Search Documents

By Chi-shing Wang

In many cases the roof strata of a bedded deposit may be considered as a composite of rock beams of rectangular cross section, whose component layers differ in thickness and may or may not be separable from each other when they are subjected to loading by their own weight. An analytical study of the behavior of such multiple-layer beams is extremely difficult owing to the heterogeneity and anisotropy of rock materials. The complexity is revealed by the fringe photographs obtained from several series of barodynamic photostress experiments conducted on various types of multiple-layer model beams of a medium-grained Bedford limestone. Further discussion on the applicability of barodynamic photostress techniques to the model study of the behavior of mine roofs in stratified geologic media is presented by comparing the phenomenological observations recorded in this investigation.

Jan 1, 1968

By John W. Trammell

The White Pine Mine is situated in Ontonagon County, approximately six miles south of Lake Superior, in the Upper Peninsula of Michigan (Figs. 1 and 2). The ore body mined by White Pine Copper Company occurs in the lower - most 20 to 25 feet of the Nonesuch formation, a series of middle - to upper Keweenawan shales, siltstones, and sandstones. This paper elaborates on the solution of problems in ore grade control and mine planning arising from the presence of an essentially barren sandstone stratum within the ore body.

Jan 1, 1964

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By Soner Top

In this study, a process to separate manganese and iron from manganiferous iron ores by reductive acid leaching followed by magnetic separation was conceived and experimentally tested. In the leaching process, sulfuric acid was used as lixiviant and oxalic acid was used as reductant. The experimental results showed that the manganese and iron separation was optimal when the concentrations of the sulfuric acid and oxalic acid were 0.75 M and 30 g/L, respectively, at a temperature of 80 °C, a solid/liquid ratio of 67 g/L, stirring speed of 400 rpm and leaching duration of 60 min. Under these conditions, 90.49 percent and 6.78 percent of Mn and Fe were dissolved, respectively, from the ore sample in a size fraction of smaller than 106 µm. It was determined that the leaching of manganese from the ores was a second-order reaction with activation energy, Ea, of 53.38 kJ/mol. The leaching residues obtained under the optimal conditions were subjected to wet high-intensity magnetic separation tests to recover the remaining iron content. This separation process produced a concentrate containing 56.20 percent Fe and 1.79 percent Mn with iron and manganese recoveries of 56.83 and 66.73 percent, respectively. To the best of our knowledge, this is the first time that a magnetic separation process was used on a residue obtained from the reductive acid leaching of manganiferous iron ores to recover iron.

By J. Kretschmann

"By the end of the 1950s, the German hard coal mining industry produced 150 million tons of hard coal per year in 170 collieries with 600,000 employees. At that time, 70% of the primary energy demand of the Federal Republic of Germany was covered by domestic coal. However, due to coal mining becoming an increasingly globalized business and the oil and gas industry producing with lower costs, the German domestic hard coal industry stood constantly under restructur-ing pressure. The industry declined until the end of its life cycle. In 2007, a political understanding was arranged to phase out German hard coal mining in a socially acceptable manner by the end of 2018. This decision required a new strategy for the coal mining industry. Being strictly finalized, the German hard coal mining industry has to be prepared for the post-mining era. To create a sustainable development strategy, the long-term impacts of coal mining activities in Germany concerning the environmental, economic and social dimensions will be analyzed systematically and forward-looking. The regional and social responsibility during the closing process and for the post-mining era will be emphasized. High technical standards in environmental protec-tion and post-mining technologies, as well as long term experiences in the development of former mine sites to create new jobs are significant from an international point of view. The traditionally constructive social partnership between employers, union, and employees has enabled long-term stable adaption processes and avoided social friction. The sustainability strategy of the German hard coal mining industry can be regarded as a role model for other mining countries and regions facing similar transition challenges. INTRODUCTION Principally, mining is a finite business that reaches its end if the deposits are depleted or the raw materials can no longer be mined in an economically profitable way. However, the impact of mining is po-tentially an infinite one – at least if you measure it at a human time scale. Mining always means interfering with geological and ecological structures that cannot be reversed to their original condition. In general, the mining cycle (Figure 1) can be divided into three phases: 1. The exploration phase, in which the deposit is investigated to determine its technical and economic profitability. The period of these undertakings is relatively short and can lead to the launch of mining operations. 2. What follows is the actual mining phase which usually lasts for a long time and ends latest when all deposits are fully depleted. This lifespan may be shortened if the economic conditions (production cost or market price) deteriorate. Nevertheless, mining may be resumed if those conditions become favorable once more (examples are silver mining in Germany or rare earths mining in the USA). 3. The longest phase, however, is the post-mining phase as the human interference into geology and nature is usually inten-sive and irreversible. Mining can lead to consequences which have a permanently adverse impact on people and the environment; therefore, they have to be managed as best we can (1)."

