Search Documents

By J. A. Brierley

A biooxidation-heap pretreatment process was field tested to evaluate enhancing gold recovery from a preg-robbing sulfidic carbonaceous ore. Newmont Gold Company&apos;s Gold Quarry sulfidic carbonaceous ore was inoculated with an iron-grown culture of Thiobacillus ferrooxidans to form a 495 ton test heap. Biooxidation was conducted for a period of 100 days. The most active period of biooxidation occurred during the first 40 days of pretreatment? About 35 to 40% of the sulfide was oxidized. The extent of biooxidation was considered good as the ore particle size was relatively large 58% >1?9 cm (&apos;/< inch). The larger particle size ore limited the extent of bacterial activity. The field test demonstrated the ability to conduct biooxidation in a small pilot test heap. Thiourea was evaluated for extraction of gold from the biooxidized preg-robbing ore.

Jan 1, 1995

By Hongbo Yang, Tongbo Zhang, Ting Huang, Jingshe Li, Fangfang Song

"Liquid core length is a very important parameter of the process of continuous casting, which directly reflects the cooling status in secondary cooling zone and solidification rate of the slab. In this paper, the billet caster in some steel plant in China was chosen as the prototype of simulating. A numerical simulating model for calculating the liquid core length of continuous casting billet was built by ProCAST software, which was verified reasonable and accurate by pin-shooting technique. Based on the model, the relationships between casting speed, casting temperature and liquid core length of casting billet were found, which was very practically useful for the workers on sit to improve casting billet quality. IntroductionContinuous casting process developed very rapidly because of the high metal yield, energy saving, and low-cost 111• And the quality requirements of continuous casting billet for customers became higher and higher with the fast development of economic121• Internal defect usually is the major quality problem for continuous casting billet[3•61 , which is influenced by the solidification process of casting billet, especially the solidification process of liquid core17•81 • So it is very important to study on the relationship between casting parameters and the liquid core length which means the distance between the crystallizer meniscus and the casting billet solidification end-point. In practical production process, the workers usually control the quality of casting billet according to the liquid core length."

Jan 1, 2013

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite (CuzS) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical eqUilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By Joseph Sofra

It has become increasingly evident that sustainable metals production in the 21" century requires producers to balance the needs of cost effective, high value production with that of responsible plant operation. This is becoming more difficult as lower grade and more complex feed materials, including recycled scrap and residues, arc being processed to reduce production costs and decrease exposure to primary metal market fluctuations. One particular facet of the metals industry facing these challenges in the 21 st century arc copper producers. The recent steady decline in the copper price has seen the industry cut expenditure, tighten control on income streams and focus on high returns on capital investment. For these reasons copper producers arc looking towards flexible technologies that can deliver high value products, with minimal environmental impact at low capital and low sustainable operating costs. Ausmelt&apos;s Top Submerged Lancing (TSL) technology for copper production is a low cost, proven technology for the processing of both primary and secondary copper materials. Both the smelting and converting operations introduce significant advantages in environmental performance, improved process efficiencies and high rates of metal recovery. Ausmelt has made significant gains in the past 4 years in establishing a strong market position for its copper technology. New installations in China, South Africa and India as well as existing operations in Zimbabwe and China have demonstrated its effectiveness. This paper reviews the application of Ausmelt Technology for both smelting and converting of primary and secondary sources. It discusses Ausmelt&apos;s design and implementation philosophy, and how this philosophy meshes with the needs of the end user.

Jan 1, 2003

By Thomas R. Wildeman

Experimental methods for studying vapors over solid minerals are reviewed and an especially developed method using atomic absorption is described. The method is used to study vapor pressures over Te. Ag, Au, Ag2Te, and AuTe2 from 250°C through 10S0oe. Vapor pressures observed and, concurrently. sintering properties are significantly altered by the form of the solid. The vapor pressures of the tellurium compounds reveal complex processes occurring on the surfaces of the solids. The data given also point out a method of recovering precious metals from their telluride minerals w

