Search Documents

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (K. McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project will be completed in early 1998.

Jan 1, 1998

By K. H. McDaniel

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modi tying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identity and quantity operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By K. H. McDaniel, L. Griswold

The Waste Isolation Pilot Plant (WIPP) is adding a third fan to operate in parallel with, and supplement, its two existing main fans. An engineering analysis conducted in 1995 identified the need for improved system availability and efficiency. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) Carlsbad Area Office facility designed to permanently dispose of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Engineers at the WIPP performed a feasibility analysis for either modifying, supplementing, or replacing its two main mine fans. Since the centrifugal fans were installed in 1988, multiple operational and performance concerns have been identified. A comprehensive engineering study was conducted (McDaniel, et al., 1997) to: identify and quantify operational concerns, evaluate possible alternatives, and recommend an optimum solution. The study indicated that adding a third single-duty centrifugal fan similar to the two existing fans, and equipping that fan with Inlet Van Controls (IVCs) was the best choice. This alternative provided the most desirable combination of operational readiness, and improving system performance. The fan installation project accommodates several operational and scheduling constraints. WIPP is scheduled to receive waste in May 1998. This milestone is proceeded by an operational readiness review. Fan installation could not be allowed to compromise the WIPP's ability to declare facility readiness and had to minimize operational disruptions during the system tie-in. All engineering for the project is completed and physical modifications started in July 1997. The project was completed in 1998.

Jan 1, 1999

By R Schiller, E Chait

"Quebrada Blanca is a porphyry copper deposit located in the Eocene-Oligocene belt of Chilean Andes. Operation started in 1994 and original reserves for supergene mineralisation gave a life-of-mine (LOM) of 20 years; however, further exploration extended the LOM until 2020.In order to optimise the remaining five years of supergene resource, geometallurgical variables were added to the geological model including copper recovery and acid consumption. LOM plan encompasses finishing the phase number eight and the future development of phases 11 and 13.LOM lithologies include diorites, quartz monzonites, porphyries, igneous and tourmaline breccias. Main alterations are: potassic, phyllic and argillic. Litho-alterations or geometallurgical units were formed by combining five types of rocks with three types of alteration. According to statistical information, the deposit can be represented with 12 litho-alteration units, which cover 98 per cent of the LOM volume.For copper recovery information, there were 40 mini-columns tests made in order to obtain kinetics curves and copper recovery values after comparing the difference between head and tails grades. Acid consumption was obtained using an automatic neutraliser device-based test.Historical data said that copper recovery in pads after 450 days of irrigation is around 75 per cent of recoverable copper while acid consumption is around 5.5 kg/t.According to this study, lower recoveries are related with potassic-altered diorites and argillic-altered quartz monzonites with values around 60 per cent. On the other hand, best recoveries could be found in potassic-altered quartz monzonites and argillic-altered diorites with values closer to 80 per cent.It was also revealed that the most reactive rock is the potassic-altered diorite with 12 kg/t of acid consumption. This rock covers approximately 40 per cent from phases 11 and 13.The final geomet model was calculated using a program that relates each geometallurgical unit with a specific copper recovery and acid consumption value. Results found after comparing model-obtained information with historical leached pads data were used to validate the model.CITATION:Chait, E and Schiller, R, 2016. Adding Copper Recovery and Acid Consumption Variables to the Geological Model of Quebrada Blanca, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 257–266 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By F Solomon

This paper explores the recent escalation in public opinion for business to demonstrate the social value it generates through its activities. The concept of social capital is analysed, including the linkages between social and environmental values. Also discussed are the challenges inherent in devising a method for evaluating social value, determining appropriate performance indicators and then evaluating acceptability of outcomes. The linkage between accountability and added social value in the minerals industry is analysed. This includes an illustration of the models of accountability that are now emerging and the adding of social value.

Jan 1, 2000

In this paper, three types of value-adding in the minerals industry are discussed: downstream processing, improving the efficiency of existing processing and increasing the knowledge base and expertise of the staff. It is shown that, while downstream processing seems to offer a good way of improving Australia's trade position, there are a number of impediments to such development, notably, limited access to the appropriate technology and overseas markets. Transport costs can also be a problem. To reverse the situation will require more positive policies by government. In the meantime, something can be done towards adding value by increasing the efficiency of existing processes. Examples are given, showing how it might be possible to make economies in reagent costs in the gold industry, how innovative technology has led to more complete processing of a tailings dump, how research might lead to an increase in the throughput in the production of synthetic rutile and how it is possible to leach selectively from gold/copper ores.