Jan 1, 2017

By Robert R. Dorfler

AMPS[. has completed a rationed grinding ball test in a 2.93 m x 2.93 m ball mill at Climax Molybdenum Company. The test consisted of purging the ball distribution formed by charging 100%, 76 mm carbon steel balls with a distribution formed by charging 50% 76 mm and 20% 51 mm alloy steel balls. The resulting change in ball surface area yielded improvements in both tons ground and fineness of grind with a significant reduction in total ball consumption. This paper summarizes preliminary studies leading to the plant test, grinding efficiency results, and future plans to optimize the ball charge.

Jan 1, 1981

By Pierre Filiatreault, Brian Straight, Stephanie Thibeault, Devin Castendyk, Londie Cameron

"Working on or near water at active, closed or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the U.S. Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at U.S. metal, non metal and coal mines (MSHA, 2000). Openpit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including: a) drowning, b) hypothermia, c) falls to the ground from the top of high walls, d) collapse of unstable access roads, e) rock falls and avalanches from pit walls, f) avalanchegenerated tsunamis traveling across the lake surface and g) rapid degassing events.Some pit lakes are simply not safely or easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on a regular basis is needed to monitor the evolution of water quality over time, verify the accuracy of numerical predictions and, ultimately, manage lake water chemistry and ecological risks. For pit lakes with surface water discharge, regular monitoring is used to appropriately design and adjust water treatment plants in order to produce acceptable site discharge water quality.As a product of these risks and the need for water samples, mining companies spend considerable expense on pit lake safety as part of monitoring programs. This includes training personnel for on water duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices and cold-water clothing called mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface and employing spotters who can directly communicate with emergency medical services to watch sampling activities because cell phones and radio signals can be blocked by pit walls. Some sites utilize redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires two boats on the water during pit lake sampling events, with a third boat on the shoreline, gassed and ready to go. In addition, water samplers are required to hold Marine Emergency Duties training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel in the event of an accident."

Jan 7, 2017

By H. M. King

A combination of chemical, statistical, geographic, and microscopic analyses reveal that sulfur in West Virginia coals is extremely variable in both form and abundance. Coals in southern West Virginia typically contain less than 1% total sulfur with organic sulfur being the dominant species. Northern West Virginia coals average about 2% total sulfur, mainly contributed by sulfur minerals. In addition to these regional trends, significant variations in sulfur form and abundance exist both vertically and laterally within individual seams. On both regional and local scales, the pyritic sulfur component can vary significantly in mineralogy, particle shape, maceral association, and particle size.

Jan 1, 1986

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By Jr. Gambrell

For more cost effective strata control, a fundamental understanding of the behavior of the support system is needed. To assist in this understanding for shield supports, behavior of a four-leg shield design used on a soft floor in an operating longwall system is presented. The shield was constructed having a split base and a split caving shield. Attention is focused on other-than-normal loading on the canopy and its effect on deformation of the lemniscate links. Examples of the typical bending and twisting deformations are given. Schematics of the canopy, caving shield, and lemniscates showing important forces and moments are presented. Approximate minimum values of the forces and moments are calculated. The need for use of more inclusive three-dimensional design techniques is demonstrated.

Jan 1, 1990

By A. R. Laplante

A test to determine the amount of gravity recoverable gold (GRG) in an ore is described. Typical GRG results are given; an error analysis is detailed; possible uses are discussed. Of the 38 samples tested, the lowest GRG content was found to be 25% (most below 25 11m, or 600 mesh), and the highest 94% (most above 300 11m, or 50 mesh). The average GRG content was 63%, with a standard deviation of 19%. Error analysis shows the test to be reproducible within 5 to 10%, depending on the size distribution and grade of GRG, and the sample extraction protocol. When using the same primary sample, reproducibility improves, 2 to 5%, depending on the amount of gold coarser than 850 11m (20 mesh) and sample weight. The test has been applied to greenfield project and retrofit applications, to determine the suitability of gravity recovery. For existing circuits, it has been coupled with a model of gravity recovery for optimization studies.

