Search Documents

"Mine ventilation is in every underground mine a crucial process to ensure mine safety as well as acceptable working conditions. On the other hand is also a major cost factor depending on air requirement and air resistance. Due to the fact that the special layout of mines develop over time, ventilation systems change as well. This may result in complex systems which are suffering severe problems and low efficiency. With attention to the mine safety and costs, ventilation systems have to be controlled repeatedly and optimized continuously to fit changing conditions. The project “Improvement of ventilation systems in narrow vein mines” has been commenced with measuring and data collection in the Bogala Mine, Sri Lanka. This over 150 year’s old graphite mine consists of about 20 levels. The resulting ventilation system is highly complex and suffers problems like high temperatures and humidity as well as a mixing of fresh and used air on lower levels. To solve these problems and to optimize the system the complete ventilation system had been measured on-site first. The gained data have been used for simulations to develop and select an optimal and cost efficient solution. OBJECTIVE As an important process in mining ventilation is a major cost factor and can determine the economic feasibility of a mine. Due to the production mine layouts develop over time and mines increase in size and depth while the ventilation system becomes more complex and may suffer severe problems and inefficiency. Therefore mine ventilation systems have to be controlled and optimized regarding the general requirement of mine safety and health of the miners as well as the costs. Depending on the deposit type, depth, mining method, climate and as well corresponding laws and regulations the possible solutions are varying strongly. The work carried out paid special attention to the improvement of ventilation in narrow vein mines in tropical climate, in this case the graphite mine “Bogala” in Sri Lanka, South Asia."

Jan 1, 2015

By Gabriele Eccher, Michele Caponero, Paolo Cucino, Roberto D’Angelis

"This paper describes the optic fiber structural monitoring system implemented for Pavoncelli Bis tunnel. The paper highlights the optic fiber sensors customization capabilities, how they smoothly fit precast concrete lining processes and TBM operations, and how a lifelong service monitoring can be achieved. An overview of readings’ evolution during excavation concludes the paper.INTRODUCTIONPavoncelli Bis is a 10 km hydraulic tunnel designed to by-pass the existing Pavoncelli tunnel which experienced severe damages during the 1980 Irpino-Lucano earthquake, in south of Italy (Barla 2009). Pavoncelli Bis excavation work commenced in 1988-90, however, when excavation approached pk. 0+583 in 1992, water percolations became more and more consistent and resulted in work suspension. The tunnel was eventually sealed at pk. 0+383, leaving a flooded section between pk. 0.383 and pk. 0+583. Work resumed in 2012 where EPB-TBM excavation was adopted to cross the flooded section and to overcome complex hydro-geological conditions in various lito-types and, in particular, in the Varicolori Clay-shales area (Figure 1).Consequently, stress evolution monitoring is extremely important during construction and during the service life of tunnel lining in clay-shales and in faults areas. In particular, the paper focuses on the monitoring system proposed for the newly EPB-TBM excavated portion from pk 0+583 onwards where optic fiber sensing technology was chosen for its reading stability and reliability in presence of water and its ability to be connected in series and remotely interrogated at kilometers of distance. FBGS OPTICAL FIBER SENSOR TECHNOLOGYFiber Bragg Grating Sensors (FBGS) are gaining increasing attention in the field of experimental stress analysis. Basically, Fiber Optic Bragg Sensors are strain-measuring devices and therefore provide many of the advantages of the well-known metal foil strain gages (Kreuzer 2007).Bragg gratings are written into so called single-mode fibers. These fibers consist of a very small inner core of 4 to 9 µm diameter and an outer part (cladding) of pure glass (SiO2) of 125 µm diameter. The difference of refraction indexes between inner core and cladding causes the light to propagate only inside the small core."

