Search Documents

By Louis A. Panek, John A. Stock

A flat slot is created in rock to cause stress relief effects in a pair of hydraulic borehole pressure cells (previously installed in drill holes above and below the slot ) , which act as sensing devices . This relief is annulled by repressuring the slot by means of a flat hydraulic cell . The slot pressure at annulment is taken to be the existing ground stress at right angles to the plane of the slot . A number of trial installations in the rib of a mine drift showed that for a valid determination of ground stress the sensing devices that respond to relief and repressuring must be within a specified zone close to the pressure transmitter ; otherwise the indicated ground stress may be excessive . By using an additional pair of borehole pressure cells , installed a few feet away , the existing rock stress can be redetermined at intervals , irrespective of a change of stress intensity subsequent to the initial installation . Based on these findings , equipment and procedures have been developed that make possible the installation and operation of a permanent rock stress monitoring station for observing mining - induced stress changes . The station consists of a 12 - in - wide hydraulic pressure cell cemented in a flat slot and four 2- by 8 - in flat hydraulic pressure cells in nearby drill holes . All drilling for the installation can be done with an air leg drill and conventional bits . Once the installation is completed , all required information is obtained by Bourdon pressure gage readings . The apparatus is simple , relatively inexpensive , and reliable under operating conditions in a wet mine . Unlike most methods of rock stress determination , this scheme permits periodic remeasurement of absolute rock pressure over several years , without additional drilling or instrumentation . Similar to other flat slot procedures , stress measurements are obtained without making auxiliary tests to determine elastic

Jan 1, 1964

By R. J. Lytle

INTRODUCTION Prior to excavation in soil and rock, it is useful to know the subsurface structure. This is important information both for safety and for equipment scheduling reasons. It is useful to know whether parts of the subsurface might be potentially troublesome or of different character than is generally thought present. By using geophysical probing, it is possible to infer the location and size of these unusual regions. The ground structure is commonly estimated from core samples taken from boreholes. These cores give a detailed knowledge of the structure in the borehole. However, knowledge of the structure exterior to the borehole can only be extrapolated from core data. By using seismic and electromagnetic cross-borehole geophysical probing, remote probing can be used to sense the region exterior to boreholes. A recent advance has significantly improved the state-of-the-art for defining the ground structure between boreholes. This new procedure utilizes large amounts of data and provides a detailed picture of the subsurface. The data processing algorithms used are similar to those in medical imaging of the human body using x-rays, a science called x-ray tomography. This imaging of the ground is called geotomography, which is a shortened acronym for geophysical tomography. Several examples of geotomography applied to imaging ground structure are presented. Our approach has been to probe the ground with electromagnetic and seismic waves. We map the region of interest with signals transmitted between multiple source and receiver pairs lowered in boreholes on opposite sides of the region (Figure 1). The received signals vary according to the transmission properties of the media

Jan 1, 1979

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By R. A. Bullivant

Roger Bullivant Piling Limited has started 1992 with the introduction of the CONE PILE into its range of precast concrete foundation techniques. Since the establishment of its Piling Division ten years ago, alongside the original Underpinning Company, a commitment to innovated development has seen a steady growth in Roger Bullivant's activity in piling, ground treatment and general foundation engineering. Over the last four years, £1.2 million has been invested by the Bullivant Piling Division into research and development in the field of precast piling and other foundation systems. The goal has been to develop economically attractive systems tailored to our clients design requirements and, wherever possible, unique to Roger Bullivant Piling.

