Search Documents

By R. B. Porter

Bench-scale tests were performed by the Federal Bureau of Mines on lignite and subbituminous coal at pressures to 1,000 p.s.i.g. (pounds per square inch gage) in atmospheres of hydrogen or nitrogen to obtain information concerning the influence of pressure on carbonization of normally noncaking coals. The distribution of gaseous, liquid, and solid products as a function of processing pressure was determined. Except for special experiments, the carbonization was at 940° F. In a hydrogen atmosphere above 400 p.s.i.g., agglomeration of the solid residue (especially with lignite) became noticeable and increased directly with the processing pressure. Although in some instances the solid particles fused together, the mechanical strength of the agglomerate was always low. On the basis of visual inspection, the coals agglomerated in the following order of decreasing intensity: (1) Steam-dried lignite; (2) lignite; and (3) subbituminous coal. Addition of lignite tar in quantities to 25 percent by weight of charge did not increase agglomeration or change the carbonization characteristics of the coal.

Jan 1, 1961

By H. C. Horwood

INTRODUCTION THE Argosy Gold Mines, Limited, which joined the ranks of active Ontario gold producers during the summer of 1936, holds a group of 21 claims on Casummit lake, in the Patricia portion, district of Kenora, northwestern Ontario. The Company is developing and mining goldbearing quartz veins that occur in a series of greywackes and slates of probable Keewatin age. The writer made a geological examination of the property and the surrounding area for the Ontario Department of Mines during the early part of the field season of 1936. This paper is a report on the general geology, structure, and ore deposits at the mine and is based almost entirely on data compiled during the examination. HISTORY Mineralization was first discovered on the property in May, 1929, by A. F. Hewitt, who, with J. A. Borthwick, decided that the country had prospecting possibilities and commenced work in April. Mr. Hewitt staked, and with his partner, J. Ziyone, still holds the group of claims lying immediately east of the present Argosy holdings. Mr. Borthwick staked six claims, K.R.L. 9,681 to 9,686, inclusive, adjoining Hewitt's on the west and later added claims K.R.L. 9,733 to 9,740, inclusive, to his holdings. F. Fiskness, who was also prospecting in the region, discoveted No. 1 vein on Borthwick's claims, and with his two partners, L. Parth and H. Jones, staked claims K.R.L. 9,758 to 9,763, inclusive, to the northwest of Borthwick's and Hewitt's ground. In July, 1929, the Casey Mountain Operating Syndicate, which held ground to the northwest, secured an option on Borthwick's claims. The Fiskness-Parth-Jones property was added in January, 1930, to protect the west dip of the veins. During the winter of 1930-31, the veins were explored by diamond drilling, No. 2 for a length ?of 900 feet and a vertical depth of from 51 to. 375 feet? and No. 3 .t~ a slope depth of 175 feet. I~ August, 1.931, after the msrallat10n of a miming plant, the Casey Summit Gold Mmes, limited, was incorporated to take over the property from the Syndicate. The Maple leaf Mines optioned a controlling interest in the stock in August, 1933, and on September 17th, 1934, brought a 50-ton amalgamation mill into production. From early in October to December 27th, 1934, when the mill was closed down, 4,094 tons of ore were treated to yield 887.89 ounces of gold and 87 .26 ounces of silver( ! ).

Jan 1, 1937

The Role of Mineral Processing in the Development of Cement with Low Carbon Emissions

Sep 13, 2010

By Timothy J. Myers

Expansion and the economic growth in the southwestern region of Missouri necessitated the expansion of State Route 249 and the construction of a new interchange to provide service to the Joplin, Missouri area. The project is located above a former lead and zinc mine in Jasper County, Missouri and includes a five bridge interchange connecting State Route 249 and US Route 171. The variable subsurface conditions, both natural and manmade, prompted the design team to use ground improvement via grouting and small diameter micropiles to provide support for several of the bridge foundations on the project. The scope of work included mine shaft closures, 56,000 ft of overburden and rock drilling, 11,139 ft of micropiles, 524 cy of balanced/stabilized high mobility grouts, and over 8,700 cy of low mobility grout. The selection of the grout used was based on the actual subsurface conditions. Low mobility grout (LMG) was used in voided conditions and for closure of the mine shafts encountered during the excavation. High mobility grout (HMG) was used in fractured rock with the goal of improving the mechanical properties of the rock underneath the future bridge footings and controlling grout volumes during micropile installation. The split spacing method was utilized for both LMG and HMG holes. Geology of the project site subsurface consisted of extremely variable bedrock with strong to very strong limestone, chert, breccia, extremely weak shale, and weak to strong sandstone. Previous activities associated with the mining disturbance (such as partial filled vertical mine shafts, shallow and deep mine horizons, modified hydrology including artesian conditions) further complicates the site subsurface conditions. Real time monitoring and recording of all drilling and grouting parameters was conducted to assist in the evaluation of in-situ geological properties of the site in order to modify the ground improvement and micropile program as necessary. This paper will discuss the design and execution of the ground improvement and micropile program. The project is an excellent example of the use of multiple ground improvement and foundation support techniques combined with real time data analysis to provide a foundation support solution for a complex geological environment.

