Search Documents

By Richard A. Allwes

A procedure is presented for the design of an arch canopy for the application of rehabilitating a high-roof-fall area. This procedure is specifically developed for evaluating an unbackfllled arch canopy, which Is subjected to an impact load (roof fall). Dynamic line loading of the arch canopy at its crown is only considered and the procedure does not account for an unsymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation is dependent upon many variables, including in-nine conditions and the engineering properties of the structure. However, a general evaluation can be based upon a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. A single spring-mass system is used as an idealized model to represent the dynamic behavior of the arch canopy at its crown. An energy approach is taken to determine the maximum crown deflection of an arch rather than solving a differential equation of notion derived from dynamic equilibrium. The design procedure is based on the concept that when an arch canopy is subjected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure Is that It gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1986

Excessive roadway closure in the gateroads impedes the passage of equipment, supplies, personnel and ventilation air in longwall panels. This pager describes several factors that influence the gateroad stability and presents some measures to alleviate the problem.

Jan 1, 1994

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993

By Yi Luo

The responses of a section of railroad to ground subsidence process was monitored as it was undermined by a longwall panel. The subsidence data collected and the observations made through this monitoring program could help us understand betteer the ground subsidence process and its impact on linear structures such as railroads. The data analysis techniques used and the assessment methods presented could be useful to researchers practitioners in the field of mining subsidence.

Jan 1, 1994

By George Gardner

The rapid growth of highwall mining in the Appalachian coalfields has resulted in unique safety concerns. Due to the concentration of activity at the base of the highwall and the potentially destabilizing influence of the mining process, proper mine planning and continual monitoring of the ground conditions is essential to ensure a safe and productive operation. This will also help to minimize the need to recover equipment that has become entrapped underground, and the subsequent hazards associated with a recovery operation. Adequate geotechnical site investigation and rational design methods should enable mine planners to properly account for the site-specific conditions that influence web and abutment pillar, roof, floor, and highwall stability. This paper examines the growth of highwall mining, provides a general overview of the various safety concerns, and reviews the modes of highwall failure as they relate to a highwall mining operation. Gcotechnical considerations that should be taken into account before and throughout the mining operation are emphasized. The importance of closely examining and monitoring highwall conditions for subtle signs of highwall instability will be discussed.

Jan 1, 2002

By Bob Thomas

The roof drill operator productivity can be enhanced by the introduction of control technology The operators control station can be improved by considering human factors such as handle forces and control location. The smaller electrical controls can be located much easier than the traditional hands on valves. The operators control can he improved by using processors with programmable subroutines that assist the operator in the decision making process. For example to increase feed rate - to slow rotation - to avoid clogged steels - etc. The overall affect is to improve drilling and bolting consistency. The control system uses a dedicated processor packaged as an intrinsically safe control station. The roof drill operator is assisted in the drilling; arid bolting by a closed loop feedback system. The processor monitors the drilling parameters such as feed force, feed rate, rotation torque, RPM, drill position, and vacuum condition Based on the drilling parameters the processor executes pre-determined condition statements intended to enhance drilling The drill operator has an active display to alert him to the real time machine status. For example if the feed were to slow or delay due to a high vacuum level the display would show "high vacuum". The dedicated processor is available on the arm feed style machines, The prototype machines used programmable logic controllers to develop the feedback relations. The ability to record drilling parameters was extremely helpful in this development project. The extended use of the recording feature will aid operators in mapping the mine roofs Interpreting the recorded drilling parameters can reveal a void in the top or hard competent drilling The prototype machines also showed the importance of vacuum monitoring This feature is extremely valuable in softer materials, The benefits of the control system range from efficient use of the consumable bolting materials to uniform operator performance.

Jan 1, 1999

By William Bookshar

The development of increasingly more sophisticated and powerful retreat longwall equipment has led to ever wider and longer panels. To maximize gateroad development efficiency, provide for effective face recovery, andlor reduce ventilation pressures, entries are cut across longwall panels in advance of longwall retreat mining. These entries must be supported to prevent falls of immediate roof in advance of the face. Recently, cut through entries and predriven recovery room entries have been supported with various combinations of roof bolts and passive support. The cost and relative success of these support systems has varied considerably. Eighty-Four Mining Company, Fosroc, and Sub-Technical have developed and implemented an efficient, yielding, multiple component, cement crib to support longwall panel cut through entries and pre-driven recovery rooms. The cutable crib consists of an inexpensive flyash cement pillar poured in a bag, within a temporary metal form. The form is moved to a subsequent cutable crib location after the initial hardening of the flyash pillar. The remaining entry height between the mine roof and the top of the flyash cement pillar is filled with a specially designed bag filled with Fosroc's Tekset cement formulation. The diameter of the pillar and thickness of the Tekset bag are designed to accommodate the anticipated front abutment loading and entry convergence.

