Search Documents

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner' us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.' for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi' F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

Properties of coal which are significant in relation to preparation for carbonization and conversion are reviewed, and existing coal preparation technology which has been used for production of cleaned coal of suitable ash content and petrographic composition for carbonisation, pyrolysis, hydrogenation and similar processes is described. Possibilities for application of this technology to some Australian coal seams is examined briefly. It is concluded that further survey work is required related to the optimization of selective crushing and concentrating operations, with the aim of maximizing production of quality products for carbonisation, etc mainly from Australian seams with only moderate coking characteristics.

Jan 1, 1980

By Scott Turner

The present rapid growth of coal stripping in the United States is a curious reversal of the tendency of mining to proceed from outcrop to depth. A combination of technical and economic factors bas stimulated the use of stripping methods until today many million tons of coal We being recovered by open cuts from sites that an earlier generation of engineers would have passed by as not commercially mineable or, if workable at all, only by underground methods. The total quantity of bituminous coal and lignite mined in the United States by stripping in 1928, the latest year for which detailed figures are available, was 19,789,000 short tons. Of this, 71,000 tons came from small workings not equipped with power shovels and 587,000 tons from properties in which stripping and underground work were carried on at the same mine; but as neither of these types is representative of modern stripping practice, they will be omitted in the discussion that follows. The total from strip pits proper in 1928 was 19,131,000 tons, produced by 176 pits employing 385 steam or electric shovels.3 Figures by States are given in Table 1. Detailed statistics will be found in Economics of Strip Coal Mining; a study by O. E. Kiessling, to be published by the United States Bureau of Mines.

Jan 1, 1930

By Natalia Konstantinova, Georgy Novikov, Pavel Rekant, Goergy Cherkashov, Olga Bogdanova

The economic interest of oceanic ferromanganese crusts and nodules is determined by high grades of major, rare and earth rare elements in these types of marine minerals [1]. Modern oceanic ferromanganese deposits have a global distribution with the largest fields in the Pacific Ocean. The Arctic Ocean still remains a poorly explored region. The first ferromanganese deposits from the deep part of the Arctic Ocean were recovered almost at the same time in 2012 both in US and Russian cruises to the Chukchi Borderland (1) and Mendeleev Ridge (2). Preliminary results of mineral deposits from the first area were reported at UMI-2012 by James Hein et al. [2]. We present here the data of ferromanganese deposits from the Mendeleev Ridge.

Sep 1, 2014

By W. Biermann

All industrial processes are economically driven, resulting in the ever increasing need for process optimization in order to stay competitive and profitable. Numerous models has been published depicting the optimization of the raw material usage in an arc furnace, as well as the thermal and electrical efficiency; however, to obtain a holistic view of the cost-effectiveness of the process one needs to expand the model to include the cost of all the operational variables. This project therefore aimed to not only include the raw material feeds and power consumption as input variables, but also the labour, maintenance, and environmental costs to generate an all-inclusive financial balance. In the end, the model was able to mathematically optimize the ferrochrome (FeCr) production process through evaluating the effect of a specified combination of input parameters. It could therefore be used as a tool to aid in managerial decision-making; to appraise and correspondingly adjust certain operational variables in order to achieve a maximum return on investment. This paper fully describes the reasoning behind the choice of the essential model components, the assumptions made during the models development, the calculation approach, as well as the advantages, limitations, possible applications, and areas for expansion of the final model. Through running simulations with plant data, it was found that the accuracy of final model remained fairly constant when applied to stable furnace conditions, but was met with a number of limitations when applied to more complex situations. These limitations could, however, be overcome through further development and expansion of the existing model to include a larger number of process variables.

Jan 1, 2012

By J. E. Tiffany, Z. C. Gaugler

In presenting this list of permissible explosives and blasting devices , the Bureau of Mines desires to call attention to pages 16 and 23 , outlining the conditions in use under which , and only under which , the explosive or blasting device is permissible . In view of publications recounting trade practice favoring the use of a blasting device without stemming , particular emphasis is placed upon condition 4 on page lt and condition 2 on page 23 .. An explosive or a blasting device enumerated in the permissible lists of this Bureau is not permissible in use unless it is properly confined with clay or other incombustible stemming .