Jan 1, 2009

CENTRAL mine ore consists mainly of galena and marmatite in a siliceous and rhodonitic gangue, the average assay values being approximately 11.5 oz. per ton Ag, 14.5% Pb, 14.5% Zn, 1.3% Ox Pb, 0.3% Ox Zn.Owing to the 1923 fire in the underground workings, much of the ore now being mined has been subjected to a certain amount of oxidation, as shown by the oxidised values above.This factor is of great importance from a flotation point of view, as a sulphide surface which has been subjected to the influence of oxidation is not as amenable to flotation concentration as a fresh sulphide surface. The importance of this factor is increased when a differential flotation is to be made, and, as in the case of Central mine ore, the sulphide, which is to be floated first, has been oxidised...

Jan 1, 1931

By J. Kazakoff

"The success of gold recovery at the Jolu gold mill depends on many variables. The most important ones are the people, the ore body, plant design parameters, equipment selection and cost control. This paper will briefly hiqhlight the above, the main focus, however will be on the gravity gold circuit.The gravity circuit requires judicious operator attention in order to operate properly. In return the circuit gives immediate visual results for mill peopleIntroductionThe development of the Jolu property to the production stage was carried out quickly, efficiently and economically. The property became a gold producer ahead of schedule and under budget.The Jolu property is a joint venture between International Mahogany Corp., a 70% partner, and Corona Corporation, a 30% partner. Corona Corporation operates the Jolu Gold Mine, located 140 kilometers north of LaRonge and 520 kilometers north of Saskatoon."

Jan 1, 1990

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

By Robinson KJ

There has been much debate in recent years regarding the number of Geology (Earth Science) graduates produced in Australia. The key variable has commonly been assumed to be the placement of graduates in the mineral and petroleum industries. Although not wishing to deny the importance of this element, we contend that Geoscience studies should be given to a wider variety of graduates. The essence is to make students and future citizens more environmentally aware. INTRODUCTION Geoscience is fundamental to exploration and to the well-being of the minerals industry and hence the Australian economy. The value of mineral primary products exports for the past three years has been: 1895 $15.3 billion 1986 $14.8 billion 1987 $16.3 billion (Data source: B.M.R) The mining industry supplies about 40% of Australia's export earnings. However the overall value of Geoscience to the Australian economy is much greater. At the opening of the ANZAAS conference in Townsville during May 1987, Sir Bruce Watson , Chairman of the Mt. Isa Mines Ltd., made a plea for a national re-examination of the way science is taught in secondary schools. In particular he emphasized the point that the community should be more aware of the importance of Geoscience and the value of the mining industry to Australia.

Jan 1, 1989

By M Bannear, C Stanton

Since 2008, Arrium has been developing and commissioning a new low-grade hematite ore benefication plant (or OBP) at its Iron Baron mine site.The Iron Baron mine, which was closed in the 1990s, could not consistently yield the high-grade hematite required for pelletising. However, in todayÆs market, the 12 Mt of waste dumps represent a significant low-grade hematite resource, ideal for benefication.Initially, an internal scoping study and several sampling campaigns were conducted to determine the ability to upgrade the available low-grade dump material to a product suitable for export. Test work was conducted at Mineral Technologies (formerly CPG), and included high intensity magnetic separation, spiralling and jigging. Due to promising results from a wet processing circuit, Arrium engaged Mineral Technologies to design a flow sheet that could provide 1 Mt/a of a mixture of high-grade lump (-32 + 8 mm) and fines (-8 mm) products for export.With construction of the plant completed in late January 2012, Arrium, in conjunction with Mineral Technologies, began two commissioning phases. Each phase ended with a toll gate to prove the plantÆs capacity to reach rate and desired grade. After an initial period of running on water, feed solids were introduced to the plant and troubleshooting of bottlenecks began. The first toll gate, whereby the plant was required to run for 24 hours at an average feed rate of 200 t/h (80 per cent of design rate), was completed on the 1 March 2012. Further troubleshooting and resolving of issues allowed the plant to steadily increase feedrate while maintaining good availability and grade. The second toll gate required the plant to run for 72 hours at an average feed rate of 200 t/h while meeting grade, yield and water consumption targets. Sampling campaigns were conducted during this period to track the performance of key equipment. Completion of the test, and full handover of the plant to Arrium, was completed on the 21 April 2012.Although the formal commissioning phases had been completed, ongoing optimisation of the OBP continued, ensuring that all major equipment was working to produce the optimum yield and grade. Sampling campaigns were conducted on the jigs and spirals, with results and correlations used for operations documentation.Overall, with successful completion of the final acceptance tests, the commissioning of the Iron Baron OBP has been established as a major success achieving all production and quality targets as per the original design intent.This paper will focus on the successful commissioning and ramp-up performance of the plant however reference will also be made to the key development stages involved with the development of the project.CITATION:Stanton, C and Bannear, M, 2013. ArriumÆs Iron Baron hematite beneficiation plant - a success from start to finish, in Proceedings Iron Ore 2013 , pp 547-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By C. H. Riggs, Kenneth H. Johnston