Jan 1, 1998

By John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U.S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of a recorded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with hump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip. etc.) of the failure of the strata surrounding the active and multi¬panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

Jan 1, 2000

By P. R. Sheorey

Four case studies of special geomining conditions from Indian coalfields are discuss- ed. These cases relate to (a) pillar extraction in two seams simultaneously under a difficult roof (Satpura I and II). (b) depillaring in an inclined seam resulting in rib instability (Sudamdih), (c) depillaring resulting in floor lift and side spalling (Jarangdih) and (d) contiguous pillar extraction under hard incavable strata. Solutions to these problems are given based on rock mechanics principles involving stress analysis, classification techniques, past experience and engineering judgement.

Jan 1, 1988

By Qiang Fu

ABSTRACT This paper aims to identify the main issues concerning top-coal loss and the optimum drawing interval of LTCC (Longwall Top-coal Caving) mining by underground tests and DEM (Distinct Element Method) modeling. By extracting a new roadway in the goaf of the mined LTCC Panel No.4318 in Wang Zhuang coal mine of Lu-an CMA (Coal Mining Administration), and underground observation of the distribution of loss coal and broken rock in different sections of the roadway, this paper analyses the composition and presents a 3-D distribution map of the loss coal in the exploration roadway. This study indicates that the DEM modeling of broken top-coal is reasonable and scientific as it can simulate the movement of broken coal and waste rocks and determine the optimum drawing interval of top coal.

Jan 1, 2002

By Hamid Maleki

A new failure criteria is proposed for assessment of roof stability in underground sedimentary rocks. Unlike other stability assessment techniques, this method is simple and practical, having improved mine safety and productivity in several mines. It is shown that roof movements accelerate to a critical rate prior to actual roof collapse. Critical rates vary between 0.025 inches per day to 0.2 inches per minute depending on rock mass - pillar mechanical properties. Specific critical rates are determined for three rock mass - pillar categories which are common to mining in sedimentary rocks. Time-to-caving varies from one minute to ten days on rock structural controls and type of primary support utilized.

Jan 1, 1990

By James M. Tennant

In the mid 1970's, American Electric Power significantly expanded its internal coal production. This involved opening several large mines in seams that had never been mined on a large commercial scale before. One of the mines opened was the Martinka No. 1 Mine which is located approximately five miles southeast of Fairmont. The mine was originally designed for room and pillar mining with continuous miners but was later modified to permit the utilization of longwalls and continuous miners for entry development. The coal seam to be mined was the Lower Kittanning which averages fifty-six inches. In order to successfully mine this seam, it required that the mine design recognize the effect caused by the dip of the seam which averages four percent to the Northwest with a maximum of sixteen percent for short distances and a relatively low cover. In fact, seventy-four percent of the reserves have cover of less than four hundred feet. Also, the core hole data indicated that the immediate roof varied from zero to eighteen feet of shale with two to forty-five feet of sandstone overlying the shale.

Jan 1, 1982

By Tom Denton

The bolt design criteria, since it was first published by Dr. John Stankus (Stankus, 1997), has been recognized as an important tool in ground control design. This concept is based on the Optimum Beam Building Effect (OBE), which is defined as the roof beam that has no separation above or within the bolted range and having the shortest bolt possible. This paper will present an application of this concept at the American Coal Company. Galatia mine. This mine previously used a 6' and 7' length bolt. However, since seam thickness has gotten smaller in the Southern area of the nine, a two-piece bolt is required. A two-piece bolt increases ground control costs and delays production. Therefore, a one-piece, shorter bolt, if feasible, can reduce costs and expedite development. In this analysis, Computer modeling is first conducted to determine bolt length and installed load. Second, a special bolt is developed, that can achieve the proper installed load as determined by the computer modeling. Third, underground bolt pull and load cell tests were conducted to evaluate bolt performance. Finally, an underground "bench" test was conducted. The test results have shown that entry convergence in the short bolt (5) test area is less than the 6' bolt area. Overall roof condition in the test area was as good as the 6' bolt area. Based on this analysis, the mine has converted to a shorter bolt in the low seam area and it is working well.

Jan 1, 2000

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By J. Riefenberg

U.S. Bureau of Mines (USBM) researchers are developing a personal computer-based hazard mapping system for use in underground coal mines. Hazard mapping is rapidly gaining interest as delineating areas of possible instability is becoming more complex. The development of a hazard map is based on the consensus that combined effects of local and regional stresses, roof, floor, and rib quality, geology, faulting, presence of ground water, etc., all contribute to stability of the ground. In order to demonstrate the concept, a hazard map was developed that combined stresses anticipated to occur in a multiseam setting using numerical modeling, and the newly developed Coal Mine Roof Rating (CMRR) where roof quality ratings in untested areas were modeled using geostatistical methods. Ten borescope readings from an underground mine were used to compute CMRR's for the geostatistical analysis. CMRR's for the mine ranged from 57 to 77, and are considered in the moderate to strong range. A hazard map was developed by combining the stress effects of interseam mining, scaled to weigh equally with CMRR's, and CMRR geostatistical analysis results. This hazard map demonstrates a synergistic effect between the mining-induced stress fields and the roof quality ratings, indicating, as expected, a greater hazard index in areas of high stress and lesser roof quality.

