Search Documents

By Jitka Jandová

A laboratory process based on simple and environmental friendly operation, aimed at recycling of spent Li/MnO2 batteries, is described in this study. This process involves roasting Li/MnO2 batteries in a vacuum furnace at 650°C, followed by selective leaching Li2CO3 from calcined electrode material in distilled water at ambient temperature and controlled crystallization of pure Li2CO3.

Jan 1, 2006

By Kee Jeung Lee

In this study the characteristic factors and formation mechanisms for the hydrothermal preparation of a -quartz crystal powders were investigated to find the optimum synthetic conditions. The degree of Q -quartz crystal face development depended on the relative growth rate of a particular form that varies considerably with the degree of supersaturation, the reaction temperature, the concentration of mineralizers, and the presence of seed crystals in the feedstock. Alkali hydroxides and alkali halides were found to be effective in the reactions as mineralizers, which added in order to increase the solubility of the feedstock. The fine Q -quartz crystal powders were obtained in the temperature range of 250-450% and pressure range of 100-300atm. As the concentration of mineralizers increased, the particle size of crystalline powders became smaller at lower reaction temperatures. The fractional size distribution of synthetic crystal powders was depended on the hydrothermal conditions. As the reaction time and the amount of seed crystals increased, the width of particle size distribution became narrower. The weight mean particle size was in the range of 1 to 10m. The characterization of the products were carried out using XRD. SEM. PSA, FT-IR, Raman spectrometer.

Jan 1, 1997

By Linping Yu

A simplified ED process was developed for organic acids recovery from cyclohexanone waste in this paper. In this regard, the one-stage ED was investigated directly without pretreatment, such as ion-exchange or nanofiltration to removal of foulants. The current efficiency and the energy consumption in the ED process for the recovery of carboxylic acids from cyclohexanone waste is theoretically analyzed and experimentally tested. The concentration of recovered carboxylic acid is related to many parameters and still needs more work to be determined.

Jan 1, 2009

By Noritaka Horii, Katsuyoshi Kakinuma, Hiroshi Yamamura

"ZrO2 and Y2O 3-doped ZrO2 gel film were obtained by spin coating of sol from Zr-n-propoxide, n-propanol, acetylacetone, nitric acid, and water on a silica glass as a substrate. ·Dried gel films crystallized to monoclinic, tetragonal, cubic and their mixed phases, depending on the chemical composition of sol, .firing temperature, and coating cycles. ZrO2 films with highly preferential orientation were successfully obtained from a solution containing a large amount of n-propanol. The highly oriented ZrO2 film was found to have high transparency compared with non-oriented 'films. Electrical conductivity of 8 mol% Y2O 3 doped ZrO2 film was also measured.Introduction3 mol% Y2O 3 doped ZrO2, which has a tetragonal symmetry is ·well known to have a strong mechanical property and a high toughness. (1) On the other hand, 8 mol % Y 2O 3-doped ZrO2 is high oxide-ion conducting material and is applied to oxygen sensor, oxygen pump, and solid oxide fuel cell (SOFC). (2) Sol-gel methods using metallic alkoxide are widely applied for synthesizing ceramics such as high-purity fine particles, thin film, and fiber. (3) For ceramics films, many reports have been made on SiO2, (4) TiO2, (5) and PZT. (6) Several case studies have been done on zirconia film based on the sol-gel method, (7) - (11) but very few on preferentially oriented film and on systematic Y zO3 doping. Almost zirconia ceramic· films reported were prepared by means of dip-coating. Kamiya et al. (12) and Ganguli et al (13) converted zirconia into fiber. Sol from Zr alkoxide is usually very unstable, and a stabilizing agent such as glycol or ß-keton is used beforehand (7) (14)."

Jan 1, 2000

By C. Frias, M. Garcia, G. Diaz

Advances in hydrometallurgy promoted by Tecnicas Reunidas are providing increasingly simple and clean means for controlling the entire lead recycling chain. Used in parallel with pyrometallurgy, these processes allow furnace temperatures to be reduced and fumes and atmospheric pollution to be minimised. Furnace slags are digested, and residues (mainly gypsum) are non-toxic and convertible into marketable products. In addition, the global economy of the process is substantially improved by reducing the operating cost, increasing the lead recovery above 99% and obtaining a 99.99% pure lead product. These new PLACID and PLINT processes may provide the cleanest and healthiest practicable means for recycling lead from batteries.

