Search Documents

By G. Adachi, K. Machida, T. Ozaki, K. Murase

The chlorination rate with CCl4 was unexpectedly slower than carbochlorination using chlorine under the same reaction conditions. Chlorination with CCl4 was topochemical and the amount of monazite reacted after different periods suggested that the kinetic control step was the reaction between CCl4 and the monazite core at the interface. The kinetic order of the reaction was 0.5. The presence of a complex former, AlCl3, promoted the chemical vapour transport of rare-earth chlorides as complexes

Jun 18, 1905

By S. E. Cook

This article uses the case of the Royal Bafokeng Nation to argue that royalties and dividends from mineral resources, if managed well, can provide direct benefits to the surrounding community even while the state collects its share of mining revenues through taxation. The key to this model is the effective management of the resource income flowing into community coffers. Where some of this income may fund urgent interventions in the community, a portion of the income can also be used to establish an intergenerational wealth fund to meet the needs of future generations. As a depleting resource, minerals like gold and platinum are not a sustainable source of income, and must be replaced over time by more regenerative income streams. These strategies and dynamics are manifest in the Royal Bafokeng Nation?s status as both community and quasi-municipality, a labour hosting and a labour sending community, a mine operator and a mine owner. The Royal Bafokeng Nation also owns one of South Africa?s largest community-based investment companies, which channels revenue derived from platinum deposits into a broad investment portfolio that in turn funds an aggressive social development program for 150,000 people living in twenty-nine rural villages.

Jan 1, 2013

By S. K. Shaha, W. Kasprzak, D. L. Chen, J. Friedman, F. Czerwinski

The role of solutionizing conditions within the T6 heat treatment of the cast Al-Si-Cu-Mg alloy with micro-additions of Zr-Ti-V was assessed in terms of their influence on microstructure and mechanical properties. As a solution treatment, a single step process at 485 and 510oC and a two-step process at 510 and 525oC for varying time intervals from 0.5 to 9 h, were examined. In all cases, solution treatment was followed by isothermal aging at 150oC for 100 h. The microstructural analysis showed that the solution treatment changed the eutectic silicon morphology from needle-like, present after casting, to spherical shape in the T6 state and that the extent of changes was strongly influenced by temperature and time. The Cu- and Mg-rich phases completely dissolved during solution treatment while the Fe-containing phase, Al8Si6Mg3Fe, remained partially in the microstructure. The Ti, V and Zr containing phases, Al13Si2Ti3Zr and Al3Si26FeTiV10, present in as-cast state, were partially dissolved during solution treatment, reducing their size by 10 - 48%. The studied alloy reached the maximum ultimate tensile strength of 335 MPa and yield stress of 303 MPa for two-step solutionizing with a total time of 4.5 h. It is concluded that the two-step solution treatment resulted in higher tensile properties than the single-step process.

Jan 1, 2015

By H. S. Price, F. N. Kissell, R. C. McCulloch, J. C. Edwards

"The methane em1ss10n from deep coalbeds which are actively mined is a serious problem facing the mining industry today. Pinpointing the source of methane and predicting the emission of this gas from these coalbeds is necessary if preventive techniques are to be effectively used to control methane emission. In general, because most coalbeds have water associated with them, the system to be studied may be either single-phase (methane gas) or two-phase (methane and water). Because coal mine geometry is complex and the fluids have variable properties as functions of pressure and methane concentration, the differential equations describing the flow of methane and water are not amenable to analytic solution, but must be solved numerically using high-speed computers. This paper presents the development of such a complex mathematical model along with some preliminary applications of the model to methane emission from one- and two-dimensional coalbeds with and without water present."

