better highlighted in the RR-based inversion images in comparison with the conventional inversion images. In some cases, anomalies detected by the RR-based images were hidden in the conventional method. IntroductionThe geoelectrical resistivity method has been widely used since the early 20th century, and plays an important role in several fields such as groundwater and subsurface mineral exploration, geotechnical and environmental investigations, and archeological studies (Bayrak and Senel, 2012; Candansayar and Basokur, 2001; Fehdi et al., 2011; Hee et al., 2010; Osella et al., 2003; Wilkinson et al., 2010). The goal of geoelectrical resistivity surveys is to determine the distribution of subsurface resistivity by measuring the current-potential difference on the ground surface (Aizebeokhai et al., 2010). In the electrical resistivity method, an electrical current is injected into the ground by two electrodes, called current electrodes (AB), and the potential difference is measured between another pair of electrodes, the potential electrodes (MN). Several methods of interpretation are available for application to electrical resistivity data, the simplest being the graphical interpretation of the apparent electrical resistivity pseudo-sections along each survey line. A second method, electrical resistivity inversion, has been developed to create relatively accurate two- and threedimensional computational resistivity models of subsurface sections (Loke and Barker, 1996; Niwas and Mehrotra, 1997; Nordiana et al., 2014; Oldenburg and Li, 1994; Papadopoulos et al., 2009; Yilmaz and Narman, 2014). In the inversion method, models of subsurface objectives are mathematically inverted to reach optimal solutions subject to prescribed objective functions, constrains, and convergence criteria. A common problem when using the electrical resistivity inversion method is that the inversion model of an electrical resistivity profile may be non-unique because different inhomogeneities in the investigation media can result in the same electrical response (Smith and Vozzof, 1984)."

Jan 1, 2016

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

By Moraka N. V., van Rensburg M. Jansen

"SynopsisGoing beyond transformation claims contained in employment equity scorecards and industry compliance reports, this article provides qualitative insight into the initiatives employed and challenges experienced by mining companies in a quest to transform the mining industry. Perceptions expressed during in-depth interviews with 10 senior executives showed that the assumption that mining companies are reluctant to transform is erroneous. Results from this study suggest buy-in and commitment to transformation. This article describes specific initiatives undertaken by mining companies to transform. The most notable initiatives include staff recruitment efforts to appoint historically disadvantaged South Africans (HDSAs), staff development initiatives, as well as community development. The findings furthermore contextualize the challenges experienced by industry participants in their quest to transform. Despite accusations that industry participants are not taking responsibility for the implementation of the transformation agenda, government needs to recognize that they too have a role to play and need to appreciate and assist in the current challenges experienced by the industry.IntroductionWe need a mining sector that works. Mining employs over half a million people. It is the biggest earner of foreign exchange in our country. It also contributes about 20 billion rand directly to tax revenue. Mining also makes a far larger contribution as a buyer of goods and services, and a supplier of inputs to other sectors of our economy and other economies around the globe’ said President Jacob Zuma during the 2014 State of the Nation Address (Zuma, 2014). However, despite apparent commitment from government, enforced compliance with social and labour plans, regulations and Mining Charter targets, the South African mining industry is slow to gain local and international investor trust (Deloitte & Touche, 2013; Mashego, 2013).Industry players acknowledge that their context has changed – creating various challenges (Davis, 2014). In the past few years, such challenges included subdued commodity prices, increased working costs, constrained infrastructure, and high labour costs, coupled with poor levels of productivity, strained labour-management relations, an uncertain regulatory environment, and the inevitable maturation of the industry (Deloitte & Touche, 2013; Davenport, 2014). Mining affected communities also became more cognisant of their rights, and politicians more vocal in their expectations from their relationships with the mining giants (Davis, 2014). One of the main issues that contributed to the difficult operating conditions was claims from organized labour and Minister Shabangu that this industry is too slow to transform. Specific claims were made in terms of employment equity, fair salaries and wages for mineworkers, housing and living conditions, health and safety issues, and general working conditions (Limpitlaw et al., 2005; Miningmx, 2013; Shabangu, 2010). These claims were followed by what Gill Marcus, Reserve Bank Governor, explained as ‘unprotected strike action [that] has escalated into an uncontrolled, violent and unlawful landscape, led by a mob mentality in the absence of formal and recognised leaders’ (Mavuso,2013)."

