Search Documents

By Manfred Jaeger, Klaus Ertmer, Walter Dietrich, Jochen Greinacher, Wilhelm J. Kogelmann

In Europe, novel low-cost excavator-mounted Multi Tool Miner (MTM) systems, consisting of cutter head, hammer, bucket and drill attachments permit one unit to perform multiple tasks replacing several purpose-built machines. At the Weser Tunnel in Germany, cross-passages between the twin tubes were excavated in frozen ground with a remote-controlled mini-excavator equipped with a quick-change cutter head, ripper tooth and bucket. In Switzerland at the N2 interstate near Basel, W. Dietrich AG enlarged a 2-lane tunnel to three lanes with a cutter head mounted on a special excavator. Blasting and heavy hammers were not permitted due to the closeness of the “live” twin tube. At the N20 Zurich bypass, the Joint Venture of Jaeger, Frutingerand AHB excavates highway tunnels, some with extremely large cross sections, conventionally. A cutter head mounted on an excavator removes the rock shattered by blasting precisely to the pay line, thus preserving the rock’s self-supporting capacity preventing subsidence and damages to water resources and buildings on the surface under low overburden.

Jan 1, 2003

By P. E. Richardson, N. P. Finkelstein, Z. Chen

The large band gap and insulating properties of sphalerite have limited the application of standard electrochemical techniques for studying its reactions with flotation reagents. This problem has been overcome by developing electrodes that rely on the surface conductance produced when sphalerite is activated with copper or other heavy metals. A brief exposure of the mineral in copper sulfate solutions results in electrodes that exhibit significant electrochemical activity characteristic of copper sulfides. Voltammetry studies conducted on sphalerite activated in 10-4 M CuS04, solutions at pH 4.6 provide information on both the amount and the nature of the activation product(s). It is shown that copper activation is strongly dependent on the electrochemical potential applied during activation. Activation at potentials increasingly negative of the rest potential causes a progressive increase in the amount of copper on the surface; activation at potentials positive of the rest potential decreases the amount of copper on the surface. The results indicate that both the kinetics of copper uptake and, possibly, the chemical composition (stoichiometry) of the activation product are controlled by the electrochemical potential.

Jan 1, 1995

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Natarajan K. A.

During sulphide ore grinding, electrochemical interactions between grinding medium and the minerals play a significant role in bringing out enhanced ball wear on the one hand and alter the surface property of the ground minerals on the other. The role of the flotation reagents added simultaneously during grinding with respect to ball wear as well as flotation is yet to be established. Electrochemical measurements such as rest potential, combination potential and galvanic current between sulphide mineral and ball material couples have been carried out in the presence and absence of flotation reagents to understand the nature of electrochemical interactions between ball material and sulphide mineral. Electrochemical mechanisms and models have been proposed to explain the role played by the flotation reagents during different binary, ternary and quaternary interactions with respect to ball wear during grinding.

Jan 1, 1992

By Michael J. Mankosa

Increased emphasis has been placed on recycling consumer and industrial waste products. This trend has created a new industry that is focused on recovery/ separation of byproducts from waste material. As a result, interest has increased in the development of separation systems designed for the recycling industry. Much work has been done in this area. However, existing techniques developed for minerals beneficiation are often ignored. An example of is the foundry industry. There are currently more than 3,000 foundries in operation throughout the United States. Each consumes between 9 and 900 t/d (10 and 1,000 stpd) of sand for mold production. Either silica, chromite or zircon is, used in various combinations with chemical or clay binders. After casting, the sands are typically discarded into a landfill. This practice has become an environmental concern, especially the disposal of chromite and zircon. Silica sand is not environmentally sensitive. But it is used in greater abundance (6 to 7 Mt/a or 6.6 to 7.7 million stpy)and thus has prohibitive haulage and landfill costs. Current technology for sand reclamation involves thermal treatment to remove residual binders followed by dry mechanical attritioning (Leidel, 1993; Klein, 1994). This approach results in high losses due to fines generation and high costs associated with thermal treatment. As a result, this approach has shown only limited success. Stringent regulations are also affecting the disposal of secondary materials, such as plastics and metals. This is particularly true for the ferrous and nonferrous scrap metal industry. It plays a major role in industrial recycling of steel, aluminum and copper. Applications such as wire recycling present challenging problems since a hazardous byproduct (plastic insulation) is generated by the recycling.

