Search Documents

By L. Bam, R. Machaka, S. Chikosha, N. S. Muchavi

"Parts manufactured through power metallurgy (PM) typically contain pores that can be detrimental to the final mechanical properties. This paper explores the merits of 3D X-ray computed tomography over traditional microscopy for the characterization of the evolution of porosity in metal injection moulding (MIM) and direct powder rolling (DPR) products. 17-4 PH stainless steel (as-moulded, as-debound and sintered) dog-bone samples produced via MIM and Ti-HDH strips (as-rolled and sintered) produced via DPR and were analysed for porosity. 3D microfocus X-ray tomography (XCT) analysis on specimens from both processes revealed spatial variations in densities and the existence of characteristic moulding and roll compaction defects in agreement with traditional microscopic microstructural analysis. It was concluded that micro-focus XCT scanning can be used to study MIM and DPR parts for the characterization of the amount, position and distribution of porosity and other defects. However, the majority of the sub-micron sized pores could not be clearly resolved even at the highest possible instrument resolution. Higher-resolution scans such as nano-focus XCT could be utilized in order to fully study the porosity in MIM and DPR parts. IntroductionMetal injection moulding (MIM) is a novel process, which combines the advantages of powder metallurgy (PM) and plastic injection moulding. MIM has found widespread applications in the cost-effective production of high-sintered density small parts with complicated shapes and mechanical properties equivalent to those of wrought materials (German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013). There are four basic processing steps involved in MIM, namely; feedstock preparation, injection moulding, debinding and sintering. These steps are discussed in greater detail elsewhere (Machaka, Seerane and Chikwanda, 2014; German and Bose, 1977; Machaka and Chikwanda, 2015; German, 2013).Feedstock preparation involves mixing metal powder with a carefully selected composition of polymeric binder materials at a specific temperature. The feedstock is then granulated and injected into a predefined mould die with the desired shape. The part produced during the moulding step is referred to as a ‘green’ component. The green component typically contains no porosity since the spaces between adjacent powder particles are readily filled with the binder materials (German and Bose, 1977; Li, Li and Khalil, 2007). Debinding is the systemic removal of the binder components by chemical, catalytic, or/and thermal means while maintaining the shape of the component. The part produced after the debinding step is referred to as a ‘brown’ component. Debinding is known to be the source of porosity in brown components (Ji et al., 2001; Tsai and Cen, 1995). Finally, the brown debound part is sintered to full or nearfull density (Sotomayor, Varez and Levenfeld, 2010). The sintering step and associated densification closes up the majority of the pores. Sintered MIM parts are typically sintered to high density (95–99%) and retain an irreducible amount of residual porosity (Barriere, Liu and Gelin, 2003; German, 1990)."

Jan 1, 2016

By H. S. Sichel

This study deals with the development of some new theory concerning the bias which will result from the employment of the t-estimator if in fact the underlying distribution of ore values is not lognormal. It is found that the t-estimator is robust as long as the logarithmic variance is small and the shape factors of the transformed distribution are not unduly large. The choice of the threshold parameter [t] for the t-estimator is important, and some hints are given how to estimate it if the sample size is small, as en- countered in borehole valuation problems.

Jan 1, 1987

By J. McPherson

In order to add value to South Africa?s gold reserves AuTEK, a joint venture between Mintek and Anglogold-Ashanti, was started in 2000 with the aim of developing new industrial uses for gold. Accordingly gold catalysts are being made in kilogram quantities by Project AuTEK and sold toend users and other interested parties under the trade name AUROliteTM. Although these materials are optimized for use in CO oxidation applications, demonstration of appropriate activity, selectivity and durability in both liquid- and other gas-phase reactions has been shown1. The review below highlights the recent use of these materials, and other gold catalysts, in reactions of commercial interest.

Jan 1, 2009

By H. Rosen

The pump is the heart of most industrial and mining plants, providing the energy to separate valuable minerals from process feed. The actual effect of the pump, both in terms of production costs and overall process efficiency, is often assumed or misunderstood by engineers due to insufficient pump performance data. Pump performance can be understood and corrected, where required, through continuous performance monitoring, leading to dramatic improvements in both pump life cycle costs and system efficiencies. The performance of every pumping application is subject to variation and the main contributing factors are as follows: ?Unavoidable deviations from pump supplier curves ?Pump wear ?Pump curve derating factors for slurry pumping ?System curve variation ?Deviation from basic principles of centrifugal pump operation. These are discussed in detail through case studies and the author?s personal experiences. This paper shows ways to minimize the effect of these variations, thereby reducing performance loss and preventing damage to the pump. The paper discusses the benefits of efficient pump operation, the requirements of pump performance monitoring, and its practical application to pump operation in the slurry and water environments. The cost of remedial actions is explored and compared against the savings in both power and plant reliability, resulting in a reduced life cycle cost of the pump.