Jan 1, 2016

By E. C. Westman, W. R. Thomas, W. J. Conrad, A. J. R. Russell

"Understanding ground control problems continues to remain a focus of the mining engineering community. To aid mine operators and engineers in identifying and responding to ground control issues, the Ground Observation System (GOS) is being developed. The GOS is an integrated, web-based graphical user interface that displays ground response data collected wirelessly from an underground mine. It presents data in an intuitive manner to assist mine personnel, who are on- or off-site, in quickly identifying hazardous areas. Geotechnical instrumentation will be connected to wireless transmitters that will relay data in real-time to a surface computer that stores the information in a database. The GOS website will then display the geotechnical data in graphical and tabular forms, as well as in conditionally formatted mine maps. Data from each measurement device will be able to be viewed in its entirety or within a time interval, and can be downloaded for further analysis. The ability of the GOS to quickly interpret and communicate mine hazards to personnel of varying technical ability should prove to be a useful tool in understanding ground control and thus improving mine safety.INTRODUCTION Computer-based data information centers that convey operating parameters and conditions are prevalent in modern underground mines. Today’s systems are popular in showing ventilation controls and monitoring equipment performance (Jyothi & Meena 2013). In ground control monitoring, Conover, Ross, and Bigby, 2010 have installed a wired telltale roof monitoring system that sends roof displacement data every ten minutes to a computer on the surface. The computer receives, stores, and displays the data in real time. Data can also be viewed remotely through a password protected internet connection. Additionally, an internet connection allowed for remote updates to the system which streamlined software development and maintenance by eliminating travel (Conover et al., 2010). Currently, no such system beyond Conover et al.’s design has been accomplished. The Ground Observation System (GOS) is being developed to fill the void of real-time geotechnical monitoring in underground mines. A wide array of data will be transmitted wirelessly and broadcasted to on- and off-site mine personnel through the internet. The GOS will incorporate geotechnical data from roof deformation, borehole scratch testing, photogrammetry, and seismic monitoring into one interface, all while achieving permissibility for the use in gaseous mines. As a result, a comprehensive view of rock movement due to mining will be available. The overall purpose of the GOS is to deliver warnings; to ensure reliable data is relayed to personnel for the identification of potential ground failures, provide mine engineers information to design more stable mines, and assist with further geotechnical research."

Jan 1, 2015

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed a series of lab tests to evaluate the respirable dust removal capacity of an industrial air-cleaning fan. Limestone and coal dust were tested separately in NIOSH’s full-scale drill table simulator at the Pittsburgh Mining Research Division (PMRD). Gravimetric samplers with Dorr-Oliver Cyclones and 37-mm filters were used at two upstream and four downstream locations inside and outside of the drill shroud chamber. There were six tests performed for both the limestone and coal dust experiments. In the limestone tests, an average respirable dust concentration of 98.86 mg/m3 was achieved upstream of the air-cleaning fan. The filter results show that the averaged respirable limestone dust reductions were 7.84%, 8.81%, 10.94%, and 18.02% at the four sampling locations downstream of the fan. In the coal tests, upstream samplers achieved an average of 129.03 mg/m3 of respirable coal dust. The averaged dust reductions were 9.54%, 9.83%, 18.54%, and 19.21% at the four downstream sampling points. The results indicate limited cost benefits of using this technology because of the relatively low dust reductions determined from this laboratory study.

Feb 1, 2023

By Nasser Madani, SULTAN ABULKHAIR

The geological and geostatistical modeling of mineral deposits requires densely sampled drillholes that provide accurate and reliable hard data. Furthermore, quantifying orebody uncertainty through geostatistical simulation can allow mining engineers to assess long-term risk in mine planning. Nevertheless, ore deposits can sometimes lack dense drillhole information, reliable hard data with proper quality assurance/quality control (QA/QC), or sometimes both. This study is based on a coal mine located in the Republic of Kazakhstan, where an iron dataset is based on data from three newly drilled drillholes, and geological information comes from a massive collection of legacy drillhole data with no evidence of proper QA/QC. For this reason, a workflow was introduced to construct a representative training image from legacy data and stochastically model geological domains within these three drillholes using a multiple-point geostatistics technique. Once the geological model was obtained, a two-point geostatistics algorithm was applied to model the iron inside each geological domain. The direct sampling algorithm was chosen for modeling geological domains, and sequential Gaussian simulation for iron grade calculation. Both methods were extensively evaluated using different statistical tools and analyses.

