Search Documents

By K. Ward

The Environmental Protection Agency (EPA) is beginning to provide compliance assistance visits to various industries, including mining, for Emergency Planning and Community Right-to-Know Act (EPCRA) compliance. The EPA inspectors may consist of a multi-media team deployed to review systems and procedures for EPCRA Sections 302, 304, 311, and 312. The Team’s focus may include emergency response plans, training programs, qualifications of personnel, and release notification protocols. This presentation takes a look at the EPCRA compliance challenges faced by Arizona copper mining and processing facilities.

Jan 1, 2001

By I. Duckworth

P.T. Freeport Indonesia operates a mining complex located in the highlands of Papua, Indonesia. This district consists of underground and surface operations. The East Ertsberg skarn system (EESS) is one of the major orebodies in this district. Subsurface caving of the EESS has been carried out in a systematic series of mining lifts dating back almost 30 years. Present production from the third lift deep ore zone (DOZ), has reached 80 kt/d (88,000 stpd) during 2010, with this rate sustained through 2015. The orebody was proven below the existing caving level, with the next vertical block called the deep mill level zone (DMLZ).

Jan 1, 2010

By J. A. Organiscak

Longwall mining technological improvements have provided significant increases in productivity over the last 15 years. Longwall productivity is anticipated to continue to escalate with expanded application of automated equipment. Automation technology that will likely be adopted over the next 5 years is memory cut with shearer initiation of shield movement supervised by a couple of face workers. Operations using this technology will most likely relocate many production workers from the face to the outby gate entries and position several face workers outby the shearer, exposing workers to different health and safety risks. These changing risks are primarily related to worker relocation and expected increased production levels. Workers outby the face will most likely have less dust and noise exposure, but will be exposed to other safety hazards associated with outby equipment movement, materials handling, and gate entry ground movements. The face workers will most likely be exposed to higher respirable dust and noise levels generated by the equipment at elevated production rates. Methane gas emission is also expected to increase with faster mining rates. These operational changes and the control technologies needed to reduce redefined longwall worker hazards at semiautonomous longwall operations require examination to maintain the health and safety of mine workers.

Jan 1, 1996

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By CHRISTOPHER D. HEBERT, SCOTT W. HOFFMAN

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2019

By M. Perolo, A. Contini, E. Ramelli, G. Borgonovo, L. Locatelli

This paper presents the ground settlement monitoring system used during the construction of two tunnels bored by two EPB TBMs, beneath the existing and active railway embankment in Bologna (Italy). The tunnels run close to large buildings and beneath bridges and other infrastructure. Data are collected from remote total stations and from electro levels installed directly on the railway tracks. The automated monitoring system acquires and analyses data then sounds an alarm in the event that there is a problem. Alarms are sent out in case of excessive tilt or settlement. Data is provided through a dedicated web application for multiple-party access, to gather, manage and store monitoring data.

Jan 1, 2007

By Eduardo M. Sacris

The performance of the grinding circuit, from the initial stages of operation to the present, is discussed. The mill efficiency as measured by the Bond grindability data and the operating work index is presented. The objective has been to produce a sand cyclone overflow containing not more than 6% +65 mesh. However, this has never been attained even at low milling rates. On the other hand, significant improvements in throughput were achieved by instituting some equipment changes and process modifications within the grinding circuit. The latest approach to solving the coarse grind problem is also discussed.

Jan 1, 1983

By W. G. Brunner

The slurry wall technique has undergone an evolution from its invention to its today’s status. In the early stages slurry walls were built with cable grab, later on with much stronger hydraulic grab and last but not least with the use of the cutter technique. The cutter allows thick walls with high verticality to extreme depths through hard soil and rock formations. With the rising demand of the construction of watertight diaphragm walls different joint systems have been developed. In addition to the rapid development of excavation systems it was necessary to improve slurry treatment and desanding plants, especially in conjunction with high performance trench cutters. Deep mixing methods can be used economically for the construction of cut-off or excavation support walls where other systems such as traditional soldier beams and lagging walls would yield unsatisfactory performance, where the installation of vibrated or driven sheet piles could cause vibration induced settlements and where concrete diaphragm walls would be time consuming and expensive. The new CSM method can largely replace the more conventional single or multiple auger methods of soil mixing or jet grouting. The cutter tool is similar to a cutter used in diaphragm walls or cut-off walls and is operated with a Kelly mounted on a drilling rig or rope suspended on a crane jib or mast of a base carrier. With this system much deeper walls can be installed and even hard soil layers can be penetrated.