Jan 1, 2010

By L. Shoke

The aim of this study was to develop an in-house tensile testing procedure that would yield accurate and reproducible parameters as input material properties into computational models for numerical simulations of the mechanical behaviour of TM380 mild steel. To achieve this objective, we reviewed the ISO 6892:2009 tensile testing standard along with reported good practice guidelines. Tensile tests were conducted on a dog-bone shaped TM380 mild steel specimen with strain gauges attached on either side, to monitor alignment and measure strain, using three different types of tensile testing machines. Parameters quantified included yield stress, ultimate tensile strength, and modulus of elasticity. The values of these parameters were found to be in agreement with the values supplied by the manufacturer's specification and showed minimal variations between laboratories. Thus it can be concluded that the tensile test procedure used resulted in accurate and reproducible results. The strain values calculated as per standard were in disagreement with those determined from extensometer and strain gauges and resulted in lower elastic modulus values. This confirms that the current testing procedures require the use of long-range strain gauges or extensometer to determine the strain. A chemical analysis was conducted to verify the specification by the manufacturer. The specimen was found to be fairly homogeneous with minor sulphide inclusions. The micrographs reveal a pearlite and ferrite structure typical of mild steel, and the fractographs show a dimpled surface typical of ductile fracture, which is an attribute of mild steel.

Jan 1, 2013

By J. Gholamnejad

Determination of the optimum production schedules over the life of a mine is a critical mechanism in open pit mine planning procedures. Long-term production scheduling is used to maximize the net present value of the project under technical, financial, and environmental constraints. Mathematical programming models are well suited for optimizing long-term production schedules of open pit mines. There are two approaches to solving long-term production problems: deterministic- and uncertainty- based approaches. Deterministic-based models are unable to deal with grade and geological uncertainties, which are two important sources of risk in mining industries. This may lead to discrepancies between actual production obtained by these algorithms and planning expectations. In this paper, a new binary integer programming model was developed for long-term production scheduling that incorporates geological uncertainty within the orebody. Then, traditional and uncertainty-based models are applied to an iron ore deposit. Results showed that the uncertainty-based approach yields more practical schedules than traditional approaches in terms of production targets.

Jan 1, 2012

By H. J. Le Roux, W. B. Drummond

1. INTRODUCTION We have a moral responsibility towards the world to reduce the harmful deposits we emit into the environment arising from beneficiation technologies. Industry has not willingly spent money to limit these emissions because it affected their profit margin with the end result of emitting harmful elements into the environment. Governments have thus rightly stepped in and enforced systematic reduction of these emissions through legislation. In the past beneficiation of sulphur bearing ores was typically done through hydro-metallurgical concentration, smelting, followed by Sulphur removal by converting processes like the Pierce Smith converter. The latter two processes emitted substantial quantities of Sulphur into the atmosphere. Spiralling costs and legislation have resulted in the quest to develop more efficient and environmentally friendly processes to achieve the same end results. New hydro-metallurgical processes like the ActiVox process has completely eliminated the pyro-metallurgical processes. Kansanshi are also operating a similar process. It however elicits other ground water and spillage pollution hazards and problems of it?s own. Various improvements has also been made to the pyro-metallurgical stages, examples being combined smelting and converting with the Noranda reactor, the Codelco CMT furnace, one step flash smelting/converting or the Mitsubishi continuous smelting, converting and slag cleaning process. The new converting processes are also normally enhanced using oxygen leading to higher SO2 gas strength with only a marginal increase in off-gas volume. These processes have led to better efficiencies and a more controlled environment that reduces pollution, but does not eliminate it completely. The fact that there are still more than 70 existing Pierce Smith converter plants throughout the world that needs to be replaced or upgraded at tremendous capital cost, means that we will have the environmental problems for some time to come. The need thus exists to cost effectively get these existing plants into a state where they meet the new environmental regulations, community and safety requirements. This paper will concentrate on just one aspect of this quest, i.e. reduction/removal of off-gasses emanating from the converting of non ferrous sulphur mattes to achieve higher or specialised grades of refined metals.