Aug 1, 2022

By Steve Kral

Through advanced technology and innovative thinking, the mining industry has become one of the world’s leading industries in environmental protection. But it only takes one Summitville, Omai or, most recently, the Aurul gold tailings retreatment operation in Romania to provide ammunition to the industry’s critics in their attempts to sway public opinion against mining. So for the mining industry to continue operating with the public’s support, it must continue to improve its tailings waste-disposal processes and the dams that hold this waste. In January, about 120 specialists in the mine waste management field gathered together to discuss the available technologies and materials for controlling mine waste and mill tailings disposal. “Tailings and Mine Waste’00” was held at Colorado State University in Fort Collins, CO. This meeting, begun in 1978, is a continuing symposium. It provides a forum for environmental professionals to discuss the state-of-the-art in mill tailings and mine-waste disposal methods.

Jan 1, 2000

By E. H. Cho, P. K. Dai

An acid mine drainage sludge sample, containing 3.6% Mn, 0.18% Ni, 0.15% Co and 0.39% Zn, was obtained from central West Virginia. The sample was leached at room temperature with a pH 3 sulfuric acid solution. Air was then bubbled through the leach solution at pH 4.5 to precipitate the iron. The leach solution contained 258 ppm Zn, 105 ppm Ni, 90 ppm Co and 2050 ppm Mn. Three solvent extraction studies were performed to selectively extract these metal ions in a sequential operation with DEHPA. Cyanex 272 and Lix 84. The A/O ratio was one, and the extractants were diluted ten times with kerosene. A study of solvent extraction with DEHPA showed that Zn could be extracted without Ni or Co up to a pH of 2.75. A pH of 2.75 is considered to be the optimum pH to maximize the selective separation of Zn from Mn. The separation factor of Co over manganese suggests that the two metal ions should be extracted together by Cyanex 272. The separation factor of Co over Ni indicates that these two metal ions can be separated most effectively around pH 5.3. Also, Ni can be effectively extracted by Lix 84 above pH 5.5.

Jan 1, 1995

By Gu Guohua, Hu Yuehua, Zhang Qin

The flotation behavior of pyrrhotite was investigated by using ethyl xanthate as a collector. Results showed that pyrrhotite had good floatability from pH 2 to pH 11, and poor floatability when pH was >12. The flotation of pyrrhotite was dependent on pulp potential on various pH values. The potential-pH range for pyrrhotite flotation was established. Cyclic voltammeny and FTIR spectroscopic analysis showed that the major adsorption product of ethyl xanthate on pyrrhotite was dixanthogen. The intensity of FTIR signals of dixanthogen adsorption on pyrrhotite and the anode current of a pyrrhotite electrode and flotation response of pyrrhotite are correlated with pulp potentials.

Jan 1, 2005

By Haydn H. Murray

Kaolin is defined and described as an industrial mineral. In addition the types of deposits -primary and secondary are defined and the genesis of kaolin from feldspars and other minerals discussed. The major deposits of the world found in the United States, Great Britain, Brazil, and Czechoslovakia are described along with many of the minor kaolin deposits. Four areas which have very large deposits of kaolin could, with technological breakthroughs to reduce viscosity significantly, become important factors in supplying the world markets which are increasing year by year.

