Search Documents

By David A. Larson

Preliminary laboratory experiments have been conducted by the Bureau of Mines to define the influence of bit geometry on methane ignitions as a step toward establishing safer mining-machine operating parameters. The experimental system was designed to simulate the operation of a continuous mining machine, using a drum-type cutterhead of normal diameter with a narrow cross section, permitting full-diameter drum cutting tests to be run on material representative of sandstone lenses (or inclusions) in coal seams. Two conical bit types were tested at shallow depths of cut with three drum speeds. Bits that rotated in the mounting block during testing did not produce ignitions. The ignition frequency for used bits was three to four times greater than for new bits at the same kerf depth.

Jan 1, 1983

In order to ensure safe mining and reduce surface damage in shallow multiple-seam mining, the failure characteristics of interburden strata with different coal pillar offset distances between pillars in the upper and lower seams, the distribution characteristics of stress concentration in coal pillars, and the development characteristics of stratum cracks and subsidence were physically investigated and also using UDEC2D software. Meanwhile, the effect of different coal pillar offset distances on the stress concentration of coal pillars and development of stratum cracks were studied. Based on those results, a formula for safe mining and reducing surface damage was established, which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seams. According to the results of the study, the optimal coal pillar offset distance (the side-to-side horizontal distance of the upper and lower coal pillars) between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage. The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

Jul 28, 2020

By Louis R. Iverson

Analysis of seed numbers present in topsoils (a grazed area, an ungrazed area, and two stockpiles) indicated that seeds of the most prevalent colonizers (e.g., Kochia scoparla, Setaria virdis, and Salsolo collins) were not present in the topsoil upon respreading but rather appeared by immigration from the surrounding areas. The grazed site had a seed density of over 7,700 seeds m-2 (of which 43% were from weedy species) and the ungrazed site had 3,900 seeds m-2 (of which 7% were weeds); the stockpiled topsoils had very low seed densities (255 and 520 seeds m-2). Seed densities and diversity decreased with depth on both the grazed and ungrazed sites; this was especially true on the grazed site where 94% of the seeds were found in the surface 7.5 cm. Several species were present in the seed bank (e.g., Hedeoma hispida, Artemesia ludoviciana, A. frigida, and A, abslnthlum) which were also found on the three and four year old mined sites in the aboveground vegetation survey. Seeds from these species may germinate after several years of dormancy, thereby starting populations on mined sites and enhancing plant diversity. Seed bank analysis was also undertaken on mined sites ranging in age of 2 to 6 years (plus an unmined site). Mined site seed densities ranged from 1630 to 3980 seeds m-2, with the four year old site having the greatest density (largely because of high Melilotus spp. populations); unmined site and stockpiled topsoil sample had lower seed densities. A significant positive correlation between total viable seed content and soil-water saturation percentage indicated that soil texture may influence seed viability/ dormancy (the. finer the material, the higher the seed population). As with the previous part of this study (and other studies), there was a poor correlation between the aboveground flora and the belowground seed composition.

Jan 1, 1982

By Andrea Koschinsky, Akira Usui, Michael Bau, Katja Schmidt, James Hein, Thomas Kuhn

Marine ferro-manganese (Fe-Mn) crusts and nodules are metal-rich chemical sediments that are archives of paleoceanographic proxies and potential metal resources and targets of deep-sea mining. Traditionally, crusts and nodules are subdivided into hydrogenetic, diagenetic, and hydrothermal types. While hydrogenetic Fe-Mn crusts are a potential resource for Co, Te, Pt, and REY, nodules are enriched in Cu, Ni, Mo, and Li, and hydrothermal deposits may be enriched in individual metals such as Mo, Ba, and Li, depending on the temperature and composition of the hydrothermal fluid. The different types of marine oxidic Fe-Mn precipitates, therefore, have different economic potential. Hence, a robust classification is not only helpful in the general geochemical characterization of such precipitates (and as such is a useful teaching tool, for example), but may also simplify the evaluation of their importance as a potential metal resource, which helps to prioritize exploration targets for deep-sea mining.

