Search Documents

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By G Kuntz, V Wall, B New

The prime aim of the Campbell Mine project was to develop a 3D geological model for the Campbell-Red Lake system to contribute to an exploration model for the region. The base data is composed of over 60 years of geological data covering an area of 16 by 8 km, and from surface down to 1830 m depth. This paper concentrates on the methods used in the GeoSpace system for the processing, integration, display and interpretation of such a large and diverse data set. A block model was developed that recorded the relative frequency of each geological feature within each block. The data input for the block models were based on recoding of the Campbell Mine drilling and channel sample databases into lithological, alteration and structural subsets. The value for each geological characteristic inserted into each block is calculated from all available data that falls within the block. Relative and absolute comparisons of the individual variables provide a targeted outcome from which the blocks are coloured for visual inspection. Different combinations of variable comparisons can be evaluated so that required features are highlighted for interpretation. Blocks are displayed to illuminate the ædominantÆ rock type, according to a formula that may be varied interactively to display the features required by the geologist. This flexibility allows rapid remodelling of lithological distributions, commonly highlighting minor lithological packages not readily visualised in, and interpreted from, drillhole traces alone. The 3D geological model was built from the drillhole datasets and old mine plans utilising standard 3D mining, GIS and database software, with several iterations of plan and sectional interpretation. Near surface bedrock geological interpretations were further constrained by low level aeromagnetic data. The Geospace approach employs an innovative technique for visualisation of the distribution of lithological packages and alteration via block modelling. The method utilises the block model format of data handling as it is considered to be more visible than drilling, flexible enough to incorporate a wide range of data sources, and allows for spatial proximity relationships to be investigated. The method is a simple form of processing large data sets so that results are clearly visible. The calculation is much more rapid than estimation procedures, and does not have any requirement for geostatistical interpretation which is also time consuming. Geospace is not unique to any mine environment software and it is expected to be able to be performed in any system. The proper portrayal of the internal structure of the mineralised body will provide practical input to exploration and mining principally in the areas of resource estimation, exploration vectoring and ore/waste characterisation and may be incorporated with other data to include mine support and mine scheduling.

Jan 1, 2003

Introduction ?MT involves the measurement of naturally occurring magnetic and electric field oscillations. ?The ratio of E/H (wave impedance) is measured as a function of frequency to give resistivitydepth information. ?The ratio of vertical and horizontal magnetic fields (tipper) gives information about the location of (channeled) current systems.

May 1, 2008

By G Guy, J Summerville

Over the past five years in coalmine slope evaluation the application of 3D modelling has increased significantly as software has become more user friendly but also areas requiring evaluation have become increasingly complex. Often simplistic 2D Limit Equilibrium modelling and analysis has been poorly used to solve slope stability issues by back analysis and subsequent forward predictive analysis. A plane strain condition with slope movement perpendicular to the slope strike is assumed where in reality the problem is more complex. This often leads to a misinterpretation of the failure mechanism because the failure mechanism being modelled in 2D does not generally represent the actual failure mechanism observed in the pit, with 2D modelling often oversimplifying a slope. This paper presents a case study where the initial slope assessment and remedial design evaluation was undertaken as a 2D Limit Equilibrium model which led to an overly conservative and costly remedial solution being implemented. Subsequent modelling of the slope using both 3D Limit Equilibrium and Finite Element methods were able to provide a better understanding of the structural complexities associated and correlate well with slope monitoring data to create a more realistic outcome.

