Search Documents

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By Eder Salazar

El presente texto describe la optimización de la productividad en la empresa minera a través de la mejora contínua en la cadena de valor en SMEBSAA, los siete pasos de la calidad, proceso de mina, planta, soporte y la cuantiificación de dicha mejora en la cadena de valor en SMEBSAA. Asimismo, la implementación de los diversos sistemas de gestión refuerzan los resultados, siendo el Sistema de costeo basado en actividades el gran agrupador de toda la información de los módulos: Logístico, Control Patrimonial, Orden de Servicio, Planillas y Contabilidad.

Sep 12, 2005

By David S. Bowling

The ER-300 Series White Recorders were developed to provide on economical, yet invaluable instrument for those who desire permanent recordings of such data OS displacement, vibration, concussion (air borne effect) and velocity information. The precise monitoring of earth displacements and air blast magnitudes aids quarrymen and construction contractors in estimating safe blasting limits when operating in populated areas. A refraction model is available for recording velocities which permit the determination of weathered zone depths as well as the .depths to other subsurface formations. The dual purpose (Refroction- Displacement) systems ore utilized for velocity studies and displacement - oir blast measurements.

Jan 1, 1990

By CLARENCE G. SMITH

Prior to the actual development of an oil property it is difficult to determine the quantity of oil under the property and the rate at which this oil can be brought to the surface-factors that determine the ultimate value of the property. Consequently, there has been much confusion in devising accounting systems that, during the entire life of a property, will show costs and profits from which the producer can determine whether his property is being worked at a profit or otherwise. The Bureau of Mines publishes this report in recognition of a distinct need for a simple treatise on accounting methods adapted to the peculiarities of the petroleum industry. Probably many companies operating oil wells are not fully acquainted with details important to the welfare of their business, because their account books fail to furnish them with exact and adequate data. With the accountant rests the responsibility of providing the management with reports setting forth the details of the business expressed in fitting terms as well as in dollars and cents. These reports are a means whereby efficiency may be maintained, waste prevented, oil obtained and sold, and money suitably reinvested. They also enable a concern to study the progress of its business in order to conserve to the utmost the possible benefits from an exhaustible deposit of mineral wealth. When managements realize the extent of the waste at their properties more attention will be given to the character of the accountancy records. Herein are presented descriptions and discussions of balance sheets, profit-and-loss statements, and bookkeeping methods peculiarly adapted to the oil business. As far as possible, technical phrases have been omitted in order that those not familiar with accounting terms may be able to follow the subject matter. The systems of keeping books outlined in Chapter X have all been found practical. For brevity as well as clearness the major part of the work refers to the company operating only one property.

Jan 1, 1917

Mr. Chairman, distinguished guests, ladies and gentlemen. Thank you for asking me to your conference, with its most fundamental and appropriate topic of 'Investment in Mining'. I must confess at the outset that I am one of those Australians who has rarely visited your fair land of New Zealand. This is in fact only my third visit, with all three related to Institute Conferences, and all much too brief. In so many ways your country provides a counterpoise to ours, despite the obvious disparities in size and population. And I am not only referring to the Bledisloe Cup! We would certainly each be much more lonely without the other, in this strange long-lost corner of the globe û if globes can have corners. Such an important factor in common in our shared heritages has been the mineral industry we have won from our alluvials and our rocks û especially for gold. So much of the major mineral developments which have supplied the world's appetite for metals and fuels in the past two hundred years has come from the countries settled in that period by people from Europe, especially those from the British Isles. So much of the technology for mineral and metal extraction has come from the skills of those people in New Zealand and Australia. And so much of the further development of metal processing and manufacturing of productive equipment has come from those people and from their cousins throughout the world. It is, I believe, a fair question to ask why we have failed to build on those early and considerable successes, and why we have in so many ways apparently been so content to allow others to add value to our raw materials, and to take our technological developments on to levels far beyond those that our domestic markets could sustain.

Jan 1, 1988

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By Ari Jokilaakso, Junjie Shi, Zhuo Chen, Pekka Taskinen, Xiang Gao

The amount of copper flash smelting slag has increased during the recent years along with an increasing slag-to-metal ratio. During slag tapping, some copper sulfide is mechanically entrained. As a result, it is necessary to recover copper matte from the slag by suitable methods. At present, the most common way is slow, controlled cooling in a transfer ladle. However, research on the detailed effects of slow cooling and the function of slag modification is rare. This paper described experiments that were performed at different cooling rates (0.5, 1.5, 3, and 7 °C/min), with and without additive. A detailed characterization of the copper-rich phase and its particle size was subsequentlymade using SEM-EDSmicrographs and image analysis software.With a decrease in cooling rate, the particle size of the copper-rich matte phase became larger. The addition of gypsum and carbon as a slag modifier affected the size of the copper-rich phase slightly, and its chemical composition was modified compared with the experiments without additive.

