Search Documents

By J. B. Rosenbaum

Prolonged laboratory and limited pilot plant tests have shown that the Bureau of Mines buffered S02 -H2S process is capable of removing 95 to 99 percent of the S02 from industrial waste gases. Most of the S02 is converted to elemental sulfur; only about I percent converted to sulfate The process comprises (1) washing the flue gas to remove particulates and S03, (2) absorption of the S02 in citric acid or other carboxylate solution, (3) reaction of the loaded solution with H2S in a closed vessel to precipitate the absorbed S02 as elemental sulfur, and (4) separation of the sulfur from the regenerated solution by oil flotation and melting. Two-thirds of the molten sulfur is converted to H2S for use in the sulfur precipitation step by reacting sulfur vapor with natural gas and steam in the presence of an alumina catalyst. The chemistry and mechanism of the process are described, initial laboratory and pilot plant data are summarized, and second-generation laboratory operation and pilot plant design are reviewed. Preliminary cost estimates are presented for recovering sulfur from copper smelter gas, powerplant flue gas, and Claus plant tail gas.

Jan 1, 1973

By C. H. Titus

This study consists of four descriptive Sections covering respectively: a state-of-the-art literature survey on ungrounded and grounded power systems, a report on literature pertaining to human threshold limits of electric shock, an analysis of the performance requirements of isolated systems and a section on design and performance specifications for an isolated system the final section includes copies, and translations where applicable, of the most important articles on foreign mining practice as well as some technical publications which could be difficult to obtain elsewhere. Section 2 - Literature Survey In analyzing the available literature on ungrounded systems it became apparent that too strict an interpretation of Section 1.1 of the Contract would limit the survey in both period of time analyzed and in available literature which discussed several types of power systems. Therefore, the survey was expanded to cover approximately the past twenty-year period and to cover literature which addressed itself to both ungrounded and grounded power system operation. Section 2 gives a brief summary of this literature survey and lists the important papers and books which were examined.

Jan 1, 1972

By Eugene H. Skinner

This Bureau of Mines report describes the fieldwork and subsequent analysis to determine physical properties, stress distribution, and several aspects of rock behavior as a necessary evaluation for a typical mine opening. All work was done at a test site on the 3300 level, Crescent mine, Coeur d'Alene mining district, Idaho. Free field stress beyond the influence of the opening was also determined. Conventional overcore technique with the three-component borehole deformation gage developed by the Bureau of Mines was used in three drill holes. Three field verification tests were performed using a gage newly developed by the Spokane Mining Research Center in an approach herein termed "initial deformation method." Use of this method validated that aspect of overcore theory which predicts that similar deformation effect occurs in the wall rock around the perimeter of an opening in rock under stress. Also described are all drilling procedures and performances. Physical property determinations were made on rock samples obtained from the three overcore drill holes. Twelve physical properties with a total of [532] values were obtained at various drill hole orientations and depths. Exhaustive statistical tests were utilized in the analysis of these physical properties. Further elaborated are statistical inferences based on these analyses. Extensive analysis and interpretation of Crescent mine geology are also described.

Jan 1, 1974

By James K. Richardson

Today, the enigma of the "missing man" in the metal mining industry equals, and frequently surpasses in objective importance, the problems of ore development, drilling, sampling, pumping, milling techniques, geophysical prospecting, or any one of a hundred highly technical subjects. Unfortunately, as engineers, we have confined our attentions, in the main, to the scientific phases of mineral technology, relegating our man power problems to the background. But what good has all our scientific study and preparation been if we can't get the ore mined, milled, or smelted? What has happened to our labor supply? Where is the good old miner who could timber, drill a round, lay track, or do any job underground?

Jan 1, 1949

By E. J. (Kirk) Conway

The objectives of this project were to: (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess its impact on productivity and personnel safety, and (3) develop maintainability guidelines to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. The purpose was to identify design approaches and features that enhanced and degraded the maintenance process. Mine management, safety, and maintenance personnel were also interviewed to identify machine specific design problems. Six original equipment manufacturers were visited and the procedures used to enhance the maintainability of Their equipment discussed. Volume I of the Final Technical Report presents an overview of procedures and protocol used and a summary of the findings. Volume II includes the maintainability design guide for mobile underground mining equipment.