Nov 29, 2022

By Andreas Stieben, Pierre Lutomski, Wolfgang Bleck, Martin Fischer

"For steel investigation and development, exact knowledge about the microstructural state is required. The information gained from 2D images often can't properly reflect the real 3D microstructural properties. In order to gain reliable information for meaningful models, simulations and correlations, it is necessary to accompany standard metallography with 3D information, which, unfortunately, is very difficult to access. This article presents a procedure for serial sectioning in combination with light optical microscopy. Only standard metallographic tools are employed in combination with image manipulation freeware. 3D microstructural data were extracted from three multiphase steel grades and in two cases virtual 3D-models of microstructural phases were generated.Three Dimensions Of MicrostructuresSince the invention of steel, craftsmen, inventers and engineers tried to improve its properties and tailor them to the requirements of new developments. For systematic development and enhancement of steels, the capability to investigate its inner structure is highly important, because it represents the linchpin between material production and properties. By having an in-depth understanding how production conditions form the microstructure and also how the microstructural state determines the material properties, steel design can be drastically improved. With this knowledge, microstructures can be designed to provide target material properties and process conditions can be identified that form these structures. Due to the key role of microstructure, the capability to gain accurate information about it is indispensable. It is the task of metallography to access and extract descriptive quantitative microstructural data like fractions, sizes, shapes and distributions of the different constituents. The most commonly used investigation tool in metallography is the light optical microscope (LOM). Besides this tool, additional high resolution techniques like Scanning Electron Microscopy (SEM) or Transmission Electron Microscopy (TEM) have become increasingly important. With these and other available methods, extensive information on the microstructural state of a material can be gained. Unfortunately, most metallographic methods have a major loss of information systematically built in. Analyses of microstructures are usually performed on surfaces, i.e. on 2D areas that emerge by cutting through the 3D material structure. This means, a complete dimension of information is not taken into account. How serious this reduction of information is and how it can affect interpretation of structures is exemplarily demonstrated in figure 1, which displays the planar structure emerging from a random cut through a simple 3D structure. It is very difficult to deduce or even imagine the original spatial structure from which this projection emerged and it is impossible to reconstruct it with absolute certainty without further information. The image has emerged from a random cut through a 3D structure of stacked cubes that is displayed in figure 2. The area shown in figure I is outlined. Although artificially constructed, this example demonstrates how distorted and misleading the view on structures can become by ignoring a spatial dimension."

Jan 1, 2012

By R H. Knight

Production mine geology must be accurate and efficient in order to reduce risk and ensure that ore value and mining operation revenue are maximised. Present grade control practices are commonly based on outmoded and inaccurate 2D geological mapping techniques where spatial relationships are estimated by eye, sketched by hand and projected to arbitrary reference planes. The 3D mapping approach outlined in this paper integrates 3D photogrammetric imagery with implicit modelling techniques to enable more accurate grade control and reconciliation in underground mines. High-resolution stereo photographs are taken of daily ore development headings. Ore contacts are traced directly on a 2D face photo using a stylus and rugged tablet. Area-weighted face grades are estimated and calculated on mapped 2D face planes. In the office, a 3D photorealistic mesh is processed and georeferenced. 2D face mapping data is transformed into its actual 3D location and true 3D mine mapping is performed by digitising oriented 3D polylines representing ore contacts and other geological features directly onto the image surface. Three-dimensional spatial relationships are fixed, eliminating the projection error of traditional 2D methods. Ore envelope and waste solids are modelled within the closed, drift-round mesh. Volume-weighted ore envelope and round grades, as well as round volume and tonnage, are calculated. Ore/waste classifications, grade, tonnage and per cent dilution are quantified per round, visually assessed in 3D and reconciled with short- and long-term models on a daily basis. Updated geological continuity models provide geological guidance in development headings under geological control and accurate 3D structural and form-line mapping improves definition drilling and stope planning. Three-dimensional imagery provides a permanent detailed survey and geological record of mine workings that can be revisited virtually to reinterpret geological ore controls in light of new observations and insights. In addition images can be used to monitor daily production performance, create training scenarios for miners, engineers and geologists and prepare management presentations. This approach adds value to underground mines by improving the accuracy and efficiency of mine geology practices. The method is particularly effective in mines with visually distinct and geometrically complex orebodies, such as those in the Balmat zinc mine located in New York State, USA, which are used to illustrate the method.CITATION:Knight, R H, 2017. 3D mine mapping – improving grade control and reconciliation in underground mines using photogrammetric imagery and implicit modelling techniques, in Proceedings Tenth International Mining Geology Conference 2017, pp 203–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S. H. Lau

Rapid 3D characterization of multiphase mineral particles in a variety of mineral processing applications is described, including: mineral liberation analysis, grain size, mineral exposure analysis, particle damage, and pore network structure for fluid flow simulation in heap leaching. While micro X-ray computed tomography systems (microCTs) have been used for many years, industrial adoption is limited due to a variety of reasons, including insufficient resolution, the general lack of imaging contrast to differentiate different mineral phases within a multiphase mineral particle and the lack of automated 3D mineral processing software. For example, resolution with industrial CTs and desktop microCT is of the order of tens of microns to a few microns at best, depending on specimen size and CT configuration. We describe a novel lab-based X-ray microscope, XRM, which overcomes these resolution and contrast limitations, notably as the industry is going towards finer grains and more complex ore bodies. Using lens-based optics and detectors (similar to its XRM counterpart in synchrotron beam lines), resolution of the lab based system is in the submicron range with contrast better than conventional microCTs. Hence, visualization, differentiation and segmentation of most mineral phases of interest to the industry are now feasible. Coupling these high resolution and high contrast tomography images with a suite of customized 3D segmentation algorithms and analysis software, applications in mineral liberation analysis for process control, particle damage assessment and other mineral processing applications can be achieved. This non invasive 3D technique which requires relatively little sample preparation is currently being considered for coal, industrial minerals, and base/precious metal ores, complementing existing microscopy techniques such as QEMSCAN and MLA for a variety of applications