Sep 1, 2014

By R. L. Marek

The number of persons fatally injured in the California petroleum industry, in 1932 was 24, a decrease of 6, or 20 percent from the number killed in 1931. The decrease in the number of fatalities occurring in 1932 caused the fatality curve of the California petroleum industry to reach its lowest point in 10 years. Changing conditions in the oil industry--reduced personnel, decreased active field development, and curtailed production--have undoubtedly caused a part of this decrease, but continued accident-prevention efforts by the industry have also contributed to the reduction in the number of fatalities for 1932. The Bureau of Mines has analyzed and reported annually the fatalities in the California petroleum industry for a period of 10 years. Figure 1 shows the trend of fatal accidents during that period.

Jan 1, 1933

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014

By A. M. Hearn, J. R. Henning, A. S. J. Van Rensburg

The lining, together with the electrodes, forms the heart of the operation of a submerged arc furnace. Subsequent to a lining failure on M12 furnace during the early 1980s, Metalloys was active in investigating the concept of thermally efficient ?freeze? linings for its furnaces. The theory revolved around that, not only would, thermally efficient linings result in significant cost savings, but they would also last longer as a result of being subjected to less harsh operational conditions. After having proved the concept on the .smaller. furnaces, Metalloys decided to implement the concept on its largest submerged arc furnace, M12 Subsequent to having recovered from an impending failure of a lining installed in 1981 in M12 in the mid 1980s, Metalloys managed, through rigid lining management, to extend the life of this lining to 1999. At the end of 1999 the decision to replace the lining in the furnace with a ?freeze? lining was made and planning and design proceeded in earnest. This paper discusses the options considered in making the final decision. The features of the design of the lining are also discussed. Consideration is given to the furnace shell cooling system as a result of its importance in maintaining the thermal equilibrium in the lining. Note is made of the fact that the purchase of a .freeze. lining is an expensive exercise but that the time savings in the installation of the lining and the efficiency improvements during operation far outweigh the additional capital cost. The experience on M12 has been that the payback period of the marginal capital expenditure is less than three years. As a result of the opportunity to reline a furnace the size of M12 not presenting itself very often, the learning points from the installation of the lining and the operational advantages and disadvantages are significant. Finally, the point is made that the project had its pros and cons but overall the success of the project has been evident and, as such, the ?freeze? lining is likely to become the norm at Metalloys.

Jan 1, 2004

Mine ore, reduced to minus 71/2 in. by primary crushers, is stockpiled. Size reduction of the reclaimed material by secondary and tertiary crushers is achieved in a closed circuit crushing and screening plant. Screen products of minus 30 mm plus 6 mm lump, and minus 6 mm fines are stockpiled by conveyor and stacker systems prior to rail despatch 10 port facilities at Dampier. Crusher settings, determined from experience, are closely maintained to obtain the desired lump/fines ratio. Chemical and sizing analyses from automatically taken samples are used to maintain product specifications. The beneficiation plant upgrades the fines product when this is necessary. The recorded wear life of individual plant components is the basis of a planned maintenance programme.

Jan 1, 1970

By G. Lyle

Since its inception CEMI (Centre for Excellence in Mining Innovation) has focused on facilitating innovative solutions to the mining industry in six strategic research areas; GeoRisk, ConstructMine, ValueMine, FindMine, SustainMine and MineTech (visit www.miningexcellence.ca for details). This paper focuses on CEMI?s largest project to date, Ventilation on Demand (VOD). Energy consumption in mines can account for upwards of 40% of a mines operating cost, with a significant portion of this been consumed by the ventilation requirements. VOD provides a significant opportunity to reduce overall mine ventilation requirements and subsequently energy costs, while potentially increasing mine productivity. CEMI is currently in year 2 of an assessment of VOD, focusing on the financial, physical and equipment viability of utilizing such systems in both new and existing mines. This two year program, to be completed by March 31, 2011, is designed to systematically assess such a system to determine if and when it could effectively be applied in underground mines. The paper will describe the process by which the project was initiated, the demonstration projects established to capture data, the means to interpret the data and the modelling developed to calibrate and predict ventilation system requirements.

Oct 1, 2010

By R. G. Shen

The relation curve of strain and acceleration is presented in this paper. The steel pipe pile of 609.6 mm in external diameter driven by IDH-45 diesel motor hammer on the esturial shoal of Yangtze River. The ultimate bearing capacity of pile is analyzed by one dimensional wave equation and the effect of computational parameters of the equation is discussed.

