Search Documents

By Yavuz Ali Topkaya, Aydin Rusen

"In this study, zinc and lead recovery from zinc plant leach residue obtained from Çinkur using hydrometallurgical methods have been investigated by laboratory scale experiments. Considering more than one million tons leach residue (LR) rich in Zn (12.43%) and Pb (15.51%) in the stockyard and environmentally hazardous, it is essentially necessary to process Çinkur LR. Zinc and lead have been recovered in two main stages. As a first step, Çinkur LR was releached by using hot sulphuric acid for zinc recovery. About 72 % Zn was recovered by using 150 g/l H2SO4 at 95 oC in 2 hours with a pulp density of 200 g/l. Secondly, for lead recovery brine (NaCl) leaching tests were performed on the secondary Çinkur LR obtained after acid leaching process. In brine leaching while lead recoveries up to 95 % could be attained at a low pulp density, the maximum recovery obtained was 84.9 % at a high pulp density (200 g/l) with 300 g/l NaCl concentration in 10 minutes at 95 oC. Introduction Zinc and lead have been known and used by humans since ancient times and also they are important nonferrous metals [1]. Zinc and lead have different properties thus they are used in various application areas, ranging from automobiles to construction, from batteries to textile. Zinc and lead deposits are widely distributed in the Earth’s crust. The principal ore mineral for zinc is zinc sulfide, Sphalerite (ZnS), and lead sulphide, Galena (PbS), is the main source of lead in the world [2].Although zinc is generally produced from sulphidic ores (ZnS) or concentrates by Roast – Leach – Electrowinning (RLE) in the world, in Turkey, zinc production is based on zinc carbonate ores (ZnCO3), and at the Çinkur plant zinc was produced from zinc carbonate from its establishment to 1997 due to high reserves of zinc carbonate in that region. Çinkur is the only plant in Turkey that produces Zn from primary ore containing ZnCO3 by Waelz – Leach - Electrowinning route [3]. However, due to depletion of local high grade ores, oxidized ore concentrates were imported from Iran after 1997, until this plant was shut down. Therefore, there are two different leach residues (LR) which are Turkish LR (TLR) and Iranian LR (ILR) in Çinkur stockpiles. It has been estimated that the total amount of leach residue is more than one million tons of which the major part is Turkish leach residue (TLR)."

Jan 1, 2008

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By Nicola Baldo, Marco Pasetto

"The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, in order to verify the possibility to use different types of electric arc furnace (EAF) steel slags – in substitution of the natural aggregates – in the composition of both dense graded and porous asphalt mixes for flexible road pavements. The research has been articulated in a preliminary study of the chemical, physical, and mechanical properties of the EAF steel slags, and in the following mix design and performance characterization of the bituminous concretes, through stiffness modulus tests at various temperatures and permanent deformation (creep) tests. All the mixtures with EAF slags have satisfied the requisites for acceptance standardized for the road sector, thus resulting as suitable for use in the construction of infrastructures, moreover presenting higher mechanical characteristics than those of the corresponding asphalts with full natural aggregate. IntroductionSteel is produced industrially employing two main technologies: the integral cycle, which starts from mineral iron, and the electric cycle, which uses scrap metal. A consistent amount of the steel produced in Italy (approx. 55%) comes from Electric Arc Furnaces (EAF), which every year, alongside the steel, produce approximately 2 million tons of slag. The recycling of this waste product to produce new high-quality raw materials would reduce both the exploitation of limited natural resources and the amounts of refuse. In the European Union, 60% of slag from EAF is still today disposed of in dumps. The extremely diverse origins of scrap metal (waste from mechanical manufacturing, industrial and civil demolition, car bodywork, etc.) means that the by-products generated by the smelting, slags and ashes, contain different elements, in varying composition, also depending on the type of steel to be produced and the consequent adding of binding and melting elements during the production process. For this reason, iron and steel industry electric furnace slag - unlike the blast furnace dross utilised in cement works, which has a more uniform composition as it comes from a more standardised cycle – has been viewed in the past with some diffidence and so, at least in Italy, the possibilities of its re-use have never been fully developed."