Jan 1, 1973

Interest in the potential use of high-density, thickened tailings has recently increased significantly. Reasons for considering this new technology vary across projects, but commonly include the need to conserve water, perceived lower risk of catastrophic failure, potential easier closure, or even reduced overall costs. As with any new technology, there has been some tendency to overstate its potential benefits. This paper reflects on whether or not the potential benefits that have been attributed to paste and thickened tailings have been realized. Using a grading system, thirteen benefits that were ascribed to the new technology some years ago are evaluated. Data is taken from case studies, and it is suggested that the key proven benefits appear to be reduced operating costs in some cases, reduced wall-building costs, and reductions in water consumption. One key potential benefit that has not been universally achieved is a reduction in the footprint of the tailings facility. Reports in the literature highlight the sometimes confusing nature of trade-off studies. Unless full life-of-mine costs are considered, these studies can be misleading and incorrect. The need to establish a consistent basis for comparative studies is discussed.

Jan 1, 2012

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By Albert Sauveur

THE senior author of this paper has expressed the belief that when gamma iron transforms into alpha iron on reaching the A3 point, each gamma grain does not change bodily into one or more alpha grains but that the alpha phase forms first at the boundaries and along the crystallographic planes of the austenite grains.1 To quote: On cooling through the point A, at about 900° C., iron passes from the gamma condition to a. new allotropic form generally designated as alpha. This transforma¬tion, however, is not instantaneous. There are good reasons for believing that it begins at the grain boundaries and along the octahedral planes of the crystals and that it progresses until each grain of gamma iron is changed into a grain of alpha iron, the resulting structure being similar to that of gamma iron. Were it possible to retain at room temperature pure iron but partially transformed, it seems probable that a Widmanstättian structure, or rather, as later explained, a martensitic structure would be observed (Fig. 1), consisting of alpha iron at the boundaries and at the octahedral planes, and of a groundmass of gamma iron. In order to confirm, if possible, the accuracy of that view, a number of experiments were conducted. Polished samples of electrolytic iron were heated in a vacuum, maintained in the gamma range for several hours and quenched in different media. It was hoped by such means to produce and retain on the polished surfaces a pattern which would reveal the mechanism of the allotropic transformation. The samples were placed in evacuated quartz tubes, heated to 1000° C. and held 2 hr. at that temperature. The tubes were then immersed in the quenching bath. Iced brine and liquid air were used first. The polyhedral austenitic structure existing at the time of immersion was very clearly revealed (Fig. 2). This is generally ascribed to iron volatilizing at the grain boundaries.

Jan 1, 1929

By J. H. Potgieter

The method used to assess the reactivity of lime was evaluated to gauge it usefulness as a quality control tool. The effect of particle sizes, different lime and water masses for a fixed s:l ratio and the same for various s:l ratios on the reactivity values obtained, were investigated. An attempt to introduce the amount of grit produced during the slaking reaction as an additional measure of limeís quality and reactivity, proved to be unsuccessful. It was also found that the relative amount of lime slaked during the different tests was independent of the reactivity value of the lime. The investigation confirmed the usefulness of the accepted test procedure as are liable method to measure the reactivity of lime, despite various reservations expressed from a theoretical point of view.

Jan 1, 2002

By T. F. Mitchell, J. V. Batty, R. R. Wells, R. Havens

"INTRODUCTION )ne of the most important wartime activities of the Bureau of Mines was the search for new sources of minerals necessary to the prosecution of the war. As a part of the investigation of strategic mineral deposits in the United States under the Strategic Minerals Act (Public 117, 76th Cong., 1st Sess., Ch. 190), examining engineers of the Bureau of Mines investigated and sampled various deposits of chrome ore in California, Idaho, Montana, Oregon, and Washington, and those deposits that warranted further study were explored by diamond drilling, trenching, and drifting, as re¬quired. During these investigations, samples were submitted to the Ore Dressing Section of the Salt Lake City Station for metallurgical testing. This paper gives data summarizing results obtained from laboratory ore-dressing studies of the chrome ores submitted.Although the deposits range widely in geographical location, the mineral occurrence of all of them is strikingly similar. Chromium, in all of the ores tested, is present as impure chromite or chromium spinel. Although pure chromite (FeCr204 or FeO.Cr203) contains 68 percent chromic oxide, the iron may be replaced in varying amounts of magnesium, and the chromium may be replaced similarly by aluminum and ferric iron. In studying concentration methods as applied to chrome ores, the composition of the chrome mineral is of fundamental importance, because it is manifestly impossible to produce a high-chrome concentrate from a low-chrome chromite by any mechanical process.In all but one of the ores, the gangue material consists of olivine or altered olivine minerals such as serpentine, antigorite, and chrysotile. The exception, the Antelope or from Montana, has a gangue chiefly composed of actinolite, chlorite, and talc."