The application of modern secondary-recovery methods has made possible the the extraction of more than 13 million barrels of crude petroleum from the eastern part of the Delaware-Childers field Nowata County, Okla., over and above the production that might have :been expected by continuing primary production methods, including the use of vacuum. Foremost among the secondary-recovery methods used in this foil was the repressuring of the Bartlesville sand with air and gas through injection wells spaced on sym-metrical patterns. Between 1925 and 1945, about 51 billion cubic feet of air and gas were injected into the producing formation, and the total recovery was increased from, 25 million to about 40 million barrels of oil. To produce as much as possible of the 28 million barrels of recoverable oil remaining in the sand will require the initiation of systematic water-flooding projects on many properties and the continuation of air and gas injection on others.

Dec 1, 1946

By Wojciech Klecan

Cobb County, located on the northwest side of Atlanta, GA, is continually growing and, like many other metropolitan areas, it needs to increase the capacity of its waste water system to meet future demand. The Cobb County Water System (CCWS) is the responsible agency for water distribution, waste water collection and treatment in most areas of the county. CCWS, one of the most progressive agencies in the metro-Atlanta area, is addressing its future waste water capacity needs in the southern part of the county with the construction of the South Cobb Tunnel and Pump Station. This project consists of an 8.8-km- (5.5-mile-) long, 8.2-m- (27-ft-) diameter, tunnel boring machine (TBM) excavated waste water storage and conveyance tunnel; six tangential vortex-flow intakes ranging from 1,533 to 5,700 L/s (35 to 130 mgd) peak flow capacity, two construction shafts, six 1.8-m (6-ft) finished diameter connecting tunnels ranging in length from 6 to 975 m (20 to 3,200 ft) and a 5,700-L/s (130-mgd) wet/dry pit pump station. The pump station will have a semi-circular wet well with a dividing wall that extends almost to the top of the shaft and a spilt dry well for reliable operation. Roller gates will control the flow to the wet well from the tunnel. The pump station will have six 1,420 L/s (32.5 mgd) pumps and two sets of stair wells and elevators. With a finished diameter of 32 m (104 ft) and a depth of 62 m (204 ft), this is the largest pump station shaft constructed so far in Georgia for the dewatering of a waste water tunnel. The pump station shaft was also the highlight of the well attended and successful 2009 Shaft Design and Construction Short Course held in Atlanta, Sept. 10-11. The two-day course was sponsored by the Underground Construction Association of SME and Pennsylvania State University and concluded with a field trip to the pump station shaft. The tunnel starts south of the city of Austell and finishes at the South Cobb Water Reclamation Facility (WRF), located on the banks of the [ ] Chattahoochee River just north of Interstate 20 (Fig. 1). The South Cobb Tunnel will run 30 to 137 m (100 to 450 ft) below the surface, with an average depth of about 91 m (300 ft), through metamorphic rocks (Fig 2). The construction contract was awarded to Shea-Traylor JV with the lowest bid price of $305 million and notice-to-proceed was given on July 14, 2008. Jordan Jones & Goulding, Inc. (JJG) is the project designer and performed the geotechnical investigations. Parsons/Jacobs Associates is the construction manager. The South Cobb Tunnel is CCWS?s second deep hard rock tunnel. The 15.3-km- (9.5-mile-) long, 5.5-m- (18-ft-) diameter TBM excavated the Chattahoochee Tunnel was the first deep tunnel to be construced in Cobb County. Construction began in 2000 and the project was completed four years later. It is located about 16 km (10 miles) northeast of the South Cobb Tunnel in similar geology. It was designed by JJG to meet east Cobb?s long-term waste water capacity needs and provide flow equalization to the R.L. Sutton WRF. The Chattahoochee Tunnel was named ?Outstanding Civil Engineering Project of the Year? by the Georgia Sec-tion of the American Society of Civil Engineers in 2006.