Jan 1, 1987

By Kirsi M. Riihilahti

The oxidation characteristics of solid copper matte particles under simulated Kennecott-Outokumpu Flash Converting conditions are presented. This project is concerned with the determination of the effects of operating variables on the reaction of the particles. Experiments were carried out in a large laboratory-scale flash furnace with 72 wt-% Cu matte by varying initial particle size, temperature, oxygen partial pressure, oxygen-to-matte mass ratio and residence time. Chemical analysis was used to study the oxidation extent and copper volatilization. Particle fragmentation was examined. Fractional conversion and sulfur removal slightly decreased with initial particle size, while a higher oxygen-to-matte mass ratio mainly resulted in higher fractional conversion and more efficient sulfur removal. The fractional conversion values represented the overall extent of oxidation more closely than degree of sulfur removal.

Jan 1, 1997

By Stefan Mutz

In Germany the automobile recycling is regulated by law. Current legislation requires that by the year 2015, eighty five w.-t. % of the components from used cars ill be materially recycled. Whilst for 10 w.-t. % of the materials a thermal utilization is certified, there are still some concrete questions that remain unanswered regarding the usability of single fractions. The recent innovative approaches to the concepts of used cars dismantling do not alter the fact that the majority of the materials of used cars still have to pass over the shredder and the connected processing aggregates. The status of the so called SLF (Shredder light fraction) which is about 25 w.-t. % w.-t. in used cars, has not been satisfactorily clarified. Furthermore questions still remain regarding the separation of the NMSF (nonmagnetic metal shredder fraction) which has to be separated in the single metallic fractions like stainless tell, copper, brass, zinc, etc. Attempts of optimization can be found. This paper analyses some of the difficulties being encountered by the automobile recycling industry in Germany, before reviewing some of the innovative approaches that the industry has introduced. Finally the paper goes on to describe the potential of automatic picking. Examples of a series of tests, utilizing this technology, in which a variety of products from a range of shredders were isolated are described in detail. This new technology provides a range of applications to the automobile recycling industry.

Jan 1, 2002

By Christoph Beckermann, Kai Liu, Richard A. Hardin

"A two-dimensional heat transfer model for transient simulation and control of a continuous steel slab caster is described. Slab thermal and solidification conditions are computed by the model as a function of time-varying casting speed, secondary spray cooling water flow rates and temperature, slab thickness, steel chemistry, and pouring and ambient temperatures. A solidification model that includes the effects of steel chemistry, cooling rate and mierosegregation on the solidification path is incorporated directly into the caster model. Comparisons between measured and predicted liquidus and solidus temperatures are given for two low alloy steels, and show good agreement. Predicted and measured slab surface temperatures recorded on an operating caster are compared with this transient model and show that the model can predict the temperature response at the slab surface. Results of several simulations are given to demonstrate the effects of changing casting conditions on the slab thermal profile and the solidification end-point. A control methodology suitable for online control of a continuous casting machine is described, and its ability to control the surface temperature profile by dynamically adjusting secondary spray cooling flow rates is demonstrated using the simulator. IntroductionIn order to remain competitive in today's world-wide market for continuously cast steel products, steel producers are finding that it is ever more important to implement process control and to develop a more thorough technological understanding of their casting process. By integrating process control and monitoring into both production and quality control, producers are better able to meet customers' demands for steel of the required quality, quantity, size, grade, and properties at the lowest cost. Computer models used for real-time/on-line prediction and control of continuous steel casters are fundamental tools to accomplish this. Accurate on-line prediction and control of steel solidification and heat transfer allows for more flexibility in caster operation by giving operators the ability to change casting speeds while keeping critical process parameters within required ranges. Such control 'capability also results in more uniform quality throughout an entire casting sequence from startup to shutdown. Furthermore, due to the unreliability of temperature sensors, and the lack of good sensors for important process parameters such as solidification end-point and liquid pool depth, computer-based control models are often the only available option."