Jan 1, 2015

By J. Mulenshi, J. Rosenkranz, P. Khavari, S. C. Chelgani

The geometallurgical concept has mainly been applied to primary ore deposits, starting from ore characterisation to the economic optimisation of the mining operation. However, as primary ore resources are becoming depleted and lower in grade, alternative sources need to be explored and a question of adaptability of the geometallurgical approach to the secondary resource repositories arises. The particle size distribution, chemical and mineralogical compositions of the Smaltjärnen historical tungsten tailings from physical separation in Yxsjöberg, Sweden were studied using drill core samples collected from different locations within the tailings repository in order to assess the amenability of the tailings to reprocessing. The tailings are dominated by the –600 to +149 μm particle size fraction. This fraction contains most of the elements of interest (W, Cu, S, Sn, Zn, Be, Bi and F) hosted by scheelite, chalcopyrite, pyrrhotite, cassiterite, danalite (both Zn and Be), bismuthinite and fluorite, respectively. The particle size distribution and mineralogical composition vary across the repository, suggesting a possible existence of geometallurgical domains, which require further assessment to evaluate metallurgical performance. Keywords: Historical tailings, tungsten, scheelite, geometallurgy, characterisation, mineralogy, reprocessing

Jan 1, 2020

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

By P. J. Kinver

This paper deals with the development of backfilling methods and systems at the Broken Hill orebody of Black Mountain Mineral Development Company (Pty) Limited, at Aggeneys in the north-western Cape Province. Production started in 1979, being confined to large diameter blasthole stoping methods in the upper, steeply dipping areas of the orebody. This blasthole reserve is now depleted and the production tonnage, 100000 tons per month, is produced from eight cut and fill stopes in the flatter dipping areas of the orebody. The fill methods of the blasthole stoping area evolved prior to the pillar extraction are briefly discussed together with the resulting experiences gained that enabled virtually 100% extraction to be achieved. The original cut and fill mining used costly hydraulic cemented fill; this was replaced partly by unconsolidated river sand and later by dune sand which occurs in abundance. The paper describes the planning, research work and commissioning of a cycloning plant that now enables dune sand to be used successfully as an unconsolidated hydraulic fill. The development of drainage, placement and control methods are also reviewed.

Jan 1, 1988

By M. Z. Emad, S. Raza, K. Jalil, M. A. Raza, M. U. Khan, S. A. Saki

Dimension stone mining is Increasing because of growing demand from the building and construction industries. Diamond wire saw cutting is a popular dimension stone mining technique around the world. Estimation of the production cost for this method is critical for these operations. n this research a production cost model was developed for the mining of granite using a diamond wire saw. Cost and production data were collected from a granitic dolerite operation in Pakistan for a 4.5-year period, and analysed to identify the cost components. Fuel (34%), labour (15%), consumables (40%), and maintenance (5%) were found to be the four major cost components in this operation. A regression-based dimension stone production cost model incorporating statistically significant variables was developed. The data presented a strong correlation of production cost with fuel, labour, and consumables costs. Finally, a production cost model based on the consumption cost of diamond wire is presented. The model was verified using actual production cost data, which indicated 95% (R2 = 0.95) variance in the data between the predicted and actual production cost values. The model may help field engineers in computing their dimension stone operational cost during the cutting phase.

Nov 6, 2023

By K. J. Craig, M. A. Swart, Q. G. Reynolds, L. Hockaday

A solar reflector soiling study was carried out at a ferromanganese smelter in South Africa to assess the soiling rates at different locations around the plant. Several meteorological parameters were monitored to give insight into the conditions that lead to increased soiling. Mineralogical characterization of dust samples collected from the reflectors and the atmosphere revealed that only a certain size fraction is of importance with regard to soiling, and that the dust can be attributed to both raw materials and smelter products. Proximity to the dust source was the primary driver for increased soiling. The site that experienced the most soiling was very close to raw material heaps; this was deemed an outlier and was excluded from the summary statistics. The secondary driver for increased soiling was location relative to the smelter dust sources and the wind’s direction and speed. The reflector set at the best location experienced 13.1% less soiling than the set at the ‘worst’ (but still feasible) location, represented by an averaged mean daily reflectance loss of 0.0186. The study revealed that while there are periods of intense soiling at this particular site, proper planning of reflector location in relation to the smelter dust sources can significantly mitigate the soiling rate.

