Search Documents

By A. Yehia

Fluoride activation has been evaluated by Hallimond-tube flotation of collophanite in terms of fluoride concentration, conditioning time, pH, and temperature. The results reveal that efficient oleate flotation of collophanite can be achieved by fluoride activation. Fluoride adsorption by collophanite as a function of fluoride concentration, temperature, pH, and crystal structure suggests that, at low fluoride concentration, a fluoroapatite-type compound may form on the collophanite surface by chemisorption of fluoride ions at calcium sites; at high fluoride concentration, calcium fluoride ap¬pears to form at the collophanite surface invovling a surface-precipitation phenomenon. The formation of CaF2 on the surface of fluoride-treated collophanite is further substantiated by the FTIR spectroscopic measurements, which clearly shows a metathetic exchange with phosphate from the collophanite lattice during surface precipitation process.

Jan 1, 1986

By Thomas R. Kuesel

Just south of the L'Enfant Station in Seventh Street, the WMATA system splits into two branches, each comprising twin single-track soft ground tunnels. Immediately at the beginning of the section, Interstate Route 95 crosses transversely over the alignment in open cut, removing most of the cover over the tunnels. Seventh Street spans I-95 on a bridge whose abutments and pier also cross transversely over the four tunnels, with their footings as little as 7 feet above the tunnel crown (Figure 1). Soil investigations revealed that the tunnels would have to be driven through mixed face, with a clay invert and a waterlogged sand crown. Thus, there was a good chance that the roof would fall in, leaving 1-95 and the Seventh Street Bridge in a crater. Since there was no roof that could be counted on, these were figuratively (and potentially truly) Washington Metro's Topless Tunnels (Figures 2 and 3). DESIGN ALTERNATIVES Faced with this situation, the designers considered several options, including temporary detours that would permit demolition of the bridge and building tunnels under the 1-95 Freeway by cut-and-cover methods. They also investigated structural underpinning of the bridge and freeway pavement, and strengthening the bridge abutments and center pier by post-tensioning to enable them to span over any subsidence trough.

Jan 1, 1976

By Frank Ruskey

Many problem associated with potential hazards in a proposed mining area may not be adequately appraised because of the complexity of trying to evaluate them in terms of production requirements. Frequently, encountered hazards have to be dealt with by day-to-day operational schemes that require the miner to either force a way through them or avoid them by blocking off the area in which the hazards are known to exist. These considerations, after the mine is in full production, can be costly to the mine operator and can increase the danger to the miners. A hazard-evasion computer program for mine planning that will appraise proposed mine layouts on the basis of existing or potential hazards has therefore been developed. The program is intended for use during the planning phase of a mine, where it should assist the mining engineer in making decisions in mine design. With the output from this program, the mining engineer should be able either to corroborate his judgments made on the basis of mining experience or to find unanticipated solutions to design problem. The program tests hundreds of possible solutions to a mining layout, and by sorting out the 10 best (based on a criteria of minimum-abandoned-coal) limits the number of choices that need to be considered and appraised for applicability to a given mine scheme.

Jan 1, 1973

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984

By O. J. Malacarne

The use of a series of thickeners for-washing of the slime fraction of a leached ore is not uncommon in the uranium industry; however, few ore processing mills have used a thickener circuit for washing leached total ore. The, common, practice is to wash the sand fraction in classifiers and, the slime fraction only in thickeners. At the Uravan mill of Union Carbide Nuclear, Company, a total ore' acid leach is employed to extract uranium values from sandstone ores. These leached ores are then washed at a nominal rate of from 1,000 to 1,300 tons per day in a series of washing thickeners. A typical screen. analysis of the ore being washed in these thickeners, is 25 percent -200 mesh, 3 percent +35 mesh and about, one' percent +l4 mesh., The amount of slimes (-200 mesh) will vary from 20 to 30 percent s the mill receives ore from 150 different mines The washing liquor is acidic, from a pH of about 2 in the first thickener to 0.6 pH in the last thickener and of course ally acid duty equipment must be used. The Uravan mill of Union Carbide Nuclear Company is located in Montrose County, Colorado and is physically located on a canyon wall along the San Miguel river. The thickeners referred to in this, paper are located on top of the mesa above the canyon. For purposes of identification, these thickeners are numbered 1 through 8 from south to north.

