Search Documents

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Most, if not all longwall gobs contain explosive gas zones (EGZs), i.e., zones of explosive methane-air mixtures that can cause – and have caused – mine fires and explosions. If the coal is prone to spontaneous combustion, oxygen penetration into the gob must be avoided. This paper summarizes the significant research findings from five years of computational fluid dynamics (CFD) modeling research conducted at the Colorado School of Mines (CSM) under funding from the National Institute for Occupational Safety and Health (NIOSH). CSM Researchers have developed CFD modeling techniques to identify where and under what circumstances EGZs can form in longwall gobs and how EGZ formation and oxygen penetration depend on the ventilation method, face and bleeder ventilation parameters, injection of inert gases and the operation of gob ventilation boreholes. Recognizing these explosion and fire hazards is an important first step in improving the safety of longwall coal mines. CSM modeling research has shown that EGZ formation can be effectively controlled by adjusting ventilation parameters, choosing the proper ventilation pattern and injecting inert gases where necessary. INTRODUCTION In a project sponsored by the NIOSH Office of Mine Safety and Health Research, researchers at the Colorado School of Mines have examined gas compositions and flows in longwall gobs in order to assess explosion and fire hazards. Since gob areas are inaccessible, researchers developed a series of computational fluid dynamics (CFD) numerical modeling tools to characterize these hazards. A variety of CFD models were developed to cover progressively sealed as well as bleeder ventilated gobs for both coal and trona mines. The explosion and fire hazards posed by EGZs in longwall gobs can be summarized as follows.• If the EGZ lies closely behind the longwall face, flames and pressures from an explosion can penetrate the shield supports and reach the active face area, creating blast trauma, burn hazards and toxic, unbreathable atmospheres. • EGZs can be pushed around inside the gob by roof collapses and cave-ins. If they get pushed out into the face area, sudden methane inundations and explosion hazards in face areas can result. • Fresh air flowing into the gob can create an explosion hazard as the gas composition in the gob moves from fuel-rich inert to explosive, creating EGZs. • Ignition sources inside the gob can be frictional ignitions or spontaneous combustion. • Bleeder ventilated gobs are surrounded on all sides by an EGZ that forms along the fringe areas between the fresh-air ventilated bleeder entries and the methane-rich interior of the gob. It is suspected that diffusion flames can propagate rapidly along these EGZ fringes if an ignition occurs"

Jan 1, 2015

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By C. A. Rowland

The use of the Bond Work Index to size industrial grinding equipment is well known. Its use to measure grinding efficiency was presented by C.A. Rowland, Jr. at an AIME meeting in 1976. However, due to a bureaucratic error, the paper was never submitted for publication. This metric has nevertheless been adopted by industry as a widely used standard. The purpose of this paper is to re-present and update the application of this tool as a standard for measuring grinding circuit efficiency. Definition ?standard, n. something established for use as a rule or basis of comparison in measuring or judging capacity, content, extent, value, quality, etc.; as standards of weight and measure? (Webster, 1958).

Jan 1, 2008

By Yuexin Han

The characteristics of comminuted hematite products using a high pressure grinding roller (HPGR) and conventional jaw crusher (JC) were comparatively studied by screening, optical microscope, scanning electron microscope (SEM) and Brunauer, Emmett and Teller (BET) techniques. Major properties investigated included product size distribution, particle cracks, specific surface areas and pore volumes. Results showed that in a closed-circuit operation with a screen opening of 3.2 mm, the HPGR and JC gave a similar P80, but the HPGR achieved a more uniform size distribution, more fines and a higher crushing efficiency. Three modes of cracks were identified, namely transgranular cracks, innergranular microcracks and intergranular microcracks. Transgranular cracks originated from shearing breakage. Innergranular and intergranular microcracks were generated by HPGR via the two main nonrandom breakage forms, preferential breakage and interfacial breakage, depending on their respective ability to endure stresses when mineral phases (particles) were loaded against each other. The BET values for the same-size fractions showed that HPGR products gave higher specific surface areas and more pore volumes than JC products. This indicates that HPGR-crushed products are easier to grind because of their high porosity and extra cracks.