Jun 1, 1947

By G. Duncan

Distinct trends in grinding mill technology have emerged in recent years. In an effort to optimize overall mill performance for the needs of the End User, broad measures of logistical speed, process flexibility, operational risk, and overall costs now exert greater influence on the specification of grinding equipment. As a result, innovative alternatives to conventional grinding mill structures, supports, drives, feed, and discharge configurations are now being offered and selected with greater frequency. This paper investigates these trends in grinding mill technology, utilizing optimization and decision-theory techniques. In particular, the paper considers how specific advances in process design, product engineering, manufacturing techniques, and mining operations continue to relax technological constraints, enabling further mill innovation. In this context, a methodology is presented, illustrating how proper selection and specification of grinding mill components and configuration can target an optimization of the four End-User performance measures listed above..

Jan 1, 1999

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

By Lathrop E. Roberts

The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of Which it tends to form a layer of highly viscous "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and Van Arsdele have shown that the inclusion of grills of matte in the slag is also at tires very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in any laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slag as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even if only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separations from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and when present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by such elements as vanadium and molybdenum.

Jan 1, 1931

By Sukru Sumer

East Pit Lake is an artificially created lake that resulted from the remediation and reclamation of surface coal mining operations at TransAlta Utilities' Whitewood Mine in the Wabamun area west of Edmonton, Alberta. The original excavation resulted from the creation of a mine end cut at the northern extent of the mining operation. The area of the surficial drainage basin that feeds East Pit Lake was relatively small. Therefore, most of the inflow and outflow from the lake would result from regional ground water flow. There was a concern about the lake's ability to provide a suitable habitat for a sportfish population. To determine the final recovered water level and rates of recovery, a two-dimensional ground water flow model was used. Data supplied by nested piezometers in and around the mine were used to calibrate the computer simulation and assess predicted recovery.

Jan 1, 1995

By D Clarke, I Minniakhmetov

The Olympic Dam deposit is truly a world-class IOCG-Ag deposit, the world’s fourth largest deposit of copper and the world’s largest known single uranium deposit. Traditional and non-traditional methods have been used to accurately model the geology and mineralisation of the Olympic Dam deposit. Conditional simulation models have long been used as the most robust method for estimating risk and uncertainty in mine planning decisions at other mines around Australia and the world. There are many challenges associated with simulating the Olympic Dam deposit at a selective mining unit size sufficient for underground mine planning purposes. These include the size of the deposit, resulting in hundreds of millions of grid blocks; the disseminated nature of the zoned sulfide mineralisation. And lastly the direct relationship of the relative abundances of the sulfide mineral species that are crucial to the Olympic Dam smelter performance. Several geostatistical techniques have been utilised in the workflow for the Olympic Dam Conditional Simulation model to address these challenges. The key techniques are: • Projection Pursuit Multivariate Transform to de-correlate the main elements before simulation. • Pluri-Gaussian implicit boundary simulation method to simulate the mineralisation domains. • Spectral simulation method of de-trended and de-correlated attributes with account of local varying variance. The resulting conditional simulation models have been validated against histograms, grade-tonnage curves, cross-plots and assessed for variogram reproduction. This paper presents how the final conditional simulation models compare to benchmarking models created using alternate estimation techniques of ordinary kriging and local uniform conditioning. It also presents a validation process using historical samples to test final estimate accuracy of the simulation models.