Jan 1, 2000

By G. Van Weert

The pellet reactor was developed approximately 20 years ago in the Netherlands for softening drinking water. Since then, some 35 plants have been built, ranging in capacity up to 8500 m3/h. Applications now also include removal of phosphates and fluorides and the production of metal carbonates and sulphides from waste streams. The pellet reactor consists of a fluidized bed, wherein the process solution is thoroughly mixed with the precipitation reagent at special inlet nozzles to give over-saturation of the compound to be precipitated. In water softening applications, the compound is CaCO,. In the case of nickel or other metal waste streams, Na2CO3 solution is added in sufficient amounts to precipitate metal (hydroxy) carbonate on the fluid bed particles. These grow typically to dense spheroids, which are removed when they reach 0.8 to 1.0 mm diameter. These spheroids are easily dewatered, free flowing and low dusting. The latter property is becoming an attractive advantage in connection with new plant hygiene regulations. The operation of a 60 cm diameter pellet reactor on nickel containing plating waste is described and the properties of the produced nickel carbonate spheroids are discussed.

Jan 1, 1993

By Chu Yong Cheng

Synergists can be used in solvent extraction to improve the selectivity of extractants for metals. Research work carried out by the SX group at the AJ Parker Cooperative Research Centre for Hydrometallurgy / CSIRO Minerals has shown that the pH isotherm of nickel with Versatic 10 was significantly lowered by the addition of the synergist Acorga CLX50. The paper discusses how this synergistic shift can be used to alleviate a gypsum formation problem at Bulong nickel laterite operation in Western Australia. Metal pH isotherms were obtained with Versatic 10 and synergist CLX50 using synthetic leach solutions. In terms of pH50, the extraction order of the metals with 0.5 M Versatic 10 alone was Cu > Zn > Ni > Co > Mn > Ca > Mg, whilst the extraction order with Versatic 10 and 20% by volume CLX50 was Cu > Ni Zn > Co > Mn > Ca > Mg with the pH50 (Mn-Co) significantlyincreased. This is significant because the isotherms of valuable metals Ni, Cu, Co and Zn shift more towards low pH than those of the waste metals Mn, Mg and Ca, resulting in a possible good separation of Ni, Cu, Co and Zn from Mn, Mg and Ca. The use of intermediate precipitation, solids/liquid separation and re-leach in the three Western Australian nickel plants make these processes complicated and costly in capital and operation. The research work carried by the SX groupat the AJ Parker Centre has led to the development of direct SX (DSX) processes to recover nickel and cobalt from leach solutions using synergistic organic systems. Semi-continuous tests with a BHP Billiton pilot plant leach solution showed that Ni and Co together with Zn and Cu were separated from the major impurities, Mn, Mg, Ca, and Cl, in the first SX circuit. The co-extracted impurities were easily scrubbed. After stripping, Ni and Co together with Zn and Cu were concentrated, resulting in a much smaller second SX circuit in the down stream processes.

Jan 1, 2003

By W. G. Davenport

This chapter demonstrates how our matrices can be used for controlling a flash furnace. Specifically, it shows how we can determine the adjustments in industrial oxygen, air, oil and flux input rates that will; (a) correctly alter product temperatures and compositions to newly targeted values (b), maintain set-point product temperatures and compositions with varying feed compositions and feed rates. It also discusses corrective actions that might be taken when furnace temperature and matte grade unexpectedly change.

Jan 1, 2001

By J. M. Shneerson

At Gipronickel Institute a technological flowsheet of pressure leaching of copper from rich copper concentrates (i.e. containing: Cu -59-75%; Ni -D.5-4.64%; Fe -D.2-J.3%; S -21.8-26.9%) was developed. As a result, the possibility of deep decomposition of copper-containing minerals with extraction of elemental sulphur (up to 90-95%) was established. The obtained sulphur concentrates contain 80-90% of elemental sulphur, which can be separated from sulphide residue through autoclave melting and settling. As a rule, sulphide concentrates remaining after extraction of sulphur contain up to 1-2% of noble metals. The sulphide concentrate can be purified to the level of rich concentrates or pure metals using the well-known methods as in the case of tankhouse slimes. The presented research specifies the parameters of main operations: pressure leaching and sulphur extraction. It was established that 98% of copper could be transferred into solution at temperatures of 108-1 10°C and oxygen partial pressure 0.4-0.6 MPa. Experiments were carried out in autoclaves of various volumes using the products of nickel matte processing.