Jan 1, 2008

By Vahid Rastegar

"Characterization of the microstructure and revealing dendrites in the microstructure and also measuring the dendrites arm spacing and the distribution of silicon were studied in various pieces of compacted graphite cast irons with 0.17, 0.185, 0.2, 0.22 and 0.24 percent of mischmetal. Black-white and color metallography (quantitative and qualitative) were carried out on the various steps of the cast samples. Distribution of silicon was studied quantitatively using spot analysis with scanning electron microscopy. Furthermore, effects of two variables (cooling rate and mischmetal percentage) on dendrites arm spacing were investigated.In order to color metallography, the samples were plunged into a boiling solution of 18% KOH, 9% NaOH and 9% picric acid in distilled water. It was inferred that the microstructure coloration varies according to the sequence: green-->red-->yellow-->blue-->dark brown->light brown as the silicon content decreases. After observing dendrites, dendrites arm spacing was measured. In this method, it seems to be possible to predict the mechanical properties of compacted graphite cast irons by knowing dendrites arm spacing and without any destructive testing. After studying the two variables, it was concluded that dendrites arm spacing decreases as the amount of mischmetal increases and it increases as the cooling rate increases.IntroductionIn general, detecting of primary austenite dendrites is not possible in cast irons due to their solidification system. Observing the dendrites in the room temperature is possible only in those gray cast irons that contain type D graphite. With collecting data of dendrites arm spacing (DAS) measurements, it could be possible to achieve the mechanical properties of cast irons without any destructive testing. In this research by applying a particular method, primary austenite dendrites and also distribution of silicon in the microstructure has been observed."

Jan 1, 2012

By Wellington Pereira Inácio, Frederico Muylaert Margem, Artur Camposo Pereira, Sergio Neves

"Natural fibers are currently gaining attention as reinforcement of polymer composites for uses in engineering parts for automobile and building construction. In spite of environmental, economical and societal advantages, the natural lignocellulosic fibers are not as uniform in their dimension and properties as compared to synthetic. In recent works it was found that the variation in strength could be correlate to the equivalent diameters for several lignocellulosic fibers including the sisal fibers. In the present work an investigation on a possible correlation of the equivalent diameter with changes in density and elastic modulus was carried out. Precise measurements of the equivalent diameter, conducted in a profile projector, were correlated with the density and the elastic modulus by means of the Weibull statistic analysis. The results showed that an inverse correlation with the diameter also applies for both the density and the elastic modulus with a high degree of precision. SEM observation of the sisal fiber in structure and fracture aspects strongly indicate that defects and microfibril participation could be responsible for the inverse correlation.IntroductionAccording to Kalia [1], cellulose-based fibers are currently being pushed owing to their ""green"" image. Contrary to synthetic glass fiber, extensively used in our modem technology, these lignocellulosic fibers are renewable and can be incinerated at the end of the material's lifetime without adding pollution in the atmosphere moreover, the amount of CO2 released during incineration process is negligible as compared to the corresponding amount taken up by the plant throughout its lifetime. Even if an industrial processing equivalent of C02 release is added, the lignocellulosic fiber is considered neutral with respect to the emission of gases responsible for the global warming [2]."

Jan 1, 2012

By B. Holleis, M. Potesser, D. Spoljaric, H. Antrekowitsch, A. Hengelmolen

"During the past only an optimization of metallurgical furnaces were done without attention on the burners. Nevertheless, furnaces without burners are impossible to use in the primary and secondary nonferrous metallurgy in an economic way. Since the energy cost is increasing and the environmental protection is becoming a global issue, the burners are in the focus of several investigations and optimizations. One possible way is the combustion by oxygen. By using oxygen, the flame temperature increases and therefore, fuel accordingly money could be saved by having a low amount of harmful substances like NOx in the off gas. This paper describes a new burner system which combusts fuel with oxygen or air by diluted combustion, hence low pollutants in the off gas. Furthermore the effectiveness of the burner characterized by off gas analyses and simulation in the new development chamber, but also practical tests at an aluminum smelter are described.IntroductionIn 2005, Messer Group established a technology competence centre for metallurgy in Gumpoldskirchen (Austria), with the aim to develop oxygen burners which satisfy today’s and upcoming standards of legislation as well as customer requirements. With the assistance of the Development Sponsorship Fund (FFF) of Austria, cooperation with the University of Leoben was agreed on. With the long term experience of the Gas-Wärme-Institut “GWI” in Essen (Germany) and the University of Leoben, different new burners have been developed."