Jan 1, 1988

This Department handles all ores prior to blast-furnacing, the object of the operations being to mix the lead-bearing material with fiuxes, eliminate sulphur from the mixture, and produce a homogeneous sintered product which is chemically and physically suitable for treatment in the blast furnaces.During the financial year ended the 30th June, 1937, the tonnage of charge treated was 458,960 tons, containing some 183,470 tons of lead and 8,504,000 oz. of silver.The quantities of the principal components of the charge treated were as follow:-

Jan 1, 1937

By Stanley C. Rhoads

The Bureau of Mines investigated the complete ternary system K2 HfF6¬K2ZrF6-l.25 weight-percent HF at 40° C. In addition, solubility curves have been established at 25°, 30°, 500, 60°, and 70° C. These solubility data implemented a study of hafnium enrichment in feed solutions for liquid-liquid extraction processes.. Selected K2HfF6-K2 ZrF6-1.25 weight-percent HF mixtures were equilibrated in a constant temperature bath. Compositions of the equilibrated solutions and wet residues were established from combined hafnium and zirconium oxide and total fluorine analyses. All solubility curves were essentially parallel on triangular coordinates. At 40° C, the solid phase of the K2HfF6-K2ZrF6-1.25 percent HF system is a series of solid solution hydrates with K2HfF6-H20 and K2ZrF6.3H2O segments existing at the respective extremes. Since this system contains K2HfF6-H20 and K2ZrF6.3H20 segments, it is not ideal for simple separation of high-purity K2HfF6 from K2HfF6-K2ZrF6 mixtures by recrystallization. However, it would be useful for producing hafnium-enriched feed solutions from zircon concentrates for liquid-liquid extraction of hafnium from zirconium.

Jan 1, 1973

By W. G. Huang

To recover the coal resources of high-sulphur anthracite in Jincheng Mining Area, underground coal gasification (UCG) of No. 15 seam in Fenghuangshan Coal Mine was proposed. The feasibility of the project was confirmed by investigations of occurrence conditions, coal properties, and roof conditions, as well as experimental studies and theoretical analysis. It was found that UCG technology is appropriate to be adopted in the mining of the No. 15 seam, due to the stable rock conditions, simple geological structure and hydrogeology, the high carbon content of the coal, non-cohesiveness, medium-thermal stability, high ash fusion temperature, and weak reactivity with CO2. Further factors are the characteristics of the immediate roof, which consists of 9.11 m of limestone and mudstone with a compact structure and low permeability, and 4.27 m of dominantly mudstone with low permeability.

Jan 1, 2012

By Bruce E. Stauffer

The report recommends criteria for the design of safe surface mine haulage roads. Information relevant to road design at surface mine sites delineates vertical and horizontal alignment; subbase and surface materials; drainage; cross-slope, superelevation; runaway vehicle protection; and road and vehicle maintenance criteria. An appendix Is included which details the study methods used in compiling the final report information. A bibliography following the main text lists literature referenced for the report data and which is available as a valuable tool for use by individuals involved in haul road design.