Jun 5, 2023

By C. E. Dohm

The paper serves to show the importance of both a geological model and geostatistical model that support one another in mineral resource evaluation. It highlights the advantage of reference models for the geometry, the geological, statistical and geostatistical models of various orebody types and introduces a method for quantifying the combined uncertainty in these models. The example presented reveals how the above levels of information can be applied to add value to a resource evaluation process. It is a generic example in that it is the technique of combining uncertainty in the geological model (boundaries) as well as the grade model to assess the overall risk in the estimation of the resource. Data from the coal industry is used to illustrate the techniques. The geological uncertainty is considered via categorical simulations and these are combined with simulations of the variables (grades, thickness,) being estimated in the resource. The simulation techniques used are based on the application of GSLIB software1and a general discussion of the two simulation processes is included. In conclusion the paper demonstrates how the results of two types of conditional sequential simulation can be combined to produce confidence limits that take both uncertainties into consideration. This technique does not replace the resource estimation; it serves as an additional tool to quantify confidence in the resource evaluation model. The topics considered in this contribution are in terms of continuous improvement of mineral resource evaluation.

Jan 1, 2003

By P. V. Scheers

A rotating-cylinder electrode (RCE) was used to simulate the effect of flow velocity on pipe corrosion. A comparison is made between the electrochemical measurements obtained and those measured with a laboratory-scale flow loop. There is good general agreement if the speed of rotation of the RCE is adjusted to give the same value of mass transfer Coefficient as in the other system. Hence, it appears that the RCE is well suited to simulate actual flow conditions in pipes. The simultaneous effect of flow velocity and pH value on the corrosion rate of mild steel in a synthetic mine water was investigated. The i1nrease of corrosion rate was found to be more pronounced at lower pH values and, apart from a sharp increase below pH 4, the initial corrosion rate also increased at pH 7 and 6.

Jan 1, 1992

By B. S. Agbenuvor, R. Morrison, V. Jokovic, C. Antonio

Body breakage usually involves breakage of particles by compression between two surfaces or impacted against a rigid surface, with the latter of interest in this current study. This mode of breakage has been identified to be the most elementary size reduction process and the most effective breakage process in comminution devices. It has been found in the literature that the progenies produced from this form of breakage possess a residual velocity at which they move, after the breakage event. In the pursuit of efficiently utilising applied comminution energy, a laboratory-scale breakage device has been developed to deliver precise specific impact breakage using the concept of a fast-moving hammer and a slow-moving particle to effect breakage. The residual velocities of the progenies from the breakage event may be used to generate secondary breakage without further addition of energy if the particle encounters a stiff obstacle such as a steel plate at right angles to its path. To measure the extent of secondary breakage, the steel wall of the device was lined with a rubber material to suppress the second set of breakage events. The performance of the new device is analysed, based on calculated t10 values and measured residual velocities of the moving daughter particles. Testing involving anvils showed a much finer PSD and higher t10 compared to the test involving rubber lining. This finding is corroborated by the measured residual velocities of the progenies. The resulting energies calculated from the measured residual velocities of the progeny were found to be approximately 42-88% of the primary specific impact energy. This retained energy was found to be sufficient for secondary breakage. Keywords: Impact breakage, residual velocity, secondary breakage, energy utilisation

Jan 1, 2020

By S. Marx

More than twenty years ago Sasol, ISCOR, and some parastatals played a major role in ensuring that South Africa had sufficient technical skills. When the economy became tight and business and government were pressurized to decrease costs, the first budgets that were reduced were the training budgets. It seemed to be too expensive and too time-consuming to train apprentices. According to Stacey2, this is a major strategic issue facing the mining industry in South Africa. Two factors added to the shortage of skills challenge: ? Skills erosion and job losses ? Artisans ? currently the economy produces 5 000 but the need is 12 500 ? Level of mechanization in South Africa less than 10 per cent ? Average age of operators and artisans is 50 ? Greater awareness of occupational health effects of hand-held drilling. ? Workplace challenges ? The impact of HIV/AIDS and other employee wellness issues ? Changes and challenges in workplace environment i.e. the mining industry.

Jan 1, 2012

By R. Lechuti-Tlhalerwa

"Geometallurgy aims to improve mining project value by predicting the impact that ore and waste characteristics will have on mining and metallurgical processes. This requires integration of rich spatial models of orebody characteristics with validated process response models. These models have, until recently, been constrained by the spatial coverage and representativity of relevant data and the ability to validate predictions made.The revolution in the diversity and volume of data and computational power that is now becoming available for integrated geoscientific modelling of orebodies, and stochastic simulation of mining and mineral processes is accelerating. By embracing emergent integrated data analysis and simulation techniques, geoscientists and engineers can lead a transformation in the way the mining value chain, from orebody to recovery, can be conceived, evaluated, and operated by using the geometallurgical paradigm.This paper describes a methodology that is applied to an existing diamond operation. Analysis of spatial and process data is used to build an integrated geometallurgical value chain model (IGVCM). This IGVCM is used to generate geometallurgical options and evaluate their potential outcomes. The model facilitates the use of flexible, highly configurable, and potentially automated intelligent approaches to evaluate mining and mineral process configuration, and results in more robust design outcomes. The approach described here, and its successful implementation has potential to deliver step-changes in value. IntroductionGeometallurgy aims to identify treatability risks – and opportunities – that arise from the interaction of orebody characteristics with mining and treatment. Improved understanding of the rock/process relationships allows project planners and production teams to predict performance, identify potential shortfalls, and thus enable the proactive creation and evaluation of strategies to mitigate these risks. These advanced insights also create opportunities for continually improving operational performance through dynamically adapting and improving the process response to the changing properties of the ore (Figure 1)."