Jan 1, 2005

By C. Massola, E. E. M. N. de Guzmán, M. G. Bergermana

The abrasiveness of a mineral or rock is an extremely important topic in the mining industry and is generally measured by the Bond abrasion index (AI). However, to determine such an index by the Bond test requires 1,600 g of sample with particle sizes ranging from ½” to ¾”, which are not available in certain situations, such as ore prospecting, drilling, and geometallurgical studies. In order to investigate the abrasiveness of smaller-sized sample materials, a modified LCPC test was developed, which allows testing fine materials (i.e., 1.0 mm or smaller) to predict wear in ore processing circuits and anticipate possible failures resulting from changes in abrasive characteristics of the ore being processed. The results for 16 different materials indicated a good correlation with the AI and the modified LCPC, resulting in a reliable alternative for the AI. Keywords: Bond Abrasion Index (AI), LCPC, abrasiveness

Jan 1, 2020

1. Book reviews Quantitative texture analysis, edited by H. ,}. Bunge and C. Esling. Deutsche Gesellschaft fur Metallkunde, 1982. 551 pp. Reviewer: L. 1\'1.Matthews Boundary element methods in solid mechanics by S. L. Crouch and A. M. Starfield. Reviewer: J. A. C. Diering World mineral statistics 1976-1980. Produdion,' exports,' imports, by Institute of Geological Sciences. London, Her Majesty's Stationery Office, 1983. £18.00 Reviewer: R. P. King 2. New publications Canadian mines,. perspective from 1982. Mineral Bulletin MR 197. Supply and Services Canada, Hull, Quebec K1A 059, Canada. Copper' s changing cost structure, by Commodities Research Unit Ltd (31 Mount Pleasant, London, WClX OAD, England). Petrology of metamorphic rocks, by M. Suk. New York, Elsevier, 1983. 320 pp. U.S. $68.00. Applied geomorphology, by H. Th. Verstappen. New York, Elsevier, 1983.442 pp. U.S.$95.75. Tin and its uses, no. 137, by the International Tin Research Institute. Greenford, the Institute (Fraser Road, Greenford, Middlesex UB6 7AQ, England), 1983. 3. New journals Mining Science and Technology, edited by C. 0, Brawner and B. N. Whittaker, is to be published quarterly in one volume per year by Elsevier. Aluminium, published monthly by Aluminium -Verlag GmbH, P.O. Box 1207, D-4oo0 Diisseldorf 1, F.R. Germany. DM 690.00 per annum. Rock mechanics The South African Institute of Mining and Metallurgy is to hold two schools on 'Rock Mechanics in Mine Management' at the University of the Witwatersrand, Johannesburg, from 23rd to 27th January, 1984, and from 30th January to 3rd February, 1984. The Federation of Societies of Professional Engineers The Federation of Societies of Professional Engineers (FSPE) has been a member of the World Federation of Engineering Organisations (W FEO) for many years and has regularly sent delegates to the biennial conference of that organisation. Second progress report by ASRET The Professional Engineers Joint Council was estabislhed in 1960 and initially its main fWlction was to represent the interests of engineers. Explosives technology The Center for Explosives Technology Research (CETR) has been established at the New Mexico Institute of Mining and Technology (Tech) in Socorro, New Mexico. International Tunnelling Association A conference entitled 'Ita Tunnels 1984' will be held in Caracas, Venezuela, from 2nd to 7th June, 1984. Automation The IFAC Symposium on Automation for Mineral Resource Development is to he held in Brisbane (Australia) from 9th to nth July, 1985.

Jan 1, 1983

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.

Jan 1, 2003

By S. Khoshjavan

In this investigation, the effects of different coal chemical properties were studied to estimate the coal Hardgrove Grindability Index (HGI) values index. An artificial neural network (ANN) method for 300 data-sets was used for evaluating the HGI values. Ten input parameters were used, and the outputs of the models were compared in order to select the best model for this study. A threelayer ANN was found to be optimum with architecture of five neurons in each of the first and second hidden layers, and one neuron in the output layer. The correlation coefficients (R2) for the training and test data were 0.962 and 0.82 respectively. Sensitivity analysis showed that volatile material, carbon, hydrogen, Btu, nitrogen, and fixed carbon (all on a dry basis) have the greatest effect on HGI, and moisture, oxygen (dry), ash (dry), and total sulphur (dry) the least effect. Keywords coal chemical properties, Hardgrove Grindability Index, artificial neural network, back-propagation neural network.

Jun 1, 2013

By D. H. Batchelor

Efficient modern-day mining operations are turning increasingly to technology to combat rising operating costs in an adverse economic climate for the industry. Computerised truck dispatching is one such technological advance that has enhanced the efficiency of the mining operation at Palabora. The economic incentives, basic operation and general system benefits of Palabora's computerised truck dispatching system are considered.