Jan 1, 2007

By Ivo Dreiseitl, Kondratenko. Anatoly

"The second prime area within the Interoceanmetal Joint Organization exploration area named H22 was delineated in 2013 with the goal to ensure sufficient nodule reserves for profitable mining operations and processing.The knowledge base for area H22 has been obtained from archive materials. The geological situation can be characterized as follows: the sea bottom is represented by tectonic blocks oriented in a sub-meridional direction. According to swath mapping, the depressions (troughs) are contoured at depths of 4500-4600 m while the tops of horsts occur at 4300-4350 m. Volcanic relief occupies 6% of the H22 area; in the eastern part a multicone volcano was detected. Its area at the base is 153 km2. The maximum height of a cone above the base is 850 m. The crystalline basement composed by tholeiitic basalts of late Oligocene age is covered by about 100 m of sediments. Semi-consolidated to consolidated calcareous nanofossil sediments of the Marquesas formation are deposited on the basement. Higher up in the profile sediments of the Clipperton formation occur. They are represented by unconsolidated siliceous (Radiolaria, Diatom) ooze. Sediments containing calcium carbonate have not been detected. Where opaline silica (or CaCO3 if any) content is below 5%, the sediments belong to zeolitic clays or red pelagic clays. Grain size composition of the seabed and the near-seabed sediments in H22 classifies them into clayey silts."

Sep 1, 2014

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By Tim O’Neil

Nearly 4,800 mining professionals and exhibitors occupying 580 booths attended the 2000 SME Annual Meeting and Exhibit, Feb. 28-March 1, in Salt Lake City, UT. The technical program included80 sessions and four specialty symposia: bulk material handling, control 2000, minor elements 2000 and plant operaters. Meeting highlights included the keynote session. Executive shared their perspectives on pivotal issues and approaches to address the challenges of the new millennium. SME has begun planning for its 2001 Annual Meeting, Feb. 26-28, in Denver, CO. The meeting carries the theme “2001 — A Mining Odyssey.” A call for papers has been issued and exhibit space is 80% reserved. For information, visit SME’s website, www.sme-net.org. Or write Box 625002, Littleton, CO 80162-5002,ph 800 763 3132 or 303 973 9550, fax 303 979 3461, or email meetings@smenet.org.

Jan 1, 2000

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960

By Carl G. Bock

INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has let a contract for the excavation of three rock stations, spaced about 3550' (1082m) apart, beneath Connecticut Avenue in Washington, D.C. Two previous rock stations have been completed, one of which had a crown pilot tunnel excavated to explore geologic conditions that would be encountered during the station excavation. This pilot tunnel was primarily for inspection by bidders and design was based on core hole information. The other rock station had no pilot tunnel and was also designed on the basis of core hole information. The three rock station areas, which are the subject of this paper, have been explored by crown pilot tunnels and an as-built report, with geologic maps and sections, has been prepared, for use by the design engineer as the basis of design for support of the structures. The geotechnical report describes the geologic structure in detail and relates it to excavation and support of the three crown pilot tunnels and the running tunnels which will be enlarged to create the 58'W x 44'H x 700'(+)L (17.6m x 13.3m x 212m +) stations. The information was complete enough to permit the design engineer to visualize the geologic structure and compute loads for the various types of rock conditions. It was therefore possible to determine the size and spacing of the steel sets for the several different conditions of rock structure encountered in the pilot tunnels.