Jan 1, 2008

By S. Kawamura, H. Inoue, Y. Maeda, H. Ohike

Kosaka smelter is a copper smelter located in Akita Prefecture in the northern part of Japan. It has treated complex sulfide concentrates for a long time. Recently, in addition to metal production from ores, the company has been working on the recycling of metals by using this metallurgical technology. Metals recovered are primarily gold, silver, palladium, copper and lead from copper scraps, electronic board scraps, silver oxide batteries, spent lead acid batteries, semiconductor chips, cellular phones, and automotive emissions catalyst. In particular, electronic board scraps and cellular phones can be valuable raw materials. These electronic scraps are fed into the flash smelting furnace after size reduction in a shredder that was introduced in 1999. Due to the growing demand for personal computers and cellular phones, the amount of electronic board scraps available for recycling increased. At present, these secondary materials are good raw materials for Kosaka smelter since the smelter is already used to dealing with complex raw materials. The recycled metals account for up between 5 and 20 percent of the total production at Kosaka Smelter. In particular, over 90 percent of the palladium in the secondary materials can be recovered.

Jan 1, 2000

By Fu-Shen Zhang, Mengjun Chen, Jianxin Zhu

"In China, hazardous e-waste—cathode ray tube (CRT) glass is usually left around, and it is likely to contact with water resources directly. To identify the real leaching characteristics and bioavailabilities of heavy metals Pb and Ba contained in CRT glass in the nature environment, experiments were carried out by simulating the nature environment. The results indicated that Pb and Ba contained in CRT glass were stable in most conditions, which only showed obvious leaching toxicities in strong acidic/alkali conditions. EDTA and DTPA extractable Pb and Ba amounts were extremely high, e.g., EDTA extractable Pb of color funnel glass was up to 1960.07 ìg/kg, indicating that the potential bioavailability of waste CRT glass is very high. IntroductionIn recent years, cathode ray tube (CRT) contained monitors or TV sets has been substituted by novel and better electronic and electric equipments such as LCD and PDP, leaving huge amounts of end-of-life CRTs. 50~85% of the total weight of a computer monitor or a TV set is glass'1-21, which was classified to three categories: black & white glass (BW), color panel glass (CP) and color funnel glass (CF), according to their chemical compositions'3' (Méar et ai, 2006). In order to provide shielding from X-rays generated during the picture projection process, lead, barium and strontium oxides were used in the glass. In general, a color CRT contains 1.6-3.2 kg of lead'4'. Concerning the high toxicity of lead, these waste glasses have posed a potential risk to the environment and human health and researches on these glasses have been attracting wide and tense attention currently."

Jan 1, 2011

By Takeshita. Takuo

"In this work, the progress of the HDDR process is discussed mainly on the Nd-Fe-B magnet system. There are three technologies being used for the Nd-Fe-B permanent magnet production; the sintering technique, the rapid quenching annealing and the HDDR process. The HDDR process utilizes· the HDDR phenomenon, in which hydrogen absorbing intermetallic compounds go through as they are heated in hydrogen atmosphere, Hydrogenation - Decomposition Desorption - Recombination. In the HDDR process, these four steps in the HDDR phenomenon are processed by choosing suitable reaction conditions regarding to hydrogen gas pressure, temperature, rate ·of desorption and etc., and we can produce permanent magnet powders of good magnetic properties with microstructures consisting with sub-micron size crystalline grains. In the anisotropic magnet powders, the sub-micron size crystals are being mostly aligned in the crystallographic c-axis direction. Possible applications of the HDDR process to other systems are also discussed.Microstructures of the Nd-Fe-B Permanent MagnetsIt is well known that magnet properties of magnetic materials are very sensitive to their microstructures [l]. This is seen in almost all magnet materials from soft magnetic materials and hard magnetic materials to magnetic memory materials. In this regard, the production technology is very important for the control of microstructures of permanent magnets The Nd-Fe-B magnet is the most powerful permanent magnet as a practical permanent magnet, and its coercivity force is much dependant on the microstructure as is the case for other permanent magnets."