Jan 1, 1997

By Mark Gershon

Most recent work in the field of mine production scheduling has focused on either the computerization of the traditional methods or the development of sophisticated mathematical optimization models. Yet it is clear to all concerned that the optimizers need to be made more practical and the traditional approach needs to be made more optimal. This paper, along with another recent paper (Gershon, 85) open a middle ground between these two approaches. In that recent paper, a heuristic procedure for production scheduling was introduced. Here, a series of short term optimizations are used in a creative manner to approximate the true long term optimization. Since these small optimizations are aimed at blending to meet production quality specifications, this approach is most applicable to commodities where the blending function is very important such as coal, cement, phosphates or iron, to name a few. The traditional and the optimization approaches are so far apart that their' advocates have difficulty identifying with the other approach. This is especially true concerning the difficulty of understanding the optimization models for those not trained in the field of operations research. This paper takes the position that the pro- 120 per role of the operations researcher is to provide not only useful and advantageous approaches, but practical, understandable and implementable ones as well. This is the goal of the paper in describing a new approach, consistent with the traditional methods and aimed at approximating the results of the optimizers.

Jan 1, 1986

By I. Chatterjee, M. Misra

The principle of microwave drying of fine coal is based on the selective absorption of microwaves by water. Coal is a poor absorber of microwaves. As a result, water can be removed from fine coal by selectively heating water molecules. One of the difficult problems during microwave heating is the exact determination of temperature in the core of the materials. The electromagnetic energy absorption in coal/water mixtures during microwave drying is controlled by several factors including the dielectric properties of the constituents. In this paper, electromagnetic and thermal models of coal are presented that can predict the energy absorption and temperature distribution during microwave drying.

Jan 1, 1992

By John A. Rajala

The water chemistry of the froth flotation pulp is one of many parameters which can affect the flotation process. The fluid may contain certain inorganic salts which, along with increased ionic strength, can produce undesirable flotation depression or activation. A source of a salt could be the use of calcium chloride to prevent freezing in ore cars, chutes, and bins (Anon., 1980). Alternately, the salt or salts could be initially contained in the water as in the case of sea water and some brackish waters. These salts may become more concentrated because of the need for recycling of plant water due to environmental regulations and/or economic considerations (Davis, F.T., et. al., 1976). The presence of inorganic salts in flotation pulps and their effects upon the recoveries and surface chemistries of different oxide minerals have been the object of various studies. Some researchers (Fuerstenau, D. W. and Raghavan, 1976; Fuerstenau, D. W. and Modi, H. J. 1960; Kulkarni, R. D. and Somasundaran, P., 1977) have reported that addition of a salt can increase or decrease flotation recovery depending upon the particular system.

Jan 1, 1982

By D. C. Rotherham

The Kidston gold discoveries were originally made about 1907, and by 1934, 1.76 Mg (62,000 oz) of gold had been produced from placer and lode mining of higher grade, most¬ly oxidized gold ore. As mining in the lode ore penetrated deeper, costs increased and the world gold price stagnated. The lode or underground production averaged close to 6.9 g/t (0.2 oz per ton) Au for the 201 kt mined. No mining or development took place from 1934 until 1965. Kidston's high grade ores were exhausted by 1934. From 1965 to 1976, exploration had developed 3 Mt of about 3 g/t (0.88 oz per ton) Au. Placer Pacific acquired rights to the property in 1976 and began a geologic and engineering study of the district. It was clear that the deposit had the potential for becom¬ing a large-tonnage, low-grade producer. However, explora¬tion had to discover the tonnage and grade and engineering needed to solve the obstacles of production costs. Bulk material handling problems were addressed by Placer's wide experience in open pit mining, and the increase in work index accompanying deeper ores was handled by Placer's metallurgists. The matter of power for the operation was solved by engineering studies. These showed that power could be generated and brought in economically. The price of gold also increased after 1976, and this helped in the economic analysis. The Kidston discovery since 1976 is really a combination of good exploration geology and careful engineering plan¬ning that overcame the obstacles presented by ore characteris¬tics and the location of the deposit. The attached paper by Harry Mustard is an extract of his honors thesis and explains the deposit geology.

