Search Documents

By Yanhui Sun, Yanan Zeng, Kaike Cai

"Hot ductility of Nb-V-containing steel has been studied by theoretical calculation and thermal simulation experiment. Meanwhile, microsegregation and precipitates were analyzed. The results showed that segregation degree of elements S, P, 0 is greater in mushy zone, while, the hot ductility was deteriorated by inclusions of Fe(S,O), (Fe,Mn,Si,Al)(S,O) in the interdendritic region. At the temperature 1100°C, a few NbN particles, 60-70nm, have little effect on mechanical property. In the temperature range 1000°C to 975°C, R.A declined rapidly from 82.36% to 69.61% with the diameters decreasing from 20 to 10nm and quantity of particles increased 23 to 45inds/µm2, respectively. In the temperature range from 900°C to 850°C, R.A reduced unobviously from 34.27 % to 30.01 % with ferric films thickening gradually. The critical stress, 52.38MPa, was equal to tensile strength at 975°C. Intergranular fracture was easy to occur with higher critical stress below 975° C.IntroductionProductivity and product quality of slab are seriously affected by cracks during continuous casting and the influencing factors of cracks are various[l]. From microcosmic angle, resisting deformation ability of initial solidification shell decreases obviously with solute elements segregation which can urge the low melting point ofliquid film to form at grain boundaries[2, 3]. Meanwhile, with temperature decreasing, particles would precipitate as the practical solubility product is greater than equilibrium solubility product. The carbonitrides would lead to stress concentration at austenite grain boundaries. Therefore, the transverse cracks of microalloyed steel would form during the straightening operation in the continuous casting process. The hot ductility of steels in the temperature of mushy zone was characterized by microalloy elements segregation, zero strength temperature (ZST) and zero ductility temperature (ZDT). The nature, shape, and size of precipitates have been investigated by TEM (JEM2100). Hot tensile test with low strain rate was simulated by Gleeble-1500. The objective of present study is to provide reference for zero defect of microalloyed steel during continuous casting process."

Jan 1, 2013

By Kimio Itagaki

"As a contribution to understand the smelting of copper or nickel matte by blowing oxygen or oxygen-enriched air, the phase equilibrium and the distribution of minor elements between the iron-silicate based slag and the Cu2S-FeS or Ni3S2-FeS matte at 1573K were investigated in a magnesia crucible under controlled partial pressures of SO2 at 0.1, 0.5 and 1.atm. At a given matte grade, the solubility of copper in the slag was found to be independent of p5O2 while that of nickel was dependent on pSO2 and these behaviors were analysed thermodynainically based on a concept of oxidic and sulfidic dissolution of the components in the slag. When the matte grade was specified, the distribution ratios of X, defined as (wt pct X in slag)/(wt pct X in matte}, for As, Sb and Bi increased with increasing p5O2 while that for Ag was constant against p5O2.IntroductionA combination of intensive reactors with the use of oxygen or oxygen-.enriched air as the blowing gas has provided a number of improved copper and nickel smelting processes such as INCO-Flash, Outokumpu-Flash, Mitsubishi-Continuous and IBRC (top blown rotary converter) processes. Phase equilibrium and thermodynamic studies for the slag and the copper matte or the nickel matte under high partial pressure of SO2 are of practical importance for evaluating the behaviours of the related components in the oxygen-smelting.A series of experimental studies have been already conducted in a limited range of conditions for Pso2 around 0.1 atm, which corresponds to the smelting with air-Stowing [1-5]. However, there remain very few data on the phase equilibrium in the matteslag systems under higher partial pressures of SO2. Tavera and Davenport studied the phase equilibrium between the copper matte and fayalite slag phases under the partial pressure of SO2 controlled at 0.1 - 1 atrn but without controlling the partial pressures of sulfur and oxygen [6]. A potential diagram for the Cu-Fe-S-O-SiO2 system at 1523 - 1573K suggests that the partial pressure of S2 equilibrated with the matte and the fayalite slag with saturated SiO2 under the high SO2 pressure is considerably high at 10-4 - 10-2 atrn [7]. This condition must require controlling of p52 as well as Pso2, in the equilibrium experiments, otherwise, the equilibrium condition may be hardly attained due to the continuous flushing of sulfur from the system."