Jan 1, 2000

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Leandro Voisin

A new pyrometallurgical treatment alternative is proposed for cleaning complex copper matte with high content of impurities in the copper smelting process, thus, in a suitable furnace, a given amount of pig iron will be added to the liquid complex matte with a matte grade between 65 and 75 % Cu under reducing condition and will produce three liquid phases of matte, copper-rich alloy and iron-rich alloy. Hence, in this study, firstly, a mass balance calculation was made on the basis of the reported data for the distribution ratios of the components among the three phases to define the optimum condition where most of the arsenic can be fixed in the less valuable liquid iron-rich alloy. By taking advantage of the high concentration of arsenic in the iron-rich alloy, the small volume alloy may be disposed in a yard, while the precious elements may be recovered effectively in the liquid copper-rich alloy and/or in the liquid matte. Secondly, laboratory-scale experiments were conducted to apply the proposed process to the matte produced from the slag-cleaning electrical furnace and the Teniente Converter of the Codelco-Norte smelter. The obtained results indicate that the proposed process for cleaning complex matte is promising.

Jan 1, 2006

By Ledjane Barreto, Tulio Flávio Accioly de Lima e Moura, Wilson Acchar, Antonio Carlos Silva da Costal

"Clays are common ingredients in pharmaceutical products both as exclplents and active substances. Clay minerals are naturally cationic exchangers and they may undergo ion exchange with basic drugs in solution. Smectites, and montmorillonite have been studied due their high cation exchange capacity as compared to other silicates. Recently a patented study reports the use of attapulgite as the encapsulating agents both for the protecting the active substance and modulating release into the body. Some clays such as kaolinite, smectites, talc, etc are also used as dermatological protectors. Sepiolite and smectites have the ability to form complexes with organic compounds with absorb ultra-violet radiation, enabling them to be used in sun screens with protection factors. The objective of this work is to characterize the attapulgite in order to study the potential use of this clay material in the human health.IntroductionSince the begimling of time, nature has served humanity as a source of various raw materials. Among these, clays such as kaolinite and ilitte are common ingredients in the tile production. Recently, special clay materials have been investigated in order to identifY new potential uses of these class of materials. Clay materials are natural raw material and have excellent properties such as low toxicity, good biocompatibility, making them a good material to be used in biological applications. Attapulgite (paligorskite) and sepiolite is so called special clays. These special clay materials are very sin1ilar and have a great potential to be used in some technological areas due their special catalytic, sorptive and colloidal-rheological properties [1-8]. Recently some works have reported the use of these special clays materials for many applications such as drug delivery, wound dressing, oil absorbent, pesticides, fertilizers [9-12]. Brazil has a significant reserve of attapulgite located in Piaui state, making the study of the potential of this mineral in special areas, very attractive. Attapulgite is classified a fibrous alluminous silicate material and shows the presence of micro pores and channels, fine particle size and high surface area making this material a good candidate alternative material to be used in many industrial applications [6,8,9,11,12]. The objective of this work is to characterize the physical and microstructure of attapulgite."

Jan 1, 2012

By Lucas Barbosa de Souza Martins, Frederico Muylaert Margem, Nathalia Carneiro Garcia Rosa, Sergio Neves Monteiro

"A natural banana fiber extracted from the plant pseudostem has shown values of density and mechanical strength with potential for uses in engineering applications such as automobile interior parts and floating components. Moreover, natural fibers can also be used as insulating materials in packaging and building panels. In this case some thermal properties are required. Therefore, the objective of this work was to evaluate the thermal behavior of the banana fiber by means of TGA, DTG and DSC analysis. The TGA curves revealed weight loss related to release of humidity and molecular structure decomposition. Peaks in the DTG curves indicated two intervals in temperature associated with different decomposition processes. The only endothermic DSC peak found was attributed to the lignocellulosic water of hydration being lost around 121°C.IntroductionIn recent times, environmental aspects related not only to pollution caused by non-degradable synthetic leftovers, specially polymeric wastes, but also to climate changes as a consequence of industrial activities, are motivating the use of natural materials. A particular case is fibrous composites, like the fiber grass composites. These synthetic materials, made from non-renewable polymers, are practically non-degradable and contribute to global warming by the CO2 emission associated with the energy required for the fabrication process. In spite of these environmental shortcomings, fiber materials are essential for the production of many items such as insulating chests, automobile cushion, construction panels, etc. An environmentally correct alternative to replace synthetic fibers composites is the naturally existing ones extracted from plants such as ramie and sisal. These have some environmental advantages of being renewable and degradable, these banana plant provide a negative contribution to C02 emission by absorbing greenhouse gas during the plant life cycle. Banana fibers have been used since long time in simple items such as ropes and rugs. Today they are used in engineering applications related insulation in building panels [2] and finish parts in automobile interior components [3]."