Jan 1, 2010

By Richard Short

Shallow rainfall-induced landslides in residual and colluvial hillslopes and steep embankments are a common occurrence in many settings [1, 2, 3]. While occasionally posing a threat to property and life-safety, they more often present an ongoing maintenance problem and can lead to the initiation of larger failures. Typically, these slides consist of 2 to 4-foot thick translational movements of silty and clayey soils down slope through the reduction of strength from increases in pore water pressures. Direct surficial infiltration and indirect groundwater seepage are the normative triggers for failure. In the residential community of Blackhawk, California, located east of the San Francisco Bay, these types of landslides are a common occurrence (Figure 1). However, shallow landslides have also been a repetitive and constant problem along many state highways where steep embankments have been constructed in close proximity to busy thoroughfares. Given the real threat to property values in residential and commercial settings and the constant maintenance problem posed to lifeline structures such as utilities, roadways, and pipelines, new methods to deal with these landslides are needed.

Jan 1, 2007

By J. Laganiere

A considerable part of the sulphuric acid requirements of the Aluminum Company of Canada's Arvida smelter comes from the burning of 180-200 tons per day of zinc '"'sulphide concentrates in a 22-ft.-diam-eter fluidized bed roaster. The plant and its operation were fully de-scribed in a publication that appeared about ten year ago (1). A simplified flowsheet of the roasting and gas-cleaning sections of the plant is given in Figure 1. The wet zinc sulphide concentrates are un-loaded into a pug mixer, by means of a Pay loader, and mixed with water in a mixing tank to make a slurry of 80 per cent solids. The slurry is transferred to a .feed tank and then introduced into the roaster at a point four feet above the constriction plate, which is the height of the settled bed of zinc calcines. The roasting temperature is con-

Jan 1, 1963

By Qian (Ken) Liu, Remi Proulx

A large scale blast damage project was carried out over the past two years at INCO Ltd Manitoba Division co-funded by the Canada/Manitoba Mineral Development Agreement. The experiment was conducted at the T-3 Mine in two mining stopes with an experimental drift developed in the hanging-wall for the installation of monitoring instrumentation. The objective was to observe and subsequently to reduce ore dilution by monitoring the performance of blasts, the hanging wall movement, as well as the cavity of the open stopes.

Jan 1, 1995

By Peter Moser, A. Gaich, E. Grasedieck Zechmann

In The SMX Blast Controller is a novel tool for precisely controlling the geometry of a blast based on the technology of 3D imaging. It enables to derive precise information about the geometry of the face of a bench in a quarry from a pair of stereoscopic images taken from the bottom level of a bench with a calibrated standard digital camera. Apart from staking out the blast position with delimiters that mark the area to blast and taking then two images (freely), no further actions are required which allows performing the data acquisition without requiring any surveying skills. The 3D image generation and blast planning does not require special computer. It is estimated, that every blast foremen is able to work with the system after a one-day training as the system includes a high grade on automatism. The software package allows the blast foreman to design and stake out a blast, based on provided geometric values, such as burden, side spacing, hole inclination, sub-drilling, row number & distance and drilling pattern. The software connects these values with the 3D information acquired by the digital images. All the drill & blast information can be used also for blast documentation. The SMX Blast Controller overcomes also the problem of doing the back transfer from maps derived by surveying into nature as the resulting 3D image and all the information associated to it (hole position, etc.) can be correlated with the nature by visual comparison and the help of a single reference line, defined by two points. The system is designed to be used also in small to medium quarries. It can help, that the control of the geometry of the bench face and the precise design of the charge of the blast on a borehole per borehole basis will become an accepted daily routine.

Jan 1, 2006

By Lloyd A. Morley

The problems associated with the presence of organic materials and of water in explosion-proof enclosures used in high voltage, high capacity applications were examined through a literature search and theoretical reasoning. Information on volatilities is presented. The conclusion is reached that explosive pressures are significantly enhanced by inclusion of these materials.