Jan 1, 1995

Solid Energy New Zealand Limited has grown significantly since becoming a State Owned Enterprise in 1987. Exports, profit, turnover, output per employee are all trending upwards. The company has identified the management of Health and Safety as a key capability to sustain future growth, and to add value to the business. It has set a target of being the best practice in managing Health and Safety.   This paper examines the company's activities in the Health and Safety area, and how it sees that value can be added by preventing and containing losses through accidents involving people, property, process and the environment. Solid Energy is confident that a Planned approach to managing Health and Safety can achieve this. It will explore historical events, strategic changes, Health and Safety systems, Benchmarking, Performance Measures, initiatives, progress to date and challenges for the future.

Jan 1, 1997

By Martin Irving

Adding Value to Canadian Diamonds - A Changing Diamond Industry - Diamond Mining - Diamond Manufacturing - Diamond Jewellery Markets - NWT Diamonds Changing Diamond Industry - De Beers ? privatization - Oppenheimers (45%), Anglo-American (45%), Botswana (10%) ? going retail - LVMH joint venture - New Players ? jurisdictions - Canada ? companies - BHP-Billiton - Aber Diamonds

May 1, 2002

By Andrea B. Baldwin

Solvay Minerals, Inc. (formerly Tenneco Minerals Company) is one of five producers who use trona to produce soda ash at Green River, Wyoming. Over the years, many producers, including Solvay Minerals, extended their product lines by manufacturing other sodium products based on trona. This paper focuses on the criteria used by Solvay Minerals in the selection of new products added at its Green River, WY operations. An example is given in the selection of caustic soda production.

Jan 1, 1993

By E. R. Dixon

Copper SX/EW plants often bleed part of their electrowinning electrolyte to control impurities and maintain consistent cathode quality. Depending on the specific situation at each site, the bleed is either returned to raffinate, to an SX extraction stage, to an SX wash stage, or to the PLS pond, to avoid losing the copper in the bleed. This practice can have undesirable effects on the overall process. An alternative is to electrowin all or most of the copper in the bleed, thus avoiding the recirculation of the copper in the bleed. In this manner, the bleed is converted to metallic copper without interfering with the SX circuit. This in turn reduces the copper concentration in the raffinate, improving global copper recovery because of improved leaching conditions.

Jan 1, 2007

By T E. Norgate

Salinity in Australia is caused by over irrigation and land clearing for agricultural use over the last 100 years. It is now the biggest threat to the quality of land and water in the Murray Darling Basin and Western Australia. Pumping the saline waters straight into the ocean or transporting the solid residue (mainly sodium chloride) to the ocean after evaporation of the water is expected to cost the taxpayer millions of dollars every year. This paper proposes that the salinity problem of Australia, at least in part, can be converted to an asset rather than a liability if it is exploited and used to make value-added products. The more value made out of saline waters, the more saline water is processed and therefore the more salt is extracted from the land. The value-added products that can be made out of saline waters are numerous and diverse. Rough calculations show that value addition to the saline waters could potentially generate up to $A 200 million per annum business in the Murray-Darling Basin. Although it is a challenge to make cost competitive products and find markets for these products it is possible that up to $A 100 million per year may be gained from import substitution. Value addition to salinity would also reduce the threat on the environment and existing agricultural industry. Investment to add value to salinity will create business in the region, nurture the local small population communities, and increase services and long-term employment.