Jan 1, 2003

By Jiang Fan, Liu Shi, Wang Haigang

Winter-time natural convection in gravel embankments has been suggested as a technique to provide passive cooling and thereby avoid thaw-settlement of roadways located in permafrost areas. Numerical simulation by finite volume method on the proposed model is perf9rmed using the software FLUENT. A gravels model, in which the embankment is composed of stones and air, has been adopted to investigate the temperature and velocity fields in embankment. Simulation results show that in summer, a weak clockwise circulation of the pore air extending throughout most of the embankment. The pore-air motion is very weak which results in relatively straight horizontal isotherm lines. And heat transfer is mainly maintained through conduction. But in winter, pore-air velocities are higher and multiple vortexes are formed in the embankment. Natural convection then becomes the dominant influence on the isotherm shapes within the embankment. As a result of low ambient temperatures exerted on the embankment surface during winter months, an unstable air density gradient develops within the embankment. This convection increases the heat flux out of the embankment. Therefore, the winter-time convection can further reduce the temperature of the foundation soil beneath the open-graded embankment. In addition, the effects of the size of the stones within the embankment have been analyzed and compared in the gravel model. It shows that in winter, 200mm stones lead to stronger vortexes in the embankment compared with those of 60mm stones. Consequently, the zone oflow-temperature beneath the embankment is extended.

Jan 1, 2004

By M. K. Mohan

During the processing of metals like Cu, Ni, Co, large quantities of solutions, which contain co- products such as Sb, Cd, Pb etc. are generated. These solutions if processed to recover the metals help in conservation of metals as well as environment preservation. The present study was taken up to recover antimony from process solutions using zeolites. The effect of pH of the solution, time and type of zeolite viz., chabazite, mordenite, erionite and clinoptilolite on the sorption of antimony was investigated. Rate of sorption increases with pH and about 77-pct. antimony sorption was observed with chabazite at a pH of 6. Optimal conditions were established for the maximum recovery of antimony fiom process solutions. The mechanism of sorption for Sb was proposed in terms of adsorption and intraparticle diffusion. The calculated adsorption constants from Langmuir and Freundlich equations indicated that the adsorption of antimony on chabazite was strong.

Jan 1, 1999

By Hu Meilong, Liu Lu, Bai Chenguang

Extracting perovskite from high titanium-bearing blast furnace (BF) slag is a green and potential method to recover the second titanium resource. The non-isothermal crystallization process of perovskite in synthesized high titanium-bearing slag was studied in situ by confocal scanning laser microscope (CSLM) with cooling rate of 20 K/min. The results showed that perovskite was the primary phase formed during cooling process in the titanium-bearing synthesized slag (TiO2=23%). Perovskite started to precipitate at 1719 K and finally presented an orthogonal straight lines morphology.

Jan 1, 2014

By Guangshi Li, Xionggang Lu, Xueliang Xie, Xingli Zou, Yuyang Bian, Hongwei Cheng, Kai Zheng, Changyuan Lu

The corrosion resistance and corroded microstructure of MgO-C refractory in molten slag are investigated by immersion test in muffle furnace at 1600 °C . The microstructure and chemical compositions of the specimens after erosion experiment are characterized by scanning electron microscope (SEM) and energy dispersive X-ray (EDX). The results confirm that the oxidation of graphite is the most important degradation mode of MgO-C refractory. The structure of the refractory material is damaged due to the decrease of graphite, as a result, the periclase substrate reacts with the molten slag directly. The corrosion process is controlled by the dissolution of the refractory materials into slag, low melting point oxides are therefore generated which lead to the damage of MgO-C refractory finally.

