Search Documents

By Zenjiro Asaki, Teruo Tanabe

"To clarify the formation of light rare earth (R =Ce, Pr, Nd or Sm) -Fe compounds in the reduction-diffusion (RD) process, two kinds of experiments were carried out: (a) RD experiment in which briquettes composed of R oxide powder, Fe (particles or wire) and CaH2 were reacted, and (b) immersion experiment, where an Fe plate was immersed into R-Fe melt having the composition of Fe-side liquidus line in Fe crucible. The compound formation was examined by using XRD, SEM and EPMA. The formation rates of RzFe17 measured by the RD experiment were compared with those obtained by the immersion experiment. The growth rates of compounds obtained in the RD experiment for Pr-Fe and Nd-Fe systems were much lower than those obtained in the immersion experiment. This result was explained by the difference of the reduction rates of R oxides by Ca. The parabolic rate constants for the formation of RzFe17 were separated in two groups of (a) Pr-Fe and Nd-Fe systems and (b) Ce-Fe and Sm-Fe systems. This was discussed in connection with the difference of their crystal structures and the driving force of diffusion. The parabolic rate constants for the formation of compounds in Ce-Fe and Sm-Fe systems decreased in the order of RFez, RFe3 and RzFe17.IntroductionTo understand reaction behaviors in the production of rare earth (R) -iron intermetallic compounds, which have excellent magnetic properties, is very important from engineering point of view. And the reduction-diffusion (RD) process<O has recently attracted attention as one of the promising processes to economically produce R-related materials. A few fundamental studies on the compounds formation in the RD process have previously been reported. Qi, Hino and Yazawa(2) observed the formation of R(Nd, Sm)-Fe and R-Co compounds in the process from various view points. Song and Ogawa(3) measured the growth rates of Nd-Fe and Sm-Fe compounds by using Nd or Sm vapor supplied from Nd-Ca or Sm-Ca melts. The authors have also carried out fundamental studies (4)-(8) to clarify the rate and mechanism in the production of R-Fe intermetallic compounds."

Jan 1, 1998

By Zhenbo Zhao

The processes and equipment for INLRFH (Isothermal Normalizing by Utilizing the Residual Forged Heat) of alloy carburizing steel products are presented. It is shown that four key parameters: namely (I) cooling rate before isothermal normalizing, (IT) the lowest cooling temperature before isothermal normalizing, (111) isothermal normalizing temperature and (IV) isothermal normalizing time, should be controlled. The prediction and calculation of these parameters can be achieved on the basis of components treated and the technical requirements of the steel parts by an on-line expert system. The cost-reductions due to the energy savings resulting from implementing this system for automotive parts heat-treatment are most promising.

Jan 1, 1999

By Jun Sugiyama, Hiroyuki Sano, Toshiharu Fujisawa, Hideki Takeuchi, Chikabiuni Yamauchi

"The solid .state electrotransport (SSE) is one of the most promising methods for the elimination of gaseous impurities from chemically active metals, such as rare earth metals. . In the present work, the SSE process was applied for the oxygen removal from praseodymium. The SSE factors, such as effective valence, were measured under the various temperatures, electric field intensities and initial oxygen contents, and the effects of those conditions on the SSE process were discussed. Furthermore, the solubility of oxygen in .solid praseodyillium was also measured·, by using the SSE method and metal-oxide equilibrium method.IntroductionWhen a direct current is passed through a solid alloy, not only electrons but also solute atoms are transported as charge carriers toward the anode or cathode. This phenomenon is referred to as an electrotransport or electromigration. The solid state electrotransport (SSE) is the application technique, based on this principle, to the pUrification of the solid metallic materials.Rare earth metals are used for various functional materials, such as magnetic, optical or electronic materials, therefore their high purity metals are required [l ,2]. However, rare earth metals are chemically active and have a strong affinity with gaseous elements (e.g. oxygen, nitrogen, hydrogen and carbon). In many cases, eliminating operations of gaseous elements have not been always made commercially, because these impurity elements could not be eliminated by usual treatments applied to the purification of ·common metals. As an alternative method, authors have proposed the· application of the SSE process to the elimination of gaseous impurities from rare earth metals. Investigations have been carried out on the yttrium-oxygen and neodymium-oxygen systems and the results were already reported[3,4]."

