Search Documents

By Ross Glanville

The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR cam also be expressed as the Optimum Mime Life (OML) in years since the expected mime life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mime life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mime life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low¬-tonnage mines (such as many underground gold/silver deposits) often lead to sub¬optimal results. In fact, am apparently uneconomic deposit at am arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mime' properties based on arbitrary production rates.

Jan 1, 1984

By J. R. Mackie

Reserve Mining Company, the first large-scale taconite pellet producer in the United States, mines it's crude ore at the Peter Mitchell Mire located on the eastern end of the Mesabi Iron Range near Babbitt, MN. The ore is processed at Reserve's beneficiation plant on the north shore of lake Superior at Silver Bay, M. The mine and plant are linked by a 47 mile, double track, railroad which is owned and operated by Reserve. (see Fig 1). At rated capacity, the mine can produce 33 million It/yr of crude ore, 15 million It/yr of waste rock and 1.0 - 1.4 million yd3/yr of glacial till stripping. Haulage of all mined material is accomplished using trucks. Ore is transported by tractor-trailer side dump units which have capacitys ranging from 83 to 110 long tons. Waste rock and glacial till is transported in end dump units of 50 to 120 LT capacity. Loading is accomplished by 11/13 yd3 power shovels and 7/10 yd3 front-end loaders.

Jan 1, 1985

By T. D. Wheelock

The effect of various flotation depressants and surface treatments on the floatability of coal derived pyrites in the presence of XIBC was investigated with a modified Hallimond tube microflotation cell. The floatability of pyrite particles which had been cleaned with hot dilute (5%) hydrochloric acid was relatively large. However, the floatability of such particles was reduced greatly by the addition of specific depressants such as calcium hydroxide and also by treating the pyrite with an aerated warm alkaline solution. Although this treatment and these depressants also had some effect on the floatability of coal particles, the effect was much less than on the pyrite particles.

Jan 1, 1979

By Richard Klimpel

The influence of selective chemical dispersants on the hydrocycloning of a copper ore slurry is illustrated. In the % solids and slurry feed rate ranges associated with industrial practice, desirable changes in both d50 and Sharpness Index values of classification were measured with the use of chemical as compared to tests with no chemical usage.

Jan 1, 1981

WELCOME to the world-class Cripple Creek district where gold exploration and production continue 95 years after the initial discovery. More than 21 million troy ounces of gold have been recovered, valued at greater than $7.8 billion using today's gold price ($371/oz). The Cripple Creek district is localized within and around the margins of a silica-undersaturated alkalic diatreme-intrusive complex. The diatreme appears to be comprised of three sub-basins: 1) a sub-basin east of the Cresson (Fig. 1); 2) a southwestern sub-basin between Victor and Cripple Creek; and 3) a northwestern sub¬basin within which the Globe Hill and Ironclad pits (Fig. 1) are located. The recognition of three separate basins was made by G. F. Loughlin and A. H. Koschmann (1935, Fig. 8) who prepared a contour map on the floor and walls of the composite Cripple Creek basin. The northwestern and southwestern sub-basins are apparent due to the discontinuous exposures of a partially exhumed ridge of Precambrian rocks (Fig. 1). The separation of the eastern and southwestern sub-basins was recognized in mine exposures where a fault-bounded ridge line extends from the vicinity of the Ajax mine toward the Precambrian "island" (Fig. 1).

Jan 1, 1986

By Vas Choudhry

The eighties are likely to witness the first commercial-size coal-to-gasoline plant(s) in the U.S., although uncertainty regarding crude prices and cautious involvement of the Federal Government in the synfuels development are evident. The formation of The U.S. Synthetic Fuels Corporation with passage of the Energy Security Act is projected to pave the way for some of the projects on a moderate scale. The corporate objectives (1) are to provide funds for supporting a number of feasibility studies and loan guarantees for the construction of at least some commercial-size plants and the possibility of product price supports or purchase commitments. There are a number of coal conversion processes (2) currently under evaluation for producing either gaseous or liquid plus gaseous fuels, the other processes such as SRC I are for producing desulfurized deashed clean solid fuel for commercial use.

