Search Documents

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

By G. S. Harper

Noise in general and drilling noise in particular have received increasing attention within the South African mining industry during the last 10?15 years. The Mine Health and Safety Committee1, during their 2003 annual summit, established two significant milestones to be met by December 2008 and December 2013. The 2008 milestone target is that of no more than ten per cent deterioration in hearing among occupationally exposed individuals, whereas the 2013 milestone target is that of less than 110 dB sound pressure levels at any place in the workplace. While these targets relate to general noise within the mining industry, it is widely believed that the most significant source of noise contributing to noise induced hearing loss (NIHL) among the underground workforce, is that of pneumatic rock drills. Data pertaining to the noise emission level of any machine is generally reported as either a sound pressure level or a sound power level of a single machine measured under free field conditions as defined in Appendix 3 of SABS-ISO 37442. However, rock drills are seldom used in isolation and underground conditions cannot be considered as free field. A methodology for the selection of rock drills on the basis of total operating cost has been developed. However, this paper focuses on the noise elements of the generic methodology and provides a model for the prediction of the composite sound pressure level and the equivalent noise exposure levels of groups of individuals from machines, used singly and in combination in an underground environment based on the sound pressure level determined according to SABS-ISO 3744 under free field conditions. The methodology includes provision for the consideration of the effect of hearing protection devices and the use of multiple machines in combination and provides an indication of the potential costs of hearing compensation.

Jan 1, 2006

By W. Barthel, B. A. Dippenaar, J. Malan

In its most basic form, the process of sintering is very simple, and has been in use since the turn of the previous century. However, while the basic process is simple, control of the process relies on a number of extremely complex interdependent process parameters and requires a thorough understanding of the effect of these parameters on production capacity and product quality. Further, as with many other processes, the process parameters and hence design details of visually similar installations are highly dependant on the specific feed materials. While the industry trend has been towards an increase of capacity in order to lower unit production cost, typically in Iron ore sintering plants, this approach is not always possible for other commodities because of the scale of operation. This paper seeks firstly to describe some design considerations of sinter plants; secondly, to report on results from testwork performed with a specific series Manganese ore blends; and last, to relate these results to the design of new small-scale Manganese ore sinter plants.

Jan 1, 2004

By M. Tanaka, K. Aoki, T. Mori, H. Morioka, K. Iwano, T. Kanagawa

To estimate the detailed characteristics of the rock around the cavern during excavation, new monitoring technique for dynamic properties of the rock has been applied. In this paper, micro-seismic monitoring and AE monitoring technique are applied to the excavation of large underground rock cavern and the result was discussed to clarify the acutal behavior of EDZ around the cavern. Zur Einschätzung der Gesteinseigenschaften um die Ausschachtung herum haben die Autoren eine Technik eingesetzt, mit der die physikalischen und dynamischen Änderungen im Gestein um den Schacht während der Ausschachtung beobachtet werden. In der vorliegenden Studie wurde zur mikroseismischen Überwachung ein AE Überwachungsverfahren eingesetzt und die Autoren berichten über die Veränderungen in den Gesteinseigenschaften um die Ausschachtung herum. Dans le but d'évaluer en détail les propriétés des roches qui forment les parois des cavernes creusées, les auteurs ont utilisé une technique de mesure permettant d’observer les modifications physico-dynamiques des roches aux alentours de la caverne pendant son excavation. Dans le cadre de cet article, une technique de surveillance de l’agitation et du bruit microséismiques a été mise en œuvre et les auteurs font état de la modification des propriétés de la roche environnante.

Jan 1, 2003

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2009

By R. M. Goktan

Point-attack picks are one of the most widely used tools for the mechanical excavation of rock and coal. In the literature, some practical formulas have been developed to estimate their performances under varying cutting conditions such as the pick geometry, cutting depth and cutting geometry. In this study, it is shown that Evans?s theoretical model, the most cited in the literature, has serious limitations concerning the changes in the cutting geometry. Analysis of the two independent full-scale linear rock cutting experimental data reveals that both his theory and its recent modification can not fully explain the mechanism of rock breakage under asymmetrical attack. The cutting force predictions made by employing such models are shown to be too significantly weak to be of any service in practice. In this study, a semi-empirical approach was followed by means of which cutting forces under varying cutting geometries could be made. By analysing the full-scale rock cutting test data, prediction equations of the peak cutting force and mean cutting force have been developed. Comparisons of laboratory determined and predicted force values indicate that the suggested prediction equations are applicable to quite different rock materialsm which have uniaxial compressive strength in the range of about 30?170MPa, and valid for different cutting geometries. It is also shown by regression analysis that the established prediction equations are statistically significant.

