Search Documents

By Maurizio Siepi, Fabio Santillan, Lyndon Bedford, Carlo Crippa

"Abstract: Wolf Creek dam, on the Cumberland River in Kentucky, US, operated and maintained by the Nashville District of the USACE, is the Corps' largest reservoir east of the Mississippi river. The 1748 m (5,736 ft) long Wolf Creek dam combines earthfill and concrete gravity sections. Construction began in 1941 and was completed in 1950. The dam showed signs of instability in the 1960’s, and in the late 70’s an in-depth project of rehabilitation was undertaken, using both grouting and secant piles. The works saved the dam, but in the late 90’s further signs of distress worried the Nashville district of USACE which, after a study conducted on the water seepage, concluded that construction of a new concrete barrier cut-off wall was needed. In 2009, the $341.4 USD million contract was awarded to TREVIICOS-SOLETANCHE JV.The new wall, located upstream of the concrete monoliths, has a minimum thickness of 60 cm (24 in.), and runs the length of the embankment, into the right abutment, for about 4,200 feet. The founding depth reaches 84 m (275 feet), well below the zone of solutioning. With a total surface approaching 92,903 sq.m (1,000,000 sq.ft), the Wolf Creek barrier wall is unlike any other project in the world.The construction of the cut-off wall followed a complicated but logical sequence of several operations, involving a variety of technologies: grouting, hydromill, directional drilling, and secant piles with reverse circulation. The intensive rock grouting program was aimed to minimize the risk of slurry loss and extend the positive cut-off further deep. Subsequently, an Encasement Concrete wall was installed with hydromill, toeing into the rock, to protect the embankment during the following phases. Smart holes were then drilled into the Encasement wall down to the final depth. Eventually, the holes were used to install the secant piles by employing the reverse circulation piling method.An extensive verification campaign has confirmed the superior quality of the cutoff wall consisting of 1200 secant piles, exceeding by far USACE’s requirements. The main project was substantially completed in early 2013. A small portion of secant piles wall will be installed downstream of the dam, to close the switchyard, finishing the project in the early months of 2014.IntroductionWolf Creek Dam is located on the Cumberland River in south-central Kentucky. The Nashville District of USACE operates this multipurpose dam to provide hydropower, flood control, water supply, and water quality benefits for the Cumberland River system and surrounding region. Lake Cumberland, created by the dam, impounds 7,400 million cu.m (6 million acre foot) at its maximum pool elevation of 232 m (760 ft) above sea level. This lake is the largest reservoir east of the Mississippi and the ninth largest in the United States, and attracts 4.89 million visitors, more than Yellowstone National Park (2.87 million).This paper describes the recently completed works for the rehabilitation of the dam, accomplished by TreviICOS-Soletanche JV with the construction of a new Barrier Wall."

Jan 1, 2014

By Richard F. Link

The objective of this report is to explain a statistical method for the summarization, organization, and classification of multivariate assay and other data from the mineral industry. Multivariate data are those characterized by several measurements at each data point, such as assay data from a mixed metal mine, or blast furnace data. A specific method of linear discriminant analysis, the Mahalanobis d2 procedure, is explained, starting from elementary principles; the d2 procedure enables many measurements at many data points to be studied by investigating the interrelationships among the data. The relation of linear discriminant analysis to other statistical methods for treating multivariate data, in particular the eigenvalue technique of factor analysis, is also explained. Example analyses are made on data from the Frisco mine, San Francisco del Oro, Chihuahua, Mexico. The data comprise assay values for silver, lead, copper, and zinc taken at some 19,000 sample points distributed into 91 groups.

Jan 1, 1967

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection and operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the high funding level program plan.

Jan 1, 1980

By C R. Ferrari

Residual subsidence is generally accepted as being about 5% of the total subsidence occurring within 12 months of all mining finishing. This paper looks at five case studies from different parts of the country, in various mining settings within a depth range of 430m to 760m. From a single seam single panel working to working the eleventh seam, all are within the concealed coalfield, similar to today's mining. The monitoring of subsidence continued for many years once the mining had finished and the results obtained are at considerable variance from the accepted norm. Subsidence has been found to carry on for up to eleven years after mining has ended, within a range of 8% to 45% of total subsidence. A highly significant factor was that subsidence, as a whole, was generally much more than predicted. The residual subsidence aspect has to he viewed in this context and in order to debate the subject at length, the causes of residual subsidence have to be balanced against the apparent inability to accurately predict subsidence. The results from the case studies were similar, even though the mining settings differed considerably. Subsidence of around 10% to 20% continued for several years after mining had ceased.