Jan 1, 1962

By R. J. Sweigard

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. An investigation was conducted of current mined-land planning practices to aid in the development of a procedure for evaluating postmining land use potentials. This investigation considered both the industry and public planning approach to mined-land planning and was based primarily upon three case studies conducted in various regions of the United States. The site planning process that was developed during the investigation is iterative in nature and has been designed specifically for the mining industry. It centers around preliminary studies and data collection, development of land use alternatives, and the evaluation of alternatives. Use of this process facilitates the evaluation of economic, environ- mental, and social impacts of postmining land use alternatives. In this paper, the process is presented along with a description of its development, application, and significance.

Jan 1, 1984

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By W. C. Dailey

The Groveland Mine. Concentrator and Pellet Plant are located in Dickinson County in the Upper Peninsula of Michigan. The construction of the Groveland Mine in 1959 was the first United States operation for the Hanna Mining Company in mining and beneficiating low grade iron formations. (1) The plant produced concentrates at 675,000 lt/yr. (746,600 mt/yr.) which was used as sinter feed in the steel industry from 1959 to 1963. Upon completion of a pelletizing plant in April, 1963 production increased to 1.6 million lt/yr (1.77 million mt/yr) of pellets. After the plant expansion, mill capacity increased to 2.2 million 1t/yr (2.43 million mt/yr.), producing 2.0 million It/yr (2.23. million mt/yr.) of pellets assaying 63.0% iron and 7.0% silica. (1) Prior to April, 1971 the concentrator operated with a flowsheet consisting of spirals and a petroleum sultonate iron notation circuit. This was presented in a paper by R. R. Smith and E. E. Sougstad, "Flotation at the Groveland Mine" in the 50th Anniversary Volume entitled "Froth Flotation". The ore body at the Groveland Mine consists basically of two types of iron formation (34% total iron, 20% magnetic iron head), the most abundant of which is a bedded magnetite-chert-silicate rock. This is intermingled to varying degrees with non-bedded to poorly bedded hematite-clastic quartz-chert rock. (1) In developing the Groveland flowsheet, Humphrey spirals were used because of their ability to produce a coarse size concentrate at a low cost. Tests run in the lab and pilot plant on the Groveland ore showed a. spiral weight recovery in the 27 to 33% range. (2) However as the ore body was opened up, it became evident that the most abundant ore type did not liberate at the coarse size fraction needed for spirals. Plant recoveries for the first five years operating the spirals only averaged from 10 to 15% weight recovery. In 1971 the weight recovery on the spirals had dropped to a low of 5%. To increase iron recovery and at the same time increase plant capacity with the least effect on the present operations the mill flaw-sheet proceeded from a spiral-notation circuit to an all flotation circuit to a magnetic separator-flotation circuit. During this changeover the concentrate grade also had to be improved to meet market demands. To do this the following changes evolved

Jan 1, 1978

By S. R. Maynard

The Ortiz Mountains lie 25 mi (40 km) northeast of Albuquerque, New Mexico in Santa Fe County (Figure 1). Approximately 350,000 ounces (11,000 kgs) of gold have been produced from the Ortiz Mountains since the 1820s. The 100 square mile (260 square km) Ortiz Mine Grant was secured from the Mexican government in 1833 by Jose Francisco Ortiz for the purpose of mining gold. The Grant has remained more or less intact to the present. The mineral rights are currently owned by Ortiz Mines, Inc. of Joplin, Missouri and are leased to LAC Minerals, USA, Inc. (west half) and to Gold Fields Mining Corporation (east half).

Jan 1, 1989

By Yoginder P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15 percent to a maximum depth of 150 feet. The pit orientations along the dip (dipline), strike (strikeline) and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas, and also to furnish a data base-for the computer simulation models. A dragline micro- simulation model (Fluor), a shovel/truck simulation model and a cost analysis model were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and angle of dip. The productivity (Cu.yds/hour) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity larger size trucks were preferable to smaller size trucks in the pit configuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip.

Jan 1, 1984

By David Kwietnewski

Roadheaders are gaining widespread acceptance in North America as a means for mechanical tunnel excavation. Until recently, almost all of the large-scale North American tunnel projects were excavated one of two ways ? the tried and true drill-and-blast method or with the use of tunnel boring machines (TBM), the hi-tech super-excavators. TBMs enjoyed fast-growing popularity worldwide as TBM manufacturers offered greater technology to meet the demand of the civil tunnel industry in the late 20th century. Recently, though, more tunnel projects, large and small, can thank the brute force of a roadheader for getting the job done.