Jan 1, 2005

By F. Cihangir, A. Kesimal, K. Karaman, B. Ercikdi

Uniaxial compressive strength (UCS) and shear strength parameters(cohesion and angle of internal friction, Cand F) of rocks are important parameters needed for various engineering projects such as tunnelling and slope stability. However, direct determination of these parameters is difficult and requires high-quality core samples for tests. Therefore, this study aimed to explore the applicability of the Brazilian test (BT) - a simple, less sophisticated and inexpensive method for both specimen preparation and testing - to estimate the UCS and shear strength parameters of rocks. Thirty-seven rock types were sampled and tested, 24of which were volcanic, 8 were metamorphic, and 5 were sedimentary. Statistical equations were derived to estimate the UCS and shear strength parameters of rocks using the BT. The validity of the statistically derived equations was confirmed using predictive analytics software (PASW Statistics 18). A strong linear relation was found between BT and UCS values. BT and UCS values exhibited prominent linear correlations withthe cohesion values of rocks. The Mohr envelope was also used to determine the cohesion and friction angle of rocks using BT and UCS values. It is deduced from the current study that the BT values can be used to estimate the UCS and cohesion. However, no relation was observed between the angle of internal friction values and the UCS and BT for all rock types. Therefore, different approaches are suggested for the estimation of the internal angle of friction for application in the preliminary design of projects.

Jan 1, 2015

By D. Yu. Paleev, O. Yu. Lukashov, A. Yu. Krainov, E. R. Shrager, I. M. Vasenin

The gas-dynamic method is presented of calculation of explosion-proof distances during an explosion of the methane-air mixture in mine working. On the basis of this method is modelled of shock waves interaction with explosion protective parachute partitions, obstructions and water barriers. Calculations have been carried out of attenuation factors of shock waves during their interaction with explosion protective structures, arranged near conjugation zones of mine workings. Possibilities have been analysed of suppression of intensity of shock waves and of propagation of shock waves control in mine working network of coal mines by installation of explosion protective structures.

Jan 1, 2003

By Cade Mweemba, Alex Mwanza, Jackson Sikamo

"The Zambian Copper mining industry as we know it today has its genesis from early in the 20th century in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production going from zero to a peak of 769 000 tons of copper in 1969. At the same time, the industry created jobs to the extent that in 1972 the industry had over 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level at the dawn of the 21st century in the year 2000 when production was 250 000 tons. In terms of jobs, an average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000. Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and investments of over USD 12 billion, the industry production levels increased year- on-year to reach a peak of 763 000 tons in 2013 with direct jobs reaching 90 000. This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support to other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies and human capital. This is looked at particularly in the light of current challenges the industry is facing and makes suggestions on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2015

By D. F. Malan, T. E. Oates

A recent experimental pillar extraction project at a UG2 bord-and-pillar mine presented a unique opportunity to compile a new pillar database. Currently, the South African hard rock bordand- pillar mines are designed using the Hedley and Grant formula with a modified K-value. This empirically derived formula was developed for uranium mines in the Elliot Lake district of Canada. The use of this formula for the design of pillars in South Africa is questionable. Very few pillar failures have nevertheless been observed and its current calibrations for the various reef types are possibly too conservative. A new UG2 pillar database of 66 pillars, of which seven are classified as failed, was compiled by the authors. This enabled a revised ‘first-order’ calibration of the K-value for the Hedley and Grant formula. The new estimated value for the UG2 is K = 75 MPa. This gives a pillar strength that is more conservative than the PlatMine formula. This work should nevertheless be considered as only a preliminary calibration as the database was small. Further work is also required to determine whether the exponents in the formula for the width and height parameters are appropriate for UG2 pillars.