Jan 7, 1997

By Ernest M. Spokes

For bituminous and lignite coals the economic picture continued to improve as it has each year since the low of 1961, with production at 480 mil- lion tons in 1964 compared with 1963's 459 million tons. The anthracite industry produced 16.3 million tons in 1964 and 18.3 million tons in 1963. The industry is looking toward a further expansion; among the new developments will be a mining wheel producing 3 million tons of lignite per year in South Dakota. It is expected that electric power generation will continue to provide the market for most of the increase in consumption, with exports second in importance in the expansion. Improvements in methods of mining and transporting coal underground and in strip mines, and the cooperation of carriers in finding ways to reduce transportation costs to distant markets, have made possible these expansions. Research continues to reduce costs of mining, transportation, steam generation of electric power and production of steam for space heating and manufacturing processes, to retain some markets and expand others. Other research seeks to expand markets by developing fuel from coal which will be more attractive than competing fuels, by reducing sulfur and other sources of air pollution. Public relations efforts of the industry are bearing fruit in a greater acceptance of coal as a modern fuel.

Jan 2, 1965

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection Paid operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By James F. Kvitkovich, George V. Weisdack

Editor’s note: This is the second part of a two-part series on longwall mining in the United States. Part one was published in the December 2005 issue of ME (pp. 21-26). It provided a history of longwall coal mining in the United States. It also discussed the technology involved in the productivity gains and operational improvements. Boyd anticipates that U.S. coal production will increase by 61 Mt (67 million st) (6 percent) from 2004 to 2010. A combination of higher surface and underground mine production will be required to meet the projected market demand. Boyd’s projections of coal production by major mining methods are shown in Table 1.

Jan 1, 2006

By K. Viking

This article deals with some of the civil engineering related problems to be encountered when offshore wind energy projects transform from prototype offshore wind energy converter farms, developed and installed during the 1990?s, to commercial farms that?s currently planned to be built. The offshore wind energy converter (OWEC) installations encounter a wide range of problems, only partial of these are geotechnical. In Europe both onshore and offshore wind farms have, from a historical point of view, usually been founded by using the monopole technique, installed with traditional impact hammers, or by using gravitational foundations. However, the rapid development of bigger turbines and larger wind farms, together with increasing considerations of fatigue aspects, has lead to financial benefits of developing and exploring other foundation techniques. This paper reviews some Scandinavian experiences regarding critical components of the design phase in relation to connecting the superstructure to the ground, and some of the main considerations of how the loads applied to the structure are transferred to the surrounding soil.

Jan 1, 2013

By M. J. Fairweather, Keith Lee, Naseem Mian

"The initial metallurgical response of the lead flotation circuit at Cominco Alaska's Red Dog Mine was substantially below feasibility expectations. A program of diagnostic mineralogical analysis pointed the way to a number of process improvements, including simplification of the flow sheet and installation of a large flotation column as a lead cleaner. A diagnostic mineralogical analysis of the improved circuit shows that inadvertent activation of both sphalerite and pyrite has been substantially reduced, resulting in significant improvements in metallurgical performance. Directions for further improvements to the circuit performance are suggested by the recent analysis.IntroductionRed Dog is a high-grade, sedimentary exhalative (sedex) deposit with relatively simple mineralogy. The primary non-sulphide gangue minerals are quartz and barite, with minor barium carbonate (witherite). The iron sulphate minerals, siderotil, rosenite and copiapite occur variably throughout the deposit. Mineral texture is variable ranging from liberated sphalerite grains visible to the naked eye to intergrowths, particularly between sphalerite and galena, to less than ten microns. Both pyrite and marcasite are present. To date no enhanced reactivity of marcasite has been observed. For this discussion, ""pyrite"" will be used to refer to both iron sulphide minerals. In common with other sedex deposits, Red Dog contains organic and sulphur impurities."