Jan 1, 1982

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By Edmond F. Lawrence

The Calico area lies within the Walker Lane fault zone, six miles north of Schurz, Nevada. The mineralized area is overlain by a thick section of Tertiary tuffs and ash-flows, that have been intruded by a series of andesite plug, dikes, and sills. The pre-Tertiary rocks outcrops only in two areas at one to two miles distance from the drilling areas. Underlying the volcanics are sediments ranging from siltstones, sandstone, calcareous shales, to carbonates of the Luning sequence. These have been intruded by one or more phaneritic intrusives ranging in composition from quartz diorite to quartz monzonite, with the development of a skarn zone on the south flank that contains extensive mineralization consisting of magnetite, pyrrhotite, pyrite, and chalcopytite, with traces of sphalerite, galena, and molybdenite. The magnetite, pyrrhotite, and part of the pyrite appears to be contemporaneous with the skarn, while, part of the chalcopyrite, galena, sphalerite, molybdenite, quartz, and calcite, occurs as minute veinlets cutting the other minerals. This later mineralization may be associated with a late stage of the same sequence, or possibly associated with another intrusive to the southwest. Geophysical work has consisted of aerial magnetics, ground magnetics, gravity, seismic, and induced polarization surveys. Preliminary induced polarization surveys indicated anomalies at depth, both over the magnetic anomaly and to the northwest. Subsequent IP work confirmed this earlier anomaly, and drilling disclosed extensive mineralization at depths of 400 feet on the northwest end and over 1,000 feet to the southeast.

Jan 1, 1967

By C. E. "Sam" Lovewell

In approaching a discussion of production of cement, I hope I won't be like the porter in the bank who was asked if he could give some details on the rediscount rate. He replied, "Boss, when I said hello, I told you all I know." Need for change every so often is illustrated by the story of the little boy four years old who had not spoken a word in those four years. One morning he said, "This damned oat meal is burned'." His Dad was amazed and said, "Son, how come you haven't said a word for four years and now out of a clear, blue sky you say, "The oat meal is burned." Johnny said, "Well, up to now everything has been all right." Not being a mining engineer myself, and my subject not dealing with mining engineering directly, I can only hope that you will agree that the subject has current relevancy by the feet that it can materially improve our environment by putting to good use a potential environmental polluter; namely, fly ash. The profitable utilization of fly ash can reduce cost of use of coal as an energy source. Therefore, it behooves us all to explore to the greatest depth, the pluses and minuses occasioned by its use wherever possible. My particular subject and my particular interest lie in its utilization as a blend in the production of Type IP Portland-Pozzolan Cement meeting requirements of ASTM C-595, Type IP.

Jan 1, 1974

By William H. Peterson

How is the Government's oil import control program doing? In July 1954 Mr, Eisenhower established the Cabinet Committee on Energy Supplies and Resources Policy. On July 29, 1957, the Administration imposed "voluntary" company oil import quotas on American oil importers to maintain "a healthy domestic (oil) production industry" and safeguard "national security." On March 10, 1959 the President by proclamation made the voluntary program mandatory. But study of the program in practice shows that it is not working out as expected and-that there is some doubt that its aims and other related Administration purposes are being achieved. Take the Administration's anti-inflation policy. To be sure, the President apparently recognized in his March 10th proclamation that in restricting cheap imported oil in favor of more expensive-domestic oil he was making the inflation fight that much harder, for he called for Government surveillance of domestic oil prices to prevent them from getting out of hard, And indeed while domestic crude oil prices have not risen appreciably during 1959 neither have they fallen appreciably (although there has been some price weakness in the past few weeks).

Jan 1, 1960

By T. Y. Yan

The various ion exchange reactions occurring during the restoration of formations contaminated with ammonia during in situ uranium leaching are reviewed. Data are presented on the restoration of a previously leached laboratory packed column using line saturated brine. Although this restoration fluid selectively and effectively removed the ammonia, 24.5 pore volumes are required to reduce the ammonia concentration from 500 to 3 ppm. The presence of NaCl in the restoration fluid is beneficial in + improving the selectivity of the system for NH removal and reducing ca++ ion consumption.

Jan 1, 1982

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

High-quality sample selection for metallurgical test work is essential to a geometallurgy study, but the large multidimensional dataset makes sample selection a daunting task, as classifying the dataset while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, utilizing custom-built tools in Python to standardize the methodology, saving time and costs. This approach uses the cumulative sum method, principal component analysis, and k-means clustering method to elegantly cluster the data and select representative samples. A case study is used to demonstrate the effectiveness of the methodology by selecting 40 samples for flotation test work.