Jan 1, 1976

By A R. Sale

This paper highlights two aspects of the mineral sands industry in Australia: the development of the industry from approximately 1870 through to 1980, and the author’s experience in the industry from 1966 to date.The first real heavy mineral (HM) mining in Australia started in 1870 with the mining of heavy mineral slicks on the beaches along the east coast of Australia. The real potential of Australian heavy minerals was however only realised in the 1920s with the first production of a heavy mineral concentrate that was shipped to Canada for processing. Post WW 11 and the Korean War, Australia was the largest producer of mineral sands products in the world as well as a significant developer of associated separation equipment and technology. The number of producing companies in the east coast peaked at 33 in 1957, was reduced to ten by 1965, and subsequently further reduced to five in 1980 as a result of potential mining areas being declared National Parks or Conservation Reserves. Today there is one company, Unimin Australia Pty Ltd (formally Consolidated Rutile Ltd) operating on the east coast. In contrast there were three companies on the west coast in 1965, four companies in 1980, and four companies today (albeit not the same companies).There have been considerable ups and downs for the industry in Australia, however world wide it was renowned in the past as being an industry that attracted numerous interesting and innovative characters that played a major role in developing it into the vibrant industry that it is today. This, given the current climate, is predicted to continue into the future.The author has been continuously involved in the industry for over 45 years from 1966, initially as an electrician at Consolidated Rutile Ltd culminating in the role of General Manager/President of Iluka Resources Limited USA, prior to his retirement in 2009. His exposure has been world wide and has covered all aspects of the industry but in the main focused on project development and operational areas. During this time there have been significant technological advances, yet to some extent the basic principles have not changed at all. Some of the most noteworthy advances include the development of the Wright Spiral in 1977, the development of the Reading High Intensity Wet Magnet (WHIMS), the rare earth magnets, the CRL floating thickener and the improvement of analytical techniques. From a safety, health and environmental perspective there has been significant advances that the industry has much to be proud of. These include wetland restoration both in Australia and in the US, the restoration of farmland in Virginia and Capel, and the re-establishment of native species, for example at Eneabba and Richards Bay to name but a few.

Oct 5, 2011

By Bengt H. Fellenius

Session 2, Deep Foundation without Soil Excavation, has attracted no fewer than 22 papers dealing with subjects from soil improvement by grouting, injection, and deep mixing techniques through vibroflotation and special piles, including aspects pertaining to conventional driven and bored piles. In the short time available, it is not possible to both do justice to the papers and provide a critical review of the state-of-the-art. Instead, to meet the objective of making the next half hour worthwhile to the audience, I have chosen to comment on a few special points brought forward in the papers and thereafter to discuss more in detail a couple of aspects I have deemed to be of general interest. Four papers deal with jet-grouting, injection, and deep mixing techniques: DOMSKI, J. J. Reinforcement of subsoil under the foundations of historical buildings in Cracow using deep injection technique. RESTELLI, A. B, BERTERO, M., and LODIGIANI, E. Deep mixing technology to improve the bearing capacity of a very soft clayey soil under an earth embankment.

Jan 1, 1994

By Paul G. Swanson

This investigation was conducted to identify the principle causes of spoil instability problems in the Eastern Coal Province. The study was also conducted to develop a matrix to predict the strength and groundwater parameters necessary to conduct stability analyses on a proposed reclamation scheme. Suggestive methods to reduce spoil instability potential are also included. Numerous physical property, strength, compressibility, chemical and mineralogical tests were conducted on mine spoil samples obtained from 11 different surface mine sites. Site characteristics that influence the position of the post reclamation groundwater table were identified. Distinct regions within the Eastern Coal Province with high incidences of surface mine slides or high landslide susceptibility were identified. The application of the predictive matrices developed in this study is for surface mine sites mined and reclaimed in general accordance with the Surface Mine Reclamation Control Act of 1977. A review of current mining practices and the relative effect on spoil stability is included.