Jan 1, 2000

By Zviad Kovziridze

It is stated that the specific character of SPHTS specimens of TiCx consists in crystal lattice strength reflecting the condition of synthesis in ?burning wave?. The use of roentgenographic and other methods of analysis allow to estimate the effect of the conditions of synthesis causing the carbon sablattice defect on the grinding intensity of TiCx -phases. The study of the kinetics of vibratory grinding of TiCx -phases in ethanol and benzene medium allows to establish high grinding intensity of the phases close to stoichiometry and the possibility of producing high dispersion powders (Ssp 4.5-6 m2/g).

Jan 1, 2006

By Milind Deo, Neale R. Neelameggham

The mixture of carbon dioxide and water vapor - called Soda [as in carbonated water] can be converted to easily stored transportation fuels. Earlier papers on Soda- fuel metallurgy noted that this conversion is endothermic requiring energy. Reduced state metallic elements - preferably the alkali, alkaline earth elements, or aluminum can act as oxygen carriers. Availability of such a combination in commonly land fille waste materials is shown. Plant based wastes which are normally composted form a better-controlled reagent. The energy required for the reaction can come from solar energy. This paper describes possible reactor designs, which can accommodate this conversion effectively using carbon dioxide recovered from flue gases.

Jan 1, 2008

By David A. Army

Many times, the maintenance professionals have been involved in changes to processes or systems. Often they rely on seat of the pants knowledge to determine whether or not they were successful. More often than not, once our attention has been turned to other endeavors, the initiative has floundered. This paper will describe those measures that can be most effectively used to track and manage the success of implementing an improved Work Management System. However, not only will the paper discuss traditional work indicators, it will also explain how to establish the behaviors in the work place that will ultimately ensure successful implementation. Combined with the discussion on indicators will be a discussion on how to tie them to bottom line results and display them in the form of a scorecard. Actual results will be discussed.

Jan 1, 2006

By Jun-ichiro Yagi

A mathematical model has been developed for simulating the blast furnace operation with carbon composite agglomerates charging based on multi-fluid theory and reaction kinetics. In this model, the behaviours of carbon composite agglomerates are considered on the basis of previously reported conservation equations and experimental research on the reduction rate of carbon composite agglomerates. A series of calculations are performed to examine the effect of charging carbon composite agglomerates. The model calculation gives two-dimensional distributions of process variables and information on the overall operational parameters. It reveals that in-furnace temperature levels significantly decrease and the reduction of carbon composite agglomerates is retarded with carbon composite agglomerates charging ratio. The furnace performance is remarkably improved with the increase in carbon composite agglomerates rate. The productivity tends to increase while coke rate and total reducing agent rate show decreases at the different degree.

Jan 1, 2006

By S. Subhawong

Following the startup of the zinc plant in Clarksville, Tennessee, in 1978, the original effluent treatment plant did not perform as designed. The sludge, produced in a conventional lime neutralization treatment, settled poorly and began to fill the permitted lined impoundment within two years, well short of the original design capacity. Another sludge pond had to be constructed. This led to a new process modification of the original design. Although the design is still based on the conventional lime precipitation of heavy metals, the current effluent treatment plant has evolved into a hydrometallurgical circuit, capable of producing good quality water without generating sludge. Undesirable elements are bled from the zinc circuit and are rejected through the effluent treatment operations. Wallboard grade gypsum is produced, instead of sludge, and all the gypsum is sold to cement and wallboard plants. This operation also recovers and returns more than 1,500 tonnes of zinc annually to the 105,000 tonne/y zinc plant.

Jan 1, 2000

By Scott Shuey

The processing of post-consumer materials is an area being addressed by many industries and multiple engineering disciplines. While metal scrap and high-value uniform waste streams tend to find their way back to their respective parent processes, the more complex and low-cost ubiquitous materials, such as Polyvinalchloride (PVC) and Polytetrafluorethane (PTFE), tend to show up in many processing streams. From a metallurgical perspective, pyrometallurgical processing of a mixed metal/organic/oxide waste material allows for the recovery of thermal energy in conjunction with the recovery of metal values. The evolution of halogenic acids during elevated temperature processing can create complications with both the materials of construction of the processing equipment as well as gas stream processing. The need for dust collection coupled with a high acid content, necessitation high-volume scrubbing, increases the costs associated with gas handling. Control of the halides through entrapment as a solid in-situ during processing would simplify downstream processing. Alkali-halide complexes are being evaluated by researchers at CSM for mixed metal/polymer waste material treatment, recovering halogens as salt complexes.