May 3, 2023

By E. Laine

Rock density determinations are necessary for ore resource evaluations from estimated block grades in g/t. Rock density depends on the mineral composition and, thus, it is specific for each rock type. The rock density distributions for different rock types are often symmetric. Hence, the arithmetic mean is a good approximation for the average density for lithological units. However, there may exist spatial variation in density values due to alteration, fracturing and original heterogeneities such as layering. This study compares the kriged density model with the one with constant density values for different lithological units in the evaluation of metal amounts in rock blocks. The case study consisted of rock densities measured from the drill cores at Ahmavaara PGE deposit in northern Finland. The used Ni contents were simulated in accordance with the spatial distribution of rock densities. The Ni amounts in 2x2x2 m3blocks are higher for the kriged densities than for the average densities. The difference is increasing with the increasing metal amounts due to the nonlinear correlation between Ni content and rock density. The final effect on the resource estimation depends on the cutt off grade and prices of the metal, for example, for a very valuable metal the small differences are significant

Jan 1, 2003

By M. M. Makhofane

Anhydrous zirconium tetrafluoride can be used as a precursor for the manufacturing of nuclear-grade zirconium metal. This can be done by fluorinating plasma-dissociated zircon with ammonium bifluoride in a batch reactor. This paper describes the batch process. It was proved that anhydrous zirconium tetrafluoride can be manufactured by this route as confirmed by X-ray diffraction. The process shows potential for scaling up to the kilogram scale and possibly the tonnage scale.

Jan 1, 2012

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

By M. Abdellatif

The Mintek Thermal Magnesium Process (MTMP) process is based on DC open arc metallothermic smelting of calcined dolomite at normal pressure and temperatures of 1650?1750°C. The process was demonstrated at the pilot scale in the period 2000?2004. Major changes to the MTMP pilot plant were made throughout the development period, which lasted for about five years. The changes included design and installation of new equipment, modification of existing equipment, changes in the metallurgical approach in terms of feed rates, feed recipes, furnace operating temperatures, cold and hot dolime feeding, and steady and systematic changes in the operating procedures and maintenance of the plant. As a result, the performance of the pilot plant gradually improved from one campaign to the next, in terms of availability and in particular the condensation efficiency. In Run 10, the process was successfully demonstrated over an 8-day campaign. Keywords Magnesium, condensation efficiency, DC arc furnace, silicothermic reduction.

Jan 1, 2011

By A. V. Aleksandrov, T. N. Aleksandrova, N. V. Nikolaeva

Using complex thermal analysis methods, flotation concentrates were classified depending on what the organic and nonorganic carbon form is. The possibility of ultrafine particles of valuable components (noble metals and diamonds) extraction using physical actions of different genesis in the processing of ‘unconventional’ mineral raw materials is considered in the paper. Electromagnetic treatment is one of new technologies in the field of mineral processing. The features of the electromagnetic effect on substances include uniform heating throughout of the volume, high speed and low inertia of heating, as well as the possibility of selective heating. A selection of studies including gravity, flotation and extraction methods of enrichment using energy effects, as well as thermal analysis was conducted to establish the availability and possibility of extracting valuable components. Due to microwave and high-temperature exposure, minerals and gas-liquid inclusions are decremented, and crystal-chemical water is released, resulting in additional defects. As a result, self-cleaning of sulphide minerals from atoms of scattered gold occurs by distilling it into peripheral parts of grains and intergranular space, where ultradispersed individuals are formed. Keywords: Refractory gold-bearing ores, physico-chemical properties, ore preparation, flotation, modelling, simulation, selection

Jan 1, 2020

Significant advances have been made in the design of centrifugal slurry pumps that are used for pumping high-density viscous and paste slurries. This paper presents the results of a series of centrifugal pump performance tests that were conducted using an FLSmidth 6 x 4 Krebs millMAX centrifugal pump. The pump was fitted with a dry mechanical seal to prevent dilution of the slurry from gland service water, as the theology of the slurry is sensitive to small changes in slurry density. Tests were done using paste kaolin slurry with Bingham yield stress values between 578-1 120 Pa and plastic viscosities between 728 and 1491 mPa.s. The viscous properties of the paste during each pump test were measured using a rotational viscometer. Pump head and efficiency de-rating were measured and compared to the correlations of Walker and Goulas (1984). The test data shows the pump's best-efficiency point (BEP) changes and shifts to the left of the performance curve. The pump efficiency decreases as the slurry yield stress increases. The head de-rating data shows more head de-rating at the low flow rates compared to the high flow rates for the high viscosity slurry, which is in line with the findings of Walker and Goulas (1984). This paper demonstrates that it is possible to pump very viscous, high yield stress slurries with limited head and efficiency de-rating using centrifugal pumps, provided that positive suction conditions are maintained at all times.

Jan 1, 2012

By M. S. Raseroka

An experimental rig has been constructed to produce chloride stress corrosion cracks in Type 304L stainless steel tube samples. The samples are to be used to test possible in situ repair methods in future work. The factor which influences the time to failure most strongly is the sample temperature; the distribution of cracks within the sample is affected by local temperature variations and by the position of the water line. Low-frequency oscillations in stress, caused by the on-off temperature controller, did not appear to influence cracking in these tests.