Feb 1, 2024

By Ernest E. Thurlow

"Western Coal" in this paper is limited to those deposits of subbituminous coal and lignite in the States of Montana, Wyoming, and North Dakota. The characteristics of the coal are discussed as well as the history of mining and current mining operations for steam coal. The future of the region is tied closely to the ultimate conversion of coal to oil and gas products. Problems of industrial water supply and environmental considerations are covered together with a brief review of current legislation's actions affecting strip mining.

Jan 1, 1973

By C. J. Konya, A. Konya

"Presplitting is a form of blasting that when executed properly will create a smooth wall that will minimize secondary conditioning. In recent years, presplitting has become a popular technique to be used in both the mining and construction industry, however, presplitting fails on many occasions because of ‘geologic conditions’. This is typically because of improper explosive loads consisting of overloading and underloading blastholes. In this paper the authors introduce new factors such as a presplit factor which varies for different rock types, selection criteria for the spacing of presplits, the optimization of explosive load, as well as prediction methods for the environmental affects for the technique of Precision Presplitting. BACKGROUND Methods of controlled blasting in which a smooth, stable wall could be blasted have been an important consideration since blasting in mining and construction has begun. How can one use an explosive, with its massive energy and power, to break a non-homogenous rock without causing backbreak, poor walls, or deviations in the wall over large distances? The blasting industry has known for a long time that blasting ‘high benches’ would result in better walls and less backbreak. However, this was not a sufficiently controlled technique for critical projects, such as the Niagara Power Plant. This was one of the main challenges Hercules Powder faced when they began the project. In order to achieve this, they used a new tool in the explosive engineer’s toolkit, presplitting. The presplitting done on the Niagara Power Project utilized 1 ½” x 8” (38mm x 203mm) 40% gelatin dynamite in 2 ½” (63.5) diameter boreholes. This was done on multiple levels with benches between 12 feet to 52 feet (3.6m to 15.8m) with a total powder factor of 0.75 pounds/cubic yard (0.45 kg/m3). The spacing on these holes ranged between 18 inches to 24 inches (0.46m to 0.61m), center to center (Langfors & Kihlstrom, 1973). The strange aspect of this project was that this “lightly loaded” closely spaced row was fired before the production blast, yet this project produced some of the best walls seen at that time directly from blasting. In today’s blasting industry, presplitting is a more common way to produce smooth, stable high-walls for both the construction and the mining industry. Today, explosive loads for traditional presplitting is generally measured in pounds per foot (kilograms per meter) and typically ranges from 0.30 lb. /ft. to 0.5 lb. /ft. (0.45 kg/m to 0.75 kg/m). MECHANICS OF PRESPLITTING When analyzing a blasting process like the Niagara Project, many wonder how did that work when normally confining a charge would cause cratering and increased backbreak. Since then, presplitting mechanics have been studied extensively. It has been shown in many models that presplitting is not achieve through the collision of shockwave, but by gas pressure in the boreholes. In addition to models and finite element simulations, this has been proven full scale using Pyrodex, a propellant, to create a presplit plane with no shock wave present (Konya, Dean Barrett, & Smith Jr, Presplitting Granite Using Pyrodex, A Propellant, 1986)."

Jan 1, 2017

To generate a most profitable ultimate pit limit is generally the first step in mine design. This paper presents a new graph theory oriented, optimum ultimate pit limit design algorithm which will maximize the total undiscounted net profit. This algorithm performs much better than the well known Lerchs-Grossmann algorithm, in terms of the reduction in computation time and computer memory requirements. This algorithm operates on many directed trees in a graph, where each vertex in a tree represents a block in the mine model. The formation of each directed tree is based more on the ore-waste support concept than the geometry constraints alone. The general procedures of the algorithm, programming considerations and two case study results are discussed in the paper.