Jan 1, 2006

By A. Bruynesteyn

It is well known that most North American gold deposits are of a hydrothermal origin and therefore they are often associated with sulphide minerals such as pyrite and arsenopyrite. When the precious metals in such ores are held captive inside sulphide crystals, the ores are called refractory because they do not respond to treatment by direct cyanidation. In these cases, it is necessary to recover the contained precious metals using high temperature treatments such as smelting or roasting, or high pressure leaching processes to break down the sulphide crystal matrices and thus liberate the precious metals for subsequent extraction by cyanidation. Sulphidic gold ores containing arsenic and/or antimony are considerably more difficult to treat because, in addition to their refractory nature, the arsenic and antimony content also prohibits treatment by direct cyanidation or amalgamation. These ores must be milled and their sulphidic gold values concentrated by flotation. The resultant concentrates must then be roasted to break down the sulphides before cyanide treatment can be applied.

Jan 1, 1985

By J. A. Voigt

In an effort to determine the optimum conditions for preparing high purity, fine particle size high temperature superconducting oxide powder, we have investigated how calcination conditions influence the conversion of a chemically prepared hydroxycarbonate precursor powder to YBa2Cu307. We find that the precursor can be converted to phase pure YBa2Cu307 in either oxygen or synthetic air (20% 02. 80% N2) at 850°C. This temperature is substantially lower than the temperature (>900°C) normally used for the calcination of mixed-oxide powders. The lower calcination temperature prevents particle sintering and maintains the desired fine particle size. Powder processed in synthetic air shows a low degree of crystallinity indicating it may be more sinterable than the highly crystalline powders produced when an oxygen atmosphere is used. Intimate contact between powder particle surfaces and a flowing gas atmosphere promotes the reaction between the BaCO3 component of the precursor powder and the Y and Cu constituents.

Jan 1, 1989

By Yiming Rong, Gang Wang

"Water quenching is one of common heat treatment processes but with complex physical phenomenon, in which vaporizing, bubbling and convection are involved. The general simulation of liquid quenching processes is conducted by using temperature dependent value of heat transfer coefficient (HTC) obtained from experimental measurement under a strong assumption. A preliminary multiphase flow model developed by using Ansys-CFX for water quenching has been presented in this paper, which shows a distributed HTC with a time dependent feature. The conjugate heat transfer is used to describe thermal conduction in the simplified workpiece, and generation, growth and flow of bubbles are modeled by using Eulerian-Eulerian method for the gas-liquid multiphase flow. The simulation result shows the intense variation of heat exchange through the interface between workpiece and liquid, and the unsteady distribution around the solid surface.IntroductionQuenching is a rapid cooling process which makes the desired solid phase transformations happen for the certain material properties. For aluminum alloy, rapid quenching will prevent all phase transformation and generate a supersaturated single phase."

Jan 1, 2012

By J. H. Lee

LG Metals Corporation started its second smelter operation at Onsan along with the existing flash smelter on January 31, 1998. Onsan smelter has been producing about 140,000 tons of copper annually from concentrates with the flash smelting line since 1979. In accordance with an increase in domestic copper demand, LG Metals Corporation decided to expand smelting and refining capacity by introducing a second smelter line using the Mitsubishi continuous process and a new tankhouse in 1995. After two years' expansion works consisting of engineering, procurement, construction and a successful commissioning test, the total smelting capacity of Onsan smelter increased to 340,000 ton of copper annually from concentrates. This paper describes the smelting facilities, operation result, problems encountered and improvements during the start-up and early operation of Onsan's new smelter

Jan 1, 1999

By Valeriano Antonio Corbellini, Marilda Macagnan, Rosana de Cassia de Souza Schneider, Tiago Bjerk, Mariela de Souza Vieira

The great potential of Brazil for the agricultural production makes our country a generator of agro industrial residues. In this context, the solid-state fermentation appears as a technology that shows alternative ways for those residues, adding values to these raw materials, through the production of substances of industrial interest, besides reducing the possible environmental problems. The main objective of this study was to apply the bovine fat residue associated to the garden grass for the fungal lipase production. Initially, 75 microbial cultures were isolated from garden grass samples after incubation of the mixture with bovine fat. From these cultures were selected the filamentous fungi, whose lipase production abilities were evaluated. The isolation and the selection were accomplished by using a differential culture medium containing Tween 80 as inducer substrate of lipase production. The colonies with lipolytic potential were detected by the presence of white precipitation haloes on the agar. With agro industrial residues the best lipase producer fungus was identified as Penicillium sp in 6 days of solid state fermentation. The crude enzyme obtained was tested in transesterification process for the biodiesel production.