Jan 1, 2009

By J. M. McKinley

Mineral exploration programmes around the world use data from remote sensing, geophysics, and direct sampling. On a regional scale, the combination of airborne geophysics and ground-based geochemical sampling can aid geological mapping and mineral exploration. Since airborne geophysical and traditional soil-sampling data are generated at different spatial resolutions, they are not immediately comparable due to their different sampling density. Several geostatistical techniques, including indicator cokriging and collocated cokriging, can be used to integrate different types of data into a geostatistical model. However, with increasing numbers of variables the inference of the crosscovariance model required for cokriging can be demanding in terms of effort and computational time. In this paper a Gaussian-based Bayesian updating approach is applied to integrate airborne radiometric data and ground-sampled geochemical soil data to maximize information generated from the soil survey, enabling more accurate geological interpretation for the exploration and development of natural resources. The Bayesian updating technique decomposes the collocated estimate into two models: prior and likelihood models. The prior model is built from primary information and the likelihood model is built from secondary information. The prior model is then updated with the likelihood model to build the final model. The approach allows multiple secondary variables to be simultaneously integrated into the mapping of the primary variable. The Bayesian updating approach is demonstrated using a case study from Northern Ireland. The geostatistical technique was used to improve the resolution of soil geochemistry, at a density of one sample per 2 km2, by integrating more closely measured airborne geophysical data from the GSNI Tellus Survey, measured over a footprint of 65 x 200 m. The directly measured geochemistry data were considered as primary data and the airborne radiometric data were used as secondary data. The approach produced more detailed updated maps and in particular enhanced information on the mapped distributions of zinc, copper, and lead. The enhanced delineation of an elongated northwest/southeast trending zone in the updated maps strengthened the potential for discovering stratabound base metal deposits..

Jan 1, 2014

By L. K. Witika, J. H. Masinja

"Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. Of the six frothers tested, two came from the alcohol family, two from the glycol family and last two were formulated products. The initial work involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. For froth stability tests, six frothers were tested on a two-phase (water–air) system using the Bikerman column flotation cell, while water recovery tests were conducted using a total of seven frothers, including the standards for each plant. The results of the testwork showed that (i) although a stable froth is essential for optimum recovery of valuable minerals, a higher molecular weight frother, like Dowfroth 250, caused poor selectivity when used on fine ores and (ii) a lower molecular weight frother was suited for Lumwana ore, while a mid to higher molecular weight formulated product was suitable for Kansanshi sulphide ore. INTRODUCTION Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. The initial work of this project involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. In order to investigate the gangue entrainment levels in the Lumwana and Kansanshi sulphide ores, two well-known methods (froth stability and water recovery) were used. Firstly, froth stability tests were conducted using six frothers, two from the glycol family (Dowfroth 200 and Dowfroth 250), two from alcohol family (MIBC and pine oil) and other two from the formulated family (Betafroth 20 and Betafroth 245), at the University of Cape Town’s Centre for Mineral Research (CMR) laboratories. Froth formation and stability measurements were conducted using the Bikerman column flotation cell."

Jan 1, 2015

By E. Demir

Transportation cost is the dominant cost and accounts for almost half of the total mining cost in surface mining. Therefore, determining transportation cost is critically important for the economic feasibility of mining projects. Turkey produces around 85 million tons of lignite per annum. The biggest state-owned company, Turkish Coal Enterprises (TKI), accounts for 43 per cent of the country?s total lignite production. Around 85 per cent of the produced lignite is used in power plants for electricity generation and 15 per cent is used for domestic heating in cities and urban areas. On behalf of the Turkish government, TKI distributes around 2 Mt of lignite annually, at no cost to poor needy families countrywide in accordance with Social Assistance and Solidarity Funding aid. Subcontractors are utilized for lignite transportation, and conflicts arise due to the different transportation cost calculations at different mines. A robust model that provides unbiased cost estimations is therefore of paramount importance. This paper presents the transportation cost estimation software, NAKMAL, that has been developed for estimating the transportation cost of lignite from the mine face, including excavation and loading, to various final destination points through five different transportation scenarios. NAKMAL was designed using VisualStudio.NET, validated using field data and some case studies, and it is currently being used by TKI for calculation of transportation cost country-wide.

Jan 1, 2012