Search Documents

By S. K. Kawatra, T. C. Eisele

Microorganisms, such as the bacteria Thiobacillus ferrooxidans, have been reported to depress pyrite flotation (Elzeky and Attia, 1987; Atkins, 1990). However, the depen¬dence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms (chemolithotrophic bacteria, chemoorganotrophic bacteria and yeast) over the pH range of 2 to 12 was studied. Screen¬ing tests using microflotation showed that every microorgan¬ism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with both mineral pyrite and coal pyrite using Thiobacillus ferrooxidans and Saccharomyces cerevisiae as depressants, showed that these microorganisms are very effective depressants for mineral pyrite at acid pH, but they are largely ineffective at neutral and alkaline pH, where the mineral pyrite surface is not naturally hydrophobic. The flotation response of the coal pyrite was completely different from the mineral pyrite. The coal pyrite was most floatable near neutral pH, with the floatability decreasing in acidic or alkaline solutions. De¬pression of the coal pyrite by yeast was not selective between the pyrite and the associated coal under the experimental conditions.

Jan 1, 2000

By R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (K088) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron-and steel making and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By L. Shevenell, L. Stillings

The Acid Drainage Technology Initiative-Metal Mining Sector (ADTI-MMS) has established a Pit Lake Committee to enhance the science and understanding for the long-term management of pit lakes. Participation in this new committee is from members of federal and state agencies, industry, and academia, including numerous individuals representing 10 states. Work has begun on a pit lake literature search and review, database, classification, and sampling and monitoring procedures document. Coordination with the International Network for Acid Prevention (INAP) has been established. Future work will include preparing a prediction and assumption verification document, a report identifying variables upon which water quality is dependent, and an applied remediation technologies document, including an evaluation of the effects of backfilling.

Jan 1, 2002

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By Warren C. Gerler

An overland belt conveyor system is installed for only one reason to save money. It must pay its way on a ton-mile basis over a stated period of time, and do so in competition with other forms of transportation. Such a system with its economies has recently been installed at Simco-Peabody's mine near Coshocton, Ohio by Link-Belt Company. Three miles in length, this system carries coal from open pit and underground mining facilities to the Conesville Power Plant of Columbus & Southern Ohio Electric Company. The coal was formerly trucked from the mine direct to the power plant; but over the years the mining operations have moved progressively farther and farther from the plant, making the over-the-road hauling distance correspondingly greater. Simco-Peabody has mining operations over a considerable area just east of the Conesville Station. The majority of the coal is recovered by conventional strip mining. Some underground mining` is performed by the high wall method.

Jan 1, 1963

By J. C. Gathje

The Robinson copper ores were mined for many years from pits containing varying ore grades, sulfide and oxide ore types, and differing mineralogy. The ores also contain gold and molybdenum values, and their recoveries are an integral part of the flowsheet development. Metallurgical responses were characterized using a standard flotation procedure. Further studies investigated primary and regrind particle sizes, reagents, and other variables. The metallurgical testing was supported by mineralogical studies. Results demonstrated a high degree of metallurgical success for flotation. Final copper concentrates ranged in grade from approximately 28 to 30% copper and copper recoveries were 89 to 95% based on laboratory and pilot plant data.

Jan 1, 1992

"Metallurgical process development in greenfield projects must define the comminution flowsheet and establish the equipment sizes that are required to deliver the project design criteria. These are critical steps that heavily influence the financial performance of the project, requiring a detailed understanding of the ore properties of the project resources and the best practice methods to size comminution machines. This paper reviews current practices for determining the ore characteristics relevant to comminution circuit design. Particular attention is given to the design of sampling and testing programs, and the methods commonly applied to size crushers and mills for conventional size reduction applications in mineral processing. IntroductionMetallurgical process development in greenfield projects requires the selection of a comminution flow sheet and must establish the equipment sizes required to deliver the project design criteria. This necessitates a detailed understanding of the ore properties that define the project resource. For brownfield projects the same objectives may apply for plant expansions, or the project objective may be simply to define the capacity and operating cost of an existing facility for a new ore source. The process development phase in either instance will typically comprise the following key activities:• Geometallurgical classification and sampling of the ore deposit or deposits.• Determination of comminution energy requirements.• Benchmarking similar projects.• Identification of flow sheet options.• Equipment selection and sizing.This paper is concerned specifically with process development testing and will as such focus on the first two activities on the list: sampling and testing of the deposit. The discussion will focus on testwork programs to support the design of comminution circuits commonly in use in mineral processing today, specifically crusher, tumbling mill and stirred mill technologies.It is important that any testwork program is designed giving consideration to the types of flow sheets that are viable for the project, and the data that will need to be generated to support the final equipment sizing. Designing a testwork program to only provide information about one particular type of flow sheet will not allow sufficient information to be generated for a rigorous trade-off analysis of options, and may therefore preclude financial optimization of the project. Testing programs should be designed to collect sufficient data to ensure that any backtracking at a later stage to fill in missing information is minimal."