Jan 1, 2008

By K. Th. Mavrommatis

Cleanness of steel is justified, measured and estimated in steelmaking process through different concepts which are mainly based on operational, empirical or semiempirical parameters and describe ?cleanness as a state?. In this work a theoretical concept is developed, considering ?cleanness as a process? and introducing a dynamic aspect into the quantification of cleanness of a steel melt, linking operational parameters with physicochemical variables, which are based on first principles. This concept and the here derived and developed variables and parameters are based on the earlier defined agglomeration index (AI) of a steel melt, the ratio of the mean inclusions diameter (MID) to the mean inter-particle distance (MIPD), which is shown to be a measure of the agglomeration tendency of the melt after deoxidation, and can serve both, to monitoring cleanness during steelmaking operation and to be useful as a basis for mathematical modelling of cleanness and of the metallurgical measures in plant, associated with production of clean steels.

Jan 1, 2006

By Chu Bo-Yi

"This paper contains a comparison of creep-feed and shallow-cut grinding on ceramics with both neat oil and water-based grinding fluids. When a water-based grinding fluid was used in creep-feed grinding on ceramics the vertical forces and specific energies increased markedly fast with result that the wheel surface was damaged seriously. Creep-feed grinding on ceramics with neat oil not only produced much lower grinding forces and specific energies but also resulted in the wheel remaining in good condition and minimizing damage to the ground surface. This finding may lead to a deeper understanding of the behaviors of grinding fluids in grinding processes both on ceramics and metal as well.1. IntroductionAs advanced ceramics are obtaining more and more applications in the technical area, some machining processes are needed after the sintering to reach the accuracy and finish required by components. Because of higher hardness and brittle behaviors of modem ceramic many researches have been done in order to improve grinding efficiency and surface quality.In the grinding metals the concept of creep-feed grinding has been developed in industry as a real alternative to the normal method of shallow-cut grinding. In addition to the general economic advantages, dimensional accuracy and surface integrity are invariable improved using the creep-feed grinding technique.In grinding ceramics former studies have done many works on both creep-feed and shallow-cut grinding on ceramics with water-based grinding fluids since the water-based were thought to be better coolants than neat oil in most tests of grinding metals[l]. It was suggested that the specific grinding energies of ceramics are markedly higher in creep-feed grinding. The grinding force increases vary rapidly with time in the creep-feed case. In other words, so-called speed stroke grinding with high workpiece speed is considered more suitable for improving the grinding efficiency [2][3]."

Jan 1, 1998

By M. A. S. Siraa

A program of work was undertaken at the Kennecott Smelter and Refinery to model the complex. This effort contributed a total of eight models of the plant: flash smelting furnace, flash converting furnace, slag concentrator, anode furnace, offgas scrubbing system, acid plant, hydrometallurgical dust treatment plant, and the precious metals plant. Some of these models have been used in a variety of investigations ranging from offgas capacities for a steam generation analysis to an examination of impurities. The culmination of this enterprise has resulted in an on-line control scheme for the flash smelting and flash converting furnaces. These two process control schemes incorporate their respective steady-state heat and mass balances that are executed in response to feed changes while a feedback loop calculates when product grade and temperatures deviate from setpoints. This system has been put into place to improve furnace control and on- line time.

Jan 1, 1999

By Eustathios S. Kikkinides

This work presents an integrated approach for the optimal design and control of hydrogen storage beds. A detailed 2-D mathematical model is developed for metal hydride beds and validated against experimental and theoretical literature results. Based on recent advances in dynamic optimization, the model is used to find the optimal process design and operating strategy in order to minimize the storing time, while satisfying, a number of operating constraints (such as pressure drop limitations, cooling fluid availability and maximum tank temperature). Trade-offs between various objectives, alternative design options and optimal cooling control policies are revealed illustrating the potential of the approach. In a further step the model is used to exploit the benefits between material and process design. Systematic simulation and optimization studies are performed at two different length scales (tank and adsorbent pore level) for carbon based materials. The macroscopic approach determines the optimal values of the sorption parameters while, based on these results molecular simulation techniques are employed to determine the pore size distribution of the adsorbents.

Jan 1, 2006