Sep 1, 2012

By Z Bagheri, E Moosavi

Identifying the exact borders of geological domains and assessing the uncertainty of these borders are crucial steps in resource estimation. This potential field method was designed to build 3D geological models from data available in geology and mineral exploration, namely the geological map and a digital terrain model, structural data, borehole data, and the geologist’s interpretations. The resource evaluation of a copper ore deposit is often performed in three steps: (i) delimitation of the boundaries of the units corresponding to the various geological formations or ore types; (ii) estimating densities; and (iii) estimation of grades within each unit. In simple cases (e.g., a series of sub-horizontal layers), the geometric model can be built using 2D geostatistical techniques (kriging or co-kriging of the elevations or thicknesses of the various horizons) which also quantify the uncertainty of the model. A 3D model of Cu grade is generated using ordinary kriging; however, the indicator kriging method is run to design a 3D model of rock types by incorporating the drilling results. Block models of geophysical and geological characteristics are included in a similar 3D mesh to investigate their relationships in copper mineralisation.

Sep 1, 2021

By Muhammad Zaka Emad, Rangzeb Goraya, Muhammad Usman Khan

"Numerical modeling has been used extensively to assess the stability of surface and underground mines. Tabular, steeply dipping ore bodies are generally mined out by open stoping methods with delayed backfill. Cemented rockfill (CRF) is employed as a backfill material for narrow vein deposits with low production rates. Sublevel stoping methods with delayed backfill are employed to mine out steeply dipping ore bodies. Backfill is exposed to blast-induced vibrations and dynamic loading due to loss of confinement, which could lead to backfill failures. Backfill failures could influence the operating cost of a mining stope and the productivity of the entire mining project. This work shows a detailed overview of the factors contributing to backfill failure. A detailed literature review is presented along with case studies of longhole stoping operations from the Canadian Shield region for this work. The backfilled stopes are analyzed with the finite difference code FLAC3D. The literature review shows that the factors primarily responsible for fill failure are the strength of backfill, stope geometry, mining sequence, and blast-induced vibrations. INTRODUCTION Sublevel stoping methods with delayed backfill are popular in Canadian hardrock and metal mines. Backfill facilitates ground control and greater recovery of ore with pillar mining. It reduces wall slough, thus decreasing ore dilution from adjacent walls. The production of cemented rockfill (CRF) is simple; rock aggregates are mixed together with cement slurry and then placed in a mined-out stope. CRF has a low water content, thus it requires no additional drainage unlike some other backfill. Low water-to-cement ratio enables faster curing rate, hence a faster mining cycle can be achieved (Annor, 1999; Hassani and Archibald, 1998; McKay and Duke, 1989). CRF is generally placed in stopes from the upper sill drift using a truck or a load haul dump machine. Some of the problems associated with CRF are the moderate to high operational cost, the difficulty to get a tight filling, and segregation. Backfill failure is a product of many factors, such as cementation, particle size distribution, placement method employed, water quality, segregation, and blast-induced vibrations. The problem of segregation in aggregates has been observed when aggregate is dumped from a backfill raise (Meech, 2012; Indiana DOT, 2013). Segregation becomes unavoidable when the aggregates are not properly sized (Yu and Counter, 1983; Stone, 2007; Yu, 1989). The exposed backfill zones will contribute to ore dilution due to backfill when subjected to dynamic loading due to fill failures. This paper presents a detailed literature review and numerical modeling results of a mine backfill, along with case studies from longhole stoping operations. The backfilled stopes are analyzed with the finite difference code FLAC3D (Itasca, 2017). The literature review shows that the primary factors responsible for fill failure are the strength of backfill, geometry of stope, sequence of mining, and the vibrations induced by blasting operations."