Jan 1, 2016

By L. G. Hagenbuch

Several factors need to come together in creating an integrate mining equipment dispatching system. At the hub of these factors ace the central dispatching formulas. This paper details the development of these central dispatching formulas and explores the combining of these formulas with other elements to create an integrated dispatching decision. WHY DISPATCHING? Truck dispatching implies and in reality should equate to mine equipment efficiency. Good truck dispatching will yield good mine equipment efficiency while poor truck dispatching will yield the alternative. Truck dispatching can either be automated through a computerized, process or it can be manual. Every mine with haul trucks has a truck dispatching system whether it is recognized or not. Even a system wherein the hauler operators determine where they are going for their next load is a truck dispatching system.

Jan 1, 1987

By M. Di Tommaso

Acid Mine Drainage (AMD) is a quite diffuse environmental problem in dismissed sulphur mine districts. AMD is related to sulphur oxidation of abandoned tailings, generating heavy metal-bearing streams with high iron and sulphate contents and low pH. Treatments of AMD aim firstly to increase the pH to reduce its leaching power causing the further release and mobilization of heavy metals through soil solution and groundwaters. Increasing the pH also allows the precipitation of iron (III) (involved in sulphur oxidation and then in AMD generation) and the partial removal of other toxic components such as arsenic. pH adjustment and the reduction of the high concentration of iron are also necessary for the successive biological treatment in permeable reactive barriers (PRB) with sulphate reducing bacteria (SRB) (II step, biologically mediated precipitaton/biosorption) to avoid the rapid plugging of the barrier (for the large amounts of iron precipitates) and to ensure neutral pH conditions for SRB growth. In this work the first step (chemical precipitation) of a combined chemical and biological treatment of AMD is presented. Experimental data from column tests using carbonate stones to remove iron and increase pH were reported. Toxicity tests have been carried out on the treated wastewaters by Lepidium sativum.

Jan 1, 2006

By J. P. Wilson, T. Cook, H. Kling

The Tessenderlo-Kerley Leachprocess has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia andammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By D. Anthony, R. A. Williams, R. Raponi

Barrick Gold Corporation in conjunction with SNC Lavalin Engineers and Constructors have developed basic engineering design for counter current decantation thickener (CCD) plants capable of processing 44 000 t/d. To achieve this throughput in a single train, the largest high-rate thickeners installed to date have been utilized in concert with large process slurry and solution transport systems. Process reliability and plant operability and maintainability have been carefully considered in order to develop a practical, yet cost effective design. The design also incorporates the challenges associated with installation of large equipment and structures in a remote location, with a climatically hostile environment, situated in a high seismic activity zone.

Jan 1, 2002

By V. Ciribeni, R. J. Ferretti, C. de Arrieta, E. E. Rossi

The relationship between collector concentration and the solution pH at which flotation occurs is discussed for different minerals. When flotation results are plotted as log of the concentration against pH, the values define areas of total, partial or no flotation. The experiments were performed in three different conditions: a) floating with the same solution used for conditioning; b) floating with water at the same pH as the conditioning solution; and c) floating with water at pH = 7. In each case, the results obtained are quite different. It is suggested that the presence of a second layer of collector reduces flotation over some domains in the graphs. These domains are called depression areas.

Jan 1, 1992

By Tom Ireland, Sumi Eratne

The approach to Risk Management during the procurement of major projects often has a significant outcome on the ultimate successful delivery of a project. The $NZ4.4B Auckland City Rail Link project is the largest and most complex transportation project yet undertaken in New Zealand. Risk management prior and during procurement was undertaken in accordance the ITIG Code of Practice for Risk Management of Tunnel Works (TCoP) and through the use of an Alliance Geotechnical Baseline report. This paper describes the measures taken during the procurement process to achieve certainty with respect to outcomes and minimise project risks whilst also achieving value for money. This included the use of cloud-based delivery of geotechnical data and 3-D geological models, reducing tendering costs and allowing a focus on risk mitigation measures during the tender rather than data management.

Jun 13, 2021

By M. A. Chandler, G. T. Adel, J. N. Richardson, E. C. Gutierrez

A rapid, bench-top analyzer has been developed to determine P2O5 content and CaO/P2O5 ratio in phosphate ores. The analyzer utilizes a portable computer equipped with a frame grabber to measure the reflective intensity (gray level) of phosphate samples placed in front of a television camera. P2O5 content is related to the average gray level of the sample, while CaO/P2O5 ratio is determined from the amount of bright material present. The sensor is currently being used to analyze flotation concentrate samples at Texasgulf's phosphate operation near Aurora, North Carolina. Sensor development along with results from laboratory and in-plant testing are discussed.