Jan 1, 2000

By Ryosuke O. Suzuki

A new cell concept for calciothermic reduction is proposed in which the titanium dioxide instead of TiCl4 is used as the raw material for reduction, Metallic calcium is needed as the reductant of a thermochemicaily stable oxide, such as TiO2. CaCl2, is selected as the solvent of Ca and simultaneously as the solvent of CaO. The reduction system consists of a single cell where both the reduction reaction and the electrolytic reaction for recovery of reducing agent coexist in the same molten CaCl2 bath. A few mol%Ca dissolves in the melt and gives the media a strong reducing power. Sufficiently deoxidized metallic titanium deposits and forms a slightly sintered granular sponge. Both mechanisms of the halide flux deoxidation and the electrochemical deoxidation work efficiently for these fine precipitates, The reducing agent is in situ recovered by electrolysis of CaO because the molten CaCl2 he a relatively large solubility for CaO Some cell designs and modifications are proposed for industrial applications.

Jan 1, 2003

By J. D. Scott

The counter-current jarosite acid wash circuit presently in operation in the zinc plant produces a combined jarosite plus Pb/Ag residue which is discarded. Extensive pilot-scale testwork, and some past in-plant operational experience, has shown that the zinc plant can be easily reconfigured to produce two residues during periods of high silver feeds and/or prices. Plant.optimized circuit configurations are available for silver recovery to a Pb/Ag residue and are in use for the prevention of Pb/Ag-jarosite formation in both the neutral and high-acid leaching circuits. Silver in the zinc plant undergoes several changes in state as it proceeds through these circuits. The roaster calcine is ~3:1 silver sulfate: silver metal, with metallic silver mainly as micro-Inclusions In an aluminosilicate phase. In neutral leach residue, the majority is as silver sulfide or Pb/Ag/Zn-sulfide coatings on unroasted sphalerite grains, with minor Pb/Ag-jarosite and some residual metallic silver in unreacted alumina-silicate grains. In high-acid leach residue, silver occurs as Se-rich silver sulfide particles in sulfur/jarosite ball aggregates, as silver sulfate impregnations in silica-gel masses and in solid solution in Pb/K/Zn~jarosite. Silver concentrations in solution range from 20 to 60 ppb.

Jan 1, 1990

By Thomas E. Weyand

Prior to 1975, lead-based paints were commonly used in protecting steel structures. Because of the toxic effects of lead on human health and the environment, their use has been significantly reduced. However, problems with these paints persist when they are removed during normal maintenance by pneumatic blasting with mineral abrasives. Technologies are developed to contain the spent abrasive and paint during blasting operations. This paper reports on A study to identify beneficial reuses for the spent blasting material. Nine samples were gathered from different projects within Pennsylvania. The samples were thoroughly characterized with regard to composition, morphology, and EP and TCLP leach test performance. Potential reuse applications will be reviewed with regard to technical adequacy, economics, and environmental constraints.

Jan 1, 1992

By Thierry De Nys

A direct leaching process of sulphidic zinc-based concentrates in aqueous sulphuric acid solutions has been developed by the V.M. R & D Department. By a very accurate control of the oxidation potential of the leach solution, this process enables a separate recovery of the zinc, copper, silver, lead and sulphur of the concentrate and makes it extremely attractive for treating more complex ores. The iron, solubilized during leaching, is eliminated out of the zinc solution by means of the V.M. goethite process. Alternative flow sheets for a conventional zinc electrolysis plant are presented.

Jan 1, 1990

By Yanhui Liu, Xuewei Lv, Chenguang Bai

A thermodynamic model for determining the surface tension of molten slag by considering the surface tension and molar volume of the pure oxide component, and their ionic radii was extended to the slag bearing high TiO2 (varying from 80 to 67%) at 1973 K. The iso-surface tension curves for the FeO-TiO2-Ti2O3 ternary system at 1973 K are almost parallel to the FeOTi2O3 line. TiO2 plays a role of surface-active solute, and its surface-active effect is attenuating with increasing the TiO2 content. The iso-surface tension curve shifts away from the TiO2 corner, indicating that the surface tension of the ternary slag decreases along with the addition of SiO2. The reasons include the addition of SiO2 with lower surface tension and the decrease of the total ion moment at the surface. Both CaO and MgO can bring about that the iso-surface tension curve shifts towards the TiO2 corner, indicating that the surface tension of the ternary slag increases along with the addition of CaO or MgO. CaO has a more pronounced effect on increasing the surface tension of the ternary slag than MgO at an equimolar amount addition. The increase of the surface tension results from both the compositional change and the variation of the slag structure.

