Search Documents

By Walter Nelson

Considerable thought and discussion had been devoted toward provision for increased milling capacity at the Allenby concentrator of The Granby Consolidated Mining, Smelting and Power Company operations as early as 1940. During the war, plans for the installation of an additional grindi.ng unit were formulated but were not carried out. It took considerable time after the war to prepare the mine again for its highest rate of production since, with the scarcity of men, development work had been sacrificed in favour of maximum ore shipments. In order to prepare for the expected competitive market in copper, the matter of increasing the capacity of the concentrator was again given serious attention. As ore became available in the mine and the output of the mill was increased, limitations for a satisfactory recovery were observed, due to the overloaded condition of the classifier units at the higher tonnages. From a metallurgical standpoint, the ore from the Copper Mountain mine had always been difficult to treat on account of the finely disseminated character of much of the mineralization and the difficulty of grinding to the desired fineness. This trouble has become aggravated with time as an increasing amount of wall-rock has diluted the ore and lower grade orebodies have been mined. It therefore has been, and is, the practice at the concentrator to maintain the maximum amount of reduction in size of material fed to the flotation units as is possible for the daily tonnage to be milled. This means that all the grinding units are operated for the maximum possible time, and that the classifiers are regulated to return as much feed ?as possible to the mills. The number of tons to be milled for ?the day is determined by the concentrator superintendent after ascertaining the availability of ore from the mine, the condition of the concentrator ore bins, and the need for repairs in the rolls plant. In order to maintain the tonnage des1red, hourly estimates are made of the rate of grinding by weighing the amount of ore contained on one foot of each of the belts conveying the feed to the various ball-mills, and adjustments are made accordingly.

Jan 1, 1950

By T. Badrujaman

In September 2005, after 30 years experiencing in operating an ESF using a falling water film shell cooling system, Antam entered the new era in operating an ESF, after completely modernized its ESF No. 2 from a falling water film shell cooling system to a copper cooling system. Further, in the beginning of 2007, Ferronickel plant No. 3, where its ESF also uses copper coolers, was successfully commissioned. By operating an ESF using a copper cooling technology, Antam has to face some challenges to establish the operation stability. Besides that, the chances to maximize the furnace efficiency are greatly opened. The shielded-arc mode of electrode tip is selected to operate an ESF under relatively high furnace power to produce metal having tap temperature below 1500? and slag having tap temperature below 1600?. It leads to electric current unbalance. Further, operating an ESF using a copper cooler system under high voltage as consequence of the furnace power raise increases metal and slag tap temperature. This condition damages furnace integrity fast. Besides that, relatively high metal temperature increases its pressure during metal tapping. It leads to failure in closing the metal tap hole. The main different ways in operating an ESF using a falling water film shell cooling system and a copper cooling system lie in the electrode tip mode, the water specification used for cooler, metal tap block maintenance and allowed metal & slag level in furnace. Since a copper cooler system allows an ESF to be operated by consuming nickel ore having ratio Fe / Ni up to eight and producing slag having relatively high Fe content in slag, an undesirable silicon reversion phenomenon becomes an obstacle in reaching the operation stability. A copper cooler technology lets Antam to take a chance to increase its capacity. Modernizing the ESF No.2 had increased its furnace power from 17 MWh to 25 MWh. Meanwhile the ESF No. 3 can be operated up to 42 MWh. This technology allows an ESF to be operated under relatively high furnace power above 25 MWh safely as well as prolong the campaign life of ESF brick. Further, lowering ESF power consumption, extending the limitation of ratio S/M in nickel ore consumed and adjusting Ni grade in ferronickel product can be gained by applying this technology.