May 1, 2012

By G. Wang, L. R. Moore, Y. Xiong, A. Gorken

"Feldspar may represent 60% of the earth’s crust, but the mineral does not exist in a pure state. It is generally associated with quartz, iron containing minerals such as mica, and titanium containing minerals such as rutile. Feldspar itself can even exist in different lattices from those containing sodium to various divalent ions. As such, its beneficiation has become a process that is quite complicated, when compared to the beneficiation of other minerals. It is this complexity that has made feldspar beneficiation dependent on tailor made reagents to successfully yield the industry specified feldspar products. This paper reviews the mineralogical variations found from two feldspar mines and the development of collectors to specifically target a Fe+Ti concentration of < 0.05%, while maintaining a feldspar recovery greater than 90%.INTRODUCTION Feldspar is a class of aluminum silicates that represents the most abundant mineral on earth (Vidyadhar, 2002). This class of mineral can further be defined by the types or concentrations of cations present in the crystal lattice, MAlSi3O8 (M = K, orthoclase and microcline; M = Na, Albite; M = Ca, Anorthite) (Heyes, 2012). Feldspar is most commonly mined and processed for either the alumina used in glass making or for the alkalis used in ceramics. The alumina is known to improve product hardness, durability, and resistance to chemical corrosion. The alkalis act as flux, which means they not only lower the melting temperature of the mineral mixture, but also assist in connecting the other components present in ceramics. It was stated in 2009 that the world production of feldspar was in excess of 18.3 million tons produced, with the majority coming from China, Italy, and Turkey. Raw feldspar is typically found with quartz, iron containing minerals such as mica, titanium containing minerals such as rutile, and other feldspar minerals (Celik, 2001). Quartz is stated as having a negative effect on the melting point of the feldspar, whilst the iron and titanium based mineral contaminants are known to have negative effects on color and quality of the product produced; these mineral contaminants must therefore be separated prior to application (Barns, 1997 & Celik, 2001). Mineral flotation and magnetic separation are the most common means of feldspar beneficiation. However, conditions vary greatly from mineral contaminant to mineral contaminant (Table 1). Some literature suggests feldspar can be floated with an amine, but this generally yields lower than acceptable recoveries and often still requires the magnetic separation of iron based minerals to achieve the desired grade (Amarante, 1997 & Heyes, 2012). Feldspar flotation can be further improved with the addition of hydrofluoric acid (HF) as a silica depressant and feldspar surface modifier, but this still requires the removal of some of the other minerals first. Rutile can be floated with an anionic fatty acid collector at a pH range of 7-8 or with a petroleum sulfonate at a pH < 4 (Celik, 2001), while mica can be floated with a petroleum sulfonate or an amine collector at a pH of 3.5."

Jan 1, 2016

By David Wright, Jerome Chamfray, Anthony Harding, Brian Boye

Conway’s Law states that unless we intentionally design automation tools around what we need, we will simply replicate our existing processes. While we may achieve some savings this way, there is an opportunity for greater benefits if we re-imagine the way we, as an industry, perform design. This paper examines current technology and shows how even small departures from merely encoding what we currently do could reap significant benefits. From these examples a framework is developed for a new and innovative approach tvo automation that will allow us to design more quickly, to a higher quality, and communicate outcomes more effectively.

Dec 1, 2022

By R. L. Guerguerian

Hydrostatic trunnion bearings were recently provided on large Semi-Autogenous Grinding (SAG) mills driven by wraparound motors assembled on the head to shell flanges. A conventional SAG mill would have a ring gear driven through one or two pinions. The effects of the magnetic air gap forces from this new SAG mill drive arrangement on the performance of the bearing are discussed. A step-by-step systematic analytical de-sign of the hydrostatic trunnion bearing is presented, followed by a discussion of grinding mill erection requirements to conform with the design. A brief comparison with other bearing types and their response to the effects of magnetic air gap forces are also presented.

Jan 1, 1992

By F. H. Buttner

Commodity currency intrigues most of us because of the problems it offers to solve for the Third and the First Worlds. What problems might be solved, if commodity currency were to be adopted in the Third World? That is really the question we are probing here right now. It would take a while to think through all their subtle consequences of this question, but, off the top, it might well have at least three important impacts. Most important of these to this audience is relief from unfair Third World competition. Second, it might well liberate Third World economies from financial indebtedness to the First World and give them freedom from the liquidity limitations. The third benefit is that it might help relieve World trade tensions. All three benefits are interrelated. We could start our speculations on the application of commodity currency from anyone of these starting points. But let us use the starting point most important to you, unfair competition to the U.S. mining industry. From there we might wind up with some thoughts on things you, yourselves, can do to improve things.