Jan 1, 1994

By David C. Oyler

Few studies have specifically measured and documented the large-scale loading behavior and durability of ventilation stoppings to mining induced movements, particularly from longwalls. Ventilation stoppings are more commonly the concern of ventilation engineers, and ventilation, topping response to ground movement has only been documented in an incidental manner. This paper presents the investigations of underground measurements that have been conducted to determine the loading response of stoppings constructed from lightweight aggregate concrete masonry units (CMU). These investigations have produced some interesting results that may prove beneficial, not only for developing and assessing alternative stopping construction techniques, but also for designing and selecting standard construction methods for use in varying mining conditions. For instance, the interface friction that results from wedging a CMU stopping during construction plays a substantial role in its ability to resist both lateral and vertical loads. Although they are not intended for ground support, the study showed that block stoppings can resist vertical loads of at least 2,700 to 3,000 kN. Asymmetric loading of a stopping may result in localized failure of blocks within a stopping, which, depending on the severity, can be a precursor of impending stopping failure. In addition to measurement results and implications, the paper will also present details of field measurement methods used to assess stopping response. Stopping stiffness and material strength characteristics will also be presented,

Jan 1, 2001

By Dieter Wittenberg

The use of thc ultrasound technique for monitoring rockbolt support has at last provided support engineers with a measunng system capable of pinpointing fracture failuns in fully-grouted rockbolts. The measurement data are based on the operatmg characteristics of the bolt type, which are determined both under test-bench conditions (DIN 21521) as well as in underground trials. Practical experience acquired to date suggests that this new measuring system is both effective and reliable.

Jan 1, 2001

By Eddie Martin

Jim Walter Resources, Mining Division, employs the retreat longwall mining system as the primary method of coal production. The strata control aspects of developing and maintaining roadways for retreat longwall mining have continued to improve and advance at Jim Walter Resources. New and innovative concepts in pillar design, roof and rib support, as well as longwall face support, have been combined to provide better strata control. Control of immediate roof breakup in the headgate and tailgate entries has been a problem at Jim Walter Resources' mines. The application of roof trusses as supplemental roof support failed to provide the desired strata stability. The immediate roof deterioration has been controlled through the installation of increased density of roof bolts in the affected roadways. Control of the rib sides has been a documented problem at Jim Walter Resources' No. 4 Mine since its start-up. The installation of 3/4 inch diameter roof bolts at 2 ft. spacing failed to control rib rolls. The development and application of a yieldable rib support system provided the desired results. Rib rolls have been virtually eliminated where the yieldable system of rib support has been installed. An evaluation of longwall panel development using the total yield pillar mining plan has been completed. Results of the strata stability and other operational data have been compiled. Coal production and gate entry stability were not adversely affected using the total yield pillar mining plan for longwall panel development. Strata Control on the longwall face is provided by the face support system. Excessive convergence and roof breakup along the longwall face have been experienced at several of the Jim Walter mines. In an effort to eliminate this problem, an evaluation of higher setting pressures for longwall face supports is being conducted. Results have been inconclusive to date. Each of the above strata control projects will be presented as case studies. Since Jim Walter Resources business is coal production, emphasis will be directed toward the application rather than the theoretical aspect of the projects.

Jan 1, 1988

In this paper, the plastic increment theory was applied in a 2-D finite element model, and a generalized Von Mises yielding criterion adopted to simulate the progressive failure of coal pillars. Extensive underground monitoring was conducted and the data compared with the computer model, yielding promising results. Three different longwall entry layouts, including a stable (s-s) pillar system, a yield-stable-yield (y-s-y) pillar system and a yield (y-y) pillar system, were investigated using the model developed. The yield-stable-yield system was considered to be the best of the designs studied in the case. A comprehensive parametric analysis was also performed. The triaxial factor and Poisson's ratio were found to be the most important material parameters affecting pillar yielding.

Jan 1, 1988

By S. Paul Singh

The implications of blast damage are harmful in both economic and physical sense. To understand the mysterious nature of blast damage assessment and prediction, field work was done by driving an experimental tunnel in the bench of a quartzite quarry. On the basis of the blast vibration monitoring records, a model was developed to predict the PPV at different distances from a blasthole. Critical particle velocity for damage and the output of the prediction model were used to delineate the extent of damage for different explosives. The predictory model was tested by designing a special blast and the burdens for the back holes have been recommended. The relationship between the critical particle velocity for "Fall Off' and the critical particle velocity for damage has been established. The existing criteria for blast damage have also been renewed in this paper.

Jan 1, 1993