Jan 1, 2014

By C. Dorfling, C. A. Snyders

South Africa has extensive mineral processing and extractive metallurgy capacity and infrastructure for metal production from natural resources. Decreasing ore grades, increasing labor costs, and more stringent legislation have made economic metal production from primary resources challenging. Opportunities exist for metal production from secondary resources such as mining wastes and end-of-life consumer goods. The objectives of this study were to evaluate the current status of metal production from secondary resources in South Africa and to identify potential opportunities for further development. Two main classes of secondary resources, namely mining waste and electronic waste, were considered. Primary metal producers are dominating metal production from mining wastes; several of the gold, platinum and chrome producers operate low risk and low cost tailings retreatment facilities that contribute significantly to their overall production. Further opportunities exist in, for example, the treatment of more than 450 estimated gold tailings dumps in Gauteng, as well as metal recovery from slags and furnace dust. The majority of companies involved with electronic waste recycling in South Africa focus on collecting and disassembling; only a few perform preliminary physical processing, with the recovered fractions then being sent overseas for metal recovery. Projections are that the rate of waste generation will increase significantly and that treatment will become critical to comply with more stringent environmental legislation. Projects related to process development, techno-economic evaluations and environmental impact studies for metal recovery from batteries, printed circuit boards, and fluorescent lamps are underway. South Africa is ideally positioned to further explore opportunities for synergistic relations between metal recyclers and primary metal producers. Processing of electronic waste for production of technology metals, for which limited natural resources exist in South Africa, would be a key enabler for local manufacturing industries and expansion of the value chain.

Jan 1, 2018

By I. Peerawattuk

Growing demand for Li-based battery technologies is leading to an unprecedented growth in the lithium industry. Although innovation in battery technologies has pushed lithium into the spotlight, lithium was not always known for its application in batteries. The primary use of lithium—prior to the introduction of commercial lithium-ion batteries in the early 2000s—was in the ceramics, glass, grease, and the medical industry. Before being converted into usable forms, lithium products must be upgraded from the raw material. Processes for recovering lithium may involve: thermal treatment, water leaching, solar evaporation, ion exchange, carbonation, and electrodialysis. Presented, is a historical review of lithium applications and the different techniques of converting lithium-rich minerals and brines into usable products with additional discussion on future lithium extraction processes.

By A. G. Roach

Introduction The plant described in this paper is located at Coniston, Ontario, the smelting centre of the former Mond Nickel Company. Coniston is situated some eight miles east of Sudbury on the main line of the Canadian Pacific railway and on the Toronto-Capreol branch of the Canadian National-railways. The plant is now under control of the International Nickel Company, as a result of the merger of the two companies in 1929. The smelter proper includes four 50-in. by 240-in. blast furnaces and five 13 ft. by 30 ft. converters, and has a capacity of about 65,000 tons of ore charge per month. As accessories to the smelter there are a mill, where some 10,000 tons per month of low-grade ores are concentrated, and the sintering plant, which is the subject of this paper. The present 6-unit sintering plant replaces a former 4-unit installation. Here, fine ores, concentrates, and flue-dust are sintered on Dwight-Lloyd machines, the sinter produced being charged into the blast furnaces. At the time of writing (1931), only the concentrator is operating at capacity, due to present world conditions.

Jan 1, 1932

By T. Moloane, C. Bergman, Heloise Thiele

"A pilot test campaign was undertaken to evaluate dense medium cyclone separation efficiencies on samples of iron ore fines (-1mm +300µm). Evaluations were done using both gas and water atomised FeSi types across a range of operating conditions in the presence of slimes build-up. A Mineral Liberation Analyser (MLA) was used to measure size, density, shape and liberation data of DMS feed and products. The results of the test work were used to obtain parameters for modelling of the partition size/density response. The findings indicated that accurate density characterisation of the feed ore is essential in understanding product quality and recovery, particularly due to the effect of porosity and micro-inclusions. A significant off-set between cyclone underflow density and separation cut-point (D50) was found indicating that relatively low feed media densities (about 3.4g/cm3) are required to achieve high density cutpoints of over 4.0g/cm3. In agreement with CFD modelling, the separation quality is dominated by viscous effects, hence FeSi type and slimes content will need to be carefully controlled to ensure efficient separation.INTRODUCTION In the South African context, future resources of hematite are expected to be both of lower head grade and will contain a higher content of banded iron formation (BIF) (1). These ores may require finer crushing in order to liberate the high-grade fractions and will thus increase the amount of -1mm material to be processed. In order to efficiently upgrade these materials, it becomes necessary to re-examine both traditional and novel processes to treat material finer than 1mm in size. These include spiral and up-current classifiers, wet high intensity magnetic separation processes, Reflux classification and potentially includes dense medium separation (DMS). This study presents a technical evaluation of fines DMS using a mineralogically-based particle tracking analysis method (PTA) to calculate efficiencies of separation."