Jan 1, 2009

By J. A. Finch, D. Lin

The robustness of the large-sections correction procedure, Hill's fast approximation, Barbery's correction and the PARGEN correction was examined by comparing their ability to reconstruct the true liberation distribution using sectioning data from computer-generated spheres. The results indicate that the flexibility of a correction procedure is related to the assumptions it makes about the continuity of the liberation distribution, locked-particle characteristics and ore texture. Overall, the large-sections procedure appeared to be the most generally applicable. The Hill fast approximation performed well, but this was probably because it partially incorporates the sphere model; the performance of the PARGEN and Barbery corrections varied from case to case.

Dec 1, 1995

By S. E. Phillipson, P. L. Tyrna

Lineament analysis, a remote sensing application for geological structures, has been criticized for reliance on subjective interpretations. The Mine Safety & Health Administration’s Roof Control Division performs lineament analyses with a technique that removes much subjectivity. Study areas are viewed on satellite images with software that allows examination under artificial sun azimuths and elevations. Extraneous lineaments are removed through successive steps of superposition, resulting in selection of the most robust linear features. Field investigations revealed a strong coincidence of joint and fault zones that were parallel with projected lineaments. The Roof Control Division’s successful identification of lineaments associated with roof falls and highwall failures has prompted some mine managers to incorporate lineament analysis as a mine-planning tool. The identification of potentially hazardous ground conditions will allow mine operators to obviate safety concerns that might otherwise adversely affect miner health and safety.

Jan 1, 2002

By H W. Wu, D Humphreys

The structure of a comprehensive research project into mine fires study applying the Ventgraph mine fire simulation software, preplanning of escape scenarios and general interaction with rescue responses is outlined. The project has Australian Coal Association Research Program (ACARP) funding and also relies on substantial mining company site support. This practical input from mine operators is essential and allows the approach to be introduced in the most creditable way. The effort is built around the introduction of fire simulation computer software to the Australian mining industry and the consequent modelling of fire scenarios in selected different mine layouts. Application of the simulation software package to the changing mine layouts requires experience to achieve realistic outcomes. Most Australian mines of size currently use a ventilation network simulation program. Under the project a small subroutine has been written to transfer the input data from the existing mine ventilation network simulation program to æVentgraphÆ. This has been tested successfully. To understand fire simulation behaviour on the mine ventilation system, it is necessary to understood the possible effects of mine fires on various mine ventilation systems correctly first. Case studies demonstrating the possible effects of fires on some typical Australian coal mine ventilation circuits have been examined. The situation in which there is some gas make at the face and effects with fire have also been developed to emphasise how unstable and dangerous situations may arise. The primary objective of the part of the study described in this paper is to use mine fire simulation software to gain better understanding of how spontaneous combustion initiated fires can interact with the complex ventilation behaviour underground during a substantial fire. It focuses on the simulation of spontaneous combustion sourced heatings that develop into open fires. Further, it examines ventilation behaviour effects of spontaneous combustion initiated pillar fires and examines the difficulties these can be present if a ventilation reversal occurs. It also briefly examines simulation of use of the inertisation to assist in mine recovery. Mine fires are recognised across the world as a major hazard issue. New approaches allowing improvement in understanding their consequences have been developed as an aid in handling this complex area.

Jan 1, 2005

By Johan Finsteen Gjødvad, Mathias Jern

The paper is part of the ongoing work of the Environmental committee of EFEE. To assist the European experts working with explosives one of the aims is to improve the common knowledge of similarities and differences between national legislation, standards or guidelines on vibration monitoring and other environmental monitoring during blasting in Europe and abroad. This has been done by use of an online survey through the most of 2018. Questions have been raised on vibration monitoring during blasting. The existence of norms, guidelines or standards and how they are used. Even though the questions have been kept at a high level they are formed to try to map the different national standards use of such things as frequency, guidance on monitoring position, distinction between different types of structures, requirement to the equipment and more. Furthermore a few initial questions have been raised on other environmental monitoring relevant for blasting. The respondents are national, cooperate or individual members of EFEE. The answers are experts in the use of explosives and vibration-monitoring in their respective countries. More than 60 have answered the questionnaire from 29 different countries. Mainly European as well as other nations including India, Israel, Nigeria, Saudi Arabia, UAE, USA, Greenland and Hong Kong. By analysing the incoming answers, the differences and similarities in vibration monitoring of the respondents has been clarified and mapped. Where possible other environmental monitoring has also been analysed. Where needed the different guidelines, standards and regulations have been visited to verify the answers and further elaborate on the comparison.