Dec 1, 1943

By T. Dlokweni

Several Rockmass classification systems have been developed and used in Civil Engineering design and for underground mining operations. Some of these rockmass classification systems have been modified and used in the South African coal mining industry to quantify descriptive geological information for use in coal mine design and roof support selection. The Coal Mine Roof Rating (CMRR) system developed in the USA has been investigated in detail as part of the study. Advantages and disadvantages of the system have been identified by means of underground and surface borehole testing. Investigations into the rating systems in South Africa found that most of the rating systems used in the South African coal mining industry are for planning purposes, and are conducted on borehole cores. This study also highlighted that the rating systems being used are based on geology, and that the human factor plays a major role in the rating systems. To overcome these problems, all the classification systems used in South African coal mines have been benchmarked against impact splitting technique and documented. The best elements of these systems are combined into a new standard system that will be easily used by all mine geologists and rock mechanics engineers. Plusieurs systèmes de classification de la masse rocheuse ont été développés et utilisés dans le Génie Civil et pour les opérations d'exploitation minière souterraine. Certains de ces systèmes de classification de la masse rocheuse ont été modifiés et utilisés dans l'industrie minière sud-africaine pour quantifier l'information géologique descriptive utilisée dans la conception de mines de charbon et la sélection de soutènement du toit. Le système d'Evaluation de Toit de Mine de Charbon (CMRR) développé aux USA a été examiné en détail, comme part de l'étude présente. Tests en surface de trous de mine ont permis d'identifier les avantages et inconvénients du système. Une étude des systèmes d'évaluation en Afrique du Sud a révélé que la plupart des systèmes d'évaluation utilisés dans l'industrie minière sud-africaine sont utilisés pour la planification, et sont menés sur les carottes de trous de mine. L'étude présente a aussi souligné que les systèmes d'évaluation utilisés sont basés sur la géologie, et que le facteur humain joue un rôle majeur dans les systèmes d'évaluation. Pour surmonter ces problèmes, tous les systèmes de classification utilisés en Afrique du Sud ont été référencés en termes de technique de fissuration sur choc, et documentés. Les meilleurs éléments de ces systèmes sont combinés dans un nouveau système standard qui sera utilisé aisément par tous les géologues de mine et les ingénieurs miniers. Verschiedene Gesteinsmassenklassifikationssysteme wurden entwickelt und kamen im Design für Hoch- und Tiefbau und Untertageabbau zum Einsatz. Einige dieser Gesteinsmassen-klassifikationssysteme wurden modifiziert und sind in der südafrikanischen Kohlebergbauindustrie in Verwendung, um beschreibende geologische Informationen für die Anwendung im Design von Kohlebergwerken und der Firstabstützungsauswahl quantitativ zu beschreiben. Das in den USA entwickelte Kohlengrubenfirstbewertungssystem (CMRR) wurde als Teil der Studie im Detail untersucht. Vorteile und Nachteile des Systems sind mittels der Untergrund- und Oberflächenbohrlochprüfung gekennzeichnet worden. Prüfungen der Bewertungssysteme in Südafrika ergaben, daß die meisten Bewertungssysteme die in der südafrikanischen Kohlebergbauindustrie benutzt werden, Planungszwecken dienen und werden anhand von Bohrlochkernen durchgeführt. Diese Studie hob auch hervor, daß die verwendeten Bewertungssysteme auf Geologie basieren und daß der menschliche Faktor eine Hauptrolle in den Bewertungssystemen spielt. Um diese Probleme zu überwinden, wurden alle in südafrikanischen Kohlengruben benutzte Klassifizierungssysteme vergleichsweise in Hinblick auf Spaltschlagtechnik überprüft und dokumentiert. Die besten Elemente dieser Systeme werden in ein neues Standardsystem kombiniert, das leicht von allen Grubengeologen und von Gebirgsmechanikingenieuren benutzt werden kann.

Jan 1, 2003

By Corate L. Brierley

Low-grade porphyry copper ores containing chalcopyrite as the primary mineral was leached by two strains of acidophilic, thermophilic microbes belonging to the genus Sulfolobus. Leach tests were conducted in glass columns heated to 60-70° C. Pinto Valley and San Manuel ores sized to -1/2 inch + 50 mesh were effectively leached by the thermophilic organisms, but pinto Valley and Cyprus Bagdad ores sized to -2 inch + 1/2 inch resisted leaching. Aeration did not contribute measurably to bacterial copper extraction, since two columns, one inoculated and one sterilized, having a rest/ leach cycle without recurrent aeration exhibited copper extraction patterns similar to those of the aerated columns. Distilled water can be substituted for 9K medium without diminishing copper extraction. Decreasing the pH of the leachate to about 1.8 enhanced the extraction of copper from pinto Valley ore with the thermophilic microbes. Thiobacillus ferrooxidans was found to be relatively ineffective at copper extraction from pinto Valley ore. Of eleven solvent extraction reagents tested, Adogen 364 and Warsol at concentrations of 0.1% and 0.012 were inhibitory to oxygen uptake by the two Sulfolobus strains. Di-2-ethyhexyl phosphoric acid at concentrations of 0.1%, 0.01% and 0.001% were totally inhibitory to the respiration of both organisms.