Jan 1, 1990

By Deepak Gupta, Brij M. Moudgil

Attempts were made to improve the recovery of coarse phosphate particles by adding selected frothers or precoated fine particles. A number of frothers for floating, specifically coarse coal and metallic minerals, were examined. Two of the frothers increased the flotation recovery of coarse phosphate by 3% on bench scale. Plant evaluation yielded improvements in overall phosphate recovery in the presence of these frothers. Addition of fine particles was also found to enhance coarse flotation under given conditions. Size, amount, and hydrophobicity of the fines added was determined to have a major influence on the coarse flotation efficiency. The grade of the product with and without frothers and particulate additives remained the same. Change in froth stability and viscosity are believed to be the primary reasons for enhanced recovery of coarse phosphate particles.

Jan 1, 1989

By M. J. Virnig, Marc Le Vier, Rong Yu Wan, Jan D. Miller

Although most gold production from primary resources is achieved by cyanidation, many research activities have focused on alternative processes using noncyanide lixiviants. Such research has been prompted by environmental concerns and problems associated with the processing of refractory gold ores. Numerous research projects have been conducted to search for a noncyanide hydrometallurgical process for gold extraction. In this paper, a technical review of gold recovery from noncyanide solutions is presented, and new results are reported. Gold recovery techniques that are considered include activated carbon adsorption, cementation, solvent extraction, ion exchange, and reduction-precipitation.

Jan 1, 1993

By E. Woodburn, Harrison R. Cooper, R. Putman

The key to concentrator automation is practical means for obtaining continuous assay data from concentrator streams. The technique most successfully used is x-ray fluorescence analysis. The practical reality of on-stream x-ray analysis has been achieved through effort over the past twenty years, marked by an occasional breakthrough, but more typically a step-by-step development to which many individuals and organizations have contributed. The net result of this progress is the present capability to install on-stream x-ray analyzer systems on a turn-key basis. It is now possible to provide all components of an x-ray analysis system as a completely engineered unit which can be put into immediate use, minimizing needs for specialized application know- ledge to benefit from continuous assaying in process control. The economic factors which influence the choice of system and limitations of the x-ray fluorescence technique for slurry analysis are reviewed.

Jan 1, 1976

By H. A. von Schonfeldt, H. Douglas Dahl

INTRODUCTION During the past decade, significant pro¬gress has been made in applying rock mechanics principles to mine design problems by a great number of researchers. Some of these new techniques have found their way into the engineering and planning offices of the operating mine. In spite of these advances, however, the application of rock mechanics in the day-to-day mine planning and design of our domestic coal mines is rela¬tively rare. There are a number of reasons responsi¬ble for this relatively slow progress, not the least of which is the question of how to measure the success or cost effectiveness of a sizable rock mechanics effort in an opera¬ting mine. Firstly, the properties of geologic materials generally vary over a wide range and it is, therefore, difficult to assess whether an improvement in the mining conditions is due to a design change or due to a change in the geologic conditions. A second reason for the slow acceptance of rock mechanics in engineering thinking is the fact that some of the concepts are quite difficult and that physical evidence of their validity to mine design is still rare. Thirdly, com¬munication between research, engineering and applications oriented people appears to function only intermittently. In our view, however, the most important impediment lies in the "state-of-the-art." Exactly how much can rock mechanics help the mine operator? The best that rock mechanics can do at present is determine whether one approach is better than another when weighed against some design objective (stress, strain, deformation). We cannot determine the abso¬lute best ground control design -- only what is better. If ground control is lost, the statement that "it's the best one we looked at" means very little to the harried operator. While the "state-of-the art" has advanced a great deal, it has certainly not been reduced to an engineering matter in that design hand¬books are available -- they are not. The success of a rock mechanics program, there¬fore, can be determined only over a long period of time of continuous effort.

Jan 1, 1977

By R. Hogg, S. Chander

An overview of various physical and interfacial characterization methods for use in mineral processing is presented in this paper. The availability of a large number of characterization techniques and commercial instruments requires that the reliability and limitation of each be carefully examined. The choice of a method may depend upon the manner in which the information is to be used, for example, in development of new processes, plant and process design, plant control, problem solving, etc.

Jan 1, 1987

By Miguel N. Herrera, Abbas H. Mirza, Fiona M. Doyle

The standard test methods used to determine the pyrite content of coal and mineral wastes, and their propensity to release acidic drainage, are critically reviewed. In addition to analysis of total sulfur by combustion, test methods using selective oxidation of pyrite by HNO3 and H2O2 are available. The oxidation kinetics of pyrite vary appreciably from sample to sample, and it is difficult to ascertain whether complete dissolution has occurred in heterogeneous materials. The reliability, reproducibility and suitability of different standard test methods were studied, using well characterized ore and coal pyrite samples. The kinetics of pyrite dissolution were also investigated. The results are discussed in terms of the fundamental chemical and physical characteristics of each sample, and the implications for waste characterization are considered.