Jan 1, 2012

By Gaifeng Xue, Jingxuan Zhou, Shangchao Liu

"Both COD and TOC can characterize organic pollution of coking wastewater. In theory, there is a linear correlation between these two indicators. After continuous monitoring TOC and COD of coking waste water, linear regression relationship between of these to indicators was studied with the use of mathematical statistics. And conversion equation between these two indicators was established, and using t-test method for significance testing. The results showed that the linear relationship of COD and TOC was significant. Also interval estimation of equation slope and intercept were given in the condition of 95% confidence level. A linear regression equation established can be used to indirectly convert TOC to COD with high precision and accuracy.IntroductionBoth chemical oxygen demand (COD) and total organic carbon (TOC) are measure of the degree of characterization for organic pollution of water bodies. The current COD standard analytical methods is Potassium dichromate titration method [1] . there are some disadvantages in this method, such as only part of organic matter in the water bodies being oxidated, the refluxed steps, a long time needed for each measurement, high cost. It is the most important that sulfuric acid silver and mercury sulfate reagents used in the measurement may easily lead to secondary pollution. In contrast, the measurement of TOC is by the method of combustion or Photocatalytic Oxidation. The result could be easily got from the instrument. There are some advantages in this way, such as easy operation, short time and little expenses for each measurement and no secondary pollution 121• In addition, the measurement of TOC has higher degree of precision and accuracy than the measurement of COD both in the determination of calibration standards and actual samples. The meaning and contrast of TOC and COD are listed in the table 1."

Jan 1, 2013

By K. Hussin

Perlis is one of the major producers of ?Batu Reput? in Malaysia and majority of the deposits contain of high-purity calcium and magnesium carbonate. The composition of Batu Reput is similar with the ordinary dolomite. Currently, the ?Batu Reput? is used as filler in the road construction, however with this new invention, it can be value added and maximized its application in the daily life, for example as construction materials, decorative products, souvenir and etc. This paper presents the fabrication of Artificial Marble from ?Batu Reput? and in this case, it was used as filler in the matrix of epoxy which is acted as a binder.

Jan 1, 2006

By I. A. Ibrahim

Ilmenite, in its natural form, is an inactive mineral from which the selective removal of iron is rather difficult. The reactivity of ilmenite. so that it can be leached with dilute hydrochloric acid, can be enhanced by chemical reduction in solution using a suitable metal as a reducing agent. The present paper aims at the evaluation of an Egyptian ilmenite ore for the production of synthetic rutile by direct leaching with hydrochloric acid in presence of iron powder. In this process, the titanium and iron contents are dissolved; meanwhile, the dissolved titanium is hydrolyzed and re-precipitated leaving mainly iron in solution. Leaching conditions were optimized to obtain less iron in the final solid product. Addition of sufficient amount of iron powder during leaching reduces the dissolved Fe3+ to Fe2+ and reduces the dissolved Ti4+ to Ti3+. The creation of Ti3+ in solution is assumed to have a role in dissolving the ferric iron and hence increasing the reactivity of the ilmenite ore. Synthetic rutile of about 90% TiO2 and 0.77% Fe2O3 was obtained from ore with a grain size 100% passing 200 mesh and a 5-hour leach time with 20% HCl at boiling temperature (110°C) and 0.11 g iron powder / g ore.

Jan 1, 2003

By J. Ipinza

The slime formation with several metallic impurities from acidic electrolytes of copper has been studied. On fresh Pb-Ca-Sn anode surface firstly the formation of PbSO4 takes place, then, it is transformed in the conducting PbO2, which covers the anode surface. It has been experimentally established the formation of a manganese dioxide double layer at the anode; this double layer was always composed of a thick external layer of non-adhering and easily removable scales, and of a thin internal layer, which adheres relatively well to the surface of the electrode. It was found that manganese dioxides present in the slime were of different nature: a non-adhering layer produced by electrolysis (-MnO2) on the PbO2 surface and a pure chemical precipitation in the solution (-MnO2). When iron is present in the electrolyte on this last layer of manganese, lead sulfate was found. In the case of arsenic and antimony in the electrolyte the slime generated was found to be lead sulfate and amorphous compounds of those ions. The lower slime generation in Chilean EW plants could be due to the lower contents of iron and manganese in the electrolytes. It was found that this slime formation rate not only is due to the electrolyte composition but also to the poor control of operational parameters at EW plants.