Jan 1, 2018

By D. J. Hallbom

This paper presents a novel methodology for the hydraulic design of mine backfill distribution systems. The ?operating range? method uses the concepts of the hydraulic grade line and equivalent pipe length to determine flows and pressures as the pipeline route and static head change over the life of the mine. The operating range method is easy to learn because it is semi-graphical and uses well-known design concepts (e.g., the hydraulic grade line) and slurry design models (e.g., the Durand deposition velocity model). However, by changing the paradigm in which these concepts are used, the operating method allows all potential pipeline cases to be analysed simultaneously without the need to know the exact pipe routing. It also allows the hydraulics engineer to quickly identify ?pinch points? and ?slack flow? zones, to estimate the effect of changing the size or length of any given section of pipe, to assess the impact of changing the material properties of the backfill slurry, to size the slurry pumps, and to size and locate rupture discs when required.

May 1, 2007

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By John H. Johnson

This report covers the third and final year of work conducted under U. S. Bureau of Mines Grant G0166027, "Monitoring of Mine Air Pollutants". The report discusses work performed in three areas. These are the White Pine Mine (WPM) Experimental Unit, diesel mine-vehicle tailpipe emissions monitoring, and mine ambient air concentration data analysis. The WPM experimental unit was used to study diesel exhaust stratification in an 80 foot long dead-end heading while loading ore with a Wagner ST-5D scoop train LHD. The MTU Mine Air Monitoring Laboratory (MAML) was used to gather temperature and CO2 concentration data at 10 locations. Three different ventilation conditions were compared. The data substantiate the presence of strong buoyant forces of the hot exhaust gases which result in temperature stratification in dead-end headings. The diesel mine-vehicle tailpipe emissions monitoring study involved laboratory measurements of diesel undiluted exhaust pollutant concentrations by the portable tailpipe emissions measurement apparatus (EMA) assembled for in-mine use. The results were compared with simultaneous measurements by standard laboratory exhaust monitoring instruments. These results indicate that accurate field source quality control measurements can be obtained for CO2, CO and NO but NO2 results were low for all engine conditions. The mine ambient air concentration data analysis study included analysis of diesel pollutant concentration data in the Orchard Valley Mine air and comparison of the results with data collected earlier in the White Pine and Brushy Creek mines. The analysis included preparation of lognormal frequency distributions and calculations of C02-based concentration ratios and correlations. In the three mines compared, pollutant concentrations are distributed quite similarly, and the concentrations appear to be controlled to present standards.