May 24, 2023

By F. T. Cawood

The definition of mineral rents has historically been somewhat unclear, but a growing understanding of the source and composition of the revenues that comprise these rents mean that they can be more easily identified and quantified. Furthermore the way in which the flow of the rents from mineral developments are captured and then distributed has been a point of contention amongst the various stakeholders. Investors, the host government, the resource owners, environmental interests, indigenous groups and land owners are identified in this paper as the principal participants in mineral development and while each is entitled to a portion of the rent, the size of their portions will differ. A competitive rent-sharing model for southern African countries has been established and indicates how the range of stakeholders could be rewarded for their contribution. Acceptance of the sharing ratios amongst the recipients is a function of their understanding of the size of the rent and their position in the hierarchy of stakeholders. At first glance investors appear to receive the largest share of the rent, but they disburse some of the rent to hidden costs, which when all is said and done, means that investors and host governments retain approximately equal shares of the mineral rent. Both the investor and government are faced with the dilemma of how to equitably distribute the rents they have captured to minority stakeholders. Government captures corporate tax, mineral royalties and a wide range of subordinate taxes, but is required to construct policies that will ensure distributional equity among the various levels of government as well as among the provinces that comprise the country. Investors will have to ensure that a portion of the rents they capture are diverted to other stakeholders namely resource owners, environmental interests, indigenous peoples groups and the landowners. This paper identifies the major recipients of rent and provides some indication of equitable distribution ratios for mineral wealth among them?a first step in ensuring that mineral development is compatible with long-term sustainable development and in the best national interests.

Jan 1, 2002

By J. D. Aitken

"DEFINITION OF THE REGIONTHE REGION considered in this paper is bounded on the south by the 60th parallel, on the north by the Beau-fort Sea and Amundsen Gulf, on the east by Archean rocks or by highly deformed Proterozoic rocks of the Canadian Shield (certain weakly deformed Proterozoic strata being regarded as belonging to the Great Plains), and on the west mainly by the Mackenzie and Richardson Mountains.Only the unmetamorphosed strata of the region are considered; that is, the geology of the crystalline basement is ignored.SIGNIFICANCE OF THE REGIONThe region is significant from three points of view -namely, the economic, the scientific and the social. It constitutes 46 per cent of the area of the Western Canada Sedimentary Basin."

Jan 1, 1970

By C. C. Miller, A. R. Belyea, C. H. Herty, E. B. Burkart

The removal of sulfur from steel has been studied by many investigators, but the quantitative relationships between the factors involved have not been determined. This is undoubtedly due to the number of variables encountered in practice, an attempt to study any one reaction or relation being affected by other reactions the relative importance of which cannot be estimated. The factors that affect the extent of removal of sulfur in the basic open-hearth process are generally considered to be: 1. Basicity of the slag: (a) Iron oxides in the slag; (b) carbon in the metal or carbide in the slag; (c) temperature. These factors affect the reactions: FeS + CaO = CaS + FeO FeS + CaO + C = CaS + CO + Fe. 2. Amount of sulfur in the gas. 3. Amount of manganese in the metal. The factors which affect the rate of removal of sulfur include, in addition to these: 4. Fluidity of the slag: (a) Normal changes in fluidity with temperature; (b) changes in fluidity because of the addition of special reagents such as fluorspar. 5. Agitation of the bath. Within the past two years, two papers have been presented dealing with the influence of sulfur in the gas on slag and metal. Nead' has shown that if a gas high in sulfur be used for heating, the metal and slag will absorb sulfur. Whitely2 concluded from his experiments that if a