Jan 1, 2015

By Ricardo Melamed

Metallic mercury has been extensively used for gold recovery. Although the solubility and mobility of metallic mercury is low, this metal can undergo many transformations, leading to mercury contamination in humans. The complexity of Hg chemistry in the environment reflects its different possible oxidation states and species, with different physical-chemical properties. The interaction of Hg in the terrestrial system, as well as in the aquatic environment, is important to understand the mercury cycle. This paper reports data on the adsorption of Hg onto an Oxisol soil. Results show that the interaction of Hg(II) at the soil-solution interface depends strongly on ligand concentration in solution, which can affect Hg mobility. The presence of the chloride anion in solution increases the mobility of Hg(II) through the soil, due to a relative lower affmity of mercury chloride at the oxide surface. In the absence of chloride, Hg(II) form strong complexes with the surface, and its adsorption behaviour is similar to the adsorption of other hydrolizable cations.

Jan 1, 1996

By Orlando C. Rojas

The Potrerillos Smelter commissioned a new El Teniente converter in 1985. As a result of the use of this technology, the Peirce-Smith converters have been processing only high grade matte or white metal. These operational changes resulted in damages to the converter shells, excessive splashing and cold dope generation and very short refractory campaigns. The paper shows the modifications to the tuyere angle, mouth design changes and new techniques for mouth cleaning and gas handling. Operational results up to 1991 are also shown.

Jan 1, 1993

By Shijie Wang

In pressure oxidation leaching of copper anode slimes, than 65% of the tellurium is m&apos; cxtraoted during decopperizing. About l0- 15% of the selenium is also dissolved simultane¬ously by severe leach conditions. Current operation for the treatment of the leachate is to constantly recirculate the leach solution through a bed of copper turnings. The tellurium and sele¬nium are precipitated from the leach liquor as copper telluride and copper selenide and sepa¬rated from the solution by filtration. In order to improve the reaction efficiency and reduce the process cost, viz, minimize the copper addition, cut retention time, and reduce the energy consumption; a chemical reducing agent is studied and the cementation process tested in the laboratory. In this paper, the test results are presented and the process chemistry is discussed.

Jan 1, 2003

By Wei Yu, Tiejun Chun, Jian Pan, Deqing Zhu

In this paper, improving the pelletization of Brazilian hematite by adding a boron bearing additive was carried out, and the pelletization parameters were also optimized. The mechanism of boron bearing additive was revealed in the kinetics of crystal grain growth by using LEICA microscopy and its software to measure hematite grain growth. Good qualities of green balls are manufactured with drop numbers above 5.7 times/0.5m, compressive strength higher than 13 N/pellet and thermal shock temperature over 620? under the following conditions: 1.2wt% bentonite, 0.4wt% boron bearing additive, 7wt% moisture and pelletizing in disc for 15 min. When the green balls were preheated at 1000? for 8 min and fired at 1280? for 15 min, the compressive strength of the fired pellets containing boron bearing additive is about 3096 N/pellet, which is far beyond the standard requirement for good quality pellets. Compared to the fired pellets without adding any boron bearing additives, the compressive strength of fired pellets containing boron bearing additive is increased by 1225 N/pellet. It is revealed that adding boron additive into the hematite pellets help to form more liquid phases, lower the activation energy of the hematite grain growth by 135.2 kJ/mol and increase grain growth rate by 33.6%, leading to higher strength of fired pellets due to forming more coarse and dense recrystallized hematite and energy saving by firing at lower temperatures for shorten time.

Jan 1, 2011

By Luísa Maria Abrantes

Environmental control is becoming more and more stringent. As conventional processes for zinc production are pollutant routes, alternative methods have become an important subject of research. In this regard, the leaching processes have aroused a considerable interest, namely the electrochemically induced approach. The behaviour of zinc concentrate ore in the leaching processesses is influenced by several parameters. Chloride concentration and leaching solution pH, time and temperature of reaction were studied in order to evaluate their influence on the zinc recovery. The efficiency of the leaching process for zinc extraction is performed by factorial design. The experiments were carried out by 23 and 22 factorial designs of the factors. Results show that all factors, except for the time of reaction have a significant influence on the optimisation process, within each experimental region.