Jan 1, 1979

By I. J. Hegyi, J. J. Tietjen, H. Nelson, J. I. Pankove

The fabrication of p-n junctions in GaAsl-,P, alloys by a vapor-phase gowth technique has for the first tirne resulted in room-temperature injection lasers capable of operating over a broad range of wavelengths extending into the visible region of the spectrum. The shortest wavelength achieved to date is 6750A at room tetnperature. In addition, at 78°K the threshold current density values for these lasers are generally the lo~vest reported, and the emitted radiation extends to the lozc,est wavelength ever attained (6350A). With lasers fabricated from material containing 14 pct Gap, quanticm efficiencies of 26 pct and peak power outputs of 25 zu were obtained at room temperature. ALTHOUGH room-temperature operation of GaAs injection lasers has been well-documented,&apos;-5 the operation of GaAsl-,P, (x > 0) laser diodes has been restricted to relatively low temperatures.8-&apos;0 This has been previously attributed5, 7, 10-12 partially to the difficulty of preparing single-crystalline GaAsl-& alloys having a high degree of chemical homogeneity and purity. Also, with these materials it has been difficult to prepare high-quality, abrupt p-12 junctions by diffusion techniques; and, in turn, this has made it difficult to obtain optimum electrical properties for room-temperature operationL3 in the resulting laser diodes. As a result, GaAsl-,P, laser diodes have not been efficient enough to permit operation at room temperature. For example, using diffused structures, only a few diodes were obtained which could be operated even close to room temperature (255K)." Recently, a vapor-phase growth method of preparing epitaxial deposits of GaAsl - .P, alloys has been described,14 and the high-purity and homogeneity of these materials has been previously demonstrated. Of special significance, with this technique, n- or p -type doping can be initiated or discontinued at any time and at almost any rate during the crystal growth so that the donor and the acceptor concentrations can be easily controlled to obtain desired impurity profiles. This permits high-quality, abrupt p-TZ junctions to be vapor-phase grown entirely during the crystal growth process, so that diffusion or other p-n junction fabrication processes are unnecessary. After growth, the device does not have to be heated to elevated temperatures, which avoids the possible unwanted introduction and motion of both impurities and lattice defects. Using the vapor-phase growth method cited above, over 300 room-temperature injection lasers have been prepared from GaAsl-,P, alloys having compositions in the range of 0 5 x 5 0.41. These lasers have emitted cohe~ent radiation in the spectral range of 8350 to 6350A at 78°K or from 9000 to 6750A at room temperature. The threshold current densities of the best lasers are independent of the alloy composition over the range 0 < x < 0.2 and compare favorably with values for good GaAs lasers.&apos; MATERIAL PREPARATION Multilayer, epitaxial deposits of GaAsl-,P, alloys are prepared by a vapor-growth technique described elsewhere.14 With this technique, the individual layers which comprise the multilayer structure are prepared sequentially in the deposition apparatus without interrupting the crystal growth. The epitaxial layers are deposited on GaAs substrate surfaces oriented normal to the ( 100) direction. The substrate wafers employed in this study were usually doped with tellurium to an electron concentration of approximately 2 x 10" per cu cm. To avoid strains, the first 10 to 15 p of the deposited material is uniformly graded from pure GaAs to the specific GaAsl- ,P, alloy composition of interest. The GaAsl - ,P, alloy growth is then continued to form a layer of constant composition having a thickness in the range of 25 to 75 p. Both the graded region and the layer of constant composition are doped with selenium to an electron concentration of about 2 x 10" per cu cm. The p region of the diode is then incorporated in the crystal by abruptly changing the dopant concentrations in the vapor phase to facilitate doping with zinc. This layer has a hole concentration of approximately 3 X 1019 per cu cm and typically is 50 p thick. DEVICE FABRICATION In general, the GaAs substrate and the region of graded composition are removed. Ohmic contacts are made to the n-type side by tin evaporation and to the p-type side by an electrodeless nickel deposition. This is followed by an electrodeless deposition of gold on both sides. The crystal wafer is then cleaved along (110) planes and sawed into rectangular parallelepipeds. Typical dimensions are 100 by 300 for the junction area and 100 µ for the diode height. The diodes are either soldered to a copper stud or pressure-mounted in a copper clip. RESULTS AND DISCUSSION Approximately 400 laser diodes having compositions in the range of 0.41 have been prepared by the method described above. Each laser was routinely tested at liquid-nitrogen temperature. The lasers were operated with l-psec current pulses at a repetition rate of 60 pulses per sec. The parameters of greatest practical interest are the photon energy or wavelength of the laser output and the threshold current density. Fig. 1 shows the variation of photon energy with alloy composition at 78°K. The composition was determined from the lattice constant of the material obtained by X-ray back-reflection measurements. Although there

Jan 1, 1968

By Ronald B. Stotelmeyer

This report summarizes studies of 55 Idaho national forest roadless areas completed by the U.S. Bureau of Mines (USBM) in the period 1966-1992. These roadless areas have been recommended for addition to the National Wilderness Preservation System, proposed as special management areas, or otherwise recommended for study by the U.S. Forest Service or the Idaho congressional delegation. The Bureau of Mines&apos; studies indicate which parts of the roadless areas contain mineral resources. They also show where mining and prospecting are likely to occur in the future, where mineral production has occurred in the past, and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character.