Jan 1, 2017

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By Jian-bin Xie, Lin-fang Shen, Zhi-liang Wang

"In order to research temperature field for construction of connecting passage in Metro using artificial freezing method, the finite difference software FLAC3D is employed to numerically simulate construction process of connecting passage. During construction, the overall distribution of temperature field around connecting passage, the relationship between soil temperature and freezing time, the distribution and variation for the thickness of freezing wall are studied from the perspective of numerical analysis. The results show as follows: after 55 days’ freezing, the soil temperature surrounding connecting passage is about -24 oC ~ -28 oC, and the minimum thickness of freezing wall is about 4.0m, which is larger than the design value 3.1m. So construction conditions have satisfied to the excavation of connecting passage and pumping station. During the excavation of connecting passage, soil temperature has almost no obvious change and the thickness of freezing wall remains constant mainly. After 45 days’ normal thawing, the temperature of freezing wall rises 12 oC approximately. And the soil temperature rises faster at the beginning of the normal thawing stage. In the whole process of construction, the frozen area is about 5m outside the edge of connecting passage, and the cooling area is about 10m outside the edge of connecting passage. INTRODUCTIONThe first recorded application of the artificial freezing method is on a mineshaft project in 1862, and it has been widely used in foundation pit engineering, subway tunnels, mine shaft engineering and so on (Wang Zhiliang, 2010; Zhang Juanxia, 2012; Qiu Fan, 2007; Zhou Xiaomin, 1999). This method has many advantages of enhancing soil strength; decreasing permeability and adopting various unstable soils (silt clay, sand, gravel, etc.). It has been applied successfully in metro engineering construction in Beijing, Shanghai and Nanjing. According to incomplete statistics, the construction of connecting passage using artificial freezing method accounted for 98% in Shanghai metro (Qiu Fan, 2007)."

Jan 1, 2015

By M. Isac, R. I. L. Guthrie, S. Ge

The Al-Mg-Sc-Zr alloys have shown exceptional potential as structural materials for transportation applications. These alloys have proved to be good candidates to be processed as thin strips via the Horizontal Single Belt Casting (HSBC) process. The HSBC process is a near-net-shape casting technology, which involves casting molten metal directly into thin strips, close to the final product thickness, at high cooling rates. It offers an efficient, economical and environmentally-friendly approach to the production of metal strips. Fluid mechanics and associated heat transfer are important aspects of any casting process, and the novel HSBC process is no exception. Three dimensional Computational Fluid Dynamics (CFD) simulations using ANSYS FLUENT 14.5 were performed, in order to assess the importance and effects of the various operational conditions of the HSBC process. This enabled process parameter optimization. Numerical predictions were validated against experimental casting results.

Jan 1, 2014

By Su-Ping Peng

Three dimensional (3D) seismic exploration has been carried out since the 1980s in the mining district of China, where it has been playing an indispensable role in the high yield and efficiency of coal mining. Unlike oil exploration, this technique uses high density seismic acquisition technology. In recent years, it has focused on wide azimuth 3D seismic acquisition. Evaluation of geometry moved away from depending on folds, azimuth and offset, toward being based upon a focus-ray beam. Conventionally, coalfield 3D seismic interpretation focused on time domain and was based on kinematics information, which is only suitable for less complex geological conditions. To achieve high-resolution processing for the complex topography and structure in coalfields, data processing shifted from poststack to prestack. The means to improve the accuracy of interpretation for complex geological conditions are 1) integration of multiple attributes and multiple disciplines, 2) combination of seismic and geological data, and 3) comprehensive combination of time domain and depth domain data. With the demand for lithological exploration, high-resolution data processing must also take into account the requirements of preserving amplitude in seismic data. Seismic attributes technology, seismic inversion technology, and dynamic tracking interpretation are key techniques in 3D seismic exploration. They greatly improve interpretation accuracy, produce better results in the goaf space description of the coal-bearing strata and coal seam structure, and effectively reduce exploration costs under complicated geological conditions. Therefore, these techniques will be the primary means employed in the future to deal with coalfield complex structure and lithological exploration.