Jan 1, 1976

By A. CHESTER BEATTY

SO much has been written about African, and particularly about Northern Rhodesian, copper during the past two years that I feel safe in assuming that you are familiar with the general background of the Rhodesian picture. Therefore, I will confine myself to certain of the high lights in connection with the history, geology, development, ore reserves, and contemplated mining methods in this relatively new and highly important copper field., Unlike most of the other great orebodies of the world, the Roan Antelope mine was not discovered by the hoof of a starving prospector's faithful burro; nor even, as its name might suggest, by a well-placed kick of protest from an antelope stumbling over a malachite outcrop. Late in 1905 an English prospector named Collier, traveling in the N'Dola district, came upon some natives using a green powder for medicinal purposes. Closer examination of the powder revealed that it ' was ground-up malachite. Collier endeavored to persuade the natives to tell him where they obtained this medicine, but' for a long time without success, because of the general feeling among the natives that they did not wish to reveal the resources of their land to the white. Finally however, - he persuaded- brie 'of-the elders to at" least take 'him part way toward, the- place where the malachite was supposed to occur. The bid took him, to a point on the lower regions of the Luanshya river and there left him with the instructions that if he followed the stream up toward its.

Jan 1, 1931

By Thomas C. Anderson

Tiedback walls are now recognized and accepted as a good solution for a variety of structural problems: ? Retaining Walls and Bridge Abutments in cut situations ? Landslide stabilization ? Repair/support of existing walls Acceptable techniques have been developed for anchoring in cohesive and granular soils and in any kind of rock. Methods have been developed for adequately protecting tieback tendons against corrosion and for testing every tieback to verify its long-term load-carrying capacity. However, the major problem that the industry faces today is how do we get constructable and economical tiedback walls contracted for and built with minimal claims. This paper will explore the issue of "constructability" through a look at specific problems from actual projects. From a research report from the Construction Industry Institute, Austin, Texas (1986), constructability is defined "as the optimum use of construction knowledge and experience in planning, design, procurement and field/operations to achieve overall project objectives." Maximum benefits occur when people with construction knowledge and experience become involved at the very beginning of the project." The design and installation of tiebacks has been developed primarily by specialty contractors; each contractor has evolved its own methods of performing the work, and consequently, many of the techniques are patented and proprietary. The real question is, how do we make effective use of this knowledge and experience during the design phase of the project?

Jan 1, 1991

The development of research activities at Risdon and the implementing of a policy of instrumentation in plant processes have, in recent years, entailed a considerable increase in research staff and created an urgent need for more space and modern laboratory facilities. The existing laboratories have been in use for 25 years and are now inadequate. New buildings have been authorized.The new buildings will comprise, firstly, a laboratory building of three floors giving a totai .floor space of approximately 11,000 sq.ft., and a pilot plant building as an annexe to the laboratory building, of approximately 4,900 sq.ft. The laboratory building will accommodate from 20 to 22 research workers, and additional plant operatives will be used for the control of processes in the pilot plant building. The new buildings are designed to provide facilities for three principal functions; the investigation and improvementof existing processes, the development of new processes up to the pilot plant stage, and the control and maintenance of instruments.LOCALITY AND ORIENTATION OF BUILDINGSThe site of the buildings is elevated ground on the eastern side of the main plant, near the main entrance and general office building. There will be no obstruction to sunshine at any time of the day, and the laboratory building will command views of wide radius from wooded hills across the River Derwentto the open sea on the south-eastern quarter.The buildings are located to provide space for future extensions. The main laboratory building faces approx...

Jan 1, 1949

By L C. Taylor, H U. Lesiste

This is a preliminary study of the statistical variation of the pressures on a target above a buried explosion. The data were taken at various distances from the charge centerline for three heights of the target above the soil and one charge depth of burial. All tests were conducted in saturated sand. They show that peak pressures and times of peaks are neither repeatable from shot to shot nor rotationally symmetric within a single shot. The peak pressure and time of peak at each location can be represented by cumulative normal distributions. The paper describes the means and standard deviations of these distributions at eight distances from the charge center for each height of target. These are used to determine the change in standard deviation of the distribution with distance from the charge centerline and height of target. The effect of scale on the mean peak pressures and times of peaks and on their standard deviations at a single scaled distance from the centerline of the charge are explored using various charge weights.

Jan 1, 2010

By Jaidev Sankar

The dream of constructing the new Second Avenue Subway in New York has finally become reality as the first construction contract package is currently underway. This first contract requires the construction a TBM Launch Box in the middle of Second Avenue from which a Tunnel Boring Machine (TBM) will bore two tunnels south to 63rd Street. This paper will discuss the design of this contract and how construction has progressed including preparation, site constraints, utility construction and com-munity impacts while highlighting the challenges of working in an urban environment. It will also discuss moving forward on this major project outlining the remaining contract packages including their scope and status.