Jan 1, 2002

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By L Ventura, M Almond

The Pueblo Viejo project in the Dominican Republic installed an innovative sample system on its reverse circulation (RC) drilling rig during commissioning and subsequent commencement of operations. As knowledge of the orebody increased with mining and plant production, cost pressures became apparent that raised questions concerning the continued use of RC drilling versus blasthole sampling for ore control.To justify the continued use of RC drilling for grade control, an in-depth study was undertaken to determine the quality of the sample and prove its value-add to the operation.To investigate the differences in sample quality, a complete bench trial was initiated across both ore pits to compare RC drill results with blasthole assays on a side-by-side basis. The results indicated that based on ore block comparison between RC and blasthole sampling, RC identified an additional 20 per cent of high-grade (+ 4.5 g/t Au) ounces.Previous work indicated that Au, Ag and Cu were all elevated in the drill fines at Pueblo Viejo (Goers and Almond, 2012). This previous test work did not consider the quantity of fines in an RC sample therefore new test work was undertaken to include particle size distribution analyses. This study would determine if the inclusion of fines in the sample was occurring and compare the quantity of fines in the sample against other sample systems and blasthole samples.Comparisons between RC samples and blasthole samples indicate that for the RC samples a range of 30–35 per cent of the sample passed 300 mesh as compared to blastholes where the range of the sample passing 300 mesh was 15–30 per cent.This paper includes a case study on the importance of accurate samples and how they have impacted throughput through the pressure oxidation process plant at Pueblo Viejo. The accurate samples provided by RC allow for improved stockpile and blending strategies, showing the importance of accurate samples to manage risk and create value, against the perception that savings can be made at the risk of poor sampling performance.CITATION:Almond, M and Ventura, L, 2017. Adding value with reverse circulation drilling at Pueblo Viejo, in Proceedings Tenth International Mining Geology Conference 2017, pp 277–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By Luciana Lezira Pereira de Almeida

With the increasing use of ornamental rocks, mainly in civil construction, sundry problems were identified in relation to rocks cutting, such as efficiency in the cutting process and rock quality lumber. In recent years several composites have been developed to solve these problems. In this context, the study of the binomial matrix metal-diamond interaction is of paramount importance for the development of new composite materials to improve the efficiency of the cutting tool. The diamond impregnated matrix metal often reveals a reaction between the diamond surface and the matrix. Besides the mechanical connection, chemical reactions can sometimes occur. Therefore, this study aims to assess the achievement of diamond composites in the system Fe / Cu / Ni / Sn via powder metallurgy, with added CRB2. Analyzes have been performed to characterize chemical / physical and mechanical. The results have showed that addition of CRB2 promote significant changes in the properties of composites, especially in wear resistance and fracture toughness. Furthermore, the presence of the composite CRB2 causes a significant improvement in thermal stability.

Aug 16, 2017

By John L. Lamont, Walter Crafts

ADEQUATE hardenability has long been recognized as one of the first requirements for producing desired mechanical properties in a heat-treated steel. Since the introduction of the Jominy end-quench test1 and the development of correlative information to expand its use, industry has had an effective measure of hardenability. Prediction and control of the hardenability have been made possible by Grossmann's principle2 for calculating hardenability from chemical composition; and Field's conversion3 from depth of half-martensite hardening to Rockwell C hardness has made the relation more quantitative. These developments have facilitated the design of new steels and the control of standard grades to the extent that it has been possible to establish tentative hardenability bands for some of the more commonly used alloy steels.4 As the depth of hardening of the Jominy test specimen is usually measured by Rockwell C hardness, it was considered that it should be possible to predict the hardness by a more direct calculation. It has been found that this can be accomplished by the addition of Rockwell C units proportional to the carbon and alloy content, grain size, and position in the Jominy test specimen. The calculation has been found to be fairly accurate, and because of its additive character is relatively simple to use. In principle the method of calculation is somewhat similar to the expressions developed by Herty, McBride, and Hollenback,5 Burns, Moore, and Archer,6 and Burns and Riegel.7 The calculation is started from a base that includes the effects of carbon content and position in the Jominy test speimen. Rockwell C units are added to the base in proportion to the alloy content and grain size. This sum represents the Rockwell C hardness up to the level at which a disproportionate increase of hardness is caused by the formation of martensite, and above this level an increment for martensite hardening is added. The effects of alloys are directly proportional to the amounts present and are independent of each other, the carbon content, and the position in the specimen. Furthermore, the factors for determining the martensite increment are dependent only on carbon content and are independent of cooling rate and alloy content. It is this absence of interrelation between the different factors that makes it possible to calculate the hardness and makes the method of calculation consistent with the principle that the character of the hardening reaction is governed primarily by carbon and that alloys exert their effect chiefly through control of the critical cooling rate. The principle of the calculation, and the effects of alloys on the critical cooling rate,

Jan 1, 1945

By Jorge Alberto Soares Tenório, Romano Espinosa, Felipe Fardin Grillo, José Roberto de Oliveira, Denise Crocce