Jan 1, 2011

By Mahmut Altiner

In the present study, the use of horse residue as an alternative reducing agent in the roasting of a low-grade goethite ore containing 17.60% Fe was investigated. Additional roasting experiments were carried out with corn starch and without reducing agent for comparison. Each roasted product was characterized using X-ray diffraction (XRD) and magnetic hysteresis (MH) loops analyses. The optimum roasting conditions (roasting temperature [400, 500, and 600 °C], reducing agent/ore ratio [0.04, 0.08, and 0.12], and roasting time [10, 20, and 30 min]) were investigated based on the Taguchi approach. The magnetic susceptibilities of the roasted sample with the addition of reducing agents were higher compared to that of the roasted sample in the absence of reducing agent. Experimental findings indicate that the horse residue can be used as the reducing agent. Finally, an iron ore concentrate assaying a Fe grade of 62.12% with a recovery of 56.93% was prepared using wet magnetic separation at a magnetic intensity of 0.5 T from the ore roasted under the following roasting conditions: roasting temperature of 500 °C, reducing agent/ sample ratio of 0.08, and roasting time of 30 min.

Jun 3, 2020

By C. A. Carroll

In February of 1989 the Mission Complex of ASARCO Incorporated completed an expansion of its concentrator, raising the base mining rate from 25,900 TPO (28,500 STPD) to 37,200 TPO (41,000 STPD). The expansion was accomplished by extending the twelve existing Mission ball mills in length, by installing the grinding circuit from Asarco's idled Sacaton Concentrator along with various auxiliary equipment, and by modifications to the flotation circuit and water systems. This paper will give a brief history of the consolidation of the ore body which made the expansion possible and explain the various parts of the expansion.

Jan 1, 1990

By Marc. A. Meyers

The analysis of the phenomena involved in the determination of the compressive strength of iron-ore agglomerates leads to the identification of the important parameters. It is shown mathematically that the pellet rupture strength is proportional to the cross-sectional area. Fracture is initiated at the center of the pellets by the tensile stresses developed by the compressive loads normally to the compression axis. The variation in strength between individual pellets of identical composition and subjected to identical treatments is due to internal voids of varying sizes, that act as stress-concentration sites. Two novel testing procedures are proposed. The first consists of testing the pellets between two plates having three steel spheres each. This configuration simulates much better the environment actually encountered by the pellets. The second procedure consists of a thick-walled cylinder in which a piston penetrates; a large group of pellets is tested simultaneously, as the stress versus strain plot is being recorded. This latter test presents significant advantages over the conventional testing procedure; the main one is that one single test is sufficient to characterize the mechanical response of the pellets.

Jan 1, 1981

By Peter N. Blakey

The Kidd Creek orebody is a massive, base metal deposit with widths up to 600 feet and a strike length of 2,200 feet. The orebody dips eastwards at 70° to 80° and is amenable to sub-level open stoping. Five distinct zones (Fig.1) based on structural wall rocks and ore type parameters occur within the orebody. These zones are: Zone 1 - Mainly copper stringer ore Zone 2 - Massive pyrite ore Zone 3 - Massive sphalerite and chalcopyrite Zones 4 and 5 - Are banded and variable in nature Compressive strengths vary from zone to zone with an average of 22,000 p.s.i. and highs of 40,000 p.s.i. The mine is developed from a ramp extending from surface to the 1600 foot level and a 24 foot diameter, 3050 foot vertical shaft with main levels at 400 foot intervals. Sub-levels at 100 foot vertical intervals are driven from the ramp. transverse and longitudinal pillars to support the crown pillar left under the open pit. The layout allows an opportunity to enlarge or reduce pillar sizes and also to introduce fill on any horizon should conditions warrant. It also offers a large number of operating stopes spread through the various ore zones giving good ore blending characteristics. All ore from the stopes is handled through drawpoints using Wagner ST8 scooptrams with an average one way haul length of 650 feet.

Jan 1, 1976

By S. C. Termes

This paper discusses recent Federal Bureau of Mines research on the selective flocculation of various minerals with insoluble crosslinked starch xanthate (ISX). ISX is insoluble, has a shelf life of over a year when kept cold, and has a higher molecular weight due to cross linking than the soluble noncrosslinked starch xanthate used in previous flocculation studies on nonsulfide minerals. ISX readily flocculates a number of sulfide mineral fines but not silicious gangue. Floc formation, floc size, and settling rate are strongly dependent on pH, with the pH dependence differing for each mineral. Bornite has been selectively flocculated from bornite-quartz mixtures, and the bornite-containing flocs were separated from the unflocculated quartz using decantation and washing procedures.