Apr 1, 2019

The February General Meeting of the Institute was held in Kelvin House, Johannesburg, on 19th February, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present forty-six Members, including Messrs H. E. Cross, A. R. C. Fowler, P. Lambooy, D. G. Maxwell, Dr J. T. McIntyre, Messrs J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), Messrs G. Abdinor, H. F. Allan, R. E. Barnes, M. M. Bayley, J. K. Boyd, R. R. M. Cousens, R. E. F. Cowley, D. Savile Davis, H. J. Davisson, C. T. Fenton, J. Fergusson, J. Fritz, M. L. Fitzgerald, J. M. Gosnell, J. C. Hall, S. A. Hancox, D. M. Jamieson, Dr D. G. Krige, Messrs J. E. V. Leeuwen, A. Louw, C. F. Louw, B. H. L. Leach, R. B. MacGillivray, C. S. McPhail, E. Margo, G. G. Nicolson, E. Pavitt, M. P. Pearse, F. O. Read, Dr M. D. G. Salamon, Dr H. S. Sichel, Messrs D. Storrar, S. G. Taussig, A. H. Taute, E. B. Viljoen and P. A. von Wielligh. Sixteen Associate Members, including Messrs S. T. Baron, W. M. Fitzpatrick, M. R. Fuller-Good, P. R. Garcia, H. G. Gericke, P. D. Hatfield, R. Hemp, G. S. Lee, Miss V. E. Marting, Messrs A. H. Munro, R. C. Power, O. F. Rheeder, G. C. Thompson and N. Zolezzi. Two Graduates, Messrs D. Bosley and J. C. Sutherland. Three Affiliates, Messrs R. K. Briggs, A. B. Cook and G. M. Thain. One Student, Mr P. W. Henrard. Twenty-three Visitors, including Messrs N. J. W. Bell, R. G. Bushell, A. Bryan, J. F. Cillie, C. M. de Beer, Dr F. H. Deist, Messrs D. S. Drake, P. G. du Plessis, R. W. Hodgson, D. M. Hawkins, S. C. H. Kearns, M. D. Labuschagne, L. Munro,R. Murchison and L. Robinson. Secretary, Mr D. C. Visser. Total present: Ninety-two. OBITUARIES The President: "It is my sad duty to announce the death of the following members of the Institute. Edward Frank Jud Bulman, Life Member, who joined the Institute in 1931 and passed away on 7th November, 1968. Elmar Fenton Chapin, Member, who joined the Institute in 1941 and passed away on 17th November, 1968. Solly Rabinowitz Rabson, Member, who joined the Institute in 1944 and passed away on 13th February, 1969. Mr. Rabson was the holder of two certificates of merit for papers presented to the Institute.

By DeVerle P. Harris, David E. Euresty

"Potential metal supply refers to metals to be produced from as yet unknown deposits. Naturally, to measure potential supply requires, among other things, inference to the number of deposits, their tonnage, and their grade Thus, probability distributions were constructed for each 400-square mile cell in Northern Sonora, Mexico. A computer system was developed that simulated the occurrence of deposits for each cell, exploration for the deposits, and their exploitation. Evaluation was performed for each deposit by discounted cash flow analysis.An objective of this study was to explore the effect of the transportation network and required road or railroad construction upon potential supply. Consequently, the evaluation system was designed to consider the spatial location of a simulated deposit to the existing transportation network and the market destination. The construction of linkages to connect the deposit to existing transportation arteries as well as the carrying of the concentrates to the intended market were simulated. in terms of cost. The selection of the path took into account the existing terrain. This was done by digitizing topographical maps and representing the topography of the area by an orthogonal grid of elevations. The optimum route was selected by dynamic programming, meeting a prescribed gradient constraint. The potential supply of each cell was determined, allowing for the infrastructure effect."