Aug 1, 2013

By M. Wu, A. Kharicha, A. Ludwig

"The droplet formation during melting of a 400 mm diameter electrode is simulated with a multiphase-MHD approach. The computational model includes a layer of slag and a layer of liquid steel. A VOF approach is used for the interface tracking and a potential formulation is used for the electric and the magnetic field. The Lorentz force and the Joule heating are recalculated at each time step in function of the phase distribution. The first results provided by this model are presented.IntroductionThe Electro-Slag-Remelting (ESR) process is an advanced technology for the production of components of e.g. high quality steels [ 1-9]. An alternating current (Figure 1) is passed from a conventionally melted and cast solid electrode through a layer of molten slag to the baseplate. Because of the electrical resistivity of the slag, Joule heating is generated and the slag transfers this energy to ingot and mould surfaces and to the melting electrode tip. The molten metal produced in the form of droplets passes through the slag and feeds a liquid pool from where directional solidification takes place. The slag and the ingot are contained in a water cooled copper mould. As also the baseplate is water cooled, a heat flow regime is imposed that gives controlled solidification, and this results in improved structure characteristics of ESR ingots.This process involves two liquids, a liquid metal and a liquid slag. Each liquid is subject to a phase change due to melting and/or solidification. From a fluid dynamic point of view, the ESR process is clearly a multiphase process, with free interfaces (slag/pool, gas/slag), and with a mixed area (slag and falling steel droplets) [ 10-15].Physically, the development of the heat and mass transfer at the slag/droplet interface is important for the final ingot quality, composition and cleanliness. Visual observations of the droplet formation just under the electrode being melted is almost impossible. Due to the presence of high temperatures, opacity of the materials, and the presence of the mould it is not possible to directly observe the behaviour the slag/pool interface. Although usually assumed flat [1-9], a previous work [10] using a Volume of fluid (VOF) model has shown that the interface shape between a layer of slag and steel layer in a cylindrical cavity is highly coupled with the distribution of the electric current. A full scale simulation of the ESR process using a VOF model has shown that the shape of the pool interface is likely to be non flat."

Jan 1, 2011

By G. Argyris

A number of important studies, ongoing environment monitoring efforts and mining and road construction projects in the lignite based electrical power production area of Amyntaio ? Ptolemais in North West Greece require an accurate and up to date model of the topography. In recognition of the importance of such a model, a project was initiated by the Laboratory of Mining Information Technology and GIS Applications in the Department of Geotechnology and Environmental Engineering of the Technological Educational Institute of Western Macedonia. A massive surface triangulation model was generated from vector data using an optimized Delaunay based method. Combined with aerial and satellite imagery, the triangulation model provides a complete 3D terrain model of the area characterized by high levels of accuracy, detail and realism. The generated model is easy to modify with new data in order to improve its detail and keep it up to date with ongoing earth moving and development operations in the area.

Jan 1, 2008

By C. A. Ingram

The Cigar Lake ore body is a high-grade uranium deposit situated within water-saturated sandstone. In order to extract the uranium ore remotely, ensuring minimal radiation dose to workers, and also to access the ore from stable ground, the Jet Boring System (JBS) was developed. This method of mining involves drilling a pilot hole up through a frozen ore body and utilizing a high-powered water jet to mine out cavities. During the mining process an ultrasonic sensor will be used to provide feedback to the operator, who is located beneath the ore body, as to the dimensions of the cavity. However, more precise data is required to determine final shape, volume, and location of the cavity for mine planning purposes. Selecting a device that will provide sufficient range data in the challenging environment will be vital to optimizing the mining process. Major issues include fog build up and flying debris during mining, and an environment that is wet, dark, and cold A test cavity has been designed and constructed at the Saskatchewan Research Council (SRC) so that a study comparing three different technologies, as prospective candidates for the survey system, can be conducted. The devices being evaluated include a Senix ultrasonic sensor, an MDL Cavity Auto-Scanning Laser System (C-ALS), and a MESA Time of Flight (ToF) camera. The ultrasonic sensor is known to provide range data in foggy conditions but has low accuracy. The C-ALS has been developed for surveying remote cavities but is expensive and does not provide reliable data in fog. The ToF camera provides a high volume of data in a short time period, with potential to provide accurate information in extreme conditions, but has not been tested in a mine cavity application. Iterative closest point (ICP) registration is applied in an attempt to create a 3D point cloud from the scan data and to also compute rotation and translation of the ToF camera. This paper presents an overview of the challenges involved in conducting a survey within a JBS mined cavity, the analysis used to determine the suitability of each device, and the data collected from the test cavity.