Jan 1, 1979

By B. C. Viljoen

"SynopsisCommencement of the next phase of the Lesotho Highlands Water Project is a year or so away from becoming reality. Some 50 km of tunnels in the form of access adits, shafts, diversion tunnels, and main waterways will be constructed. Sprayed concrete will form an integral part of the temporary and permanent rock support systems that will be installed. Furthermore, the use of sprayed concrete as a final tunnel lining solution was proposed as a viable alternative to concrete linings in the feasibility studies that preceded the forthcoming implementation phase.The aim of this paper is to make the reader aware of all the sprayed concrete related issues that engineers tend to grapple with during the design and construction of tunnel projects and other underground works. Primarily, these issues would include selection of applicable design parameters, technical specifications, construction application methods, quality control and, most importantly in the context of final or permanent linings, the durability of sprayed concrete.The International Tunnelling Association (ITA) Working Group (WG) 12 has been tasked specifically to publish a set of recommendations on the Quality and Control of the Application of Sprayed Concrete and the Testing of Sprayed Concrete for Durability. These tasks were also further explored at the recent World Tunnel Congress (WTC 2015) that was held in Dubrovnik, Croatia at the end of May 2015.IntroductionSprayed concrete is presented in a variety of shapes, designs, forms, application methods and accompanying terminologies including shotcrete, gunite, pneumatically applied concrete, and the like. The International Tunnelling Association (ITA) decided to standardize on a single terminology, namely ‘sprayed concrete’, in order to simplify specification, interpretation of guidelines, and codes of practice."

Jan 1, 2015

By Jesse A. Miller

ALTHOUGH the element titanium was discovered by William Gregor in 1790, over a hundred years passed before it was put to commercial use. The first commercial application of titanium was as an alloy additive to iron and steel, and the first ferroalloys were produced domestically in 1906. Titanium pigments were developed somewhat later and have been produced in the United States since 1918. The use of titaniferous material in welding-rod coatings first gained acceptance ill the mid-30's. The metal titanium has only had commercial importance since 1948; domestic production for that year was 10 tons. The relative importance of these major uses of titanium in various forms may he gaged by the consumption of titanium dioxide (Ti02) for these purposes in 1954. Of a total of 440,000 short tons of Ti02 consumed in 1954, 95 percent of the total was consumed for pigments; 2 percent for welding-rod coatings; 1 percent for non-titanium-base alloys and carbide; and 2 percent for miscellaneous uses. The titanium-metal industry is in its infancy, but it has more than doubled its output every year from 1948 to 1954, reaching 5,370 short tons in 1954.

Jan 1, 1957

By T. Iwanowski

Stress wave measurements and calculations are often used to make a safe determination of the bearing capacity and the integrity of driven piles. Some applications to the restoration of old buildings in the Old Town of Stockholm are referred to and especially analyses of measurements combined with simulations are discussed here.

Jan 1, 1991

By J. Little

It is common practice for underground mine plans to be created sequentially, where results from one planning process form the input data for another. While this is practical for manual methods, computerized optimization techniques should consider an integrated approach to creating the global mine plan. This is because optimizing an individual mine planning process, such as stope layouts, introduces a likelihood of increasing costs or decreasing revenues associated with other areas, such as production scheduling, as harmful decisions must be balanced. Considering the interaction and influence that individual underground mine planning processes have on each other during optimization will provide more profitable results than if these are ignored. Optimization techniques for stope layouts and production scheduling are reviewed. An integer programming model is proposed that allows for either integrated or isolated optimization. Both approaches are separately applied to a block model. The results demonstrate the model?s ability to produce optimal long-term sublevel stoping mine plans and the benefits of using an integrated approach. Keywords underground mine optimization, stope layouts, underground production scheduling, integer programming, mathematical programming application.