Jan 1, 1987

By C. K. Chabedi

"This paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield. The resources occur at a depth greater than 250 m and the thickness of the coal is roughly 110 m, but the top 50 m comprises coal intercalated with shale and the bottom 60 m contains five seams with sandstone and shale partings. Various factors affecting multiple seam mining at these great depths are discussed with reference to lessons learned from local and international experience on multi-seam mining. Field geological and geotechnical data was utilized to assess the stability of the roof of the seams. There is no specific rock mass rating for the Waterberg area, therefore approximate coal mine roof rating (CMRR) values were used to propose appropriate support strategies. Analysis of Multiple Seam Stability (AMSS) was used to analyse the strength of the parting or interburden between the various seams, the mining sequence, and the interaction between the various seams.The research indicated that it is possible to mine seams with a low CMRR at high mining rates using longwall mining, although support for gateroads is expected to be expensive, time-consuming and onerous to install, and will impact gateroad development rates. It will not be possible to simultaneously mine zones in close proximity and failure of the interburden is predicted, thus dangerous mining conditions are anticipated. However, it will be possible to mine just two of the eleven zones using longwall mining. IntroductionThis paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield using bord and pillar and longwall mining. Figure 1 illustrates the location of the Waterberg coalfield relative to other coalfields in South Africa, while Figure 2 shows the areas containing deep and shallow resources. The Waterberg resources are expected to contribute to South Africa’s future energy requirements, and are currently exploited at the Grootegeluk open pit mine. Grootegeluk produces coal mainly for a power station, with the higher quality product supplied as metallurgical coal. The deposit is technically unique and challenging, being a multi-seam coal deposit with a total of 12 seams over a thickness of 110 m as shown in Figure 3, including Zone 5. There is currently limited knowledge on the multi-seam mining of the deep Waterberg resources. Multi-seam mining utilizing the bord and pillar method has been practised in South Africa before, but at a depth of less than 100 m in the Witbank coalfields. Multi-seam mining in thin seams has also been performed in the Natal coalfields at a depth of less than 160 m, but mostly using bord and pillar mining and secondary mining (partial pillar extraction)."

Jan 1, 2016

By R. C. W. Webber-Youngman

The mining industry in South Africa faces real challenges with regard to the reduction of safety-related incidents. The purpose of this paper is to highlight the need for alternative interventions in addition to other safety improvement strategies already employed on mines. It furthermore supports an existing paradigm: incident investigations. An investigation into fatalities in the South African mining industry shows that although great progress has been achieved through the reduction in fatalities in all sectors of the industry over the last few years, more can and should be done to achieve status of ?zero harm?. Fatalities and lost time injuries on mines result not only in large financial losses, but also in disruptions of mining operations in general through Section 54 stoppages to resolve the situation. The approach of the paper is therefore not to try and prove whether there is high fatality rate and/or lost time injuries, but in what way incident reconstruction simulations (IRS) can have an impact in the future prevention of such incidents. The challenge therefore lies in the utilization of pro-active systems that would show employees the possible outcomes of being exposed to certain hazards. In real life, these incidents cannot be re-enacted and in most cases we can only learn through the previous mistakes of others. A virtual reality (VR) education and training system will enable employees to be ?exposed? to different hazards in a safe environment, and simulation, in a ?forgiving? environment, of the possible consequences of unsafe acts. According to the Occupational Safety and Health Act (OSHA), unsafe acts and unsafe conditions are indirect causes of safety-related incidents, but there are also direct causes; for example, unplanned release of energy and/or hazardous material, and basic causes, for example, management safety policies, personal factors, and environmental factors. The administrative workload associated with any incident investigation places a large burden on the investigation team, and in most cases other employees are informed through vague administrative processes what the ?real cause? for the incident/accident was. New preventative strategies are often put in place without showing the employees what the real causes of the incident/accident were. This can be mitigated through the use of interactive VR simulations/animations of the hazards that they are exposed to and how to deal with them. If VR interventions are not used as proposed by this paper, the real causes and consequences of almost all fatalities and lost time injuries may never be fully understood. This paper also emphasizes what potential impact IRS could have on the prevention of future mine incidents as part and parcel of a pro-active risk prevention strategy. The intention is therefore not to replace any other risk prevention strategies, but to visually enhance the reality of the incident. Keywords virtual reality, risk management, incident reconstruction simulations, interactive safety training, usability context analysis, mine safety.