Jan 1, 2014

By J. Hadjigeorgiou, G. Knox

Since their introduction in 2010, paddled energy-absorbing rockbolts have been widely used in seismically active hard rock mines. This paper provides new data and reviews previous work to quantify the performance of paddled energy-absorbing rockbolts under controlled laboratory conditions. Of significance is the realization that the typical split location in impact tests, at the centre between two paddle anchor points can at best provide an upper limit value. This inherent variability in performance under different testing configurations should be acknowledged and taken into consideration in the design of ground support in seismic conditions. This paper discusses the reduction in capacity of paddled rockbolts as a function of loading angle from a maximum value during axial tests (0° loading angle) to the lowest value during pure shear (loading angle of 90°). A significant reduction in displacement capacity is observed as the loading angle changes between axial (0°) and 40°. Beyond a 40° loading angle up to shear (90°) loading the reduction in displacement capacity is less significant. Due to the variances in the capacity observed through the variance of the testing configuration: loading mechanism, direction of loading, location / presence of a discontinuity, it must be recognized that results from laboratory-based testing are not independent of the testing configuration. This should be acknowledged when extrapolating anticipated performance in the field.

Oct 9, 2024

By T. C. Huber

The southern African region has a high concentration of mineral resources and supplies much of the world?s platinum demand. As a result, the international community watches South Africa to understand the impact of supply on global markets. An analysis of supply certainty and risk plays a key role in the future of growing demand in various sectors. The southern African platinum industry experienced substantial growth in the early part of the 21st century, resulting in bullish forecasts for growth during the period of 2000?2006. However, southern African platinum producers saw a significant drop in production over the following three years as a result of many dynamic factors in operations and the global economy. Between 2006 and 2009 there was a million-ounce shortfall between forecast and actual production. This was raised as a concern at the Fourth International Platinum Conference in 2010 by Stephen Forrest during his keynote address, specifically regarding the lack of understanding in the market of the causes of this shortfall and any action that was being taken to address them. This paper reviews publicly available information in the media and corporate reports and communications for the period January 2006 to December 2009. In addition, several interviews were held with key stakeholders in the industry to provide further perspective. The paper then highlights the main reasons that are reported to have affected the loss in production over the period and discusses the possible implications of the information that the mining industry does and does not disclose regarding platinum supply.

Jan 1, 2012

Exxaro installed their first ultra fines treatment plant at Leeuwpan Coal mine. The plant is now fully operational and results already show that the plant has great potential. The plant was designed and installed by DRA. Several challenges were faced during the installation due to the space constraints in the Leeuwpan plant. Efficiency tests were conducted on both modules after commissioning and showed very promising results. A lower ash product with a higher yield can be produced with the fine coal dense medium cyclones compared to the spirals previously employed.

Jan 1, 2010

Geological mapping makes an important contribution to orebody knowledge during the evaluation of structurally controlled gold veins. Orebody knowledge comprises an understanding of mineralization characteristics relevant to evaluation, mining, processing and environmental issues and allows project expectations to be realistically set. Structural interpretation to define continuity and mineralization controls is a key part of geological risk reduction and the reporting mineral resources using the JORC and other codes. The Dolgellau gold belt is a small British field that produced an estimated 150 000 oz from narrow quartz veins. Historical records, recent exploration and production data, published material, and accessible surface and underground exposure provide a valuable case study. Previous mapping has shown the general geometry of vein systems, but tends to accentuate gross geological continuity. Recent work has attempted to determine internal vein architecture and examine the significance of the historical views of ore shoot controls. The work resulted in the definition of vein continuity scenarios for the gold belt and evaluation expectations associated with each. This has, in turn, led to a realistic view of what can be achieved from an evaluation and project development perspective.

Jan 1, 2009

By S. Fazluddin, K. C. Sole, M. R. Serwale, T. Coetsee

The CSIR-Ti process employs lithiothermic reduction of titanium tetrachloride feedstock to produce titanium sponge. The product is therefore contaminated by a range of lithium and chloride species. In this study we examine the effects of particle size, temperature, and HCl concentration as input leaching variables on the removal of chlorides from the crude titanium sponge. A review of the aqueous chloride chemistry of Li and Ti provided initial conditions for leaching of impurity species from the sponge. Experimental results confirm that the effectiveness of leaching and removal of dissolved impurities from the sponge are dependent on leaching kinetics, which are influenced by temperature, particle size, and morphology. Of the variables tested, reaction temperature had the strongest influence on the oxygen content of the leached product. The HCl lixiviant concentration had a negligible effect under the conditions tested. Leaching of crude titanium sponge (−10 mm size fraction after crushing) at 14°C in either 1 M or 0.032 M HCl yielded a titanium sponge product that met the ASTM standard specification for commercially pure Grade 1 titanium, i.e., oxygen content < 0.18 mass% and chloride content < 0.15 mass%.

Dec 13, 2022