Jan 1, 2000

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By Y. Z. Zhang

Electrochemical oxidation of arsenopyrite in ferric sulphate media in the absence and presence of bacteria T jerrooxidans has been investigated for the purpose of understanding the dissolution chemistry of arsenopyrite and the bacteria attack mechanism. Mixed potential, polarization resistance measurements, polarization curve, cyclic voltammetry experiments were conducted in a ferric sulphate medium of 10g/L FeH, temp.25-35°C, pH 1.5-2.5 in the absence and presence of bacteria Tjerrooxidans, respectively. For the anodic process, a two-step reaction sequence is suggested by the electrochemical measurements. The initial step at a low potential is described by:

Jan 1, 1996

By R. Y. Wan, S. L. Chryssoulis

"Gold associations were established in a·biooxidized, chlorinated CIL residue assaying 0.02 oz Ault and in a biooxidized thiosulfate leach residue assaying 0.01 oz Au/t. A detailed mineralogical study involved: assays of screened fractions; light microscopy; ion probe microanalysis to quantify 'invisible' gold in sulfide minerals; proton probe microanalysis to detect and quantify preg-robbed gold. In the CIL residue, most of the gold is preg-robbed (71 %). In the thiosulfate leach residue, gold occurs mainly as submicroscopic disseminations in microcrystalline quartz (chert). In both residues, the 'invisible' gold in pyrite accounts for a minor fraction of the gold assay. Quantitative determination of the gold occurrence in the two residue samples established conclusively that gold adsorption on carbonaceous matter in the thiosulfate leach is of minor importance.Acknowledgement: published with permission of Newmont Gold Company."

Jan 1, 1997

By Wade L. Karlsen

"Revision surgery to replace joints in the human body requires materials that are strong, long-lasting, and biocompatible. Metallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an on-going effort to economically improve their performance. Alloying with inert nitrogen can enhance the mechanical properties of the alloy, enhance its corrosion resistance, and elevate the temperature at which the metallic implants can be thermally treated, without increasing the threat to the human body. The current work has produced a high-nitrogen Co-Cr-Mo alloy through HIP consolidation of metal powders that have undergone nitriding in a mechanically fluidized bed. The already fine microstructure of the powders combined with the increased nitrogen content resulted in significant property gains in the consolidated materials.IntroductionMetallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an ongoing effort to improve their performance. Research on a Stellite 21 cobalt-chromiummolybdenum alloy has shown that nitrogen alloying can be desirable from several standpoints [l]. Firstly, it has indicated that nitrogen can enhance the mechanical properties of the alloy, which could allow more demanding implant designs. The same work also demonstrated that nitrogen can elevate the temperature at which the metallic implants can be thermally treated, which is desirable in situations in which surface textures are to be sintered to the implant to enhance its fixation properties. Finally, that research work discovered that, not only does nitrogen not harm the corrosion resistance of the cobalt-chromium-molybdenum alloys, but it may in fact enhance it. Combining this with the fact that small amounts of nitrogen are not considered a threat to the human body, makes nitrogen alloying an attractive alternative for enhancing the properties of Co-Cr-Mo."

Jan 1, 2000

By Takashi Araki

In this work, we have elucidated the two-step oxidative reaction mechanism of 2,4,5-trichlorophenol by adsorbing oxygen atom for oxidative decomposition reaction of 2,4,5-trichlorophenol on oxide catalyst surface using ab initio molecular orbital calculation. In the first oxidation, total energies of reaction products have been shown extremely stabilized at all oxidation positions. This reaction occurs due to charge transfer from benzene ring to adsorbing oxygen atom. As a result, 1£ bonding of benzene ring are weakened. However, the benzene ring of 2,4,5-trichlorophenol does not perform cleavage reaction. In the second oxidation, the benzene ring of2,4,5-trichlorophenol can perform cleavage reaction, since the second oxidation obtains larger stabilized energies than the first oxidation.