Jul 31, 2020

By Jean-Michel Rendu

Computer systems are an integral part of the mining industry. Before a new operation is started, software requirements, and the need for hardware and communications must be determined. The personnel required to use the software, and to support the necessary infrastructure, must be hired and trained. In this sense, this paper emphasized the needs that geologists and mining engineers have for technical software. Similar requirements apply to all other aspects of a mining operation. These requirements will become even more critical in the years to come, and must be fully assessed before construction of a new mine begins. Dependency of a mine operation on its computer systems must never be underestimated.

Jul 17, 2000

By J. R. Thoenen

In June 1929 the Bureau of Mines issued a 13-page information circular entitled "Mineral Wool," which was one of the first publications to present to the public Rome technical aspects of the mineral-wool industry. Since then several articles on the subject have appeared in the technical press as well as in publications of State organizations. Inquiries for information on mineral wool have continued to be received by the Bureau of Mines in large number, and in 1935 it was decided to make a field survey of the plants then producing and to collect therefrom technical data to be compiled in a paper for nubile distribution. With the cooperation of the industry, this survey was made, and Information Circular 6984, Mineral Wool, was published in January 1930. The issue was exhausted after a few months, and requests for copies continued to come to the Bureau. As opportunity arose, further field studies were made in American as well as Canadian plants. The present circular contains the essential information in Information Circular 6994 together with date from later field studies.

Jan 1, 1939

To provide a flexible, low-maintenance, low-cost continuous mine air monitoring system as an alternative to conventional fixed-point, electronic monitoring systems. Background Continuous monitoring of mine air is highly desirable (and often required) not only to improve miner safety, but also to increase mine productivity. Continuous air monitoring systems can provide earl" warning of developing fires, excessive methane accumulation, reduced oxygen levels, and other developing problems in remote, inaccessible or sealed areas, and in active workings. Fixed-point, electronic systems require one Sensor for every gas to be measured at every defined monitoring location. As the number of monitoring locations increases, so does the cost, along with increases in the time required for routine maintenance and calibration of the sensor System cost also increases when monitoring locations are identified for mine areas requiring permissible electrical equipment.

Jan 1, 1988

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

By AIME AIME

THE climax of the various programs and entertainments in connection with the holding of the World Engineering Congress* in Tokyo in October was the complimentary dinner given by the visiting members of the Institute to our members in Japan. At the same time President Bradley conferred an honorary membership on Baron Takuma Dan, the vice-president of the World Engineering Congress.

Jan 1, 1930

By H. Hearnden

Whereas in the past, ladles were simply a means of transferring molten products from furnace tapholes to points of discharge be they casting pans or waste dumps, the ladle is now becoming a more integral and versatile piece of equipment in the pyrometallurgical plant. The drive behind this development is the need for continuous improvement in performance where better, faster and cheaper means remaining competitive in the global market. This paper will explore the technologies available for the rendering of a costly and otherwise cumbersome piece of pyrometallurgical equipment more efficient and versatile in adding value to the final product. Essentially it all revolves around heat and more importantly the loss of it when tapping. The common practice is to move the molten product to its point of discharge quickly with the minimum of interruption to prevent skulling and hence the cost associated with clearing it. The advances in Oxy-fuel burners, AC or DC ladle furnaces, converters, gas purging and high velocity, bath injection systems has increased the versatility of processes and enhanced the potential for adding value to intermediate products through down stream practices such as granulation and atomisation.

Jan 1, 2004

By John P. Wagner

The details of a three-phase study (total time period of 12 months) entitled ?Fire Alert Systems for Metal and Non-Metal Mines,? are presented. Phase 1 consists of a state of the art survey on fire detection devices and gas sensing techniques. Phases 2 and 3 include laboratory screening and systems concepts testing on various detectors classified as products of combustion, optical view-field and contact (or thermal) types under incipient and flaming combustion conditions. Recommendations for a mine fire detection system to protect shaft, sealed off or mined out (from spontaneous combustion of sulfide containing ores and cellulosic materials), and fuel storage areas are also included. me principal problem area noted during Phase 1 study is the high expected occurrence of false alarming of products of combustion detectors (POC") subjected to normal mining operations---diesel vehicles and equipment and shot firing or blasting operations. Simultaneous gas sensing of either the ratio of CO/NOx or CO2/NOx with detection of one or more fire signatures (smoke, radiant energy, or heat sensing) is the recommended approach to discriminate against these operations.

Jan 1, 1975

By Agne Rustan

The goal of this paper is to describe Fragblast 10 for those who did not have the opportunity to attend the Symposium and also give some examples of new research findings used in practise in some countries throughout the world. Also some entertainment events from the symposium are described.