Jan 1, 1992

By William P. Blake

(Canal Zone Meeting, November, 1910.) A DEPOSIT of manganese-ore near Tucson, Ariz., merits notice by reason of the peculiar form in which it occurs, and as a striking. example of ore-deposition by vadose upward capillary flow of metal-bearing solutions with concentration at the surface of the country-rock. This deposit occurs at the northern end of the Coyote mountains, about 40 miles west of Tucson, upon the outcropping beds of porphyritic rock, which appear to be partly-metamorphosed strata of volcanic tufa, probably of late Secondary or of Tertiary age. The strata dip northward at a low angle, and present a series of basset-edges in parallel lines of outcrop, east and west, facing the south and extending over many acres. Successive groups of these outcrops, from 5 to 20 ft. in breadth, are coated with oxides of manganese in lustrous black films and crusts, shining in the sunlight like polished ebony, and covering the whole surface of the rock above the soil. Seen at a little distance, these croppings look like solid ledges of massive and pure ore; but closer inspection and a few blows of the hammer reveal their true nature as a superficial coating allied in origin to the blackened shining surface of rocks exposed in desert-regions, familiarly known as " desert paint" or "desert varnish,"' similar to the phenomena described by me in a former paper, but much thicker and heavier. * By reason of the death of the distinguished author, this communication, probably his last communication to technical literature, is published without revision of the proofs by him. A term first given y G. K. Gilbert. See Rocks, Rock-Weathering, and Soil; by George P. Merrill, p. 256 (New York, 1897). Superficial Blackening and Discoloration of Rocks, Especially in Desert Regions, Trans., xxxv., 371 (1905).

Sep 1, 1910

By Henry Kreisinger, J. F. Barkley

This book is one of a series of publications being issued by the Bureau of Mines for the purpose of disseminating information in regard to the methods by which the fuels in this' country may be used most efficiently. A knowledge of the temperature of the gases in boiler settings and in other commercial apparatus using heat tends to develop improved designs of apparatus and better methods of operation, thus reducing waste of fuel. The following pages present, for the benefit of those designing, operating, and testing such apparatus, information as to the accuracy of temperature measurements made under certain conditions and the corrections that can be safely applied.

Jan 1, 1918

A great range of contacting equipment is used in solvent extraction. However, a tower filled with a regular packing offers many advantages in the direct extraction from slurries. A study was made of the flow of a dense slurry through a packed tower in which the continuous phase was kerosene. The grid type packing, which was preferentially wetted by the slurry, had slats inclined at an angle of 30¦, to the horizontal. On the sur- face of the slats there were uniformly spaced longitudinal indentat- ions. These were of a height slightly less than the film thickness and divided the slurry discharging from the bottom of the slats into a number of uniform streams. When slurry entered the tower it was distributed by means of a troughs and weirs type of distributor. Because of the relatively high slurry velocities that occur at the entry region, it was necess- ary to have the distributor and the first two grids above the solvent level. The interface at the bottom of the tower was located at the mid-point of the bottom grid, so that the slurry entered the interface as a continuous film across the full width of the slats. Using the above system, stable flow with low entrainment was achieved at slurry flow rates of 3.4 mis/cm/sec. This would be equivalent to a flow rate of 177 gallons per minute through a tower of cross-section 4 ft 4 in. by 4 ft 10 in., or 1200 tons per day of solids of specific gravity 2.6 when the pulp density was 65 per cent. Previous tests indicated that a total tower height of about 30 ft would be required for a recovery of better than 99 per cent.

Jan 1, 1969

By J W. Muir, N Bedford

Hong Kong is one of the most rapidly developing cities in the world. With constant population growth and limited opportunities for space, the development of a fast and effective underground public transportation network is essential. Hong Kong’s Mass Transit Railway (MTR) Corporation is currently undertaking several large underground expansions to its existing network. Much of the excavation will be carried out using the drill and blast excavation method.Drill and blast excavation is common in Hong Kong and with the continued development of underground infrastructure the use of the drill and blast excavation method will increase. Although an effective method of excavation, the blasting vibrations caused during construction can have an adverse impact on surrounding structures and impose disruption on the local community.In order to minimise the risks associated with blasting vibrations, and to demonstrate that the impact on local stakeholders will remain within acceptable limits, it is generally necessary for a contractor to submit a blasting assessment report for approval by government authorities before blasting may commence.Continued increases in population density will force more infrastructure to be constructed underground. Tunnels and caverns are increasingly excavated in closer proximity to critical sensitive receivers. This leads to greater potential impacts on the community, tightening constraints on contractors and a higher level of confidence required for approval authorities. Finding a balance between the needs of the community and rising construction costs becomes more challenging.This paper presents a case study on how the blasting assessment report process has been successfully implemented for a major MTR project situated in a densely developed area of Hong Kong. It describes several methods of assessing blasting vibration impacts, innovative uses of blasting for excavation and the mitigation measures employed to provide the best outcome for all project stakeholders.CITATION:Bedford, N and Muir, J W, 2014. Blasting vibration assessment and innovative blasting methods in high-density urban environments, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 9–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Javier Enrique Basurco Cayllahua

