Search Documents

By Robert N. Evans, Delon Hampton

During construction of the Washington Metropolitan Area Transit System, the hand-mining of a mixed-face condition was anticipated on a portion of tunnel located in the downtown area of Washington, D.C. The Section, consisting of two circular tubes, extends from Station 12+80, heading in a westerly direction, traverses along a curve under Lafayette Square, and ends in a northwesterly direction at Station 37+62 (see Fig. 1a). It was near the northernmost portion of the section that the mixed-face condition was encountered. Decomposed rock was first encountered in the invert at Station 31+00. From this point the rock gradually increased in height until it intersected the springline at Station 37+62, the project limit. Summarized within this paper are measurements of the soil load on a horseshoe-shaped portion of tunnel located in the mixed face condition. These measured loads are compared to the soil load on tunnels as determined by current design methods. The paper also discusses rib and surface movements associated with the post loading process. Comments will be made on how the presence of a mixed face condition might help or hender the tunnel design and construction procedures.

Jan 1, 1974

By Gordon M. Pugh, David G. Rasmussen

INTRODUCTION Sublevel long-hole stoping is a large tonnage stoping method that may be used when there is a fairly com¬petent straight vein and the walls will stand with little support. It is a method that lends itself to a high degree of mechanization. Two variations of the method are illustrated in Figs. 1 and 2. Fig. 1 illustrates development typical for a 3-m (10-ft) wide vein. Initial development is by a lower haulageway, which may be either track or trackless. A two-compartment raise is driven in the footwall of the vein. At about 12 m (40 ft) above the main head¬ing, a footwall scram is driven and pockets through the vein are cut on 7.6-m (25-ft) centers. Each of the sub¬level blocks selected in this example is 45.7 m (150 ft) long by 12 m (40 ft) high. Stoping starts at the slot raises at stope endlines and retreats to the timbered raise. This retreat sequence starts on the lowest sublevel and the opening cut is blasted into the slot raise. This retreating system is used in order to provide a good safe back over the miners working in any given sublevel. A crawler-mounted down-the-hole or conventional pneumatic drill puts the holes down from one sublevel to the next on any desired drill pattern. Gravity flow brings the broken ore down to the scram level. The illustration shows a large slusher mounted at the timbered raise and slushing from the pockets back to the raise chute. Development of the ore block in Fig. 2 is typical for a 5.5-m (18-ft) wide vein. Initial development is by a trackless heading driven in the footwall of the vein. Pockets are then put into and through the vein on 7.6-m (25-ft) centers. For ease in using trackless rubber tired mucking equipment, these pockets are crosscut to the vein at approximately 1.04 rad (60°) rather than per¬pendicular. A two-compartment timbered raise is driven down from one level to the next. Endline slot raises are again put through from level to level. Each of the sub¬level blocks selected in this example is 40-m (130 ft) long by 33.5 m (110 ft) high. Stoping starts at the slot raises and retreats back to the timbered raise. Long holes are drilled from one sub¬level down to the next by starting between the lowest pair of sublevels and then working up the ore block. Mucking out of the pocket drawpoints is accomplished by rubber-tired load-haul-dump (LHD) units which then dump into a centrally located orepass.

Jan 1, 1982

By S. B. Hildebrand

One of the highest costs associated with insitu leaching of copper is electric power. The ReGeneration Project addressed this cost issue with a research and development project for BHP Copper. The project involved the installation of a reverse pump/turbine for the removal of excessive fluid pressure and the production of useful electric power. The motivation for the project was that a reverse pump/turbine unit could not only remove the excess hydraulic pressure, but when connected to an induction .generator, would produce electric power, which could be easily connected to the local power gird, thus reducing operating costs. The project was successful in removing excess fluid pressure and producing electricity. The unit is operating today, producing useful 2,300 volt power at a rate of approximately 128 kilowatts.

Jan 1, 1998

By S. P. Singh

In order to understand the intricate nature of blast damage mechanism and to counter the associated problems, small scale blasting experiments were performed on hydrostone, concrete and granite. This was followed by a 2.4 m x 2.7 m (8'x 9') drifting operation in a quartzite quarry. Interior as well as exterior damage was assessed by different techniques. On the basis of the experimental results, the effect of explosive characteristics on the damage was examined.