Jan 1, 2015

By K. Mansfield

Spent Pot Lining (SPL) is an unavoidable waste product of the electrolytic process in the smelting of aluminium. SPL is considered to be a hazardous waste in various countries because it contains significant quantities of absorbed fluorides along with traces of cyanide. In 1995, Portland Aluminium undertook the investment of AUD$26,400,000 to construct a Research and Development processing facility at Portland, Victoria, Australia, to treat SPL. Extensive research, development and design were carried out over 5 years prior to the investment decision. This study led Portland Aluminium to install an Ausmelt pyrometallurgical furnace to combust and melt the SPL producing a hydrogen fluoride (HF) laden gas, which was cooled and then converted to aluminium fluoride (AlF3). Both the cooling and AIF3 manufacture were processes developed by Portland Aluminium. Many commissioning, equipment reliability and process problems have been encountered that had not been experienced in the trials at Ausmelt or in the developmental process for the treatment of the furnace offgases to form AlF3. Designs based on anticipated process expectations have had to be re-engineered by the SPL team to ensure plant and operational success. In June 2001, the installation of the final major component - a slag granulation process - was completed. This has produced a vitrified (glassy) slag that is expected to have leachability qualities acceptable to the Victorian Environment Protection Authority (EPA) to allow commercial end uses of the slag material to be developed. Today (September 2001), the smelter has successfully used the fluoride product, namely 65- 70% AIF3, in aluminium production and the SPL plant has significantly increased throughput with expectations to be at annual design rates of 12,000 tonne of SPL in early 2002. "The Alcoa Portland SPL Process" has been technically developed and is a proven process for the treatment and recovery of valuable components from SPL materials.

Jan 1, 2002

By C. A. Nogueira, F. Margarido

"A research work has being carried out annmg at evaluating the possibility of treating simultaneously several electrochemical systems of spent batteries using the same process, in order to overcome the high costs and difficulties of selective collection and sorting. Zn-Mn02 systems, representing more than 75% of portable battery market, shall be treated in dedicated processes. The treatment assessment using a single hydrometallurgical process of the other major systems (NiCd, NiMH and Li-ion), having Ni and Co as main metals, was the aim of the research work here reported. Sulfuric acid leaching was demonstrated to be adequate for dissolving more than 90% of the metals of interest contained in batteries. The subsequent separation of metals by solvent extraction, using organophosphorous extractants like DEHPA and Cyanex 272, allowed the production of pure solutions of rare earths, cadmium/manganese, cobalt, nickel and lithium, enabling their further recovering.IntroductionRecycling is the best approach for end-of-life management of spent batteries mainly by environmental reasons but also motivated by resources conservation and, in some cases, by economic profits. Most relevant electrochemical systems of portable cells are Zn-Mn02 (ZMB, alkaline and saline), nickel-cadmium (NiCd), nickel-metal hydride (NiMH) and lithium-ion (LIB). These batteries are collected, sorted and usually treated separately, applying for pyrometallurgical or hydrometallurgical technologies, the former being the most common.Several processes have been developed and some of them industrially applied, as described in some available review papers [l, 2]. In Europe for ZMB systems the oldest processes are Batrec [3] and Citron [4]. Although having differences in details, both are based on pyrometallurgical recovery of zinc by distillation, in metallic or oxide forms, being manganese retained in the slag together with iron. Hydrometallurgical alternatives are also available, like Zincex [5] and Recupyl [ 6] processes, both using sulfuric acid solutions as leachant. The application of the existing technologies to battery recycling, instead of using dedicated processes, is other alternative already tested, being the Waeltz furnace or the Imperial Smelting some examples."

Jan 1, 2012

By R. Nilsson

In the present work, an assessment of the sulphide capacities of a number of binary and ternary slag systems have been carried out in the light of a sulphide capacity model. The model is based on the expression: {CS- exp (-A G °/R T) ? ao2 / fs2-} where AGO is the standard Gibbs energy change for the above reaction, ao2 is the activity of oxygen ions and f, is the activity coefficient of the sulphide ion in the slag. In the present model, the ratio (ao2/fs2) is optimized for the experimental data available in literature. The systems assessed are the binaries MnO-SiO2, CaO-SiO2, Al2O3-CaO, as well as the ternaries CaO-Al2O3-SiO2 and CaO-MnO-SiO2. In the case of all these systems, the experimental data available in literature were complemented by measurements carried out at the Division of Theoretical Metallurgy. The sulphide capacities of some FeO- containing binary, ternary and quaternary slags are also examined. The potentiality of the model to estimate the sulphide capacities of complex slag systems from binary and ternary data is demonstrated.

Jan 1, 1996