Aug 1, 2013

By Jean François Stumper

This paper presents the TMT “3D TopScan” profilemeter, which is a Radar-based profilemeter that measures the total burden surface within a few seconds and on a continuous basis. This equipment is based on an electronically steered solid-state radar scanner, such that a very large amount of surface data is collected within short time intervals. These new electronically steered antenna systems are the key to meet the demands for both accuracy and speed. The TMT probe is installed at a fixed location at the top cone, such that it does not interfere with the charging, enabling a continuous measurement and a compact design.Blast furnace charging optimization can be achieved based on its measurement data. The burden surface is continuously measured every few seconds, enabling the blast furnace operator to detect any details including asymmetries or irregularities in the surface pattern. A variety of process analysis tools are available. Due to the continuous and fast measurement, the burden descent speed can be supervised without process interruption on an ongoing basis. More accurate process models (layer models) than ever are obtained which fully consider the unsymmetries.This technology, developed by TMT Tapping Measuring Technology, is successfully in operation at Salzgitter Flachstahl GmbH at their blast furnace B. The probe and the data evaluation tools combine today’s technological capabilities in measurement technology with the practical requirements of blast furnace operation.

Aug 16, 2017

By Stephen G. Hardcastle

3D-CANVENT is a software package that integrates advanced computer aided design (ACRD) true 3D graphics with a mine ventilation simulator. The package runs as a Windows(tm) application to access its printer drivers environment and does not need third party CAD software. It is composed of two primary modules: DMVENT and MINEDESIGNER. DMVENT is a traditional Fortran coded Hardy-Cross iterative ventilation network solver written in 1980 with thermodynamic capabilities. This module is relatively unchanged with the traditional data input options for branch type, specified or calculated resistances, fixed flows, and fixed or variable pressure fans. MINEDESIGNER is the graphics engine that optimizes the ventilation design process. It performs the front-end transformation of input data entered in the graphical interface into the correct format for the solver. At the back-end it reconverts the historically standard tabular data output from the solver into an easily viewed graphical format. ACRD features of MINEDESIGNER are used to generate a 3D wire-frame node and branch network of the mine's ventilation system. The network can be displayed in up to 4 views orientated to XYZ planes or a 3D view. All the views have zoom, pan, slice and rotate options. The graphical interface efficiently permits data entry and editing via a mouse with pick-and-point item selection. Branches can be found or added with "search" and "join" options. Visual interpretation is enhanced by the 16 colour options for branches and numerous graphical attributes. Network locations are readily identified by alpha-numeric names for branches, junctions and fans, and also the logical numbering of junctions. The program is also readily expandable for pollutant simulation and control/monitoring applications.

Jan 1, 1995

By J. Wendt, P. R. Sahm, T. Uloth, M. Weck, F. Foertsch

"The FEM program systems CASTS (Computer Aided Solidification TechnologieS) (1) and FINELF (FINite ELement Frontal Solver) are used to optimize a thin walled die casting. After a short description of the programs it will be worked out how to use them not only for simulating solidification processes but also for optimizing the design of workpieces. The calculations will be done for an automobile's support bracket which is manufactured in a well known car factory in Stuttgart, FRG.IntroductionAt the Aachen Foundry Institute the software package CASTS was developped to simulate solidification of castings. In order to optimize the whole manufacturing process it does not appear sufficient any more to take into account only the specific aspects of casting. For instance one has to consider additionally the stress situation under service load. For this reason the Foundry Institute together with the Aachen WZL-Institute (Machine Tool Laboratory) and the car factory mentioned above started to probe into a first step in that direction. Figure 1 shows the support bracket which shall be optimized."

Jan 1, 1986

By Bo Hyun Kim, Mark K. Larson

Although techniques and practices of mining are highly advanced, coal pillar bursts or bumps continue to occur. Many uncertainties remain because of the highly anisotropic characteristics of coal seams that are associated with geologic structure and the mining-induced spatial redistribution of stress in coal pillars. Thus, to prevent fatalities in underground coal mining, continuous efforts are required to better understand the catastrophic failure mechanisms in coal mines. In this study, 3DEC modeling in conjunction with the Discrete Fracture Networks (DFNs) technique was performed to better understand the true anisotropic behavior of the specimens acquired from a bump-prone underground coal mine. The spatial characteristics of the dis- continuities (i.e., cleats and bedding planes) as input data for the 3DEC model are estimated based on the results of the laboratory tests and field observations. The DFNs explicitly generated the coal seam that was poorly or well cleated, indicating the different spacing between cleat apertures using the probability distribution functions for fracture density (or frequency) and size. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) are also considered by Monte Carlo simulations. Simulation results of laboratory tests using the 3DEC model and DFNs technique agreed well with the results of the laboratory tests. These calibrated results can be used as we seek to evaluate bump risk by modeling at field scale.

Jun 25, 2024