Jan 1, 1983

By Lionel C. Piuze

Introduction and Early History The British Canadian Mine is one of four operating properties of Asbestos Corporation, Limited, and is located in the town of Black Lake, Que., five miles southwest of Thetford Mines. In the early days of as1bestos mining, this .property was owned by a few small companies who later became part of the Asbestos Corporation. First .to commence mining operations on the property was the Coleraine Mining Company who, in 1885, began selling part of their large holdings in the area to various asbestos mining interests. Of these, the earliest active companies were Manhattan United Asbestos, the Glasgow and Montreal Asbestos Company, and the Anglo-Canadian, the last named later becoming the Standard and Dominion Asbestos Companies. Extraction of fibre was limited to what is now known as crude asbestos and the methods were primitive. Drilling was done .by hand and the ore was lifted by derricks operated by band winches. These were later replaced by horse power, but it was not until 1887 that the first steam-operated boom derricks were introduced, at the Anglo-Canadian mine. The ore was hand cobbled and the asbestos roughly classified and bagged. The waste rock, which by today's standards contained a considerable percentage of marketable fibre, was dumped near the pit. The first attempt to separate the asbestos from the host rock by mechanical means was made in 1888 by the G1asgow and Montreal Asbestos Company, then known as the Scottish-Canadian Asbestos Company, whose mill, erected in that year, was the world's first asbestos mill. Though the equipment was crude, the principles employed were the same as those used today with much larger units. The next steps were the use of rock drills, the adoption of steam rail transportation for moving mill rock, and conversion to the more flexible cable-derrick hoisting.

Jan 1, 1950

Jan 1, 1959

OWING to two large falls of ground which resulted in serious accidents occurring towards the end of 1908, it became evident that the "open chamber" system then in use was unsuitable for the conditions existing in the Mount lVIorgan mine. It will be admitted that in all mining operation, the first consideration is the economy of the system adopted, combined with its safety and ability to give the desired output. A sectional system with square sets has been introduced into the mine, in which due attention has been paid to these factors. In this paper a brief description of this system will be given. An outline of those previously used will be ineluded, as it is necessary to understand the eonditions which existed in the mine at the initiation of the sectional system. Outside the actual mining methods employed, various points that might prove of interest will be touched on.The square set system of mining has been in use throughout the stopes in the gold ore in the upper levels of the mine since underground operations were started in Mount Morgan.

Jan 1, 1910

By R. V. Ramani, W. Miola, R. Srikanth, S. C. Soboleski

"Dust control in high-production longwalls requires attention to operating practices and ventilation schemes. Several studies have shown that the shearer is the major source of dust on a longwall face. Support movement has not been regarded as a major source of dust in US longwalls. Yet, under certain conditions, 31% of the shearer operator's dust exposure can be due to support movement.Several methods have been developed for the control of shield-generated dust. But the need for better methods is apparent. In this paper, the amount of airborne, respirable dust generated per shield move is estimated from specially designed experiments on longwall faces. Ten experiments were conducted on five longwall faces in four mines. Each experiment involved one face visit and lasted three to six hours. The contribution of shield movement to the airborne, respirable dust concentration immediately downwind of the shield move varied between 0.12 and 1.75 mg/m3 in the five longwall faces. The mass of airborne, respirable dust gener-ated by shield movement was found to vary between 39 and 386 mg per shield move. The results from this study reveal that control of dust from longwall shields requires a combi-nation of approaches involving alternative operating prac-tices, reducing shield dust generation rate, increasing face air flow and decreasing personnel exposure.IntroductionIn 1992, longwall mining accounted for about 36% of US underground coal production, a 240% increase from a decade ago. The absolute longwall tonnages were 46 and 133 Mt (51 and 146 million st), respectively. Compared with room-and¬pillar mining systems, the longwall mining system is charac¬terized by higher recovery, enhanced safety and higher pro¬ductivity.However, personnel dust exposure on a longwall face is higher than in other types of mining. According to Mine Safety and Health Administration (MSHA) data, fewer longwalls were in continuous compliance with the applicable dust standard in 1992 than in 1989.Controlling shearer-generated dust and reduction of per-sonnel exposure to airborne dust have commanded attention in the design of longwall faces, operational practices and ventilation schemes. Studies in the United States and abroad have revealed that support-generated dust can be a major obstacle to compliance under certain conditions (Becker et al., 1989; Bradley et al., 1983; Jankowski and Organiscak, 1983; Jankowski et al., 1990; Organiscak et al., 1985)."