Jan 1, 2013

By Orica

Unlicking the Possibilities ISEE Digital Detonator Workshop New Orleans, LA Wednesday, February 4, 2004

Jan 1, 2004

By B. Arjang

ABSTRACT: Ground stresses are one of the significant factors in the context of rockbursts and underground instability at some hard rock mines in Canada. Overcoring strain relief measurements using triaxiaI strain eel is were performed at depths between 60 to 1890 m at several mine sites to provide stress data for stability analysis and optimum mine design. Pre-mining ground stress determinations from 64 stress tensor analyses resulted in the following average stress gradients: Maximum horizontal stress. -Hmax - 8.18 - 0.0122 MPa/m depth Minimum horizontal stress. _-,,min - 3.64 - 0.0276 MPa/m depth Average horizontal stress. -11, 5.91 - 0.03-19 MPs m depth Vertical stress. '-, - 0.0266 - 0.008 MPa/m depth The maximum and minimum horizontal compressive stresses. with an average ratio of 1.75 ,0..45. prevail in east--west and northerly directions. respectively. Horizontal compressive stresses in excess of vertical overburden load were determined. indicating large variations in ratios to a depth of about 1000 m with decreasing trend towards depth. From present data. a particular regional zoning for the magnitude and direction of horizontal stress fields cannot be outlined. A common feature at mines with near vertical orebodies is that the maximum horizontal compressive stress acts perpendicular to strike while the minimum horizontal compressive stress is aligned on-strike. The vertical stress components approach the gravitational overburden load.

Jan 1, 1989

By Chas. F. Jackson

During the past year a special study was made of shrinkage stoping A large number of mines in the United States and Canada which employ this method were visited and their practices were discussed with the operating staffs. The operating data obtained are appended hereto. Data were also abstracted from the literature on other mines and are combined in tables with data personally secured by the author. References are made to these published articles, some of which have appeared as information circulars of the United States Bureau of Mines, in the Transactions of the American Institute of Mining and Metallurgical Engineers, and the Engineering and Mining Journal. Several of the mines referred to which have not been described in individual papers will be described in detail in information circulars to be issued by the bureau. Eventually it is planned to combine and condense the information in these circulars and present the data in bulletin form.

Jan 1, 1930

By M. Hopf, E. Rossouw

Keywords: Pyrometallurgy, furnace, copper coolers, freeze lining, monitoring, Saveway The use of water-cooled copper components as sidewall elements of submerged arc furnaces and other pyrometallurgical applications has become increasingly common. The high cooling efficiency of copper has made it possible to increase the service life of furnace refractories when compared to conventional refractory linings. However even the self-healing effect of ?freezing? worn areas of the lining does not necessarily protect the copper coolers against wear or corrosion completely. In order to avoid furnace explosions, various methods have been used to monitor the wear of coolers. Unfortunately, these have not been able to consistently identify localized wear. Thos Begbie (South African) and SAVEWAY (German) jointly developed technology to embed a line sensor into the copper cooler during the casting process. This system allows an exhaustive monitoring of the copper cooler. A SAVELINE sensor is placed inside the copper-cooling panel between the water-cooling passage and the hot face of the panel. The sensor follows the meandering shape of the cooling water channels. In the first instance, the sensor provides analogue information as the thickness of the copper reduces. Secondly, this wear signal will be confirmed by a signal of interruption if the sensor is washed away. Because of the structure of the sensor, a self-diagnosis is possible and indications can be confirmed (double proofed). Subsequent to the manufacture of some test pieces, coolers for a large submerged arc furnace were manufactured. The sensorized coolers have been installed at the intermittent surface (slag line) where the largest amount of corrosion has been encountered. The system has been operating since December 2005 in what is considered one of the largest submerged arc furnaces in South Africa.

Jan 1, 2006

By Lumley G, Rowlands D

The overburden slusher (OS) is proposed as a stripping tool that is expected to find application in overburden stripping operations including open cut coal and oil shale mines. OS is expected to combat the effects of increasing depth on the productivity of conventional dragline stripping.Although previously developed stripping techniques have included the use of drag scrapers the OS is sufficiently different as to constitute a new stripping method.A study undertaken at the University of Queensland during 1985 is believed to be the first major study on the use of the OS and preliminary economic results are very encouraging. It appears that the OS has the capacity to remove overburden at a cheaper unit cost than the equivalent powered dragline stripping machine at any comparable depth of overburden. The OS is not adversely affected by increasing stripping depth to the same extent as a dragline. In addition, the action of the OS machine allows for the lowering of spoil face angles, thereby reducing spoil slope stability problems encountered in deep open cut strip mines.

Jan 1, 1986