Jan 1, 1976

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage organizations to work together, executing such risk assessments comes with challenges. This paper focuses on one trona mine’s experience in the development and implementation of a field level risk assessment program to help its entire organization understand and manage risk to an acceptable level. Through a transformational process of ongoing support and communication, Solvay Green River fostered a culture of trust and safety grounded in risk assessment, safety interactions, and hazard correction. The application of consistent risk assessment (RA) tools was critical to create a participatory workforce that not only talks about safety, but actively identifies energies that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s process of RA implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks. As discussed, consistent efforts to establish a participatory risk management program are worth the initial struggle to ultimately reduce incidents. INTRODUCTION Work-related health and safety (H&S) incidents often account for lost days on the job, contributing to organizational/financial and personal/social burdens [1-2]. Accompanying research demonstrates that risk and ambiguity around risk contribute to almost every decision that individuals make throughout the day [3-4]. In response, understanding individual attitudes toward risk has been unquestionably linked to predicting H&S behavior [5]. Although an obvious need exists to identify more comprehensive methods to assess and mitigate potential hazards, some argue that risk management is not given adequate attention in occupational H&S [6]. Additionally, research suggests that a current lack of knowledge, skills, and motivation are primary barriers to mitigating workplace risks [3-6]. Therefore, enhancing knowledge and awareness around risk-based decisions, including individuals’ abilities to understand, measure, and assign levels of risk to determine an appropriate response, is increasingly important in hazardous environments to predict and prevent incidents. This paper focuses on tailored approaches to field level risk assessment (FLRA), measurement, and common barriers to participating in such activities. The authors use a trona mine in Green River, Wyoming, as a case study to illustrate how the organization overcame widespread and site-specific challenges to implement a proactive risk management program. By discussing the mine’s tailored FLRA program, this case study contributes to the literature by first, providing examples of critical components that need to be in place to ensure successful risk management and second, context for continuous quality improvement that can foster a higher level of trust and empowerment on site."

Jan 1, 2017

By J. G. Pippenger

Rio Tinto Coal Australia (RTCA) developed the Meandu Mine in Queensland, Australia in 1983 to supply thermal coal to the adjacent and newly constructed Tarong Power Station (TPS). In designing the mine, RTCA selected Meandu?s best economic reserves for a 27-year life based on station owner Tarong Energy Corp.?s (TECs) estimated life for TPS. That 27-year plan changed dramatically in the early 2000s when TEC approved life extensions to TPS?s four existing units plus construction of a fifth unit. After reviewing Meandu?s remaining reserves, RTCA decided the nearby Kunioon reserve offered the more economic option for maintaining deliveries beyond 2010. Those plans changed again in 2007 when TEC chose to purchase the Meandu Mine and nearby reserves. TEC then selected Thiess Pty Ltd. (Thiess) to continue operating Meandu until the new mine at Kunioon could be developed. After assuming operation of the mine in 2008, Thiess began a review of Meandu?s remaining reserves and found considerable coal available with economic potential. Working jointly with TEC, Thiess performed several analyses on Meandu and subsequently the Kunioon coal reserves. The results changed TEC?s decision from expediting Kunioon?s construction to instead continuing Meandu?s operation for up to 15 additional years.

Jan 1, 2011

By R. E. Murray

"It is a gloomy moment in the history of our country. Not in the lifetime of most men has there been so much grave and deep apprehension; never has the future seemed so incalculable as at this time. The domestic economic situation is in chaos. Our dollar is weak throughout the world. Prices are so high as to be utterly impossible. The political cauldron seethes and bubbles with uncertainty. Russia hangs, as usual, like a cloud, dark and silent, upon the horizon. It is a solemn moment. Of our troubles, no man can see the end." By now you, no doubt, are asking, 'Where did Murray get this bit of philosophy?' Well, I obtained it from an editorial entitled. "The Worst of Times", which was published in the Harper's Magazine in 1847. That's right, 1847! The parallelism between the situation in our country at this time and in 1847 is un- canny. But wait, there is one major exception the size of government. To my knowledge, the citizens of 1847 were not stifled by the extreme governmental excesses that we are experiencing today.

Jan 1, 1980

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By Mark C. Russell, Charles T. Russell, Brooke Colburn, Parker Bailey, Desiree Bernhard, Kaito Durkee, Tristen Cutshall, Rob P. H. Urselmann

Hypersonic tunnel boring (HTB) uses directed, high velocity projectile impacts to remove rock. HTB is highly independent of rock strength and targets hard, abrasive rock and variable rock environments. This paper discusses history, theory and presents test (2×2 m and .75×.5 m tunnels) field trial results and technical and economic evaluation. The HTB tests are compared against the historic ‘project REAM’ and the concept against tunnel boring machines and drill & blast in design studies for full-scale 12 m and 4.5×5.5 m tunnels. The positive results indicate that under these conditions HTB can replace Drill & Blast and Tunnel Boring Machines.

Jun 13, 2021