Jan 1, 1996

By William C. Howe

This paper describes the technical status of the atmospheric pressure fluidized bed combustion (AFBC) process for utility steam generation. Major areas where AFBC development work is needed are discussed. Various approaches to solving these key issues are identified and the ongoing research and development programs addressing the key development areas are described. Other significant programs pertaining to the development of AFBC for utility steam generation are also discussed and needs for future work identified.

Jan 1, 1978

By E. J. Karges

[For reasons well known to Mining Engineers, fine grinding in the wet form is quite universal inn plants engaged in the traction of metallic values from crude ore In the processing, of non-metallic and industrial minerals, however, fine grinding in dry form is the more common method. The crude materials generally contain less moisture than required for wet grinding, and the products are usually marketed or used in the dry form, most of them as powders. To grind wet would therefore entail the addition of water and the expense for drying the product, which is not justified. This paper will concentrate on the particle size reduction or fine grinding of materials to produce a dry powder]

Jan 1, 1963

By R. Venugopal, V. K. Saxena, Veerendra Singh

"Ore morphology plays a vital role during the milling and liberation of minerals. This study was carried out to understand the role of mineral crystallography and mineral interfaces on the milling and liberation processes. Data related to mineral crystallography, Vickers Hardness Number and beneficiation processes were collected from literature, and detailed statistical analysis was conducted to relate these parameters. Review of the crystallographic information of minerals present in ores indicates that molecular weight and cell parameters significantly affect milling and liberation characteristics. Mineral interfaces were classified into the three categories of coherent crystals, semi-coherent and incoherent crystals, and breakage behaviors were studied. The studied cases revealed that these material interfaces control the micropore properties that play a vital role in the initiation of intergranular and intercrystalline fractures which occur in siliceous manganese ores and dolomite as a result of thermal treatment. In contrast, banded hematite jasper and coal exhibited a much more complex fracture pattern due to their coherent interfaces and finer physical associations. This study explains the effect of the various types of interfaces on milling, and the approach can be helpful in developing a methodology to enhance mineral liberation with minimum energy consumption.IntroductionComminution is a vital unit operation in the mineralprocessing, cement-making, power-generation and pharmaceutical industries. Its importance in mineral beneficiation operations is increasing every year as a result of the growing need to exploit lower-grade ore bodies and process reject materials (Blazy et al., 1994; DOE, 2005). Low-grade ores require significant energy during grinding to liberate the valuable minerals, which are further separated from the gangues by various beneficiation methods. Various attempts have been made to enhance mineral liberation during grinding to minimize energy consumption. Most of these studies focused on the analyses of the compression mechanism, chemical additives, thermal treatment, microwave treatment and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman et al., 1997; Kumar et al., 2010; Wang et al., 2011; Singh et al., 2012). However, many of these efforts had limited success, and there is a need to see the problem from a fresh perspective."

Jan 1, 2015

By Conrad W. Steller

What is the definition of a successful construction or development project? It could be described in many ways: a project that performs as designed; a project completed on time, a project completed within budget. The title of our talk today is, "The Advantages of Applying Design/Build -Construction Management to the Mining Industry." As our talk develops, you will see that rather than tell you how to apply this concept, we will discuss the advantages and details of Design/Build so that you can independently apply the concept. Design/Build is not new, and it cannot be universally applied. It has, however, within the past ten years, carved a specific and substantial place in the overall construction -development market. The reasons for its rather recent rise to considerable prominence as a concept is due, in part, to the increasing urgency of gaining productive access of a production facility and, in part, to the inherent advantages of the concept's economics--and they are considerable. If the Design/Build concept of contracting were fully understood, it would, without exception, be the favored way for private industry to contract for its new construction and development as well as renovation work. The basic advantages are: earliest possible access and completion at the lowest cost. Design/Build is often equated and compared to "fast track" or "turnkey" methods of construction. The Design/Build concept can, in fact, be both of these or neither. "Fast track", in and 6f itself, implies that the project will be phased construction, that is to say, it will be built quickly; whereas I "turnkey" is a measure of the completeness of the project, usually meaning essentially that the

Jan 1, 1977

By K. J. Bruxvoort

Background ground water quality is often used to drive remediation programs at sites with waters affected by mining activities. In the past these levels were sometimes chosen without rigorous statistical and geochemical analysis. A probability distribution approach was used at the Sweetwater Uranium Project to separate a large set of geochemical data into populations that represent contributions from different sources. Natural background populations were identified for major ions, metals, and radionuclides, and were submitted to the Nuclear Regulatory Commission to modify the extent of a Corrective Action Program and to establish control limits for future monitoring.