Jan 1, 1982

By A. Roper

Since the Toronto conference in May 2002, the International Council on Mining and Minerals (ICMM) has made progress on the road to sustainability. Fifteen of the world?s largest mining and metal producing companies and twenty-five associations have made a long term commitment to ICMM to improve the environmental and social sustainability of their activities. Sir Robert Wilson (Rio Tinto) assumed the chairmanship of ICMM in October 2002. By December 2002, the Council had approved a Strategic Vision and an operating plan for 2003. Both have been posted on the ICMM website (www.icmm.com). ICMM?s Operating Plan sets out three priority tasks: - Providing strategic leadership to achieve improved sustainable development performance in the mining, minerals and metals industry. - Contributing to international policy discussions on cross-cutting issues of importance to the industry, in collaboration with national and commodity associations. - Promoting dialogue and partnership with other organizations to catalyze sector?wide sustainability initiatives.

Jan 1, 2003

By J. Pancher

"Stainless steel castings are used in abundance in the mineral processing industry. In rotary kiln-based processes, these castings are typically exposed to high loads, corrosive elements, mechanical abrasion and cyclical temperature exposure. In the processing of iron ore pellets, it is typical to use a traveling grate preheater or a straight grate furnace to heat the pellets. Both machines have a conveyor that is mainly comprised of high temperature stainless steel castings. It is these castings which are the focus of this study. The expected life of these castings can be quite short, their cost quite high and the effort to replace them very labor intensive. The goal of this study was to gain a better understanding of the failure modes of these castings. With that basic understanding, modifications to the alloy content could be made to achieve a new operational paradigm. That paradigm could be a cheaper casting, a longer lasting casting or a casting tailored to special operating conditions (for example, highly corrosive gases or sudden temperature shocks). Over the past 4 years, Metso Minerals has sought to achieve a better understanding of the failure modes through modeling, laboratory testing and sampling of used castings from various end-users. In addition, we have tested new alloys in a laboratory setting and also in the field to see how they would perform compared to the existing ""standard casting"". Our testing has revealed interesting data concerning the impact toughness, sigma phase content and formation, chloride attack and other performance attributes of various grades of stainless steel when exposed to cyclical temperatures. Interesting results were also obtained concerning the addition of rare earth elements (Niobium, Boron, etc), nitrogen and manganese to a typical ASTM A297 grade of stainless steel. To date, a few hundred test castings have been installed in iron ore pellet plants worldwide. Many of these test castings have already experienced a year or more of operation with good results.INTRODUCTION Cast stainless steels (ASTM A297 and similar) are a main constituent used in the construction of iron ore pelletizing equipment. A typical straight grate pelletizing machine would contain upwards of 160,000lbs of ASTM A297 Grade HH castings. With a typical casting lasting only two to four years, and a casting costing around $35USD, it is easy to see that the castings are a main contributor to the overall cost of producing the pellets. Grade HH and HI (see chemical composition listed below) became the “go to” materials in the 1960’s and very few changes have been made to this day (the exception being plants that switched to flux pellet production in the 1980’s)."

Jan 1, 2015

By Robert L. Runkel, D. Kirk Nordstrom, James W. Ball

Low-flow reactive-transport processes in Wightman Fork downstream of the Summitville Mine, south-central Colorado were simulated using the OTIS and OTEQ solute-transport models. The simulation was calibrated using data from a synoptic study conducted during October, 1998. Discharge over the 8-km reach from just below the mine site to the Alamosa River confluence ranged from 0.077 to 0.17 m3/s; travel time was 10.7 hours; pH ranged from 4.6 to 5.7. Simulations revealed that mass balance for SO4 was maintained, and that pH, Fe, and Al were non-conservative. Simulations allowing hydrous ferric and aluminum oxide or hydroxysulfate precipitation matched observed water quality conditions more closely than simulations without precipitation.

Jan 1, 2000

By J. R. Batista, J. C. Young

Leachates from gold heap-leaching mines may contain selenium concentrations as high as 2 mg/L. Previous studies report satisfactory selenium adsorption by activated alumina from relatively "clean" drinking waters. However, the findings of these studies cannot be directly applied to the treatment of mine leachate where other ions compete for the alumina adsorption sites. This study evaluated the adsorption of selenium from a mine leachate to develop design parameters for a full-scale activated alumina process. The study revealed that 68% of the selenium in the leachate could be removed by alumina at pH levels greater than 5.0. At pH levels less than 4, silica was poorly adsorbed by alumina, and selenium adsorption was improved. Silica adversely affected the selenium adsorption capacity.

Jan 1, 1998