Jan 1, 1997

By Robert H. Merrill

Several investigators have obtained solutions for the concentration of stress around circular, ovaloidal, elliptical, and rectangular holes in an elastic, isotropic, semiinfinite plate subjected to uniaxial and biaxial stress. These solutions are used to evaluate the changes in stress around openings immediately under the undercut normally used in conventional block caving operations. The evaluations are based on the assumption that a horizontal undercut removes most of the vertical component of a biaxial stress field. The location and magnitude of the significant changes in stress concentration around the opening are computed. Conditions under which the assumptions used in the evaluations may or may not be consistent with conditions around block caving mines are discussed, and examples of preferred opening shapes for a biaxial (hydrostatic) stress field are shown. This report is a summary of one phase of an investigation to establish design methods for the size and shape of mine openings used in block caving mining methods .

Jan 1, 1962

By Paul Hatmaker

"The Bureau of Mines recently has issued a general information circular covering briefly the origin and occurrence, properties, uses, exploitation, and marketing of diatomite. Since this publication was prepared, additional information has become available regarding one of the newer uses of diatomite — that as a filler in battery boxes. As this market is rapidly becoming one of the important outlets, a brief discussion of such use may be of interest.Diatomite is a mineral substance composed principally of the skeletal remains of diatoms. The skeletons of these microscopic flowerless water plants are made from silica present in the water in which these tiny plants live. The minute shells or ""casts"" accumu¬late in the bottom of lakes, ponds, or inland seas, and eventually become more or less consolidated into beds of diatomite.The uses of diatomite depend largely upon its peculiar properties. Diatomite is a highly porous substance and possesses marked absorptive powers. The large percentage of pore space makes the material very light in weight. It is relatively insoluble in most solutions.The largest deposits in the world are found in California, but diatomite occurs in many other Western States and also is found in a number of places along the Atlantic seaboard. Outside of the United States diatomite occurs in many countries; Algeria and Germany are among the largest producers.Usually diatomite is mined either by underground or open—cut methods. In some instances it may be dredged from lake and swamp bottoms. It must be dried prior to grinding or other preparation for market, and for many purposes must undergo a complex sizing and grading system for removal of such impurities as sand and clay and for classification of the material to the various sizes desired,"

Mar 1, 1931

By K. F. Unrug

In the paper a numerical modeling method is used for evaluation of a roof support system, which is commonly used in the US coal industry. The effectiveness of mechanical roof bolting with or without, header boards and steel straps are compared. This analysis takes into account the response of a shaly roof to changing environmental conditions in mines related to the seasonal changes in temperature and humidity of the intake air. Discussed are principles of roof support in coal mines and based on them a critical evaluation of header boards interaction with bolts and roof itself is carried out. Header boards create a soft inclusion within a much more stiffer system comprising bolt-rock. As an alternative to header boards, steel straps are analysed and corresponding results are presented. It is demonstrated that application of steel strap is beneficial from the stand point of stress distribution and maintaining tension on roof bolts. The laboratory investigations and modeling work previously undertaken by the authors, clearly indicate the detrimental effect of header boards on effectiveness of roof bolting. There are significant practical implications of the research considering that header boards are commonly used in mines. This practice has been probably originated from the wooden support used by mining in "pre-bolting era?, and it has stayed with coal mining based on tradition more than principles of engineering design. It is demonstrated that header board$ are detrimental and actually contribute to development of roof problems.

Jan 1, 1989

By K. Ananthanarayanan, R. I. L. Guthrie, S. A. Argyropoulos

"The low cost and availability of micro-computers and their peripherals provides the metallurgical engineer with the opportunity to use such computers in a wide variety of applications. In this paper, the authors describe the development of a low cost data acquisition system capable of measuring up to 8 analogue channels at a sampling rate of up to 5000 measure mentsper second. This system is equipped with proper hardware and software so that the micro-computer can be linked to a central computer facility such as the McGill System for Interactive Computing (MUSIC). This central computer facility is supported by an AMDAHL V7 computer. Using the present interface, communication rates between the microcomputer and the central computing facility can be as high as 9600 (baud).The above mentioned data acquisition system is currently used for monitoring dissolution kinetics of ferro-alloy additions in liquid steel. In addition to this, special software has been developed which enables the user of this system to monitor solidification rates of ingots, etc. As economic considerations are always important, comparisons have been made with existing recorders which show that the cost Of the present system is only 30 per cent more than a two-pen strip chart recorder.RESUMELa disponibilité et le bas prix des micro-ordinateurs et de leurs périphériques permet à l'ingénieur métallurgiste d'utiliser de tels ordinateurs pour diverses applications. Dans ce rapport, les auteurs décrivent le développement d'un système d bas prix pour l'acquisition des données, capable de mesurer jusqu'à huit canaux analogues jusqu’à une vitesse de 5000 mesures par seconde. Ce système est équipe avec son propre ""hardware"" et ""Software"" qui relient le micro-ordinateur d’un ordinateur central, comme le système de McGill pour computations réciproques (MUSIC). Ce central d'ordinateurs est soutenu par l'ordinateur AMDAHL V7. Utilisant cet "" interface"", la vitesse de communication entre Ie micro-ordinateur et l'ordinateur central peut atteindre jusqu'd 9600 (baud)."