Jan 1, 2003

By Yoshinao Kobayashi

he removal of oxygen from titanium and zirconium is important for use in application because it significantly affects the mechanical and physical properties such as ductility and toughness. However, thermodynamic properties of oxygen in molten titanium and zirconium have not been clarified and the effective deoxidation process of molten titanium and zirconium has not been established. In this study, the standard Gibbs energy of reaction of oxygen and yttrium in molten titanium and zirconium have been measured by a chemical equilibrium technique. Molten titanium, zirconium, and their alloys with aluminum were equilibrated with a Y2O3, A12O3, or Zr02 pellet in a cold crucible. The results are summarized as follows:

Jan 1, 2000

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

By D. Doungdeethaveeratana

The extraction kinetics in a novel solvent extraction process have been investigated. In this process, the liquid-liquid emulsion is generated by bottom gas injection into countercurrently flowing aqueous and organic phases. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration, without any mechanical moving parts, and the ease of cleaning and process control, while providing a sufficiently large interfacial area for rapid mass transfer. The overall rate increased with increasing gas injection rate and height of the aqueous phase but decreased with increasing injector diameter at the same gas injection rate. The variation of the overall rate constant was correlated against a set of dimensionless numbers, representing the operating conditions. Extraction rates and efficiencies comparable to those in a mechanically generated emulsion were attained in this new process.

Jan 1, 1998

By Batric Pesic

A hydrometallurgical process for recovery of Zn and Mn from Bunker Hill Water Treatment Plant sludge was developed. The process is unique because it treats an unusual combination of metals, Zn and Mn. Another non-standard feature of the process is that leaching takes place with ~S04 in the presence of a reductant (SO2). Zn and Mn are recovered simultaneously by electrowinning, Zn on a cathode and Mn on an anode, as MnO2 The major purpose of the process is to detoxify the sludge by removing toxic heavy metals. The recovered metal values could be marketed to offset the overall costs of water and sludge processing. This work is presented in two separate parts, 1. Leaching and Solution Purification, and II. Electrowinning. This paper covers only the first part of the hydrometallurgical process: Leaching and Solution Purification. Initially, the paper briefly discusses the history of the pollution problem at the Bunker Hill Superfund Site, the origin of heavy metals in the mine waters, and the development and use of the water treatment plant. The leaching of sludge was examined as a function of the following parameters: constant vs. initial pH, initial vs. delayed addition of SO2, temperature, and pulp density. It was found that leaching with H2SO4 at pH 2.0 for 15 minutes (at 60°C), followed by S02 addition for another 15 minutes, could completely dissolve Zn and Mn. Solution purifIcation was done in three stages. In the first stage iron was removed by adjustment of pH (to pH 5.0) and oxidation offerrous to ferric iron (with H2O2). In the second stage, Cu and Cd were removed by Zn dust cementation. Finally, Co and Ni were precipitated with the organic reagents 1-2 nitroso-naphthol and nitroso, respectively. Electrowinning of Zn and Mn is discussed separately in Part II of this paper.

Jan 1, 1996

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By Adolfo Pillihuaman Zambrano

Fe-Cr-C production is a very high electrical energy consuming process. Decrease up to 10% of this electrical energy is expected when self-reducing agglomerates are used. This research aims to understand how the synergetic effects are when stronger reductant, like Fe-Si, is substituted for coke in self reducing pellets. Brazilian chromites containing 41.2%Cr2O3 were mixed with petroleum coke and agglomerated with cement as the binder. Small amounts of 1%, 2% and 4% of Fe-75%Si were substituted for the equivalent petroleum coke, and pure silica plus hydrated lime were added for adjusting the slag composition. The mixture was pelletized, dried and submitted at 1773K up to complete the reactions. The results showed that the reduction reactions were 1.4 and 2 times faster with 1% and 2%Fe-Si addition, respectively, than with no addition. The microscopic analysis showed that it was formed a liquid phase, but the pellet did not collapse what indicates that the coalescence of the metallic phase depends on the dissolution of the pre-reduced particles of the chromites into slag.