"The aim of this work was evaluation of the recovery of Zn and Fe of the EAFD added to the hot metal in the form of briquette at temperature of 1500°C. The EAFD was agglomerated by cold briquetting and introduced in the hot metal. This study utilized a bench-scale equipment to melt, during this process to kept a flow rate of inert gas above the bath. Were collected periodically metal samples and the samples were analyzed for determination of the content of total silicon and carbon by chemical analysis. Zinc oxide, zinc ferrite and other oxides were reduced and were volatized and collected by a cleaning system of dust (baghouse) located on top of the oven. More than 98% of iron were recovered from EAFD during the test. It was possible to produce a dust containing about 68% zinc by means of adding of EAFD.IntroductionIn the first semester of 2010, steel production was about 706 million tons, 27.9 % more than in the first half of 2009. Not a significantly increase if 2010 data is compared with the first semester of 2007 (only 7.2 % higher), before the world’s economic crises. Steel production is divided into two main routes. The first one, and most used, is the Basic Oxygen Furnace Process (BOF process), which in 2008 accounted for approximately 67.1 % of steel production. The second route is carried out in the Electric Arc Furnace (EAF) that in 2008 represented 30.6 % [1 ].Electric arc furnace dust (EAFD) is a solid waste generated during the steel making process. It is classi?ed according to NBR 10004 as dangerous solid waste-class I, because the elements Pb e Cd leach in water exceeding the maximum limits permitted by the NBR 10004 [2 ]."

Jan 1, 2012

Additional Attractive Force Between Alumina Particles Due to Low Solubility of Dicarboxylic Acids

Sep 13, 2010

By André Vervoort

After the systematic closure of Europe’s coalfields in the late twentieth century, the emphasis is now clearly on industry’s environmental legacy. One aspect of the latter is the longterm surface movement above abandoned coal mines. The analysis of satellite data shows that the subsidence lasts longer than generally assumed. However, a few years after the flooding of the abandoned underground coal mines, a new phenomenon was observed, i.e., the direction of the surface movement was reversed. The phase of upsidence has already lasted for several decades, and only future measurements will tell how long it continues. A key conclusion is that the regions with maximum subsidence do not necessarily correspond to the greatest upsidence. In other words, buildings and infrastructure are subjected to a different loading from this upsidence than during the subsidence phase. The longterm surface movements have an impact on vulnerable structures in the densely populated regions of the former deep coal mining areas in Europe. These movements create additional damage. This new knowledge is also relevant for mines that are still in operation or future mines that are planned.

Feb 1, 2024

By C. K. Leith

(San Francisco Meeting, September, 1915) IN 1911, we published in the Transactions a brief account of the lateritic alterations of serpentine in eastern Cuba, producing the important iron-ore deposits of the Mayari and Moa districts.1 The special feature of that article was a quantitative treatment of the alterations, based on analyses, to show just what had happened in terms of chemical, mineralogical, and physical changes. Professor Kemp has published an interesting account of these ores, containing additional quantitative observations of his own, tending essentially to confirm the nature of the changes that bad been worked out.2 His discussion suggests to us the desirability of publishing certain additional quantitative data which were not included in our previous article. This seems especially desirable because quantitative measurements of lateritic alterations are rare, and this particular case may be regarded as typical of a fairly wide range of alterations of this kind. At the time of our examination of Mayari and Moa, deposits 29 complete analyses were supplied us by the chemists of the Spanish-American Iron Co., representing a graded series from the unaltered serpentine rock below to the ore at the surface. These analyses are given in the accompanying table. The mineralogical composition of the ores and rocks is comparatively simple and can be easily calculated from the analyses. In Fig. 1 the mineralogical changes from the serpentine rock below to the lateritic iron ore above, based on the analyses, are expressed in terms of weight, assuming alumina to have remained constant during the alteration. It is not easy by mere inspection of this table of analyses to determine what the progressive chemical changes have been in development of the ore. In order to bring this out clearly, the analyses have been graphically represented in Fig. 2 in such a fashion as to show the progressive additions and losses of substances during alteration.

Jan 7, 1915

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1915.) ADAMS, ARTHUR K., Lieut., Co. 2, E. 0. T. S., Camp Humphreys, Va. AMIDON, CLAUDE E., 11th Training Co., Casual Camp, Camp Cody, N. M *BARBOUR, P. E., Capt., Engineer Corps, U. S. A. *BENHAM, W. M., Master Engr., Headquarters Dept., 115th Engrs. A. E. F., Care Postmaster, N. Y. BICKNELL, H. L., Pvt., Co. D, 27th Engrs., Camp Leach, D. C. *BLANDY, S. H. B., Lieut., Royal Horse Artillery, B. E. F.

Jan 10, 1918