Jun 1, 2013

By Kedikilwe Oageng

Effective perimeter control during drilling and blasting is critical not only to blasting results but also to the overall stability of the pit over its entire life span. A pit where perimeter control is not given enough attention when conducting drilling and blasting operations, often experiences over-break or back break beyond final pit wall limits, and therefore has a relatively high probability of failure. Such a pit also becomes unsafe, sometimes not easily accessible, has increased loading costs due to production of oversize, longer cycle times and often problems are encountered when blasting subsequent benches. All these are undesirable consequences, which have negative cost implications. Specialised blasting techniques such as trim blasting and pre-splitting have over the years proved to be effective perimeter control measures. However, the success of these techniques is directly attributable to the time and effort given to the processes. This paper presents results of a project undertaken to monitor, review and optimize the trim blasting and pre-splitting processes at Orapa Diamond Mine in Botswana. The project was specifically incepted to improve the final wall conditions, which continued to deteriorate due to persistent over-break during blasting. The paper also analyses the results obtained against a benchmark of results taken prior to project implementation. Specific blast design parameters which are critical to blasting results were identified as problem areas after auditing of the pre-implementation drilling and blasting practices. These include drill-hole depth, spacing, splitting factor for pre-splits and timing of trim blasts. The impact of different rock types on the results was also studied, and recommendations were made at different phases of the project and results obtained after implementation analysed until optimum results were achieved.

Jan 1, 2008

By M. J. Little

Potgietersrust Platinums Ltd is Anglo Platinum?s only open pit operation and annually extracts 57 million tonnes of rock from 2 open pits. Over the past 3 years ~220 km of exploration drilling has been done, ~1000 km of rock face have been exposed for face mapping and over 7000 laboratory and field tests have been conducted. This has produced large amounts of geotechnical data to be utilised for feasibility studies, initial slope design and ongoing slope optimisation. It was necessary therefore to develop geotechnical databases to manage the vast amounts of data collected. SABLE and MineMapper 3D databases were created for logging and mapping respectively, with rock testing data incorporated into both. A pit inspections database was developed in MS Access and the existing groundwater and slope monitoring database was improved. The databases were linked to AutoCAD and Datamine to ensure that the latest geotechnical data is used for planning, draughting and modelling. The use of geotechnical databases ensures that no data is lost, standards are maintained and analysis can be easily performed. This increases the confidence of the analysis and allows the geotechnical engineers to optimise slope designs and blast designs on a regular basis. This reduces the risk of slope failure thus making the open pits more economical and safe.

Jan 1, 2006

By S. M. Brabyn

The wear in mild steel pipelines used to convey rod-milled waste backfill was determined and then compared with that obtained using a laboratory rig designed to simulate the wear condition in slurry pipelines. The relative importance of corrosion and abrasion was investigated under various conditions of water quality and particle size distribution. The laboratory rig was then used to evaluate other possible materials of construction for backfill pipelines. A preliminary assessment of the economic viability of pipelines made of alternative materials is included.

Jan 1, 1988

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

By J. O. Jensen

A method is described for the determination of cyanide in gold slurries, based on amperometry. The measured current is proportional to the concentration of cyanide, and is not effected by pH or by the concentration of oxygen in solution. It is also unaffected by other ions that may be present in gold-leaching solutions, including sulphide, thiocyanate, and thiosulphate. The current depends on the temperature, and an activation energy of 17,9 kJ/mol was determined Since the current is controlled by the mass transfer of cyanide to the anode, it depends on the conditions of agitation. In tests on an operational gold plant, slurry was pumped directly from the top of the leaching tank, through the measuring cell and back into the tank. The results indicate that the instrument is a promising alternative to the instruments currently available. The readings from the instrument remained in calibration for at least two days, showing that the instrument would need to be re-calibrated by the operating staff at regular periods.

Jan 1, 1994

By Ralph H. Nafziger

This paper reviews the major deposits of lower-grade chromite in the world, and a wide variety of methods used for the recovery of chromium from them. Gangue materials in more coarsely sized ores can be separated by gravity means, whereas flotation techniques are required for finer-grained materials. However, unless there is considerable Iron In the ores, physical means cannot increase the Cr/Fe ratios. Chemical techniques such as hydrometallurgical methods, chlorination, roasting and leaching, and smelting are required for this purpose. A greater understanding of the physical properties of chromites and the chemical reactions that take place in the recovery operations is required before. the recoveries from lower-grade chromites can be maximized. More efficient recovery operations can be realized If It can be shown definitively that the reduction of chromites occurs via either a gas-solld or solid-solid mechanism, for example. The effects of specific impurities on the chromite reduction reactions need to be better understood, as do reagent and pH control in the flotation of chromite.

Jan 1, 1982