Jan 1, 2008

By Donald R. Sadoway

Molten salt electrolysis is a proven technology for the extraction of metals -- all the world's primary aluminum is produced in this manner. The unique properties of molten salts, also make them excellent media in which to treat a variety of forms of waste. Of special .note in this regard is electrolysis in molten oxides, a .concept put forward by. the author, initially as a ."clean technology" for producing primary metal. However, in the context of waste treatment, electroly-sis in molten oxides is a process offering the prospect of changing the. valence of dissolved heavy metals while making pure oxygen gas as the main by-product .Laboratory tests conducted at a temperature of 1550°C on chromate sludge dissolved in an melt composed of Al2O3 and MgO have confirmed electrochemical production of oxygen on a carbon-free anode.

Jan 1, 1996

By W. Song, C. Richards, B. Q. Li

"This paper presents a two-phase flow numerical model for spouting gas-particle flow reactors used in chemical vapor deposition processes for manufacturing heart valves and other biomedical implants. The model is developed based on the Eulerian-Eulerian formulation of gas-particle flows, with the k-e engineering model modified with the presence of particles for the description of turbulent gas flows. In parallel with the numerical model development, physical models are set up, where the particle image velocimetry is used for visualizing the particle flows and spout shapes and heights and optical probes are used to measure the particle velocities. The numerical model predictions are compared reasonably well with the experimental measurements.IntroductionVarious biomedical implant components, such as bone joints, dental components and heart valves, are coated with bio-compatible thin films by chemical vapor deposition in particle-laden chemical reactors [l-5]. In these reactors fine particles are used as packing and supporting media. During the coating operation, these packed particles are fluidized by an upward gas jet from the nozzle, reach a certain height and fall back on the top of an annulus region. These recirculating particles are mainly for levitating the implant components (usually one or two in a reactor at one time) so that every portion of them is equally exposed to the gaseous atmosphere. An equal exposure is critical for forming a uniform, mechanically strong and corrosion-resistant coating on implants. Plant experience shows that the quality of the coating is directly related to a stream of operating parameters such as temperature, particle size and loading, and gas flow rates [6]. Optimization of these operating parameters for improved reactor performance depends crucially upon our fundamental understanding of the physics governing the gas-particle flow, heat, and mass transfer phenomena taking place in these reactors."

Jan 1, 2004

By P. R. Khangaonkar

The industry of tin ore mining, beneficiation and smelting gives rise to a number of waste products like the beneficiation plant wastes (called amang), tin smelting slags, refinery dross etc. Some of the wastes deserve treatment to obtain economically useful products or to recover the metal values. The paper describes studies conducted on two materials, viz., struverite-middling (struverite-magnetic tin), which is an intermediate product of beneficiation circuits of tin tailings, and tin-smelting slags. The struverite middling was studied for treatment by chlorination using carbon tetrachloride, so as to yield vapour products separable by convenient condensation. The treatment was also found to lead to a tin-rich product amenable for treatment by known hydrometallurgical routes. The tin smelting slag was studied by alkali-leaching so as to avoid any dissolution of iron and it was possible to obtain an iron-free product solution suitable for high purity tin recovery.

Jan 1, 1996

By Michael B. Tessieri

With the increasing environmental demands and higher fuel efficiency standards on auto manufacturers, the use of aluminum in automotive applications is expected to show significant growth for the balance of this decade. Cast and wrought aluminum usage is reviewed by auto part, and alloy family for the year 2000 automobile. The analysis addresses the effect of this increased volume on the recycling infrastructure and identifies issues and opportunities, which will face the recycling industry.