Jan 1, 1992

By A. Pavlides

The purpose of this work is to conduct a preliminary analysis of the spatial variations of the thickness of lignite layers in the area of the Amyndeo mine, and to estimate the lignite reserves of the mine. The reserves are estimated by the method of the Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. The experimental semivariograms are evaluated for both data sets in different spatial directions. Two possible theoretical models for the experimental semivariogram (the exponential and a novel Spartan model) are compared and discussed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging precision. The performance of kriging interpolation is discussed in terms of cross validation measures.

Jan 1, 2007

By G. Fehr, B. B. Panda, R. Bansberg, K. Arnold, T. Freiman

To evaluate the potential for process solutions to contaminate groundwater outside of the area of the Oxide Pit, it is necessary to predict the ultimate maximum pit lake elevation once pit-related mining activities have ceased. A water balance model was developed based on the existing pit geometry, the groundwater flow equation, and assumed hydrologic input parameters. The model assumed that at any point in time, total inflow into the system (i.e., direct precipitation, surface water and groundwater) minus outflow from the system (evaporation from the lake surface) was equal to the change in the pit water volume. The pit lake depth over time was predicted by assuming a succession of steady- state water balance conditions over short time increments. An analytical method using a spreadsheet and computer model was employed in this study to model the filling of the lake in the Oxide Pit. A sensitivity analysis was performed to evaluate uncertainty associated with the input parameters in the model. The sensitivity analysis indicated that the model was most sensitive to values of precipitation and evaporation and to the static water table.

Jan 1, 2003

Early experiences suggested autogenous mills were difficult to operate and consumed substantially more energy than conventional rod/ball mill circuits. As our understanding has increased and the technology has matured this perception has changed to the point where most new comminution circuits are ag/sag based. In addition many operators have replaced existing conventional circuits with this technology. The JKMRC has been studying ag/sag mills for over 20 years. During this time it has amassed what is probably the single largest and most detailed data base of pilot and full scale mill operations in the world. This has been used to help develop and refine its cur- rent commercially available mathematical model of ag/sag mills. A decade of its application has greatly helped simplify both design and operation of ag/sag milling circuits as well as helping to promote the effective use of recycle crushing, secondary crushing and closed-circuit operation. This paper describes the development of ag and sag milling in terms of our understanding and the evolution of the technology. In addition the application of mathematical modelling and simulation in designing and operating efficient circuits is described with the aid of practical examples.

Jan 1, 1998

By Richard A. Thomas, Liming Yuan, James H. Rowland III, DAVOOD BAHRAMI

To reduce the number of injuries resulting from fires on mobile, diesel-powered mine equipment, it is crucial to promptly suppress a fire once it is detected. The focus of this research was to determine the effectiveness of fire suppression agents. Large-scale tests were conducted using five different fire suppression systems based on: dry chemical, wet chemical, dual agent (dry and wet chemical), carbon dioxide, and water mist. Suppression nozzles were placed around the diesel engine where diesel fuel, engine motor oil, and hydraulic circulating oil spray fires were ignited. The results of this study can help mining companies and manufacturers by providing scientifically based data on the capabilities of the different fire suppression systems.

Feb 1, 2024

By J. L. Fuentes

The so called 'SISCOM' is a General Purpose, microprocessor-based Monitoring and Control System, developed by AITEMIN to meet the requirements of Spanish Mining Industry in - the field of automation and data -transmission. Typical applications -are automatic control of pumps, compressors, fans and conveyors, as well as environmental monitoring and production monitoring. In relation with the last, the - System has been succesfully installed in a full section roadheader and in a mechanised steep coal face. In both cases, the main objective is to get information about running times, down times and causes, -and monitoring of other important parameters such as ventilation, methane content, power consumption..etc. Measurements concerning the face behaviour from a geomechanical point of view are also monitored. These are different pressures and stresses. All data is transmitted to the - surface and on-line analysed by a -desk-top microcomputer. The paper shows the system structure and the requirements that have - been considered on its design. Attention is given to the mechanical data acquisition problem, involving special development of some transducers. The information provided by the surface microcomputer is shown and its utility discussed.