Jan 1, 1978

By M. Allan Holtz

The shipment of coal, ores, and minerals in bulk form during the winter months presents a difficult problem in emptying rail cars. U. S. Steel Research in cooperation with U. S. Steel Coal Operations bas laboratory tested and field monitored the effectiveness of using freeze conditioning agents (FCA) to minimize the frozen coal problem. This report examines, in an overview manner, our experience after four seasons of treatment using different FCA agents on raw and preparation plant products. Our observations indicate that if an FCA is applied correctly it is effective mineral to mineral. Freezing problems still occur at the interface between the coal and the metal of the car sides and bottoms. Leading chemical suppliers have made positive improvements in their FCA formulations with second and third generation products. Further advances are needed to make chemical treatment for the prevention of frozen coal a real full-proof method.

Jan 1, 1980

By K. V. K. Prasad

Forecasting mined grade variability from exploration information is a challenging task in mine planning. For effective planning of activities such as workplace scheduling, ore grade quality control etc. development of realistic numerical/simulation models of in-situ variability from exploration information is an essential first step. Geostatistical conditional simulation (GCS) is one of the well known methods to develop these simulations. Recently, stochastic fractal models based on the assumptions of scale-in variance and self-similarity have been used for developing simulations of several natural phenomena. It has been suggested that these models might permit generation of short-scale variability information from exploration data with greater fidelity when the data satisfies the attendant assumptions. In this paper the stochastic fractal models are reviewed and their relationship to geostatistical variogram models is examined. A comparison of the two simulation techniques has been per-formed using coal sulfur data from a mined out coal property. The results of this comparative analysis are also presented in the paper.

Jan 1, 1992

By W. R. Reed, W. J. Archer, A. B. Cecala, J. D. Potts

The U.S. National Institute for Occupational Safety and Health (NIOSH) uses light-scattering real-time dust monitors (nephelometers) in its research to develop dust controls to reduce respirable silica dust overexposures in miners. Recently, the model 1500-pDR, an active nephelometer (i.e., with cyclone and pump configuration), was introduced by Thermo Scientific. Testing was completed to ensure compatibility with the metal/nonmetal mine dust personal sampling unit (M/NMDPSU). Results of testing demonstrated that gravimetric concentrations measured from the 1500-pDR are comparable to the gravimetric concentrations measured using the M/NMDPSU, without need for correction, under commonly observed dust loading conditions.

Jan 1, 2012

By M. J. Shulman

An algorithm used by the US Coast Guard to find lost objects is utilized to optimally allocate exploration efforts during initial stages of an exploration program. Based on classical search theory, the algorithm assumes a target probability distribution function, a detection func¬tion, and a cost function. The three Junctions are analogous to delineating areas of possible mineralization, choice of exploration methods, and exploration budget. Application of the algorithm is shown for a hypothetical target distribution. Using the maximum number of field days available as the cost function, the optimal allocation of effort is shown for different exploration methods, e.g. electromagnetic survey and induced polarization. The adaption of the algorithm for the exploration process is discussed.

Jan 3, 1984

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,&apos; to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By M. R. Carter

The Rochester Mining District is located some twenty-five miles NE of Lovelock, Nevada. The District was discovered and named in the 1860&apos;s by prospectors from Rochester, New York. For a number of years, they worked Rochester Canyon, sinking shafts and inclines and making open cuts. After reaching a depth of approximately eighty feet, the miners tapped an underground channel and were driven from these workings by a strong flow of water leaving pumps in the shaft and barely escaping with their lives. With the Rochester workings no longer accessible, the miners went to the southeast and established the Relief Mining District. About 1881, gold was found in the gravel at the mouth of American Canyon, to the east of Rochester. These placers were worked until 1895, first by the Americans who reportedly took out $1 000 000, and later by the Chinese who mined the gravel with great skill. It was estimated that the Chinese took out as much as $10 000 000.