Jan 1, 1992

By S. Zaman, F. F. Aplan, Franklin T. Davis

This section deals with the oxides of heavy metals, namely, columbium and tantalum, rare earths, chrome, manganese, titanium, tin, and tungsten. Table I contains the production figures for each of these commodities in the US and in the world in 1977. Specifications for concentrates are also summarized as well as prices for concentrates in 1977. In each chapter an attempt has been made to describe the more common commercial mineral involved with the commodity and the processes used to recover and concentrate the minerals, as well as geographical areas where these processes are utilized.

Jan 1, 1985

In 1992, United States mine production of barite decreased 8.5%. Barite consumption, sold or used by grinding plants, decreased by 36.9% and imports decreased by 61.6% vs. 1991. World mine production decreased 1.5%, according to the US Bureau of Mines. The value of domestically produced barite, f.o.b. mine, decreased 11.9% according to the Bureau. The declared value, c.i.f. United States port, of all imported crude barite during 1992 decreased from $42.35/t ($38.42/st) in 1991 to $40.09/t ($36.37/st). Nevada continued to be the leading producer of barite with 88% of the total, followed by Georgia and Missouri. It is estimated that 80% of the domestically mined barite was used as a weighting agent in drilling fluids. The remaining 20% was used in barium chemicals, glass or as a filler. Most of the production from Missouri, Georgia and Ten¬nessee was used in the non-oilfield sector. Of the total barite used by grinding plants and chemical manufacturers, it is estimated that 90% was used in drilling fluids and 10% in the non-oilfield sector. This included barium chemicals and fillers in paper, plastics and glass. The tonnage consumed in the drilling fluids market decreased due to the lower average rig count during 1992. The average number of rotary rigs operating (717) was 16.6% less than the 1991 average of 860 in the United States. Crude barite imports were 518 kt (571,000 st), 61.6% less than in 1991. Imports accounted for 44.7% of the barite consumed (apparent) in the United States. During the year, China continued to be the leading exporter of crude barite ore to the United States with 67.2% of total crude ore imports. India followed with 31 %, and others with 1.8%. About 90% of the imported barite ore was used in the oilfield sector. Ground barite imports decreased from 46.3 kt (51,000 st) to 30.9 kt (34,100

Jan 1, 1993

By Bruce K. Cantrell, Stephen W. Stein, Kenneth L. Williams, David Hassel, Harvey Patashnick

In June 1992, the Mine Safety and Health Administration (MSHA) published the 'Report of the Coal Mine Respirable Dust Task Group; Review of the Program to Control Respirable Coal Mine Dust in the United States." As one of its recommendations, the report called for the accelerated development of two mine dust monitors: (1) a fixed-site monitor capable of providing continuous information on dust levels to the miner, mine operator, and to MSHA, if necessary, and (2) a personal sampling device capable of providing both a short-term personal exposure measurement as well as a full-shift measurement. In response to this recommendation, the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center, initiated the development of a fixed-site machine-mounted continuous respirable dust monitor. The technology chosen for monitor development is the Rupprecht and Patashnick Co., Inc. tapered element oscillating microbalance. Laboratory and in- mine tests have indicated that, with modification, this sensor can meet the humidity and vibration requirements for underground coal mine use. NIOSH is continuing that effort by developing prototypes of a continuous dust monitor based on this technology. These prototypes are being evaluated in underground coal mines as they become available. This effort, conducted as a joint venture with MSHA, is nearing completion with every promise of success. The immediate benefit of this effort will be to researchers, regulatory personnel, and mine personnel, by permitting evaluation of specific mining practices to see which expose mine workers to excessive dust levels. Using this information, mine personnel can optimize mining procedures to reduce dust exposure. MSHA and the operators will also be able to use the dust concentration data to judge whether dust plan parameters are adequate to continuously maintaining environmental dust levels below the applicable standard. The second development recommended by the Dust Task Group was a person-wearable version of the continuous dust monitor. It will be a monitoring system designed to provide a measurement of worker exposure to respirable dust, both during and at the end of the shift.

Jan 1, 1997

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986