Jan 1, 2001

By Richard S. Kunter

Artech Recovery Systems, Inc has developed a low pressure and temperature? leach process called the "Cashman Process" to extract metals from arsenical flue dusts and residues and fix the arsenic in an environmentally stable form as ferric arsenate (scorodite). The process was pilot tested at Hazen Research in an integrated plant including continuous recycle from August 1989 to October 1989 during which several tons of flue dust were processed. Based on this pilot program, the process was deemed technically feasible and produced commercially salable products. Residues from this pilot program were subjected to a long-term stability test jointly designed by PTI environmental services and the USEPA. The process, its versatility, and the nature of the products is discussed in some detail.

Jan 1, 1992

By Jorge Alberto Soares Tenório, Victor Bridi Telles, Denise Crocce Romano Espinosa, Felipe Fardin Grillo, Vicente de Paulo Ferreira Marques Sobrinho, José Roberto de Oliveira

"This research aims to study the process of incorporation of the metal iron in electric arc furnace dust (EAFD), from a steel mill producing long steel by liquid iron in addition to the changing temperature of 1400 degree Celsius altering experimental conditions such as how to add the EAFD (as received and in the form of briquettes), the percentage of EAFD to be added (10, 20 and 30% of initial weight of sample pig iron) and the time of withdrawal of the sample of pig iron and slag (30 minutes after the addition of EAFD). Previously, the EAFD will be characterized using the following techniques: chemical analysis, particle size analysis, X-ray diffraction, scanning electron microscopy (SEM) and Energy Dispersive Spectroscopy (EDS) microanalysis. After characterization, the eletric arc furnace dust to be added to the bath of liquid iron, will be divided into 2 types: the first order of addition will be in the form ""as received"" from the plant and the second is through the agglomeration of EAFD in the form of briquettes. The achievement of fusion experiments in laboratory scale, will take place in a vertical tubular furnace with temperature control. The fusion experiments to assess the incorporation of the metal iron will use graphite crucibles. A flow of inert gas (argon) will be maintained inside the furnace during the experiments. It is expected that the results obtained at the end of the research allow the evaluation of the iron metal incorporation of eletric arc furnace dust in hot metal bath.IntroductionThe steel industry generates a variety of solid wastes, liquid effluents and gaseous emissions at various stages of processing. The electric furnace dust (EAFD), generated in electric arc furnaces, represents a major problem for their content of chemical elements such as zinc, iron, chromium, cadmium, among others, issued to the atmosphere during the manufacture of steel[1]."

Jan 1, 2012

By B. Erik Ydstie, Dimitrios I. Gerogiorgis, Sridhar S. Seetharaman

"Carbothermic production of aluminium is an important alternative to electrolytic processes and has in fact been identified several decades ago as a potentially feasible and profitable process. The cornerstone principle is to take advantage of the endothermic reduction reaction between carbon and alumina instead of resorting to extreme amounts of electric energy to ionize and reduce aluminium oxide to aluminium. Electric energy is necessary only for heating purposes.The present study focuses on constructing and solving a steady-state electrothermic model for obtaining the spatial distributions for electric potential, electric field intensity and temperature. The complex issues of reaction kinetics and multiphase flow are handled by an approximation and are not addressed at the present stage, due to the lack of complete validated models. Because of its inherent complexity, the reaction slag is considered a pseudohomogeneous layer.An electrothermic simulation encompasses important research challenges, due to the limited knowledge of thermophysical properties for high-temperature multi component molten slags. Therefore, thermophysical property modeling and a systematic compilation of published data is a necessary and major first step towards enhancing understanding of the process fundamentals. Models are obtained by analyzing measurement data from numerous literature references for the density, viscosity, thermal and electrical conductivity and specific heat capacity of the slag.The electric potential, field intensity and temperature distributions obtained reveal interesting maxima which indicate localized superheating and lead to important engineering conclusions. The temperature profile calculated will serve as the foundation for the flow problem solution. This computational study will form a basis for future research towards combining the scopes of microscale CFD modeling and mesoscale process modeling into a unified modeling approach."