Jan 1, 1994

By D. S. Scovira, T. Gustavsson

Exiting WW2 (mid-1940s), the potential of nitrates (ammonium nitrate, calcium nitrate, sodium nitrate) and hydrogen peroxide for application as a commercial explosives for mining, construction, and other industrial purposes both became known. The technology stream advanced the development and uptake of nitrate based explosives to the point that they are the current global standard for blasting. Today, environmental issues are shaping the strategic agenda across various industries. Most global mineral resource, construction houses, and explosive manufacturers have publicly announced ESG carbon reduction commitments in support of COP26 Net Zero 2050. The mid-2010s saw a renewed interest in hydrogen peroxide explosives to eliminate NOx fume. Carbon reduction initiatives in the early 2020s provided additional impetus to investigate hydrogen peroxide based explosives for industrial use. Hypex Bio has recently pioneered the formulation, manufacture, and end-use delivery of a Hydrogen Peroxide Emulsion (HPE) on an industrial scale. The HPE is composed primarily of hydrogen peroxide (H2O2) plus a lesser amount of fuel and emulsifier phase. The base HPE is produced in a low energy intensity modular plant using industry proven mixing techniques. The base HPE is a white, highly viscous emulsion that is similar in consistency to base nitrate emulsions. To enable end blasting use, a mobile charging unit gases the base HPE to a detonable density. The HPE is compatible with current priming and initiation systems. Hydrogen peroxide explosives offer a significant reduction in total carbon emission as compared to nitrate based explosives. The production of ammonium nitrate (AN) emulsion is energy-intensive and not carbon neutral. Based on the EU Average and for the oxidizer phase only, 1 kg [2.2 lb] of AN emulsion emits 2.3 kg [5.1 lb] of CO2 as compared to the production of hydrogen peroxide emulsion that results in 0.23 kg [0.5 lb] of CO2. This is a difference of 90%. HPE contains no nitrates and does not generate post blast nitrous oxides (NOx). HPE generates no aqueous nitrate or ammonia pollution and is a solution to meeting increasingly regulated mine site water discharge limits. Hypex Bio recently conducted a successful underground HPE evaluation with a major mining company in Sweden. HPE blast designs were the same as those done with nitrate based emulsions. Rock breakage, advance, muck displacement, and excavator performance were equivalent. Ventilation and re-entry times were reduced. The mining company has expressed further interest in assessing HPE and is demonstrating industrial leadership by exploring this transformative explosive technology

Jan 1, 2024

By P. R. Tisot

Knowledge acquired from this research contributes to a better understanding of the physical structure of Green River oil shale and provides fundamental data and concepts that may serve to improve oil-shale technology. This study by the Bureau of Mines indicates that oil shale is a highly consolidated organic-inorganic system with no significant micropore structure, pore volume, or internal surface. This system is a form of physical structure that precludes rapid diffusion of either gases or liquids. The mineral matter consists essentially of nonspherical particles that tend to follow a log-normal size distribution. An excess of 99 weight-percent of these particles have equivalent spherical diameters of less than 44 microns--75 weight-percent are from 2 to 20 microns, and 15 weight-percent are less than 2 microns. The surface area (3 to 5 square meters per gram) of these mineral constituents is mainly external surface. The mineral constituents contain some micropore structure--pore radii ranging from 10 to 100 Angstrom--with the pore sizes randomly distributed. Distribution of the organic matter within the inorganic matrix is essentially interparticle and not intraparticle. The organic matter within the micropores of the mineral constituents is less than 4 percent of the total. Estimates made from surface area data suggest that perhaps only a small amount of the organic matter is bonded either physically or chemically to the mineral constituents.

Jan 1, 1963

By Glen C. Ware

The Bureau of Mines determined the factors involved in the corrosion of starting sheets used in the production of electrolytic zinc with the ultimate purpose of adapting zinc starting sheets to commercial practice . Under present practice , zinc is electrodeposited on aluminum cathodes and subsequently stripped for melting . The use of zinc instead of aluminum would eliminate the need to strip the deposit , thereby reducing the cost of handling and melting it , but zinc has not been suitable because it was too vulnerable to the corrosive attack of the electrolyte . Serious attack was found to be limited to the areas of the cathodes situated immediately above the surface of the electrolyte and to re - entrant corners . It was possible to avoid solution - level corrosion by immersing the starting sheets completely , exposing only a relatively heavy suspension member to solution - level attack . Zinc starting sheets could be made as reliable as aluminum and could be continued in residence for periods up to 39 days . Periods as long as a week were feasible under conditions similar to those found in commercial practice . A test of zirconium as a starting - sheet material showed that it promoted corrosion of the deposit to a lesser extent than aluminum and that the deposit adhered less tenaciously . These two properties lend themselves to the development of ways to strip deposits mechanically from zirconium starting sheets . Titanium was unsuitable for use as a starting - sheet material .

Jan 1, 1963

By W. G. Davenport

Chapter 1 showed that flash smelting is a key step in extracting copper from sulfide ores. It also showed that there , are two versions of flash smelting: (a) Outokumpu flash smelting, which uses oxygen-enriched air blast and injects dry feed downwards into a hot furnace (b) lncoflash? smelting, which uses industrial oxygen blast and injects dry feed horizontally into a hot furnace. This chapter describes Outokumpu flash smelting.