Jan 1, 1986

By M. G. Karfakis

Grouting has been used in underground mining for more than twenty years. Chemical grouting is often used as a remedial measure when the implemented ground control program is unable to completely prevent structural failures or when there is a need for preventing a structural member from unraveling. Utilization of the polyurethane grout currently being used is restricted by its limited range of physical and mechanical properties that restrict its utilization. To overcome some of the drawbacks of polyurethane, research has been conducted on a newly developed polyester based grout. The polyester resin, identified by Sandvik as StrataGrip, provides a number of features, including variable gel times and much reduced chemical hazard. Equally important are the mechanical properties of the product. The strength and deformability of any chemical grout must be compatible with the intended purpose of grouting and the expected deformation of the rock that is to be grouted. Assessment of the mechanical properties of polyester grout is the focus of this work. Field experiences and laboratory research have defined the properties of an effective grouting material. Experimental results indicate that the polyester grout meets or exceeds the recommended properties for many injection applications. Furthermore, the results suggest that the ability to adjust mechanical properties via resin formulation has the potential to expand the applicability of chemical grouting in ground control.

Jan 1, 1997

By Joseph G. Wargo

The purpose of this paper is to investigate trends in exploration expenditures of a selected group of mining companies for the interval 1968 through 1971. The paper also compares these trends with other financial factors that are associated with various groups of companies and comments on the implications of these trends. Although a four-year interval is hardly enough time to establish a long-range set of trends from which operating rules can be derived, the fact that the four years selected are in the immediate past gives some sense of relevance to the matter of exploration expenditures at the present time and in the near future. The sample under study here consists of 21 mining companies. Of these, 19 are listed on the New York Stock Exchange and 2 are listed on the American Exchange. Twenty are American, one is Canadian. All are fundamentally "mining companies" in that they derive the bulk of their income from the extraction, sale, and at times, fabrication of metals from their own mines. This is in contrast to companies which have mineral exploration departments but derive the bulk of their revenues from sources other than mining; for example, from oil and gas sates, Also, no companies which can be considered strictly as exploration companies are included in this study. Although this definition held up fairly well when studying this list in 1968, the strict application of this definition became more difficult through the years up to the present time. In 1971, three or four of the companies were changing their character in that they were phasing out of the mining business, and either deriving their income or planning to derive a substantial part of their income from activities other than mining. A study of

Jan 1, 1973

By Donald C. Wotring, Douglas A. Gabriel, Michael G. Vitale

"The Northeast Ohio Regional Sewer District (NEORSD) recently completed the 24-foot diameter Euclid Creek Tunnel using a steel-fiber reinforced concrete segmental lining. During construction HMM, the McNally/Kiewit JV, CSI/Hanson JV, and the NEORSD performed a test program to evaluate replacement of steel fiber with synthetic fiber. A section of synthetic-fiber-reinforced cast-in-situ lining was also placed as part of the permanent works for the starter and tail tunnels. Laboratory and field testing were performed on two complete segmental rings reinforced solely with synthetic fibers. This paper summarizes the testing program, construction, and results of the synthetic-fiber-reinforced CIP lining and concrete segments. INTRODUCTION The principal feature of the Euclid Creek Tunnel (ECT) project is a CSO storage tunnel that is one component of the Northeast Ohio Regional Sewer District’s (NEORSD) Easterly CSO storage and conveyance system. The tunnel, shafts, and appurtenant facilities will be used for the collection and storage of CSOs from the northeastern part of Cleveland, Ohio and subsequent conveyance to the NEORSD’s Easterly Wastewater Treatment Plant for treatment. The ECT project includes five drop shafts that extend as deep as 220 feet below the ground surface. The ECT alignment and shaft locations are shown in Figure 1. Traditionally in northeast Ohio, tunnel excavations were supported with a two-pass system using steel ribs and timber lagging, followed by cast-in-place concrete. Control of rock overbreak proved difficult with large-diameter two-pass operation, and invert degradation led to train derailments. To mitigate these risks, the ECT was supported using one-pass, precast, bolted, gasketed concrete segments reinforced with steel fiber alone. Tunneling operations were very successful and experienced no significant delays or claims. As a result of the positive ECT experience with steel fiber-reinforced segments, Hatch Mott MacDonald, LLC (HMM), McNally/Kiewit (MK) joint venture, CSI/Hanson (CSI/H) joint venture, and the NEORSD performed a test program to evaluate replacement of steel fibers with synthetic fibers in segmental rings. This paper presents the laboratory and field testing program, construction, and results of the synthetic-fiber-reinforced cast-in-place (CIP) lining and concrete segments."