Jan 1, 1995

By Yuanbo Zhang, Bin Xu, Guanghui Li, Xiao Kang, Chen Liu, Tao Jiang

Iron-bearing dusts, containing valuable constituents such as Fe, CaO, MgO, C, etc., are generally utilized as raw material in iron ore sintering. However, the dusts characterized by low granulating and refractory performances always lead to negative effects on sintering indexes. As we know, the innovative process named composite agglomeration process (CAP) has a series of advantages compared to traditional sintering process (TSP). In CAP, part or all of the iron-bearing dusts is made into green pellets with 5-15mm in diameter, while the rest of iron-bearing dusts and all of the other fine ores is granulated after mixing with fuels, fluxes and return fines. Compared with TSP, CAP could increase the ratio of iron-bearing dusts from 5% to over 20%. Meanwhile, the yield, ISO tumbler index and productivity reached 75.82%, 65.13% and 1.531t·m-2·h -1, respectively.

Jan 1, 2015

By Cang Daqiang, Li Yu, Liu Xiaoming, Zong Yanbin

"Utilization of high-quality heat in melting slag is a great challenge for iron and steel industry. In the paper, a new method is put forward to concurrently utilize heat and slag by converting the melting slag directly into high valued materials, slag glass-ceramic. A glassceramic with a higher basicity of 0.7 than traditional basicity of 0.45 was prepared from steelmaking slag in order to utilize more hot melting slag. Effects of Alz03 on its crystallization processes were researched by XRF, DTA, XRD and SEM. Results show that Alz03 in glassceramic would have great effected on its property. When the Alz03 content ranges within 12%-15%, glass-ceramics with basicity of0.7 could reach the best performances. The change of dominant phase in glass ceramics from akermanite and wollastonite to akermanite and gehlenite would significantly degrade its mechanical property. An increase of Al2O3 content leads to a rise of the viscosity and crystallization activation energy of the glass, while results in increasing sintering temperature and crystallization temperature of glass, which contributed to its fully crystallization and densification process.IntroductionSteel slag is a by-product under a process of converting iron to steel at above 1600°C, and 0.1-0.15 ton molten steel slag would be discharged for producing per ton of steel in the process. The discharged steel slag at 1600°C has heat of 68 kgce/t. In 2012, China's steel output reached 716 million tons, and produces about 100 million tons of steel slag and 68,000 tee of heat in it [1,2]. But at present, utilization of both slag and its heat at 1600°C is a great challenge for iron and steel industry.Dry granulation of melting steel slag by air and then recovering the heat of the hot air are a traditional technology which have not yet been put into practice for very low heat conductivity of the slag and low efficient of heat exchange among the different processes [3,4]. Therefore, a new method for high efficient utilization of both steel slag and its high temperature sensible heat is put forward [5,6], which is on-line reducing and extracting iron from molten steel slag and then directly preparing glass-ceramic by use of the residual molten slag."

Jan 1, 2014

By Ali P. Gordon, James Williams

Joints gasketed with viscoelastic seals often receive an application of a secondary torque, i.e., retorque, in order to ensure joint tightness and proper sealing. The motivation of this study is to characterize and analytically model the load and deflection re-torque response of a single 25% glass-fiber reinforced polytetrafluorethylene (PTFE) gasket-bolted joint with serrated flange detail. The Burger-type viscoelastic modeling constants of the material are obtained through isolating the gasket from the bolt by performing a gasket creep test via a MTS electromechanical test frame. The re-load creep response is also investigated by re-loading the gasket after a period of initial creep to observe the response. The modeling constants obtained from the creep tests are used with a Burger-type viscoelastic model to predict the re-torque response of a single boltgasket test fixture in order to validate the ability of the model to simulate the re-torque response under various loading conditions and flange detail.

Jan 1, 2015