Jan 1, 2001

By Florian Kongoli

The behavior of cobalt as a by-product in the NilCu smelting and converting processes effects directly the quality of the final products as well as the revenues gained from the overall process. An effective way to evaluate and predict this important behavior is thermodynamic modeling which reduces the time and the cost of experimental investigation. In this work a thermodynamic model of cobalt-containing matte phase in NilCu smelting and converting processes is presented. The model predicts a priori the thermodynamic properties and phase relations of the ternary and multicomponent matte based solely upon the optimized parameters of the binary systems. This model can be used with other models such as those of slag, metal, gas etc. to predict various aspects of cobalt behavior such as matte- slag, metal-slag distribution, etc.

Jan 1, 1999

By D. A. Bruce

To check the feasibility and the quality of a very deep diaphragm wall, a tern of adjacent panels has been constructed, up to a depth of 100 m, in the Milan sandy gravelly soil by means of a hydraulically driven milling machine with reverse circulation of mud. The results of the monitoring carried out in order to evaluate the panel geometry and the quality of both joints and concrete are described. The use of instrumentation based on different physical principles allowed the cross checking of measurements as well as the evaluation of the accuracy and sensitivity of each single procedure to be performed. The trial field was successfully carried out and the feasibility of a diaphragm wall of such a depth was demonstrated and corroborated by a reasonable level of quality control.

Jan 1, 1989

By P Ridley

EnergyAustralia’s Sydney Central Business District (CBD) cable tunnel network will form a loop 6.2 km in length. The 3.2 km long, 3.5 m, diameter city east cable tunnel (CECT) currently in design, will complete the loop in 2014. This paper discusses the ventilation design of the CECT, considering operation for four functions:1. normal (unmanned),2. access (manned),3. purge, and4. emergency fire modes.The dominant design criterion which determines the required ventilation capacity for CECT is the specification of an upper air temperature limits of 35°C (dry bulb) and 24°C (wet bulb) for manned access, during all ambient weather conditions and cable heating loads. Simplistic static heat transfer analyses do not yield a sufficiently accurate calculation of tunnel air temperature and humidity to provide a safe and yet economical design. The primary refinement in the analysis discussed in this paper is associated with modelling of the system’s dynamic behaviour.Our means of analysis is through a thermo-fluid-dynamic simulation of the interactions between the diurnally and seasonally varying loads (cable heat generation, ambient air conditions and groundwater inflow), tunnel airflow and the resulting tunnel air temperature and humidity. These simulations are validated using experimental data from the existing city south and city west cable tunnels.Fire life safety scenarios are also analysed and discussed in association with the ventilation design. Ventilation strategies are developed for dealing with such emergency fire situations.The understanding and insight provided by the work offers the ability to optimise ventilation plant provisions in future cable tunnels, particularly long and high energy density tunnels.

Mar 8, 2011

By A. Wahab Khair

Coal mining has evolved into extensive use of continuous mining machines for development and production. This has resulted in an increase in dependence on the versatile continuous miners. The present-day continuous miners are powerful in terms of rated power but are still plagued by wear of bits which hinders development and production as the bits have to be continuously changed at regular intervals. Previous attempts to analyze bit wear has been either restricted to the theoretical approach and or laboratory testing. This paper discusses about the overall aspect of bit and drum design for different conditions. Using the laboratory model set up, numerical models and field testing, a new bit and drum design was analyzed to evaluate their performance under different conditions. The results proved that a newer bit design and drum design were successful in limiting the amount of wear as well as improving the performance of the continuous miner and production.

Jan 1, 2008

By R. Blickensderfer

The laboratory wear testing capabilities of the Bureau of Mines are described, Wear tests are used to support the Bureau?s research efforts toward reducing the wear of equipment used for mining and minerals processing and any wear involving a loss of strategic or critical materials. The emphasis is on abrasive wear because it accounts for most of the wear losses that occur in mining and minerals processing equipment, Spalling wear, caused by repetitive impact in grinding equipment, also is included, Ten abrasive wear tests, including high- stress and low-stress and two-body and three-body conditions, are described: dry-sand, rubber-wheel abrasive wear; Taber Abraser; abrasion resistance of refractory materials; dry-particle erosive wear; elevated-temperature, dry-particle erosive wear; low-angle slurry pot; jaw crusher gouging wear; ball mill wear; pin-on-drum abrasive wear; and high-speed impact gouging. Two repetitive impact tests are described: ball-on-block impact-spalling and ball-on-ball impact-spalling. Test equipment, procedures, and specimens are described, and typical test results are presented and discussed.

Jan 1, 1985