Jan 1, 2016

By Harrison A. Schmitt

During .the past five decades or so we have passed from a time when it was difficult to point to a mine or an ore body and verify that it had been discovered by geological methods, through the. Twenties when the common saying was, "Who ever heard of a mine found by a geologist?", to recent decades when hundreds of mines and ore bodies are acknowledged geological discoveries and the above query can be ignored. Recently, however, the application of mining geology appears to have been downgraded, or so it seems to me. Basic geology in mining has been cheapened and glossed over in favor of geophysics and outcrop sampling, even though the latter is merely one technique of mining geology and, to some extent anyhow, has been used for a. long time. (Locke, 3, pp 81-87). Geophysics by itself and in conjunction with geology has had success in certain geological provinces, but limited attainment in mountainous terrane except in those few cases where strongly magnetic minerals are associated with ore. Nevertheless, in the Cordillera .many experimental techniques are offered as proved ones. This is not an intent to try to depreciate honest geo- physics. Continued experimentation and use of it is approved by all, but at the same time it is foolhardy to throw mining geology overboard, Generally both approaches should be considered and usually, at first anyhow, geology is the most direct one.

Jan 1, 1960

By C. P. Newman, T. Gray, G. Beale, T. Cluff

Predictive geochemical and limnologic modeling of pit lakes is an important aspect of modern permitting. One of the key assumptions of many predictive pit-lake models is that highwalls and pit backfill become unreactive once submerged by the filling pit lake. Existing pit lakes provide useful data to test this assumption. The Sleeper pit lake (northwestern Nevada) is near hydrologic equilibrium and contains good-quality water that generally meets regulatory requirements for pit lakes. Despite the overall stable geochemical composition, seasonal trends in the hypolimnion indicate the generation of solutes and fluctuations in pH. This work applies mass balance, analysis of subaqueous pyrite oxidation, and trends in solute concentrations to evaluate the potential causes of long-term solute generation in the hypolimnion of the Sleeper pit lake. Results will aid in refining the effect that inundation of highwalls and waste rock has on ultimate pit lake chemistry and long-term closure planning. In the case of the Sleeper pit lake, ongoing solute loading does not substantially change the closure plan at this time as influent groundwater contains abundant alkalinity. INTRODUCTION As mine pit lakes become more widespread, regulatory agencies are increasingly requiring advanced predictive modeling of pit-lake geochemistry during permitting. The end goal of all those involved in these permitting actions (i.e., the mining company, the regulatory agencies, and the public) is to have pit lakes become geochemically and hydrologically stable for the long term, which may then allow mining permits to be relinquished. The modeling endeavors therefore are important to inform long-term closure of pit lakes. The conceptual models and numerical methods used to predict pit-lake water quality are complex and require substantial amounts of data and a variety of assumptions (Castendyk et al., 2015). One of the common modeling assumptions is that solute generation via acid mine drainage is eliminated (or at least decreased) by the filling of the pit lake and inundation of highwalls and any in-pit waste rock. However, few studies have reported on observations that support or refute this assumption. The water-quality record of the Sleeper pit lake is an ideal dataset with which to test these assumptions. The former Sleeper mine is located in northwestern Nevada (Fig. 1), and has been inactive (in terms of ore extraction) since 1996. The mine extracted Au and Ag from the famous high-grade Sleeper vein and associated widespread stockwork mineralization (Nash et al., 1995). Water quality in the pit lake has been monitored since the cessation of dewatering in 1996. The current pit lake actually occupies three separate sub-pits, the Sleeper, Wood, and Office pits (Fig. 1). The Sleeper and Wood pits undergo regular water-column monitoring using a conductivity-temperature-depth (CTD) probe, and sampling for dissolved inorganic constituents at several depths (~10, ~130, and ~330 ft. below lake surface). Groundwater quality is also monitored using a series of wells (Fig. 1).