Oct 1, 2013

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By L. L. Hirst

In 1944, the 78th congress of the United States enacted Public Law 290, which directed the Secretary of the Interior, acting through the Bureau of Mines, to furnish industry with basic information and cost data for the development of a synthetic liquid fuels industry. Recently published information with respect to the cost of synthetic liquid fuels processes indicates a wide variation in estimated results. To clarify the results and inconsistencies for the hydrogenation of coal, the Bureau of Mines has prepared preliminary designs and calculated detailed investment costs from which the operating costs to produce 30,000 barrels per day of liquid products, mainly gasoline, by coal hydrogenation were obtained.

Jan 1, 1949

By Jon Y. Kaneshiro, Eric Dawson, Pooyan Asadollahi, Steven Hunt

This paper provides updates to the paper published by the lead author at RETC 2011 with a summary of developments in technologies, products, and approaches to corrosion analyses of gravity sewer tunnels and microtunnels. This paper presents approaches in evaluating degradation of reinforced concrete liners. Also, the carbon footprint of conventional concrete liners and alternative “green” liners are compared and their life cycle costs are considered. A few case histories from the past decade are provided indicating the latest and emerging trends in liner protection.

Jun 13, 2023

By Innes J. A

The structural variations occurring in pellets of finely divided mixtures of iron ore and coke breeze, metallized by firing at elevated temperatures, have been examined microscopically. For any given pellet composition, time and temperature are the two most important factors in determining the development of the bonding processes.INTRODUCTIONThe success of sintering and pelletizing processes in the agglomeration of fine iron ores for blast furnace use has brought about rapid changes in thinking relative to methods of preparing furnace burdens. Increases in productivity with the use of sinter emphasize the advantages of a stable, uniformly sized furnace feed. Current practice is to produce a self-fluxing sinter containing most of the lime requirements of the furnace incorporated as a stable medium (Figgis and Charker, 1962). The elimination of fine material from the burden allows greater stack permeability and smoother operation.Sintering and pelletizing of iron ores with or without the incorporation of fluxing compounds has conditioned operators to the extent that it is now considered possible that all components of the burden may eventually be beneficiated in one form or another. Investigations are in hand to improve the quality and sizing of coke, which occupies the major part of the burden volume (Callcott, Innes and Brown, 1961; Innes, Gregory and Worner, 1963). Interest is also being revived in methods of pre-reducing iron ores prior to charging to the furnace (Hansen, Melcher and Fine, 1961). Recent experiments in a small experimental blast furnace (Melcher, 1963) show that charging of semi-metallized pellets can give rise to a production increase of 55 per cent...

Jan 1, 1963

By D. A. Stanley

The Bureau of Mines has developed a simple titration technique for determining the points of zero charge (PZC) on minerals. The technique consists of titrating a mineral slurry with the potassium salt of polyvinyl sulfuric acid (PVSK) in the presence of an indicatory dye and a positively charged polymer. Values obtained by this simple method are in good agreement with values found in the literature.

Jan 1, 1982

By Sunil S. Basarkar, Dilip M. Dewaikar, Rajesh H. Gajjar

"A load transfer program AXPILE was developed for simulation of the loadmovement characteristics of socketed piles of the Mumbai reg ion. This program used empirical relationships for ultimate shaft resistance at pile-rock interface recommended by Zhang and Einstein (1998). According to their recommendation, ultimate shaft resistance at pile-rock interface is related to the square-root of uniaxial compressive strength of intact socket material by a parameter C, which ranges from 0.4 for smooth sockets to 0.8 for rough sockets. Results of three instrumented pile load tests were compared with the AXPILE generated results. The comparison of analytical and field estimates of the unit shaft resistance confirm the recommendations of Zhang and Einstein (1998) on the unit side shear parameter c,, which was found to be in the range of 0.35 to 0.67.INTRODUCTIONInstrumented pile load tests were carried out on the test piles at the Bandra-Worli sea link project in Mumbai city of western India. High capacity socketed piles were required to take up loads from the superstructure. Hence, in addition to the available toe resistance, an accurate measurement of the shaft resistance in socket portion was desired. The instrumented load tests incorporated Osterbergcell (0-cell) assisted by strain gauge instrumentation to estimate the shaft resistance mobilization in the socket portion.AXPILE load transfer program was developed for load-movement simulation of socketed piles (Basarkar, 2004). The load transfer algorithm based on Coyle and Reese (1966) was incorporated in this program, which used empirical correlations and functions to account for load transfer in piles through shaft and toe resistance.This paper compares the computed unit shaft resistance from the AXPILE program with the measured values recorded from the instrumented pile load test."

Jan 1, 2005

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.