By Mohamed Ourriban, Stéphanie Somot, Éric Proulx, Jean-Sébastien Marois, Marjolaine Drouin, Paul Blatter, Ahmed Bouajila, Claude Gagnon

"The mining industry has to face increasing restrictions concerning the use of fresh water in Québec and throughout the world. Increasing recirculated water usage could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have a negative impact on mineral processing operations, thereby limiting the incentive for sustainable development initiatives. As a first step into selecting and testing remediation strategies, one of which being blending local waters, a mapping of process water quality (inorganic and organic fractions) allowed to locate zones in an industrial case study where fresh water is introduced into the circuit and to detect dissolution and precipitation zones. A complementary hydro-geochemical modeling study on water blends was also performed showing encouraging results towards the objectives of the project.INTRODUCTION The industry has to face increasing restrictions on the use of fresh water in Québec (Quebec Government, 2009) and throughout the world (Brown, 2003; UNESCO, 2006). The cost for the use of fresh water and for water management is highly variable and case-dependent (from 0.2 to up to 7 million dollars/year according to available private estimations, excluding the capital expenditure). It may be, or may become, significant for any plant; thus, risk assessment is of concern here. Using recirculated water could lead to a better control of the quality and the quantity of water supplied to the mineral processing units. Furthermore, it could reduce the volume of waste water to be managed and treated before its release to the environment. However, process water may have some positive and negative impacts on mineral processing operations (Janssen, 2003; Johnson, 2003; Rao and Finch, 1989). Negative impacts could limit the incentive for sustainable development initiatives. Water management strategies at mineral processing sites are supported both by a strategic plan and a water management plan. The strategic plan includes legal aspects, investment costs, potential benefits and various risk levels (Corder and Moran, 2006; Côte et al, 2006; Evans et al., 2006; MacIntosh and Merritt, 2003; McLellan et al., 2008; Merritt and MacIntosh, 2006; Robinson and Keddie, 2006; van Beers et al., 2007a; van Beers et al., 2007b; van Berkel, 2007). In practice, the strategic plan evaluates technical possibilities and costs of various scenarios, such as for example: bringing fresh water to the plant or recirculating waters, or using blends of both. Two important factors to consider in order to enhance the future production efficiency and to minimise risks are: the durability and the stability of the resource, both from quality and quantity points of view."

Jan 1, 2012

By B. P. Faulkner, M. Weinecke

Svedala started a development program in 1997 to develop a process to convert waste tires into valuable commodities. A review of numerous approaches revealed short-comings in the various approaches either process, mechanical, combination of factors, or trying to emphasis the production of low value products. A market study revealed that a process that could produce a good grade of carbon black would be economically feasible. This paper discusses the laboratory and pilot plant development and commercial plant design.

Jan 1, 2001

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau's annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By E. P. Hayes

This report supplements the date contained in Bureau of Mines Information Circular 6156, "Special features of core drilling in the salt beds of Western Texas and New Mexico," by J. S. Wroth. That circular dealt with the drilling of the first 12 of the 24 potash tests made by the U. S. Bureau of Mines in cooperation with the U. S. Geological Survey; this report is concerned with the drilling of the last 12 tests. ACKNOWLEDGMENTS The writer is indebted to R. E. Heithecker, the Bureau of Mines engineer who had charge of the drilling of tests 13 to 17, for his well-prepared records on the drilling of these tests.

Jan 1, 1933

By Elisa Alonso

Recycling is generally a more sustainable alternative to landfilling. Its financial costs however, do not always justify its practice, especially in the short term. As a result, even for precious metals such as platinum, significant amounts can end up unrecovered. In considering risks of materials scarcity for firms that require platinum and platinum products, this paper examines how recycling provides additional benefits as a risk-mitigating strategy against scarcity. The experimental platform for this examination is a System Dynamics simulation model that strives to capture the dynamics of platinum market supply, demand and price. The detailed structures of supply and demand are key features of the model. Results show that since the secondary supply of platinum depends on a supply chain separate from primary extraction, recycling can diversify the risks of primary supply instabilities and reduce the impact of price fluctuations upon firms.

Jan 1, 2009