Jan 1, 2019

By C. W. Schultz

Introduction The Mineral Resources Institute, The University of Alabama, has for the past three years been engaged in a program to develop a beneficiation system for eastern (Devonian) oil shales. One objective of that program was to evaluate advanced technologies for effecting a kerogen-mineral matter separation. Column flotation was among the advanced technologies selected for evaluation. Early in the program it was shown that column flotation was superior to conventional (mechanical) flotation and to the other advanced technologies being evaluated. The investigation then proceeded toward the further objective of defining the optimum operating conditions for column flotation. One observation made in the course of optimization testing was that introducing the feed into the froth (above the pulp-froth interface) resulted in an improved combination of concentrate grade and kerogen recovery. This observation was reported in a previous paper (Schultz and Bates, 1989). Because the practice of maintaining the pulp froth interface below the feed point is contrary to "conventional" practice, it was decided to subject the observation to a systematic series of tests. This paper describes a recent series of tests and the results that were obtained.

Jan 1, 1991

By C. E. Jordan

The fundamental properties of the Bureau of Mines patented dielectric separator were studied to provide insight regarding its design and operating characteristics. Force equations for mineral particles were derived and evaluated experimentally. High dielectric mineral recovery was proportional to the calculated effective dielectric force volume that surrounded each drum electrode wire. Electrode spacing was the most sensitive design parameter, requiring less than 0.4-cm electrode spacing for a good separation. Operating characteristics and ore characteristics were investigated. With a dielectric constant difference as small as 2, good separations were made on a laboratory scale at energy consumption below 12 kw?h/mt.

Jan 1, 1985

By T. W. Camm, J. C. Johnson, S. D. Rosenthal

"Most engineers are bright, hard-working, reliable and prefer to avoid conflict. An engineering curriculum tends to self-select these characteristics. By most standards, you would expect workers exhibiting these traits to require minimal supervision. But, is this true? Is this how most current engineering managers lead? Looking at some current theories on leadership combined with personal anecdotes, this article will look at some common misconceptions about leading engineers.Engineers are different. There, it has been said. From cartoons to movies to television shows and more, there is a reason stereotypes of engineers resonate. Yes, you can find a lot of individual variation among specific engineers that you may know, but they do not detract from some of the overarching commonalities that engineers are known for.Clash of culturesWhat distinguishes a professional? Raelin (1985), in his book Clash of Cultures, describes professionals as having superior intellectual training, maintaining their own standards of excellence and being supported by associations that maintain the quality of the profession. Engineers obviously fit all three of these ideas: an engineering degree is still regarded as one of the most difficult to attain. Standards are maintained both through peer review and in academia, through ABET accreditation and through professional associations like SME to promote the discipline and foster technical growth.Six characteristics representing professional status are described by Raelin (1985, p. 9):• Expertise — prolonged specialized training in a body of abstract knowledge.• Autonomy — the freedom to choose the means to solve a problem.• Commitment — primary interest is in pursuing the practice of one’s own chosen specialty.• Identification — identifying with the profession and with fellow professionals, both through formal associations and through peers external to the organization.• Ethics — providing service without concern for oneself or without becoming emotionally involved with the client.• Standards — committed to help in policing the conduct of fellow professionals."

Jan 1, 2018

By Christopher J. Bise

Traditionally, mine drainage systems have not received the high level of emphasis on careful engineering design which has been rendered to many of the other auxillary operations. This may be due, in part, to the situation-response approach toward dealing with an influx of water. When the installed system becomes inadequate, costly alterations to the pump, such as staging or speed increases, are considered expedient solutions. In order to rectify this situation, computer-aided solutions to mine drainage problems could represent an efficient alternative to the methods presently used. This paper will consider the application of microcomputer technology to mine drainage problems and will show how the relative economy and convenience of microcomputers can make them become valuable analytic tools at any mine site.

Jan 1, 1983

By Kevin Sierra, Orfelinda Avalo, Julio Guizado, Edwilde Yoplac, David Martinez

Mining tailings are slurry byproducts of mineral recovery. They generate serious environmental risks due to their toxicity when exposed to water and oxygen. Studies focus on eco-friendly alternatives for mitigating these environmental impacts. Processing these tailings enables a sustainable mineral production model through circular economy practices. This study evaluates using gold mining tailings to recover gold and produce bricks. Flotation tests obtained a concentrate with 86.66% gold recovery, containing sulfides (pyrite, arsenopyrite) and a tailing with silicates and oxides suitable for brick manufacturing and ornamental pieces. This approach promotes eco-friendly solutions and a greener approach to mining operations.

Feb 1, 2024

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998