In this work, a gram-positive bacteria was used as biosorbent to elucidate the aluminum load capacity under different conditions related to metallurgical and chemical plants. The sorption data followed the Langmuir, Freundlich, Dubinin-Radushkevich isotherms. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Dubinin-Radushkevich model fits better the aluminum biosorption data. The maximum sorption capacity was found to be 41.59 mg.g-1. The maximum removal of aluminum was 95% at pH around 5. The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). This study indicated that the R. opacus is an environmental friendly biosorbent.

Jan 1, 2009

By P. D. Laverty

This report describes a processing method developed by the U.S. Bureau of Mines to produce high-quality flake graphite from the steelmaking waste known as kish. The kish produced by current steelmaking practices is a mixture of graphite, desulfurization slag, and iron that is skimmed from the molten iron feed to the basic oxygen furnace. It is estimated that the graphite content of kish discarded by U.S. steel plants is more than sufficient to meet the total U.S. demand for flake graphite. That need is now filled by natural graphite from foreign sources. Kish was treated by a combination of screening and hydraulic classification to produce a concentrate containing greater than 70 pct graphite. Leaching of the concentrate with hydrochloric acid solution gave a graphite product with 95-pct purity. An optional secondary leaching operation with hydrofluoric acid produced graphite with a purity of 98 pet or greater. The flake size of graphite from kish ranged from 10 mesh down. Evaluation of test samples by industrial graphite users indicated that kish graphite is a suitable substitute for the natural material for most uses. A process flowsheet and material balance for pilot plant design are presented.

Jan 1, 2010

By C. W. Owings

"Coal may be and has been hauled safely at approximately the same cost with permissible2 storage-battery locomotives as with trolley, cable-reel, crab-reel, or nonpermissible storage-battery locomotives. While in general, thinking mining men readily admit the relative safety of the permissible storage-battery locomotive there are some persons who question the safety of this type; however, the greatest opposition to the widespread use of storage-battery locomotives is from those who believe them to be more expensive to operate and to be more expensive in first cost than the trolley or cable-reel locomotive. Data collected during a comprehensive study- of storage-battery and wired transmission of power in some Pennsylvania and West Virginia coal mines indicate that there is but little difference between the cost of hauling with cable-reel or with storage-battery locomotives. It would appear that if this fact were mere generally known mine operators of the more progressive type would install such equipment and avail themselves of greater safety in hauling coal.The need for greater safety in haulage in coal mines is readily understood when it is considered that during the 12 month period, July 1, 1929 to June 30, 1930, trolley or cable reel gathering locomotives caused four explosions in which 407 lives were endangered, 11 persons were injured, and 30 lives were lost. Still another disaster was averted by the vigilance of a fire boss, who discovered a stratum of gas 3 feet thick at the top of an entry into which a gathering locomotive was about to enter. Other explosions not resulting in any fatality probably have not been reported. In addition numerous fires have been caused by trolley or cable-reel locomotives, and these fires probably would have been avoided had permissible storage-battery locomotives been used."

Nov 1, 1930

By Robert J. Hundhausen, Robert M. Gammell

"INTRODUCTION Several mining properties in the Pine Creek area of the Coeur d'Alene mining region of Idaho were examined by engineers 3/ of the Bureau of Mines in 1942. As a result, a broad program of exploration was recommended for the area, particularly in the eastern end, where chances for the discovery of new ore shoots seemed favorable. This report describes the work done and the factual information obtained by the Bureau of lanes.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell Be Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch,. C. C. Ralston, chief, analyzes samples and performs beneficiation tests.The exploratory work at the Sidney mine was part of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. Field work was under the direction of R. M. Gammell.Chemical analyses included in this report were performed at Reno, Nov., under the direction of A. C. Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines. The ore-dressing tests were made under the direction of S. R. Zimmerley at the Bureau of Mines laboratory in Salt Lake City, Utah.The cooperation and assistance given by the owners of the Sidney Mining Co. is gratefully acknowledged."