Jan 1, 1980

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

By Sydney H., Ball

ONE of the important mineral discoveries of the eighteenth century was , that of the Minas Geraes, Brazil; diamond fields. The production of this and of .other diamond discoveries in neighboring states made Brazil the premier producer of diamonds, succeeding India; its 140 years of supremacy finally passed to- South Africa- 60 years ago. Three times have diamonds contributed heavily to Portugal's somewhat checkered financial history; first in the sixteenth and seventeenth- centuries when the diamond trade of India was controlled by its citizens residing in ,Goa, later in the late eighteenth and the first 75 years of the nineteenth century when the Brazilian fields were the world's source of diamonds, and now, when the Angola diamond mines are the principal source of revenue of its colony, Portuguese West Africa. Certain phases in the history of the administration of the Brazilian field are sufficiently curious to warrant description.

Jan 1, 1929

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

By R. S. Dean

"Interest in the nitrogen content of steel has increased sharply in the last few years. Investigations have indicated that its presence in steel has an important bearing on high temperature brittleness3, magnetic properties4, room temperature hardening5, and shock resistance. The steel producer may therefore look forward with certaintly to the necessity of controlling this element in a considerable proportion of his product. The literature, however, reveals a great many contradictory statements concerning the percentage of nitrogen which must be present to produce given effects on the properties of iron and steel. Most of these arise from a misunderstanding of the nature of the iron-nitrogen diagram near the iron end and a lack of recognition of the effect of state of aggregation on physical properties although both have been fairly well worked out.My thanks are due to Mr. J. L. Gregg, Prof. R. H. Dowdell, Mr, R. F. Mehl and Mr. H. C. Vacher for suggestions in connection with the preparation of this paper, and to Mr. C. H. Hefty and Mr. G. T. Motok for furnishing a valuable bibliography and translations of articles by Must and Duhr.The iron-nitrogen diagram in the solid state, so far as it concerns the nitrogen content of commercial iron and steel, consists simply in a solubility curve increasing with temperature. The important thing about this solubility curve is that without cold wore the iron nitride when precipitated does not go into solution on heating for long periods below 300°C. This slowness of solution is probably due to the fact that iron nitride when present as a separate phase has at these temperatures an equilibrium pressure of several thousand atmospheres7 and that therefore each particle of iron nitride surrounds itself with a layer of nitrogen. The precipitation of such an unstable crystal presents points of interest thermodynamically but we can not go into these here. It is quite well established that it precipitate. It can not diffuse then unless this layer is broken through or the temperature and pressure are increased to a point where the nitrogen is absorbed at an appreciable rate in the surrounding iron. This rate will depend on the degree of unsaturation of the iron and the excess pressure of the nitrogen above equilibrium pressure. The degree of unsaturation is determined by the temperature alone so that the temperature at which the rate of solution of the nitride becomes appreciable will depend on the pressure of nitrogen developed. This, in turn, will depend on the balance between rate of decomposition of the nitride and the rate o: flow of the iron. In annealed iron, this temperature of appreciable solution rate is between 300 and 350°C.8 By cold work, however, the elastic limit of the iron is increased, and conditions for the nitride to go into solution are reached at a much lower temperature, giving rise to the so-called blue brittleness. This brittleness and hardening is due to iron nitride going into solid solution and is not precipitation hardening."

Mar 1, 1931

Study on the New Flow Sheet and Wastewater Recycling for Xiaoliuguo Copper-Bearing Low-Grade Scheelite Ore

Sep 13, 2010