Jan 1, 1990

By S. Dereski, G. Chancellor

"INTRODUCTION Barrick Goldstrike underground mine is located in Northern Nevada on the Carlin trend. The underground mine produces approximately 1.5 to 1.8 million tons a year and approximately 400,000 ounces of gold a year. The mine is comprised of two main mining methods, underhand drift and fill and long hole stopeing. The mass blast project stated in 2012 as Value in Use project between Barrick, Southwest Energy and Orica, the goal of this project is to be able to blast an entire drilled stope in one blasting event instead of taking multiple blasts. This will improve productivity by eliminating intermediate blasts, reducing additional blast time, eliminate drill hole cleaning due to the previous blast. Project implantation started in the fourth quarter of 2013 and mass blasting has been common practice throughout all of 2014. STOPPING PRACTICE AT GOLDSTRIKE BEFORE MASS BLAST PROJECT The production from the Goldstrike mine is approximately 70% from stopes. The timely completion of all stoping blocks is imperative to maintaining the plan, delays in the execution of any particular block can have detrimental ripple down effects as neighbouring stoping blocks become delayed. Before the implementation of this project the standard practice for Goldstrike was to: 1. Drill the entire stope 2. Blast a bottom shot, normally between 10 feet and 20 feet off the bottom of the slot rings. This would be mucked out before the next shot 3. Blast a pull through shot, this included the raise and one or two production rings. Again mucking this out before the next shot 4. Blast production rings, one or two more blasts depending on stope size. In most cases between each of these blasts the holes in the other rings of the stope would have to be cleaned. This meant either cleaning manually using air and water, or mechanically cleaning with a bench drill. In many cases this resulted in delays in completing the stoping block."

Jan 1, 2015

By J. S. Chen

DOE recently funded 21 projects under the solicitation by its Environmental Restoration and Waste Management Division. This project is combining the expertise of an interdisciplinary team of researchers with that of three manufacturers to isolate nuclear waste storage sites using remote longwall mining. The concept is being pursued in Germany, too. This paper will present the conceptual approach to the project and discuss the problems in transferring longwall mining technology to nuclear waste containment.

Jan 1, 1994

By H. W. Gao

During the last decade, the feasibility of applying the in situ leaching technology to the recovery of copper from deeply buried deposits containing chalcopyrite has received much attention.(1-4) The major incentive for using this technology is that under certain circumstances, copper in deep underground deposits, which cannot be mined economically by conventional means, can be recovered economically. Basically, this technology involves rubblization of the deeply buried copper ore body followed by in-place leaching of the rubblized copper ores. Rubblization of the ore can be achieved by some suitable method such as the use of block caving mining. The rubblized chimney is then filled with water until the original water level is reached. Leaching occurs when the eater saturated with oxygen is introduced into the chimney- and flows through the fractured rock masses and within pores of rocks. As the dissolved oxygen oxidizes the primary sulfides, heat is generated. Because of low conductivity of the surrounding rocks, the generated heat is able to raise the temperature of the chimney. The increase in the temperature of the chimney and the relatively high content of dissolved oxygen in the leach solution under high hydrostatic pressure will result in an enhanced dissolution of the primary sulfide minerals. To ensure a successful application of the in situ leaching technology, a complete understanding of the effects of the ore particle size distribution, ore grade mineralogy, temperature, pressure, lixiviant concentration, pH, etc. on the rate of copper recovery is necessary so that copper can be recovered efficiently and the amount of copper extracted can be predicted. These can be achieved through mathematical modeling of the in situ leaching process and conducting laboratory tests. In this paper we will present a mathematical model that simulates the in situ leaching process as depicted in Figure 1. To model this process properly, not only the 'kinetic and thermodynamic aspects of leaching chemistry must be known, but the effects of heat generation, the physical aspect of fluid flow and other related multicomponent transport phenomena must be considered. Furthermore, since most factors involved in the leaching process change with time, a leaching system must be described using unsteady state equations.

Jan 1, 1981

By W. J. Wuest

The U.S. Bureau of Mines (USBM) has recently developed a rock mass classification system for evaluating the structural competency of bedded roof strata; the Coal Mine Roof Rating, or CMRR. When compiled with the companion Lotus 1-2-3 spreadsheet, which is simple to learn and use, CMRR data are a useful tool with applications to longwall gate road pillar design, safety hazard mapping, and artificial roof support analysis. This paper demonstrates these applications under actual conditions found in current U.S. mining operations.

Jan 1, 1995