Jan 1, 1977

By A. Bakalarz, M. Duchnowska

"The copper sulfide ore from the Legnica-Glogow Copper Basin in Poland, which is processed by KGHM Polska Miedz S.A., consists of three lithological fractions: dolomitic, sandstone and shale. The copper ore, depending on the mining area, contains all fractions in different ratios. The lithological fractions differ in the particle-size distributions of their useful minerals. In the dolomitic part of the ore, most of the metal sulfide particles are 50-200 microns in size, while those in the sandstone and carbonaceous shale are 30-200 and 5-40 microns in size, respectively. This complex composition results in different mineralization, physicochemical properties and, in particular, upgrading selectivity. Due to the specific nature of the examined copper ore, two of the crucial parameters determining the beneficiation efficiency are size and liberation of sulfide particles. We analyzed the influence of grain size of feed on scavenging selectivity in one of the KGHM flotation plants and performed evaluation and analysis of the upgrading results of industrial beneficiation of the ore, containing mostly dolomite and shale. The upgrading efficiency was estimated using a selectivity indicator obtained by means of the Fuerstenau upgrading curve, which was then correlated with the particle-size distribution of the flotation feed.IntroductionFroth flotation is used extensively in commercial ore treatment flotation plants to separate minerals from gangue and to separate minerals from each other. The floatability of ores and their benefication selectivity are determined by many factors. One of them is particle size. The effect of particle size on flotation performance has been widely studied by many authors (Gaudin et al., 1931; Trahar, 1976; Trahar and Warren, 1976; Lynch et al., 1981; Pease et al., 2004). Particle size also plays a critical role in the probability of particle collision and attachment to bubbles (Solari and Gochin, 1992; Schulze, 1993), kinetic flotation (Taggart, 1956; Ahmed and Jameson, 1985; Debacher, 2002; Brozek and Mlynarczykowska, 2007; Potulska 2008), collector consumption (Sutherland and Wark, 1955; Vianna et al., 2003) and mechanical entrainment (Lynch et al., 1981; George et al., 2004; Konopacka, 2005). Most of the results have shown that there is an optimum particle size range for a given flotation system and that the simultaneous optimization of the recovery and concentrate grade of these particles in conventional flotation equipment is extremely difficult."

Jan 1, 2015

By Fabrizio Fara

The Ship Canal Water Quality Project (SCWQP) includes a 2.7-mile long, 18'-10" internal diameter tunnel which is located inWest Seattle. Tunneling in urban areas and soft ground conditions (Till and Till-like soils in Seattle) is associated with the risk of settlements, especially in presence of groundwater above the alignment. The Designer foresaw the use of soil improvement (jet grouting) outside of the launch shaft to mitigate the risk of flowing ground and to provide a redundant sealing. The Contractor proposed and ultimately successfully executed a different approach by using a “Steel Bell System” or Pressurized Can as described in this paper.

Jun 13, 2023

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

By Howard N. Egan

EASTERN COAL CORPORATION is located in the heart of the Appalachian Mountain area of extreme Eastern Kentucky, The mountains are of sedimentary origin, and have been deeply eroded by streams as the area has been thrust up during geologic time. There are many seams of coal interspersed between beds of shale and sandstone. While some of the seams are thin, there are a number that can be economically mined. We are mining the Pond Creek, or No. 2 Gas Seam, at a rate in excess of 6,000 tons per day. Our central preparation plant utilizes tromp baths for the plus 3/8" size and Rheolaveur for the minus 3/8" portion. No provision was made to recover the fine coal, which was included with the plant effluent pumped to a 12 acre refuse pond. The pond is impounded behind the coarse refuse dump. This pond rose 15 feet last year. Obviously, no pond could stand many years at this rate. Limited pond space in this rugged area of steep hills and narrow valleys dictated a revised disposal method. Our first thought was that it would be necessary to dry the fine refuse sufficiently to permit inclusion with the coarse refuse, which is hauled uphill by monitor and then trucked to final disposal.

Jan 1, 1967

By Yves Boissonnas, Marco Bettelini

"INTRODUCTION AND OBJECTIVES The operational safety of long and very long rail tunnels represents a key issue in all development stages, including design, construction, commissioning and operation. The spectrum of potential threats is very broad and challenging. These issues can only be mastered by means of a proper combination of a number of safety measures at various levels. This paper focuses on the specific safety issues and the extremely challenging conditions characterizing very long and deep tunnels. They include a significantly increased risk during operation that the incident train cannot exit the tunnel by its own means, long self-rescue and rescue distances, the presence of a number of trains, possibly mixed traffic as well as significant thermal issues. Amberg Engineering is strongly involved in the design and construction of most long and very long rail tunnels in Europe, including in particular the Gotthard Base Tunnel (GBT), Lyon-Turin Base Tunnel (LTF) and the Brenner Base Tunnel (BBT). The combined experience arising from these tunnels forms an invaluable body of expertise, which is summarized in this paper. The focus is on shared issues with practical relevant examples and project-specific solutions. Special attention will be devoted to the 57 km long Gotthard Base Tunnel, which will be operational by mid-2016 and will be the longest infrastructure tunnel worldwide. VERY LONG TUNNELS IN EUROPE Overview From the point of view of safety, tunnels in excess of about 20 km exhibit a significantly increased risk that incident trains could stop within the tunnel. This is related to the European Technical Specifications for Interoperability (TSI) on rolling stock, to be discussed in the chapter on rescue stations. This paper will specifically focus on the following longest tunnels in construction or operation, listed in Table 1."