Jan 1, 1987

By C. Haycocks

Damage prediction during multi-seam mining is an essential precursor to optimizing mine design. Ground control problems associated with interaction are influenced by both fixed geological and site conditions as well as mining variables which may be controlled to varying degrees. To quantify interaction effects across an affected seam a hazard map approach was selected, which allows interaction data to be presented in a form that can facilitate future planning. Study mines were analyzed using boreholes as sources of geological and spatial data, together with information from mine maps which gives the extent of mining activity. To demonstrate the method the safety factor against interactively caused shear failure in the lower seam roof was computed. Input data included depth of cover, inner burden thickness, remnant pillar size, extraction ratio, immediate roof type, seam thickness, percent sand-stone, and rock strength values. These safety factors were then contoured to produce a hazard map. An assumption was made to assign a high safety factor at the outcrop line to permit realistic contouring of the safety factors. The software also allowed mine workings to be drawn onto the map to facilitate interpretation of the overall results. Hazard analysis permits delineation of unsuitable mining areas within a seam. The application of the method for refining mine design and improving reserve recovery is verified using case studies.

Jan 1, 1992

By K. Luxbacher, A. Haghighat, B. Lattimer

Mine face ignition due to high levels of methane is one of the most common fire incidents in underground coal mines. In continuous miner headings, depending on the magnitude of the ignition or resulting fire, auxiliary ventilation controls may be damaged or dislodged, affecting the ventilation into the area. A computational study was conducted to investigate the effects of different levels of damage to an exhausting ventilation curtain in a continuous miner heading, and the impact on ventilation to the face. The computational fluid dynamics software Fire Dynamics Simulator (FDS) Version 6.0 was used to predict the conditions that develop due to a 200-kW fire in the face following a methane ignition with different levels of assumed ventilation curtain damage. Smoke layer depth, temperature and mass flow inby the last open crosscut were used to evaluate the impact of no damage to the curtain, partially dislodged curtain, and fully removed curtain. As more of the ventilation curtain was damaged, smoke depth and temperature outby the fire increased. With the full removal of the curtain, the smoke accumulated from the last open crosscut to the face, with the ventilation completely bypassing the continuous miner region.

Jan 1, 2016

Contents

Jan 1, 1985

By Sun Guangzhong, Liang Jinhuo

Adverse geological condition is a major factor which makes construction difficulty in tunneling. But if it is predicted and tunnel support is made efficiently in time, the above difficulty can be reduced. It is necessary to develop one or several effective and economical geological methods for prediction of tunnel geology while expensive and time-consuming instruments are used. This paper reviews and proposes several geological methods for prediction of fault, seam, contact zone, and groundwater inrush. These methods have been proved to be effective and economical in tunneling practice in China.

Jan 1, 1987

By G. E. Jones, G. K. Hoffman

Through the USGS National Coal Availability pro-gram, two San Juan Basin studies have been completed. The study areas are in the northwest Bisti field, Fruitland Formation and in the eastern Standing Rock field, Menefee Formation. Original resources are 4.66 Gt and 3.46 Gt (5.14 billion stand 3.82 billion st), respectively, in the Bisti and Standing Rock areas. Bisti coal resources are greatly reduced by the Bisti-De-Na-Zin wilderness area (1.13 Gt (1.25 billion st)). Technological restrictions remove 31% from Standing Rock original resource. Available resources are 60% (2.79 Gt(3.07 billion st)) of the Bisti original resource and66% (2.26 Gt (2.49 billion st)) of the original Standing Rock resource.

Jan 1, 2000

By K. J. Reid

With the current trends of increasing costs and decreasing head grades the mineral industry is no longer operating in very high profit areas and has been forced to pay greater attention to the application of modern technology. Although here are many technological advances to the credit of the industry in recent years there are still many processes being operated in the traditional manner and still many areas awaiting the application of methods which have been proven in other industries. Compared with the chemical industry the mineral industry is seriously ageing in the general areas of process analysis and process control, more so than can be justified by the complications arising from having to deal with particulate systems with properties far different from ideal, or even non-ideal, liquid systems. One area in which there has been a remarkable lack of application in the Mineral industry is that of analog computation and the authors feel that there is considerable scope for the use of the analog computer in studying mineral industry processes. The paper outlines the basic principles and features of the analog computer and describes its role as a simulation tool in some engineering and mineral processing systems.

Jan 1, 1972