Jan 1, 1925

As ore deposits become finer grained the requirements for regrinding before cleaning or leaching have increased substantially. Despite this increasing need, there is no standard test to predict grinding energy requirement below 70 microns. The standard Bond Mill test applies for coarser ball milling, but is not appropriate for stirred milling with fine media grinding to 70 microns. With no industry -standard test, the energy requirement is often made on the basis of supplier estimates or benchmarking against similar applications. Yet suppliers use vastly different scale-up methods which result in widely different energy estimates. Estimates can differ by 100-300% even for similar mills. This must result in serious errors to install either too much or too little grinding power. This paper explores this by comparing the actual performance of full scale regrind mills against their original design estimate. It confirms that serious scale-up errors have been made, and have then been perpetuated by ?benchmarking?. The test conditions to achieve accurate power estimation are discussed. The essential test conditions are: continuous (not batch) tests, ensure steady state (no coarse fraction retained in test mill), correctly account for classification, measure energy directly (not inferred), and using the same media size as the full scale installation. Failure to correctly address even one of these factors can bias results by 40%; failure to address several multiplies the error.

Jan 1, 2011

By Lathrop E. Roberts

[The opinion is general among smelter operators that magnetite formed in the converter and reverberatory furnace has much to do with the loss of copper in the slag. Its action appears to be due in part to its relatively high infusibility, chemical stability, and specific gravity, as a result of which it tends to fern a layer of highly viscous. "magnetite mush" between slag and matte. Particles of matte which might otherwise settle out of the slag are unable to pass through this layer. Maier and, Van Arsdale4 have shorn that the inclusion of prills of matte in the slag is also at times very probably due to chemical reaction between magnetite and the constituents of the matte. In smelter control and in envy laboratory study of slats the determination of magnetite is therefore a matter of some importance. The difficulties in the ray of making such a determination with any accuracy are rather obvious. Iron may occur in slog as ferric oxide, magnetite, various intermediate oxides, sulphides, silicates, as free metal, and in solid solution of several of these substances. Even of only the total iron content is to be determined, accuracy can be obtained only by painstaking and time-consuming separation ions from interfering elements. The determination of ferrous, ferric, and free iron in the presence of each other is a difficult matter under the most favorable conditions, and linen present in a slag the difficulties are increased by the refractory nature of the sample, by the presence of sulphides, and by ouch elements as vanadium and molybdenum.]

Jan 1, 1931

By C. J. Newman, R. J. St. Eloi, G. Macfarlane

"The Kidd Creek copper smelter has been expanded from its original design of59000 tonnes of copper per year to over 120 000 tonnes per year. Modifications to the process gas handling system and acid plant have been made to accommodate this higher production rate and, generally, to optimize the operation.The gas handling system associated with the continuous smelting process is discussed in terms of boiler accretions and modifications to minimize their impact on operations; design changes to effect reductions in high pressure drop duct configurations; material changes to overcome corrosion and plant additions to improve gas cleaning capability. The acid plant is reviewed with references to changes made to accommodate the increased S02 gas strength resulting from the higher smelting rates. IntroductionThe Kidd Creek Division of Falconbridge Limited is a base-metal mining and metallurgical complex located in Timmins, Ontario. The discovery of the original copper-zinc-silver orebody was announced in April 1964. Mining operations began in 1966 with a 9000 tonnes per day (t/d) concentrator corning on stream in November of that year. In April 1972, a 108 000 tonnes per year zinc plant was conunissioned. Over the years the facilities have been expanded, such that the concentrator now has the capacity to process 13 000 t/d of ore. To expand zinc production, the world's second installation of the Commco/Sherritt pressure leaching facility was completed in 1983 to bring total zinc production capacity to 136 000 tonnes per year. In 1973, serious planning for a smelter operation began. In early 1975, after studying both continuous smelting and flash smelting processes, a decision was made to proceed with the technology offered by Mitsubishi Metal Corporation of Japan. The Mitsubishi Continuous Smelting Process was to be used for the smelter and the Onahama No. 3 tankhouse technology for the copper refinery."

Jan 1, 1994