Jan 1, 1993

By M. A. A. de Klaver

Functional Description Figure 1 is a typical flowsheet for a system for solid fuel addition to filter cake. Solid fuel, coal, coal breeze, or charcoal, is fed from a,stockpile to a surge hopper. The solid fuel is metered into a grinding mill. The fuel is dried and ground in a grinding mill. The on-size particles are removed from the mill by air sweeping. The ground solid fuel is separated from the air stream by a cyclone and stored in a surge hopper. The ground solid fuel is then pneumatically conveyed to a small hopper in the balling area. The fuel is proportioned into the filter cake just prior to mixing. An efficient mixer is very important to have a successful operation. The exact flowsheet would depend on a number of factors including what fuel is used, how the fuel is received, and the cnaracteristics of the fuel as received. Availability of floor space in the plant may also affect the flowsheet. For example, drying air may be supplied from the pellet furnace if the grinding mill can be located near the grate, or the pneumatic conveying system and a surge hopper may be eliminated by placing the grinding mill adjacent .to the mixing area. Also, for a multiple line plant, a ball mill rather than a roller mill may be more suitable.

Jan 1, 1980

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By Jean-Michel M. Rendu

Increasingly, geologists use geostatistical methods to evaluate drilling programs. The complexity of the methods varies with the nature of the available sample information, the objective of the statistical analysis and the geologist's experience. Occasionally, estimating the average sample grade is all that is required. In other instances a semivariogram calculation may be considered. If sufficient data is available, the geologist may wish to estimate blocks or panels of complex shape, using the kriging method of evaluation. Historically, the use of geostatistics by geologists has been limited by a number of factors, most significant being the difficulty in accessing and using computer programs needed to complete the necessary studies. Geologists are often working in remote areas from which electronic communication is unreliable, if not impossible. Even when access to computer programs is technically possible, the costs incurred in accessing and using these programs are often considered prohibitive. In many instances using the programs requires an understanding of computer systems far beyond that which a field geologist can justifiably be interested in acquiring and maintaining.

Jan 1, 1984

By Jerry Williams

GEORGE WEINMAN: At this time, our co-chair, Jamie Davis from Phelps Dodge, will come to the podium. JAMIE DAVIS: Our next speaker is Jerry Williams from Phelps Dodge, Morenci. Jerry is the maintenance planning supervisor and is in charge of preventative maintenance and maintenance scheduling. Jerry's group uses predictive tools to monitor and predict the equipment failure throughout the mine, from pumps to shovels to motors, you name it. The title of Jerry's talk is "If You're Not Using Predictive Tools, You're Behind the Curve." I’ll turn it over to Jerry.

Jan 1, 1998

By Mark E. Gershon

A mixed-integer formulation of the mine scheduling problem is discussed and applied for the purpose of optimizing both the mine production sequencing and the mill blending and processing problems simultaneously. Previous attempts at solving these problems separately, although successful, fail to take into account the interrelationships between these problems. Project structure serves as the outline of this paper, which is directed towards a mining engineering audience. Generalized in its organization, this concept is useful for long, intermediate and short range scheduling. Actual applications are mentioned which show that the concept is also applicable to mining a variety of ores.

Jan 1, 1982

By C. Rodriguez, T. BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle. Blasting is the first and lowest cost per ton stage in the comminution value chain. The basic principle that effective blast design can optimize fragmentation from the Run of Mine (ROM) ore muck pile to improve productivity through digging, loading and crushing to grinding and increase mine site profits has been well documented. Benefits of controlling fragmentation in the blast include reduced wear on equipment, faster loading, increased truck loads while detecting oversize rocks at the muck pile can reduce the frequency of a blocked primary crusher. A second basic principle is a measure of particle size distribution (PSD) at each unit operation in the comminution cycle allows engineers to manage blast design to produce fragmentation in the ROM ore most suitable to optimize downstream unit processes to improve mine site productivity and profits. Split-Online® systems have measured PSD of rocks on conveyors from the primary crusher to the SAG mill for over 20 years. Split-Engineering partnered with various mining companies to develop Split-ShovelCam® to automatically measure fragmentation from shovels and excavators working the ROM muck pile. This paper takes the reader “Back to Basics” by discussing the use of real time fragmentation analysis at the muck pile as an important parameter to optimize energy factors required for each blast. Case studies are given. INTRODUCTION The basics of mining are: • Explore for and find economic resources of valuable minerals • Mine rocks containing valuable minerals using blasting • Crush and grind rocks to liberate valuable minerals (comminution) • Recover valuable minerals for sale Comminution is an energy intensive process which accounts for a major proportion of mine site costs. Effective blasting can improve comminution and deliver significant reductions to mine site unit costs, (CEEC, 2016). Engineers, scientists, builders and even philosophers have long promoted the phrase “measure to manage”; the premise being “you can’t improve what you don’t measure”. Blast Engineers measure fragmentation in ROM ore for feedback to manage energy input in the design of blast patterns to optimize the ROM product size for downstream operations, whether they be for ROM Leach or feed into the primary crusher.

Jan 1, 2019