Jan 1, 1998

By S. E. Valji

Clay slurries are normally dewatered using flocculents like sulfuric acid or aluminum sulfate. This type of flocculation is based on the electrolytic mechanism. For certain clay dewatering applications, this method of flocculation is unsatisfactory. Flocculation, based on the bridging mechanism, using organic polymers has been utilized to overcome such problem situations. This method of flocculation offers solutions not possible by previous methods. Normally these flocculents are used to assist dewatering. In this case, not only is dewatering promoted, but also further processing is assisted by a change in the dilatant character of the filter cake that is formed. Discharge of filter cake is easier, extrusion of filter cake on to conveyor dryer is possible or improved, and heat transfer and drying rates of the extruded filter cake are substantially higher. Both natural and synthetic organic polymers have been utilized for this purpose. Selection, application techniques, and economics are described.

Jan 1, 1965

By Jay F. Colinet

Coal workers’ pneumoconiosis (CWP), commonly known as black lung, is caused by the inhalation of respirable coal mine dust and is a disabling and potentially fatal lung disease with no cure. Historically, CWP has taken a tremendous human and financial toll on the U.S. coal mining industry. Recent health surveillance data indicate that CWP continues to occur at elevated levels. Respirable coal dust exposure must be controlled to prevent the development of CWP. The Pittsburgh Mining Research Division of the U.S. National Institute for Occupational Safety and Health (NIOSH) conducts laboratory and mine-site research to identify control technologies that can be used to successfully reduce respirable dust levels. Various technologies, using multiple methods of control, can be applied to reduce dust levels. An overview of CWP’s impact and a general methodology for controlling respirable dust in underground coal mines are discussed in this paper.

By José Ricardo Lopes, Alaor Coelho, Marco Gomes, Alfredo Dacio Moraes Filho, Akira Koshima

"Very low strength alluvial peat soil was found under two old drainage galleries with just 4.3m cover above a twin tunnel due to be excavated by a 10.6m diameter EPB Shield for São Paulo Metro’s Line 5. Alignment was required to strengthen soil and drive the TBM through safely without damaging the galleries. The design included six levels of self-drilling forepoling with lengths up to 15m, using 100 mm-diameter SCH160 metal tubing and injection bulbs with estimated 0.20m diameter. Two 6m-diameter circular shafts were excavated along the shield-tunnel axis, one each side of the galleries, and forepoling fanned out under gallery foundations. Given the peculiar soil and confined working space, more data were needed for correct drilling geometry. Ground mass treatment was successfully designed and executed and galleries were fitted with instruments to enable the shield’s advance. DESCRIPTION São Paulo Metro’s Line 5 (aka Lilas or purple line) is adding 11 stations along an 11.5km extension and three EPB TBMs are being used simultaneously (three EPBs on the same job for the first time in Brazil) with one of them excavating a large cross- section twin-track tunnel. Currently the largest work-in-progress for São Paulo Metro, this project has been divided into seven lots and 9km are already operational. This study refers to Lot 6 where the 10.6m - diameter EPB shield excavation is only 4.3m below two galleries running through a 10m layer of very soft peat soil in an old alluvial riverside region ringed by major roads. After recent filling, this area (Parque das Bicicletas) was used for recreation, although temporarily it has become a construction site. This paper will describe the original basic design; precautions in relation to the structural condition of the galleries after inspection; the problem of absence of data for their foundations; subsoil bore tests; evolution of the engineering design for the galleries and conditioning and reinforcing the soft soil below the galleries to ensure safe advance of the EPB shield, and finally the successful outcome of the solution used."

Jan 1, 2016

By J. A. Lepinski

The FASTMETSM Process is a coal-based process for converting iron oxide fines into metallic iron. The end product, direct reduced iron (DRI) is used as a low residual charge material in electric arc furnace steelmaking. This paper describes the FASTMET Process and its potential application in the United States. Operating results from a 175 kg/h process simulator are presented. Characteristics of the end product are discussed. Process economics are reviewed along with plans for scaling-up the process to full commercial size.

Jan 1, 1993