Feb 1, 1948

By Robert Alfred

This paper is one of a aeries being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included if available. In addition to descriptions of equipment and methods used the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made, This paper is particularly concerned with the operation of the Liberty quarry and plant of the Campbell Limestone Co, The plant is in Pickens County, adjacent to the main line of the Southern Railway, and is about 18 miles west of Greenville, S, C. Access also is available by United States Highway No, 123, The company's main offices are at Knoxville, Tenn.

Jan 1, 1958

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used 1n this report are divided into two components for individual analysis--(1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations. The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By Robert A. Pond

Heavy (exceeding 35 tons) roadheaders have not seen much use in the United States, but are used extensively in Europe to excavate many types of underground openings in civil and mining applications. Early models of roadheaders were light and suitable only for utility excavation such as drift enlargement or chamber excavation, unless the ground was very soft and easily cuttable. Frontier-Kemper Constructors, Inc. is now using a 45-ton roadheader to excavate two mine slopes in Kentucky and a 70-ton roadheader to excavate a long decline at a new mine in Utah. Results to date indicate that heavy roadhead machines are an effective alternative to both conventional excavation and full-face boring machines in many cases; and where circumstances are favorable are a superior choice. This paper concentrates on applications in the mine development construction industry, but the conclusions are no less valid for civil construction.

Jan 1, 1983

By Th. G. Sahama

This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 and Lives the result: of a thermodynamic attack on the problems of stability end paragenoses. Although some data are lacking, satisfactory agreement with mineralogical and petrological observations is indicated.

Jan 1, 1949

This modern plant was installed with the object of treating all oxide ore and payable dump material by the cyanide process.The plant is located on a ridge on the eastern side of Linda Gully. The mill -site has a slope to the south of 1 in 4.The new plant is of steel and concrete construction and was specially designed to suit the climatic conditions which exist at Mount Morgan.THE COARSE CRUSHING PLANTThe ore received from the, mine is dumped into a 600-ton steel bin which is commanded by a 3 ft. 6 in. gauge railway,The mine ore is conveyed by steam locomotives in rakes of five self-dumping 7-ton railroad cars. The dump material is mostly loaded by bull-dozers and conveyed to the binsin large motor lorries. Located on the top of the bin is a heavy railroad grizzly having 12-in openings through which all ore must pass.The flow of ore from this steel bin is controlled by a No. 7D 3-speed Ross chain feeder. It should be mentioned here that, although the bottom of the steel bin is inclined at an angle of 45°, it has been found, owing to the clayey nature of the oxide ore, that the live capacity of the bin is only about 50% of the total capacity.

Jan 1, 1939

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By R G. Moreby

The purpose of this paper is to provide the rationale for decision making when considering the use of three heading gate roads in Australian underground coal mines.There are currently 30 underground longwall mines in Australia with all but two employing two heading gate road longwall layouts. The volumetric capacity of these two heading ventilation circuits is evidently viable in typical block lengths and in low to moderate gas regimes. However, in gassier regimes, potential longwall production rates of 10 Mt/a, and or where block lengths are being extended to well beyond historical norms, a conventional two heading U circuit may not be adequate. Other than seam gas emission, block length and production dependent heat loads together sealed area management requirements also have to be considered.The two mines currently employing three heading gate roads have the opportunity to revert to two headings at any time but, based on operational experience to date, have not done so due to the consequential reduction in gas management capacity and lower production rates associated with gas delays and limitations on tailgate access.Although there are a number of alternative two heading longwall circuits available and employed worldwide, the custom and practice of promoting inert goaf atmospheres in most Australian coal mines to mitigate the risk of catastrophic gas explosions and spontaneous combustion often prevents the use of gas loaded bleeder systems. In this respect, Australian underground coal mines may be considered the safest in the world.The current situation is that three heading gate roads have been proven successful in Australian conditions, albeit at additional cost, where two heading ventilation circuits cannot manage net seam gas emission to the ventilation system at the production rates required. In this respect, a further important driver for decision making is the short to medium term value of CO2-e emission taxation in Australia.CITATION:Moreby, R G, 2013. The rationale for use of three heading gate roads in Australian underground coal mines, in Proceedings The Australian Mine Ventilation Conference , pp 13-26 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013