Jan 1, 2016

By G. Vogt

Water is one of the most important ressources of our planet. Unlike many other natural resources, water cannot be substituted by anything and must therefore be handled with the utmost care. Depending on the region and the possible shortage of water, the importance of water increases even further. Water consumption is not the only factor. In the construction industry, water pollution from auxiliary and operating materials and processes as well as other contaminants and their resulting load on wastewater play an important role. The sources for wastewater on tunneling construction sites are various: Washing water, seepage water accumulating in construction pits, tunnel water, water used in the slurry circuit in fluid-assisted tunneling methods or water from concrete work and stone cutting all these waters are contaminated with a range of pollutants like solids, hydrocarbons, heavy metals, etc. These contaminants can be removed or treated/reduced with the help of specifically designed wastewater treatment plants (WTPs). After the treatment the cleaned water can be either, in best case, reused on the construction site itself or discharged into water utilities like the available sewer or river pin respecting their discharge requirements. Due to dwindling water resources globally, the continuously rising discharge limits and the ever more important aspect of sustainability the use of WTPs on tunneling construction site will be indispensable. In this paper, it will be presented how these systems are designed and work, what advantages they offer environmentally as well as financially and what to look out for when planning and implementing such a system onto jobsite.

Jun 23, 2024

By Michael L. Ogilvie

The proportion of underground coal production as a percentage of overall Australian production has fallen in the last 10 years, with underground production remaining more or less static at about 53 Mt (58 million st). However, underground coal mining remains a viable industry in Australia, due to use of modern longwall mining systems. In 1993-1994, 26 longwalls were in operation, with total production exceeding 39 Mt/a (43 million stpy). Some of these longwalls achieve productivity levels approaching efficient opencut operations, and in some cases, they exceed them. These high-production longwall mines are not without problems when depth and distances from outcrop increase and the gas content of the seams approaches or exceeds critical limits. When gas content of a coal seam exceeds 6 m3/t (233 cu ft/st), gas flows into the mine may be sufficient to interrupt production from time to time.

Jan 1, 1995

By Otto E. Zwanzig

You may think long before this talk has been completed that the speaker is belaboring the obvious. Please let me put to rest here and now any doubt which you may have in this regard by assuring you that is precisely my intent, and for a very specific reason. We all profess to know and recognize the obvious, but I am impressed increasingly how often we forget or fail to act upon the obvious. Shortly after starting my first job upon graduation from college, I was asked by my boss to participate in a course on practical communications, particularly as applied to conveying proposals effectively to the client -- be he customer or company president. The concept or philosophy underlying this program was so simple and obvious that in my youthful brashness I saw only a gross waste by the company of e good, solid $1930 in compelling me to take the course. The sequel to this experience occurred about five yews ago when I was directing a 300-man marketing group. At that time I enrolled a dozen of my department heads, and subsequently about a hundred other personnel, in the contemporary version of that sane program. Why? -- because they all knew the obvious, but I could see how imperfectly they were implementing it. Truly, a wide chasm exists all too often in our beliefs on the one hand and our practices on the other.

Jan 1, 1962

By R. J. Roman

The results of column leaching tests on 3 different mixed oxide/sulfide ores from a Chilean deposit are presented. The 3 samples contained different ratios of oxide copper minerals to chalcocite and chalcopyrite. The results of the column leach tests are interpreted in light of the shrinking core model for coarse particle leaching. The copper recovery from the oxide minerals and the sulfide minerals each conforms to the shrinking core model with the total recovery equal to the weighted average of the individual minerals. The use of column test results to predict field heap leaching results using the multi-mineral shrinking core model is discussed.

Jan 1, 1993