Dec 1, 1996

By Z. W. Nkosi, M. Sephton, J. H. Potgieter

The exhaust system is a complex assembly of various components performing important tasks in harsh environments. Carbon steels have been used extensively in exhaust systems, but pressure for lower cost, increased fuel efficiency; lower hazardous emissions, weight savings and increased life expectancy have shifted the emphasis to stainless steels. In response to the growing consumption of stainless steels in automotive exhaust systems, the need to properly evaluate their corrosion resistance properties in order to ensure their appropriate use, has increased substantially. This paper evaluated the most common corrosion and oxidation tests developed that are used and applied it to four common stainless steels often employed in hot end exhaust components. In a summary considering the weight loss of an alloy, it general corrosion rate and pitting resistance under all the test conditions for hot end exhaust components, results indicate that 434 was by far the most corrosion resistant alloy, followed by 1.4509 and 321, and lastly 304 was the least corrosion resistant. In general, the ferritic stainless steels, especially 434, outperformed the austenitic ones under all the test conditions.

Jan 1, 2006

By F. M. L. Mulaudzi

Behaviour studies of metal dusting processes and associated filamentous carbon formation were undertaken on Alloys 600, 601, and 800 using a simulated metal dusting environment of 25C0-70H2-5H20 (vol.%) at 650°C. These samples were studied visually and by optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM-EDX) and x-ray diffraction (XRD). Visual examination and SEM surface observation showed that Alloy 800 suffered metal dusting attack at an early exposure reaction period. The coke deposit amounts increased significantly with reaction time from 168 hours to 336 hours in Alloys 600, 601, and 800. Alloy 800 showed pitting after 168 hours' exposure, and the degree of pitting increased after 336 hours. XRD showed all these alloys had a common austenitic phase, with Alloy 800 also having ferritic metal particles. Alloy 800 after 168 hours' exposure had a complex phase mixture on the surface, consisting of ferritic Fe and austenitic FeNi phases. For coke deposit, there were also Fe304, Fe3C and graphitic carbon. The existence of Fe, Ni, and Cr metal particles, and also graphitic carbon in coke deposits, was confirmed by EDX analyses.

Jan 1, 2013

The U.S. Bureau of Mines conducted a series of laboratory tests in a full-scale model to determine the respirable quartz dust capture efficiency of an irrigated-filter collection system while testing different filter densities, different filter materials, preconditioning water sprays, and wetting additives in the spray water. Impactor samplers were operated upstream and downstream of the filter unit to determine overall dust collection efficiency. The impactor filters containing the 0.7-to 4.7-J.l-m size fractions were analyzed for quartz content, and these data were used to calculate quartz dust collection efficiency. The results of this testing indicated that (1) increased ftIter density improved quartz dust collection, but also resulted in a significant increase in pressure drop across the filter, (2) an alternate synthetic filter material improved dust collection without increasing pressure drop, (3) preconditioning sprays mounted in the system ductwork can have a beneficial effect on dust collection, and (4) additives to the spray water did not significantly increase dust collection.

Jan 1, 1990

By Parker JB

The Channar Iron Ore Mining Project (the Project) is a joint venture involving the Hamersley Holdings group (Hamersley) and the China Metallurgical Import and Export Corporation (CMIEC). The Project represents the first new iron ore mine development in Australia since 1971/72 and is the first major overseas mining investment by the People's Republic of China (PRC). The Channar mine is being constructed in the Pilbara region of Western Australia and will operate for more than 20 years supplying the PRC with 200 M tonne of high grade iron ore. The Project is configured to take advantage of Hamersley's existing production and support facilities. The Joint Venturers will invest A$280 million to achieve an initial production rate of 3 M tonne/yr and an additional A$120 million over the next 8 years to achieve full capacity of 10 M tonne/yr. Financing the Project to meet the requirements of both Hamersley and CMIEC, with the dependance of the Project on Hamersley's infrastructure, and in a depressed iron ore market, required an innovative financial structure to be arranged in a limited period. This paper describes both the financial structure and its implementation, and draws a number of conclusions regarding the financing of resource projects.

Jan 1, 1989