Jan 1, 2003

By Yotamu Stephen Rainford Hara

"The study focuses on the reduction mechanisms of copper, cobalt and iron during carbothermic reduction of copper-cobalt mineral sulphide concentrates in the presence of lime, in the temperature range of 1073K and 1273K. We have used three types of mineral concentrates which were derived from froth flotation from the Copperbelt region in Zambia. The reduction mechanisms were studied using thermogravimetric analysis in which selected reactions were stopped at different times for characterising the reaction mechanism using optical microscopy, XRD and SEM-EDX analyses. Using SEM-EDX analysis, we have analysed in details the stages of metallic phase formation during reduction process. Metallic cobalt and iron were embedded into copper, thereby permitting magnetic separation of the reduced metals even though copper is diamagnetic. Methods of preferential reduction of metal values were investigated by analysing the metallic phase formation.IntroductionIn conventional smelting or converting of copper sulphide minerals, metallic copper forms by giving off S02 gas on. Although in terms of overall energy balance the selective oxidation for metal production has major advantages, the process suffers from drawbacks in smelting complex concentrates containing copper, cobalt and iron sulphides minerals and these are: (i) cobalt and iron are oxidised, and consequently cobalt is lost into the slag phase. (ii) The volume of S02 gas produced is in low concentrations, which is insufficient for extracting sulphur or manufacturing sulphuric acid. The release of dilute S02 causes serious environmental pollution. The major cause for the loss of cobalt and iron into the slag, is due to that fact that the oxides of these metals are more stable than their sulphides. Since cobalt and copper are more valuable than iron, reducing conditions are required in a separate slag treatment reactor using electric arc melting for recovering the lost metal oxides from slag. This energy-intensive step makes metal making expensive.During chemical beneficiation of mineral sulphides (Cu2S, CoS, FeS) in the presence oflime (CaO), two types of equilibrium conditions may be set up either by forming CaS under reducing conditions, or by stabilizing CaS04 under oxidising conditions [l]. By comparison in the presence of carbon, CaS and metallic phases form, enabling the recovery of metals from sulphide minerals, which have been investigated by a number of authors [2-9]. During reduction of metal sulphide in the presence of lime and with carbon, it has been proven that the overall reaction le proceeds via two main steps: [5, 8, 9] (i) the anion exchange reaction between metal sulphides (MS) and CaO as shown in equation la, followed by (ii) the reduction of metal oxide (MO) via reaction lb."

Jan 1, 2013

By W. H. Jay

Sulphide-containing minerals, particularly iron, lead to acid formation. In turn, the acid generates effluents such as copper acid drainage (AMD). The Berkeley Pit in Butte, Montana, USA and Mt Lyell in Tasmania, Australia, represent just two of many sites throughout the world for which acceptable treatment methods are required. In the gold cyanidation process, the presence of copper creates both a significant cost impediment and a potential environmental hazard. The tailings dam failure at Baia Mare in Romania which led to the release of copper and zinc cyanides created a major environmental disaster. The application of non-toxic water soluble polymers and ion exchange resins to selectively recover copper from AMD solutions, and the in-plant treatment of copper cyanide solutions and slurries to recover copper and recycle cyanide to prevent cyanide entering the tailings impoundment will be discussed. The economics of the various processes will be highlighted.

Jan 1, 2003

By Corby G. Anderson

Over the past 15 years, numerous pressure oxidation plants for pretreatment of gold ores and concentrates have been installed throughout the world. While this technology is now established, it suffers in terms of the complex engineering and operational characteristics inherent in utilization of high temperatures (i.e. up to 225oC) and high pressures (i.e. > 3000 kPag). This paper outlines the application of an industrially proven pressure leaching methodology utilizing nitrogen species catalyzed pressure leaching and alkaline sulfide gold leaching. As such, it stands as an economic and engineering advancement in pressure leaching and non-cyanide treatment of gold ores and concentrates. In particular, the technology offers significant technical and economic advantages over traditional pressure oxidation and cyanide gold recovery in the treatment of gold bearing chalcopyrite ores and concentrates. An example of this will application will be delineated in this paper.

Jan 1, 2003