Jan 1, 2001

By J. Alberto Vázquez M.

A sensor employing yttria-stabilized zirconia (YSZ) was used to determine the oxygen activity of molten copper at laboratory scale at temperatures of 1200° and 1300 dc. The reference electrode was a Ni-NiO mixture. The amount of the deoxidizing agent (CU3P) ranged from I to 3% of the mass of copper. Thermodynamic analysis of the Cu-O-P liquid system was carried out to predict the required deoxidizing agent and the final composition of the molten copper. Both results, calculated and experimental, show that the oxygen removal is more efficient at lower temperatures. The kinetics of the deoxidizing reaction is very fast in the first minutes of the treatment. A metalography analysis of rapid cooled samples show the oxygen and phosphorus distribution

Jan 1, 2003

By C. Ramasamy

The tariff reductions on imports, as a part of on-going liberalisation process in India, has fueled competition within and outside India and has, in turn provided an opportunity to reach global markets. This change calls for quality upgrades and cost-competitiveness without impairing the environment. In this context, gas based processes, contributing to improvement in quality and environment as well as processes where controls are applied when gases inimical to environment are involved, are discussed in a remelt/cast-house scenario. The impact of such processes on fabrication cost of sheet ingot is seen alongwith consumption and cost of materials and compared with a world class standard plant in North America.

Jan 1, 1996

By Yuanbo Zhang, Daoyuan Zhang, Youlian Zhou, Guanghui Li, Tao Jiang

"Modified humic acid (MHA) has been developed by Central South University (CSU) and authorized in China. It has been reported that MHA is an effective binder for oxidized pellets prepared from specularite concentrates. In this research, effects of MHA binder on roasting behaviors of the specularite pellets are studied. MHA is an organic binder, containing much carbon, hydrogen, oxygen, etc. During the roasting, MHA can provide some heat because of combustion of hydrocarbon, which is beneficial for the recrystallization of Fe2O3 in the specularite pellets at high temperature. Simultaneously, part of hematite particles within the pellets are firstly reduced to magnetite, then, magnetite is oxidized into secondary hematite, which obviously improves the roasting performance of specularite pellets.IntroductionOxidized pellets have been widely used in steel production as a kind of high quality burden for blast furnace ironmaking [1]. In recent years, production of oxidized pellets is developing very fast. Therefore, the supply of high quality magnetite concentrates, which is the most suitable for pellet production, becomes scarce. It is imperative to pursue new alternative materials for oxidized pellet production [2]. Specularite concentrates have attracted widespread attention due to the advantages of high total Fe grade and low impurity content. However, due to the poor ballability and firing performance, specularite has not yet been widely applied into pellet production [3, 4]."

Jan 1, 2012

By Huimin Lu, Lian Zhou, Panpan Wang

"For the low concentration C02 exhaust gas from coal-fired power plant, steel plant emission trapping and recycle problem, a pressure swing adsorption process was studied, using a porous imidazolate framework materials (ZIFs) as adsorbent, separating carbon dioxide from fuel gas mixture. In the carbon dioxide reduction condition by electrochemical method, using ionic liquids as electrolyte, the oxygen and carbon products could be obtained, including carbon nanotube, nano carbon fiber and amorphous carbon. At last, a new C02 collection, recycling and reuse technology was formed.IntroductionDuring the combustion of fossil fuel in coal-fired power plant or steel plant, large amount of carbon dioxide has continuously emitted into the atmosphere. The phenomenon has resulted in the melt of arctic glacier and the frequent emergence of abnormal climate. How to reduce the emission of carbon dioxide and protect human living environment has become a worldwide challenge. Recently, there are three routes to resolve this problem: The first one is to adjust the energy structure and develop new energy, such as solar, wind, hydrogen; the second one is to improve energy efficiency and avoid waste; the third one is to research capture and sequestration of carbon dioxide (CCS). But many researchers have come to realize that the recovery and utilization of carbon dioxide are more important than the sequestration of it. Because the captured carbon dioxide just buried under the earth maybe cause secondary pollution if carbon dioxide leak out from the adsorbent."

Jan 1, 2013